Application of magneto-optical method for detection of material structure changes

2021 ◽  
Vol 2021 (49) ◽  
pp. 32-36
Author(s):  
O. P. Maksymenko ◽  
◽  
O. D. Suriadova ◽  
Keyword(s):  
Spatial Resolution ◽  
Fatigue Cracks ◽  
High Sensitivity ◽  
Material Structure ◽  
Special Importance ◽  
Actual Length ◽  
Saturation Field ◽  
Wide Range ◽  
Paramagnetic Materials ◽  
Magneto Optic

The possibilities of magneto-optical sensors to control the damage of ferromagnetic and para-magnetic materials and products are considered. In the introduction it is shown that modern magneto-optical materials used in creating sensors have a high sensitivity and spatial resolution. So, on their basis it is possible to develop sensitive and informative means of non-destructive testing for a wide range of applications. For example, it is used to detect microcracks, corrosion damage, degradation changes in the material structure, surface deformations, and subsurface defects. The method ability to detect appearance of magnetic phases in paramagnetic materials, that are precursors of fracture, is of a special importance. The advantage of magneto-optic sensors is a large observation area and high spatial resolution. Resolution of the sensor is determined by the period and size of the domain structure, which averages 13...50 micrometres. High sensitivity of the sensor is due to a small saturation field of the magneto-optic material from 0.1 mT to 0.7 mT. In addition, these parameters are controlled by changing the temperature of the sensor, direction and intensity of the magnetic field. In this paper an optical scheme based on magneto-optical garnet film for visualization of fatigue cracks, which are formed in compact samples during their experimental investigation on fatigue failure is described. The developed scheme allowed us to visualize and fix position of the crack and determine its actual length, considering the closed part of the crack. A further direction of research will be to increase the sensitivity of the developed scheme and reduce the noise of magneto-optical images to identify the initial stages of the degradation process of ferromagnetic and paramagnetic materials and products.

Generalized Heterodyne Configurations for Photo-induced Force Microscopy

2019 ◽  
Author(s):  
Le Wang ◽  
Devon Jakob ◽  
Haomin Wang ◽  
Alexis Apostolos ◽  
Marcos M. Pires ◽  
...  
Keyword(s):  
Spatial Resolution ◽  
Repetition Rate ◽  
Modulation Frequency ◽  
High Harmonic ◽  
Chemical Imaging ◽  
Heterodyne Detection ◽  
Force Microscopy ◽  
Wide Range ◽  
The Difference ◽  
Afm Cantilever

<div>Infrared chemical microscopy through mechanical probing of light-matter interactions by atomic force microscopy (AFM) bypasses the diffraction limit. One increasingly popular technique is photo-induced force microscopy (PiFM), which utilizes the mechanical heterodyne signal detection between cantilever mechanical resonant oscillations and the photo induced force from light-matter interaction. So far, photo induced force microscopy has been operated in only one heterodyne configuration. In this article, we generalize heterodyne configurations of photoinduced force microscopy by introducing two new schemes: harmonic heterodyne detection and sequential heterodyne detection. In harmonic heterodyne detection, the laser repetition rate matches integer fractions of the difference between the two mechanical resonant modes of the AFM cantilever. The high harmonic of the beating from the photothermal expansion mixes with the AFM cantilever oscillation to provide PiFM signal. In sequential heterodyne detection, the combination of the repetition rate of laser pulses and polarization modulation frequency matches the difference between two AFM mechanical modes, leading to detectable PiFM signals. These two generalized heterodyne configurations for photo induced force microscopy deliver new avenues for chemical imaging and broadband spectroscopy at ~10 nm spatial resolution. They are suitable for a wide range of heterogeneous materials across various disciplines: from structured polymer film, polaritonic boron nitride materials, to isolated bacterial peptidoglycan cell walls. The generalized heterodyne configurations introduce flexibility for the implementation of PiFM and related tapping mode AFM-IR, and provide possibilities for additional modulation channel in PiFM for targeted signal extraction with nanoscale spatial resolution.</div>

scholarly journals Gold–Carbon Nanocomposites for Environmental Contaminant Sensing

Micromachines ◽  
2021 ◽  
Vol 12 (6) ◽  
pp. 719
Author(s):  
Shahrooz Rahmati ◽  
William Doherty ◽  
Arman Amani Babadi ◽  
Muhamad Syamim Akmal Che Mansor ◽  
Nurhidayatullaili Muhd Julkapli ◽  
...  
Keyword(s):  
Environmental Pollutants ◽  
High Sensitivity ◽  
Environmental Crisis ◽  
World Population ◽  
Chemical Contaminants ◽  
Carbon Nanocomposites ◽  
Minimal Sample ◽  
Wide Range ◽  
And Control ◽  
Analytical Tools

The environmental crisis, due to the rapid growth of the world population and globalisation, is a serious concern of this century. Nanoscience and nanotechnology play an important role in addressing a wide range of environmental issues with innovative and successful solutions. Identification and control of emerging chemical contaminants have received substantial interest in recent years. As a result, there is a need for reliable and rapid analytical tools capable of performing sample analysis with high sensitivity, broad selectivity, desired stability, and minimal sample handling for the detection, degradation, and removal of hazardous contaminants. In this review, various gold–carbon nanocomposites-based sensors/biosensors that have been developed thus far are explored. The electrochemical platforms, synthesis, diverse applications, and effective monitoring of environmental pollutants are investigated comparatively.

scholarly journals Pulsed Electromagnetic Cross-Well Exploration for Monitoring Permafrost and Examining the Processes of Its Geocryological Changes

Geosciences ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 60
Author(s):  
Viacheslav Glinskikh ◽  
Oleg Nechaev ◽  
Igor Mikhaylov ◽  
Kirill Danilovskiy ◽  
Vladimir Olenchenko
Keyword(s):  
High Performance ◽  
Geophysical Methods ◽  
Three Dimensional ◽  
High Sensitivity ◽  
Data Interpretation ◽  
Industrial Facilities ◽  
Wide Range ◽  
Vector Finite Element ◽  
A New Technique ◽  
Pulsed Electromagnetic

This paper is dedicated to the topical problem of examining permafrost’s state and the processes of its geocryological changes by means of geophysical methods. To monitor the cryolithozone, we proposed and scientifically substantiated a new technique of pulsed electromagnetic cross-well sounding. Based on the vector finite-element method, we created a mathematical model of the cross-well sounding process with a pulsed source in a three-dimensional spatially heterogeneous medium. A high-performance parallel computing algorithm was developed and verified. Through realistic geoelectric models of permafrost with a talik under a highway, constructed following the results of electrotomography field data interpretation, we numerically simulated the pulsed sounding on the computing resources of the Siberian Supercomputer Center of SB RAS. The simulation results suggest the proposed system of pulsed electromagnetic cross-well monitoring to be characterized by a high sensitivity to the presence and dimensions of the talik. The devised approach can be oriented to addressing a wide range of issues related to monitoring permafrost rocks under civil and industrial facilities, buildings, and constructions.

scholarly journals Overview of Popular Techniques of Raman Spectroscopy and Their Potential in the Study of Plant Tissues

Molecules ◽  
2021 ◽  
Vol 26 (6) ◽  
pp. 1537
Author(s):  
Aneta Saletnik ◽  
Bogdan Saletnik ◽  
Czesław Puchalski
Keyword(s):  
Raman Spectroscopy ◽  
Cell Walls ◽  
Structural Changes ◽  
Spatial Information ◽  
Technological Development ◽  
Analytical Techniques ◽  
High Sensitivity ◽  
Plant Tissues ◽  
Wide Range ◽  
Identification Technique

Raman spectroscopy is one of the main analytical techniques used in optical metrology. It is a vibration, marker-free technique that provides insight into the structure and composition of tissues and cells at the molecular level. Raman spectroscopy is an outstanding material identification technique. It provides spatial information of vibrations from complex biological samples which renders it a very accurate tool for the analysis of highly complex plant tissues. Raman spectra can be used as a fingerprint tool for a very wide range of compounds. Raman spectroscopy enables all the polymers that build the cell walls of plants to be tracked simultaneously; it facilitates the analysis of both the molecular composition and the molecular structure of cell walls. Due to its high sensitivity to even minute structural changes, this method is used for comparative tests. The introduction of new and improved Raman techniques by scientists as well as the constant technological development of the apparatus has resulted in an increased importance of Raman spectroscopy in the discovery and defining of tissues and the processes taking place in them.

Measurement of pulmonary edema in intact dogs by transthoracic gamma-ray attenuation

1979 ◽  
Vol 47 (6) ◽  
pp. 1228-1233 ◽  
Author(s):  
D. S. Simon ◽  
J. F. Murray ◽  
N. C. Staub
Keyword(s):  
Pulmonary Edema ◽  
Time Course ◽  
Gamma Ray ◽  
High Sensitivity ◽  
Lung Edema ◽  
Lung Water ◽  
Vascular Congestion ◽  
Isolated Lung ◽  
Wide Range ◽  
Gamma Ray Attenuation

We evaluated the attenuation of the 122 keV gamma ray of cobalt-57 across the thorax of anesthetized dogs as a method for following the time course of lung water changes in acute pulmonary edema induced by either increased microvascular permeability or increased microvascular hydrostatic pressure. The gamma rays traversed the thorax centered on the seventh rib laterally where the lung mass in the beam path was greatest. Calibration measurements in isolated lung lobes demonstrated the high sensitivity and inherent accuracy of the method over a wide range of lung water contents. In control dogs reproducibility averaged +/-3%. Increased permeability edema led to large rapid increases in the transthoracic gamma ray attenuation (TGA), while increased pressure caused an immediate, modest increase in TGA (vascular congestion) followed by a slow further increase over 2 h. There was a fairly good correlation between the increase in extravascular lung water and the change in TGA. The method is simple, safe, and noninvasive and appears to be useful for following the time course of lung water accumulation in generalized lung edema in anesthetized animals.

scholarly journals Measurement and analysis of gas-puff density distributions for plasma radiation source z pinches

2001 ◽  
Vol 19 (4) ◽  
pp. 579-595 ◽  
Author(s):  
D. MOSHER ◽  
B.V. WEBER ◽  
B. MOOSMAN ◽  
R.J. COMMISSO ◽  
P. COLEMAN ◽  
...  
Keyword(s):  
Radiation Source ◽  
Gas Flow ◽  
Initial Density ◽  
High Sensitivity ◽  
Plasma Radiation ◽  
Analysis Techniques ◽  
Density Distributions ◽  
Radiation Properties ◽  
Wide Range ◽  
Measurement And Analysis

High-sensitivity interferometry measurements of initial density distributions are reviewed for a wide range of gas-puff nozzles used in plasma radiation source (PRS) z-pinch experiments. Accurate gas distributions are required for determining experimental load parameters, modeling implosion dynamics, understanding the radiation properties of the stagnated pinch, and for predicting PRS performance in future experiments. For a number of these nozzles, a simple ballistic-gas-flow model (BFM) has been used to provide good physics-based analytic fits to the measured r, z density distributions. These BFM fits provide a convenient means to smoothly interpolate radial density distributions between discrete axial measurement locations for finer-zoned two-dimensional MHD calculations, and can be used to determine how changes in nozzle parameters and load geometry might alter implosion dynamics and radiation performance. These measurement and analysis techniques are demonstrated for a nested-shell nozzle used in Double Eagle and Saturn experiments. For this nozzle, the analysis suggests load modifications that may increase the K-shell yield.

Experimental Investigations on Aluminium Ultrasonic Welding Parameters

2014 ◽  
Vol 657 ◽  
pp. 306-310
Author(s):  
Lăcrămioara Apetrei ◽  
Vasile Rață ◽  
Ruxandra Rață ◽  
Elena Raluca Bulai
Keyword(s):  
Microstructural Analysis ◽  
Base Material ◽  
Welding Process ◽  
Ultrasonic Welding ◽  
Experimental Investigations ◽  
Welding Parameters ◽  
Material Structure ◽  
Welding Temperature ◽  
Wide Range ◽  
Made In

Research evolution timely tendencies, in the nonconventional technologies field, are: manufacture conditions optimization and complex equipments design. The increasing of ultrasonic machining use, in various technologies is due to the expanding need of a wide range materials and high quality manufacture standards in many activity fields. This paper present a experimental study made in order to analyze the welded zone material structure and welding quality. The effects of aluminium ultrasonic welding parameters such as relative energy, machining time, amplitude and working force were compared through traction tests values and microstructural analysis. Microhardness tests were, also, made in five different points, two in the base material and three in the welded zone, on each welded aluminium sample. The aluminum welding experiments were made at the National Research and Development Institute for Welding and Material Testing (ISIM) Timişoara. The ultrasonic welding temperature is lower than the aluminium melting temperature, that's so our experiments reveal that the aluminium ultrasonic welding process doesn't determine the appearance of moulding structure. In the joint we have only crystalline grains deformation, phase transformation and aluminium diffusion.

scholarly journals Scale dependence of cirrus heterogeneity effects. Part II: MODIS NIR and SWIR channels

2018 ◽  
Vol 18 (16) ◽  
pp. 12105-12121 ◽  
Author(s):  
Thomas Fauchez ◽  
Steven Platnick ◽  
Tamás Várnai ◽  
Kerry Meyer ◽  
Céline Cornet ◽  
...  
Keyword(s):  
Radiative Transfer ◽  
Spatial Resolution ◽  
Thermal Infrared ◽  
Radiative Effects ◽  
Ice Clouds ◽  
Plane Parallel ◽  
Wide Range ◽  
The Impact ◽  
Side Illumination

Abstract. In a context of global climate change, the understanding of the radiative role of clouds is crucial. On average, ice clouds such as cirrus have a significant positive radiative effect, but under some conditions the effect may be negative. However, many uncertainties remain regarding the role of ice clouds on Earth's radiative budget and in a changing climate. Global satellite observations are particularly well suited to monitoring clouds, retrieving their characteristics and inferring their radiative impact. To retrieve ice cloud properties (optical thickness and ice crystal effective size), current operational algorithms assume that each pixel of the observed scene is plane-parallel and homogeneous, and that there is no radiative connection between neighboring pixels. Yet these retrieval assumptions are far from accurate, as real radiative transfer is 3-D. This leads to the plane-parallel and homogeneous bias (PPHB) plus the independent pixel approximation bias (IPAB), which impacts both the estimation of top-of-the-atmosphere (TOA) radiation and the retrievals. An important factor that determines the impact of these assumptions is the sensor spatial resolution. High-spatial-resolution pixels can better represent cloud variability (low PPHB), but the radiative path through the cloud can involve many pixels (high IPAB). In contrast, low-spatial-resolution pixels poorly represent the cloud variability (high PPHB), but the radiation is better contained within the pixel field of view (low IPAB). In addition, the solar and viewing geometry (as well as cloud optical properties) can modulate the magnitude of the PPHB and IPAB. In this, Part II of our study, we simulate TOA 0.86 and 2.13 µm solar reflectances over a cirrus uncinus scene produced by the 3DCLOUD model. Then, 3-D radiative transfer simulations are performed with the 3DMCPOL code at spatial resolutions ranging from 50 m to 10 km, for 12 viewing geometries and nine solar geometries. It is found that, for simulated nadir observations taken at resolution higher than 2.5 km, horizontal radiation transport (HRT) dominates biases between 3-D and 1-D reflectance calculations, but these biases are mitigated by the side illumination and shadowing effects for off-zenith solar geometries. At resolutions coarser than 2.5 km, PPHB dominates. For off-nadir observations at resolutions higher than 2.5 km, the effect that we call THEAB (tilted and homogeneous extinction approximation bias) due to the oblique line of sight passing through many cloud columns contributes to a large increase of the reflectances, but 3-D radiative effects such as shadowing and side illumination for oblique Sun are also important. At resolutions coarser than 2.5 km, the PPHB is again the dominant effect. The magnitude and resolution dependence of PPHB and IPAB is very different for visible, near-infrared and shortwave infrared channels compared with the thermal infrared channels discussed in Part I of this study. The contrast of 3-D radiative effects between solar and thermal infrared channels may be a significant issue for retrieval techniques that simultaneously use radiative measurements across a wide range of solar reflectance and infrared wavelengths.

Sign in / Sign up

Export Citation Format

Share Document