scholarly journals Connection performance examination of a new bamboo-oriented strand board connector

BioResources ◽  
2021 ◽  
Vol 16 (2) ◽  
pp. 2906-2920
Author(s):  
Runmin Xu ◽  
Kaiting Zhang ◽  
Linyan Ren ◽  
Fuli Wang ◽  
Zhenzhen Zhu ◽  
...  
Keyword(s):  
Physical Properties ◽  
Joint Strength ◽  
Failure Modes ◽  
Oriented Strand Board ◽  
Bending Moment ◽  
Furniture Industry ◽  
Compression Tests ◽  
Tension And Compression ◽  
Cantilever Bending ◽  
Performance Examination

Bamboo-oriented strand board (BOSB) with superior physical properties can be used in the furniture industry to alleviate wood shortages. Two types of plug-in connectors were designed in this paper: a splint-type connector and V-type connector. By cantilever bending, corner tension, and compression tests of L-type corner joints of BOSB and wood-oriented strand board (WOSB), the connection performance of the new connectors and six typical connectors was compared. The new connectors function like clamps, do not require that a screw or bolt pass into or through the board, and can be assembled repeatedly. The V-type connectors were more suitable for BOSB, and the joints exhibited the highest ultimate bending moment values (133.9 N·m, 86.8 N·m, 117.7 N·m). The splint connectors were more suitable for WOSB and their ultimate bending moment values (57.1 N·m, 45.3 N·m, 61.3 N·m) were greater than the joints fixed by V-type connectors (50.4 N·m, 35.4 N·m, 46.1 N·m). The results revealed that the connector performance affects the joint strength and that different plates were suitable for different connectors. A joint failure analysis revealed two simple failure modes for the two new connectors.

Modelling the asymmetric tension–compression properties of additively manufactured alloys using continuum damage mechanics

2021 ◽  
pp. 146442072110134
Author(s):  
A Nayebi ◽  
H Rokhgireh ◽  
M Araghi ◽  
M Mohammadi
Keyword(s):  
Damage Mechanics ◽  
Continuum Damage Mechanics ◽  
Element Model ◽  
Continuum Damage ◽  
Compression Tests ◽  
Compression Properties ◽  
Mechanics Model ◽  
Stress Components ◽  
Tension And Compression ◽  
Closure Effect

Additively manufactured parts often comprise internal porosities due to the manufacturing process, which needs to be considered in modelling their mechanical behaviour. It was experimentally shown that additively manufactured parts’ tensile and compressive mechanical properties are different for various metallic alloys. In this study, isotropic continuum damage mechanics is used to model additively manufactured alloys’ tension and compression behaviours. Compressive stress components can shrink discontinuities present in additively manufactured alloys. Therefore, the crack closure effect was employed to describe different behaviours during uniaxial tension and compression tests. A finite element model embedded in an ABAQUS’s UMAT format was developed to account for the isotropic continuum damage mechanics model. The numerical results of tension and compression tests were compared with experimental observations for additively manufactured maraging steel, AlSi10Mg and Ti-6Al-4V. Stress–strain curves in tension and compression of these alloys were obtained using the continuum damage mechanics model and compared well with the experimental results.

Submarine Pipeline Installation JIP: Strength and Deformation Capacity of Pipes Passing Over the S-Lay Vessel Stinger

2006 ◽  
Author(s):  
Enrico Torselletti ◽  
Luigino Vitali ◽  
Erik Levold ◽  
Kim J. Mo̸rk
Keyword(s):  
Water Depth ◽  
Failure Modes ◽  
Bending Moment ◽  
External Pressure ◽  
Submarine Pipeline ◽  
Design Guideline ◽  
Moment Capacity ◽  
Sea Bottom ◽  
Major Vessel ◽  
Gas Fields

The development of deep water gas fields using trunklines to carry the gas to the markets is sometime limited by the feasibility/economics of the construction phase. In particular there is a market for using S-lay vessels in water depth larger than 1000m. The S-lay feasibility depends on the applicable tension at the tensioner which is a function of water depth, stinger length and stinger curvature (for given stinger length by its curvature). This means that, without major vessel up-grading and to avoid too long stingers that are prone to damages caused by environmental loads, the application of larger stinger curvatures than presently allowed by current regulations/state of the art is needed. The work presented in this paper is a result of the project “Development of a Design Guideline for Submarine Pipeline Installation” sponsored by STATOIL and HYDRO. The technical activities are performed in co-operation by DNV, STATOIL and SNAMPROGETTI. The scope of the project is to produce a LRFD (Load Resistant Factor Design) design guideline to be used in the definition and application of design criteria for the laying phase e.g. to S and J-lay methods/equipment. The guideline covers D/t from 15 to 45 and applied strains over the overbend in excess of 0.5%. This paper addresses the failure modes relevant for combined high curvatures/strains, axial, external pressure and local forces due to roller over the stinger of an S-lay vessel and to sea bottom contacts, particularly: • Residual pipe ovality after laying, • Maximum strain and bending moment capacity. Analytical equations are proposed in accordance with DNV OS F101 philosophy and design format.

Preliminary Parametric Assessment of a Bolted Endplate Joint under Combined Axial Force and Cyclic Bending Moment

2011 ◽  
Vol 255-260 ◽  
pp. 718-721
Author(s):  
Z.Y. Wang ◽  
Q.Y. Wang
Keyword(s):  
Finite Element Analysis ◽  
Axial Force ◽  
Seismic Design ◽  
Axial Load ◽  
Failure Modes ◽  
Bending Moment ◽  
Element Analysis ◽  
Cyclic Behaviour ◽  
Joint Behaviour ◽  
Steel Joints

Problems regarding the combined axial force and bending moment for the behaviour of semi-rigid steel joints under service loading have been recognized in recent studies. As an extended research on the cyclic behaviour of a bolted endplate joint, this study is performed relating to the contribution of column axial force on the cyclic behaviour of the joint. Using finite element analysis, the deteriorations of the joint performance have been evaluated. The preliminary parametric study of the joint is conducted with the consideration of flexibility of the column flange. The column axial force was observed to significantly influence the joint behaviour when the bending of the column flange dominates the failure modes. The reductions of moment resistance predicted by numerical analysis have been compared with codified suggestions. Comments have been made for further consideration of the influence of column axial load in seismic design of bolted endplate joints.

Tension and compression moduli characterization of a bimodular ceramic-fiber reinforced SiO2 aerogel composite

2020 ◽  
Vol 62 (10) ◽  
pp. 1003-1009
Author(s):  
Yantao Sun ◽  
Jia Huang ◽  
Duoqi Shi ◽  
Shengliang Zhang ◽  
Zhizhong Fu ◽  
...  
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
Image Correlation ◽  
Bending Test ◽  
Ceramic Fiber ◽  
Fiber Reinforced ◽  
Compression Tests ◽  
Tension Tests ◽  
Aerogel Composite ◽  
Tension And Compression

Abstract Comprehensive characterization mechanical properties of aerogels and their composites are important for engineering design. In particular, some aerogel composites were reported to have varied tension and compression moduli. But conducting tension tests is difficult for the reason that low strength and brittleness will lead to unexpected failure in the non-test area. A method is presented for measuring both the tension and compression moduli of a ceramic-fiber reinforced SiO2 aerogel composite by bending via digital image correlation. First, the relationship between bending behavior and the tension/compression moduli was introduced for bimodular materials. Then a bending test was conducted to predict tension and the compression moduli of the ceramicfiber- reinforced SiO2 aerogel composite via digital image correlation. In addition, uniaxial tension and compression tests of the aerogel composites were carried out, respectively for measuring tension and compression moduli. The tension and compression moduli measured were numerically similar to results obtained from uniaxial tests with a difference of less than 14 %.

A Validated Methodology to Establish Structural Capacities for Subsea Connector Families

2021 ◽  
Author(s):  
Michael John Stephens ◽  
Simon John Roberts ◽  
Derek James Bennet
Keyword(s):  
Failure Modes ◽  
Bending Moment ◽  
Full Scale ◽  
Structural Testing ◽  
Combined Loading ◽  
Test Sequence ◽  
Fea Model ◽  
Analysis Methodology ◽  
Industry Standards ◽  
Physical Testing

Abstract Understanding the structural limits of subsea connectors used in offshore environments is critical to ensure safe operations. The latest industry standards establish the requirement for physical testing to validate analysis methodologies for connector designs. In this paper, an analysis methodology, compliant with the latest API 17G standard, is presented for calculating structural capacities of non-preloaded connectors. The methodology has been developed for complex combined loading scenarios and validated using full-scale physical testing for different connector families. Detailed 3-D, non-linear, finite element models were developed for three different non-preloaded connections, which consisted of threaded and load shoulder connectors. A comprehensive set of combined tension and bending moment structural capacities at normal, extreme and survival conditions were calculated for each connection. The calculated capacities were validated for each connection by performing a test sequence using full-scale structural testing. A final tension or bending to failure test was also completed for each test connection to validate the physical failure mode, exceeding the latest API 17G requirements. For all connections tested, capacities calculated using the methodology were validated from the successful completion of the test sequences. The physical failure modes of the test connections also matched the predicted failure modes from the FEA, and the tensile or bending moment loading at physical collapse exceeded that predicted by the global collapse of the FEA model. Using the validated approach described in this paper significantly reduces the requirement of physical testing for connector families, establishing confidence in the structural limits that are critical for safe operations.

scholarly journals Evaluation of Reliefs’ Properties on Design of Thermoformed Packaging Using Fused Deposition Modelling Moulds.

Materials ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 478
Author(s):  
Lucía Rodríguez-Parada ◽  
Pedro F. Mayuet ◽  
Antonio J. Gámez
Keyword(s):  
Mechanical Properties ◽  
Physical Properties ◽  
Food Industry ◽  
Research Study ◽  
Comparative Data ◽  
Fused Deposition Modelling ◽  
Compression Tests ◽  
Fused Deposition ◽  
Packaging Industry

The increased consumption of food requiring thermoformed packaging implies that the packaging industry demands customized solutions in terms of shapes and sizes to make each packaging unique. In particular, food industry increasingly requires more transparent packaging, with greater clarity and a better presentation of the product they contain. However, in turn, the differentiation of packaging is sought through its geometry and quality, as well as the arrangement of food inside the packaging. In addition, these types of packaging usually include ribs in the walls to improve their physical properties. However, these ribs also affect the final aesthetics of the product. In accordance with this, this research study analyses the mechanical properties of different relief geometries that can affect not only their aesthetics but also their strength. For this purpose, tensile and compression tests were carried out using thermoformed PET sheets. The results provide comparative data on the reliefs studied and show that there are differences in the mechanical properties according to shape, size and disposition in the package.

scholarly journals Permeability Characteristic and Failure Behavior of Filled Cracked Rock in the Triaxial Seepage Experiment

2019 ◽  
Vol 2019 ◽  
pp. 1-12
Author(s):  
Xinyu Liu ◽  
Zhende Zhu ◽  
Aihua Liu
Keyword(s):  
Growth Rate ◽  
Rock Mass ◽  
Failure Modes ◽  
Peak Stress ◽  
Confining Pressure ◽  
Strength Characteristics ◽  
Failure Behavior ◽  
Compression Tests ◽  
Secondary Cracks ◽  
Safety And Stability

Filling is commonly found in natural cracked rock mass. As the weakest part of the rock, the filling properties directly affect the rock deformation and strength, permeability, and so on and affect the safety and stability of the rock mass engineering. In this study, a single slit has been preset in sandstones and filled with different physical properties materials. Based on the laboratory triaxial seepage test, the permeability and strength characteristics of filled cracked sandstones are analyzed, and the failure modes are obtained. The main findings of this study are as follows: (1) The permeability coefficient peak value of the filled cracked rock appears before the stress peak. (2) At the same confining pressure growth rate, the peak stress growth rate of the filled cracked rock is generally higher than that of the intact rock and the strength growth rate of the cracked rock increases with the length of the fracture. The strength characteristics of the filling in the uniaxial compression tests and triaxial seepage tests are significantly affected by the hydraulic properties. (3) The strength and permeability coefficients of cracked rock filled with cement mortar are more sensitive to the change of confining pressure, while under the same condition, the ones of cracked rock filled with gypsum mortar are stable. (4) According to the failure mechanism, under the seepage stress, the secondary cracks can be divided into 3 types and the failure modes can be divided into 2 types.

Bearing Capacity of Structures Made of Materials with Different Tensile and Compression Strengths

2019 ◽  
Vol 968 ◽  
pp. 200-208
Author(s):  
Mykola Soroka
Keyword(s):  
Cross Section ◽  
Rectangular Cross Section ◽  
Limit State ◽  
Analytical Calculation ◽  
Bending Moment ◽  
Maximum Load ◽  
Longitudinal Force ◽  
Plastic State ◽  
Limiting State ◽  
Tension And Compression

The paper considers the problem of the ultimate load finding for structures made of a material with different limits of tensile strength and compression. The modulus of elasticity under tension and compression is the same. It is assumed that upon reaching the ultimate strength, the material is deformed indefinitely. The calculations use a simplified material deformation diagram — Prandtl diagrams. The limiting state of a solid rectangular section under the action of a longitudinal force and a bending moment is considered. The dependences describing the boundary of the strength of a rectangular cross section are obtained. Formulas allowing the calculation of the values of the limit forces and under the action of which the cross section passes into the plastic state are derived. Examples of the analytical calculation of the maximum load for the frame and two-hinged arch are given. An algorithm is proposed and a program for calculating arbitrary flat rod systems according to the limit state using the finite element method is compiled. The proposed algorithm does not involve the use of iterative processes, which leads to an exact calculation of the maximum load within the accepted assumptions.

A FEA Simulation Model for Thin-Walled C-Section Composite Beam Assembling With R-Angle Deviation

2014 ◽  
Author(s):  
Hua Wang ◽  
Suo Si
Keyword(s):  
Numerical Model ◽  
Composite Beam ◽  
Failure Modes ◽  
Mechanical Performance ◽  
Element Model ◽  
Load Level ◽  
Compression Tests ◽  
Accurate Analysis ◽  
Angle Deviation ◽  
Thin Walled

There are unavoidable deviations, such as shrinkage and distortions, in the composite detail parts production due to the complexity of composites fabrication. Interests in the assembly analysis of composite beams have led to a need for more accurate analysis especially in the case of fabrication deviations. This work proposes a numerical finite element model of thin-walled C-section composite beam with R-angle deviation for assembling. The rule of Hashin failure combined with cohesive element is applied to study the mechanical performance of the fiber and matrix (implemented as user subroutine UMAT in ABAQUS) while positioning and clamping. Tension and compression tests are carried out based on available standards to determine the C-section beam behavior under load. The testing data validates the proposed numerical model. The numerical model captures the experimentally obtained results with minimal error, and predicts the failure modes successfully. The proposed model allows to determine accurately the first failure location and the associated load level. It will enhance the understanding of the composite components pre-loading analysis, and help systematically improving the composites assembling efficiency in civil aircraft industry.

Sign in / Sign up

Export Citation Format

Share Document