scholarly journals Effect of ultrafine natural steatite powder, super plasticizer and VMA on the fresh and hardened properties of self-compacting cement paste and mortar

2021 ◽  
Author(s):  
S. Christopher Gnanaraj ◽  
Ramesh Babu Chokkalingam ◽  
G. Lizia Thankam ◽  
S.K.M. Pothinathan
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Water Demand ◽  
Construction Material ◽  
Setting Time ◽  
Mineral Admixture ◽  
Self Healing ◽  
Chemical Admixtures ◽  
Hardened Properties ◽  
Viscosity Modifying Admixture

AbstractFor the past few decades innovation in construction material has grown a lot. This leads to special concrete such as self-compacting concrete, geopolymer concrete, self-healing concrete, etc. To prepare a special concrete apart from regular concreting material some sort of special materials was also needed, like mineral and chemical admixtures. Hence it is necessary to study the effect of these admixtures in cement paste and mortar before studying the same in concrete. Hence an attempt is made to study the effect of mineral and chemical admixtures in the fresh and hardened properties of cement paste and mortar. For this study ultrafine natural steatite powder is taken as mineral admixture and polycarboxylic based superplasticizer and glenium stream 2 were taken as chemical admixtures. Ultrafine natural steatite powder was used as additive to cement in various percentages like 0%, 5%, 10%, 15%, 20% and 25%. Superplasticizer and viscosity modifying admixture were taken as 1.5% and 0.5%, respectively. Then various combinations were worked out. To study the fresh property of cement paste consistency, initial setting time and miniature slump cone test were done based on the results yield stress of cement paste also calculated empirically. To study the hardened property compression test on cement mortar was done. Based on the test results it is clear that the addition of ultrafine natural steatite powder increases the water demand hence reduces the workability. On the other hand, it increases the compressive strength up to a certain limit. Adding superplasticizer increases the workability and reduces the water demand and viscosity modifying admixture reduces the bleeding and segregation effects hence increases the compressive strength.

scholarly journals Preparation of Electric- and Magnetic-Activated Water and Its Influence on the Workability and Mechanical Properties of Cement Mortar

2021 ◽  
Vol 13 (8) ◽  
pp. 4546
Author(s):  
Kaiyue Zhao ◽  
Peng Zhang ◽  
Bing Wang ◽  
Yupeng Tian ◽  
Shanbin Xue ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Cement Paste ◽  
Cement Mortar ◽  
Environmental Issues ◽  
Chemical Admixtures ◽  
Untreated Water ◽  
Alternating Voltage

Cement-based materials prepared with activated water induced by a magnetic field or electric field represent a possible solution to environmental issues caused by the worldwide utilization of chemical admixtures. In this contribution, electric- and magnetic-activated water have been produced. The workability and mechanical properties of cement mortar prepared with this activated water have been investigated. The results indicate that the pH and absorbance (Abs) values of the water varied as the electric and magnetic field changed, and their values increased significantly, exhibiting improved activity compared with that of the untreated water. In addition, activated water still retains activity within 30 min of the resting time. The fluidity of the cement paste prepared with electric-activated water was significantly larger than that of the untreated paste. However, the level of improvement differed with the worst performance resulting from cement paste prepared with alternating voltage activated water. In terms of mechanical properties, both compressive strength and flexural strength obtained its maximum values at 280 mT with two processing cycles. The compressive strength increased 26% as the curing time increased from 7 days to 28 days and flexural strength increased by 31%. In addition, through the introduction of magnetic-activated water into cement mortar, the mechanical strength can be maintained without losing its workability when the amount of cement is reduced.

scholarly journals Effect of Calcium Nitrate on the Properties of Portland–Limestone Cement-Based Concrete Cured at Low Temperature

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1611
Author(s):  
Gintautas Skripkiūnas ◽  
Asta Kičaitė ◽  
Harald Justnes ◽  
Ina Pundienė
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Setting Time ◽  
Calcium Nitrate ◽  
Curing Temperature ◽  
Hardened Concrete ◽  
Cement Pastes ◽  
Initial Setting Time ◽  
Initial Setting ◽  
Early Strength

The effect of calcium nitrate (CN) dosages from 0 to 3% (of cement mass) on the properties of fresh cement paste rheology and hardening processes and on the strength of hardened concrete with two types of limestone-blended composite cements (CEM II A-LL 42.5 R and 42.5 N) at different initial (two-day) curing temperatures (−10 °C to +20 °C) is presented. The rheology results showed that a CN dosage up to 1.5% works as a plasticizing admixture, while higher amounts demonstrate the effect of increasing viscosity. At higher CN content, the viscosity growth in normal early strength (N type) cement pastes is much slower than in high early strength (R type) cement pastes. For both cement-type pastes, shortening the initial and final setting times is more effective when using 3% at +5 °C and 0 °C. At these temperatures, the use of 3% CN reduces the initial setting time for high early strength paste by 7.4 and 5.4 times and for normal early strength cement paste by 3.5 and 3.4 times when compared to a CN-free cement paste. The most efficient use of CN is achieved at −5 °C for compressive strength enlargement; a 1% CN dosage ensures the compressive strength of samples at a −5 °C initial curing temperature, with high early strength cement exceeding 3.5 MPa but being less than the required 3.5 MPa in samples with normal early strength cement.

scholarly journals Effect of Waste Clay Brick Powder on Physical and Mechanical Properties of Cement Paste

2021 ◽  
Vol 15 (1) ◽  
pp. 370-380
Author(s):  
David Sinkhonde ◽  
Richard Ocharo Onchiri ◽  
Walter Odhiambo Oyawa ◽  
John Nyiro Mwero
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Setting Time ◽  
Partial Replacement ◽  
Clay Brick ◽  
X Ray ◽  
Cement Replacement ◽  
Clay Bricks ◽  
Brick Powder ◽  
Scanning Electron

Background: Investigations on the use of waste clay brick powder in concrete have been extensively conducted, but the analysis of waste clay brick powder effects on cement paste is limited. Materials and Methods: This paper discusses the effects of waste clay brick powder on cement paste. Fragmented clay bricks were grounded in the laboratory using a ball mill and incorporated into cementitious mixes as partial replacement of Ordinary Portland Cement. Workability, consistency, setting time, density and compressive strength properties of paste mixes were investigated to better understand the impact of waste clay brick powder on the cementitious paste. Four cement replacement levels of 2.5%, 5%, 7.5% and 10% were evaluated in comparison with the control paste. The chemical and mineral compositions were evaluated using X-Ray Fluorescence and X-Ray Diffractometer, respectively. The morphology of cement and waste clay brick powder was examined using a scanning electron microscope. Results: The investigation of workability exhibited a reduction of slump attributed to the significant addition of waste clay brick powder into the cementitious mixes, and it was concluded that waste clay brick powder did not significantly influence the density of the mixes. In comparison with the control paste, increased values of consistency and setting time of cement paste containing waste clay brick powder confirmed the information available in the literature. Conclusion: Although waste clay brick powder decreased the compressive strength of cement paste, 5% partial cement replacement with waste clay brick powder was established as an optimum percentage for specimens containing waste clay brick powder following curing periods of 7 and 28 days. Findings of chemical composition, mineral composition and scanning electron microscopy of waste clay brick powder demonstrated that when finely ground, fragmented clay bricks can be used in concrete as a pozzolanic material.

scholarly journals Effects of microbial agents to the properties of fly ash-based paste

2018 ◽  
Vol 195 ◽  
pp. 01012
Author(s):  
Kiki Dwi Wulandari ◽  
Januarti Jaya Ekaputri ◽  
Triwulan ◽  
Chikako Fujiyama ◽  
Davin H. E. Setiamarga
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Cement Paste ◽  
Construction Material ◽  
Concrete Strength ◽  
Self Healing ◽  
Concrete Mixtures ◽  
Microbial Agents ◽  
Portland Cement Paste ◽  
Geopolymer Paste

Specific microbial agents such as bacteria are often used in concrete to improve its performance. Some microbes act as self-healing agents to close cracks in concrete, and to increase concrete strength. This paper presents a study to observe the effects of microbe addition to two types of concrete mixtures the fly ash-based, as geopolymer paste, and portland cement paste containing fly ash. Furthermore, the investigation was conducted to compare the properties of each paste, such as its compressive strengths, specific gravities, porosity, microstructures, and XRay diffracting properties. The results indicate that microbial activities positively affected the properties of both, portland cement paste and geopolymer paste. The result reported here strongly suggests that fly ash can be used to produce a high quality, but environmental friendly construction material when it’s mixed together with useful microbes.

scholarly journals PROPERTIES OF CEMENT PASTE AND CONCRETE CONTAINING CALCIUM CARBIDE WASTE AS ADDITIVE

2016 ◽  
Vol 36 (1) ◽  
pp. 26-31
Author(s):  
EN Ogork ◽  
TS Ibrahim
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Setting Time ◽  
Drying Shrinkage ◽  
Calcium Carbide ◽  
Linear Shrinkage ◽  
Hardened Concrete ◽  
Concrete Compressive Strength ◽  
Initial Setting Time ◽  
Standard Procedures

This paper assessed the effect of calcium carbide waste (CCW) as additive on the properties of cement paste and concrete. The CCW used was sourced from a local panel beating workshop. It was sundried and sieved through a 75 µm sieve and characterized by X-Ray Fluorescence (XRF) analytical method. The consistency, setting times and drying linear shrinkage of cement paste with CCW addition of 0, 0.25, 0.5, 0.75 and 1.0 %, respectively by weight of cement were investigated in accordance with standard procedures. The slump values of fresh concrete containing CCW as additive and of 1:2:4 mix ratio and water-cement ratio of 0.5 was determined. A total of sixty numbers of 150 mm cubes of hardened concrete were tested for compressive strength at 1, 3, 7, 28 and 56 days of curing in accordance with standard procedures. The concrete compressive strength was also modeled using Minitab statistical software based on linear regression technique. The results of the investigations showed that CCW was predominantly of calcium oxide (95.69 %) and a combined SiO2, Al2O3 and Fe2O3 content of 3.14 %. The addition of CCW in cement decreased drying shrinkage (100 %), initial setting time (78 %) and final setting time (57 %), but increased consistency (14 %) at 1.0 % CCW content. The addition of CCW in concrete also showed slight increase in slump (6.5 %) and increase in compressive strength with increase in CCW additive up to 0.5 % and decrease in compressive strength with further increase in CCW content. The 28 days compressive strength of concrete with 0.5 % CCW content was 6.4 % more than normal, while that of concrete with 1.0 % CCW content was 14.9 % less than normal. The compressive strength model of CCW-concrete was developed with R2 value of 0.830 and could be used to predict concrete compressive strength. http://dx.doi.org/10.4314/njt.v36i1.4

scholarly journals Effects of Seawater on Setting Time and Compressive Strength of Concretes with Different Richness

2021 ◽  
Vol 7 (5) ◽  
pp. 857-865
Author(s):  
Ahmed I. Ghazal ◽  
Mohammed Y. El-Sheikh ◽  
Ahmed H. Abd El-Rahim
Keyword(s):  
Compressive Strength ◽  
Beneficial Effect ◽  
Fresh Water ◽  
Cement Paste ◽  
Detrimental Effect ◽  
Tap Water ◽  
Concrete Strength ◽  
Setting Time ◽  
Strength Tests ◽  
Initial Setting

Water is one of the main constituents of concrete. Although many types of water exist, fresh water is the mostly used in concrete industry. Fresh water is expected to be in a great shortage by 2050 according to UN world water development report. Incorporating seawater in concrete mixture can help in the expected problem of scarcity of fresh water. Also, in many cases seawater may be the only available water especially in coastal regions. Many reports mention various possibilities of using seawater in concrete without detrimental effect on concrete properties. In this study another beneficial effect of seawater over tap water was concluded. Setting tests of cement paste mixed with seawater was determined using Vicat apparatus and compared to tap water. Compressive strength tests at the age of 28 days of Portland cement concretes with varied quantity of cement i.e. 300, 350, 400, 450, and 500 kg, and mixed with seawater was also performed and compared to tap water. The results show that seawater affects standard consistency of cement paste and two percent increase was required in order to attain the same consistency as tap water. It shows also seawater slightly accelerates initial setting of cement but the effect is not so pronounced so as to cause a trouble in concrete and final setting time almost remains unaltered. Compressive strength tests show an increase in concrete strength mixed with seawater for all tested mixtures and depending on quantity of cement. It also shows a beneficial effect of seawater on compressive strength of rich concrete with quantity of cement 450 and 500 kg over tap water. Doi: 10.28991/cej-2021-03091695 Full Text: PDF

Effect of Eggshell Waste Powder on Impact Resistance and Bond Charcteristics of Reinforced Concrete

2020 ◽  
Vol 870 ◽  
pp. 21-28
Author(s):  
Dhifaf Natiq Hamdullah ◽  
Sheelan Mahmoud Hama ◽  
Mohammed Maher Yaseen
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Bond Strength ◽  
Setting Time ◽  
Impact Resistance ◽  
Unit Weight ◽  
Partial Replacement ◽  
Hardened Properties ◽  
Powder Content ◽  
Eggshell Waste

This research studied the effect of eggshell powder as a partial replacement of cement on fresh and hardened properties of concrete. The cement was partially replaced with eggshell powder at these percentage 0%, 2.5 %, 5 %, 7.5% and 10%, (by weight of cement). The resulting concrete was compared for impact resistance, energy absorption, load-slip characteristics and ultimate bond strength. setting time (initial and final), slump, density and compressive strength also have been found. The obtaining results indicated the advantage of incorporation of eggshell powder in concrete. The concrete unit weight has not obviously affected by eggshell powder content. The 2.5% eggshell powder give the best results compared to reference mix.

Mechanical and Microstructure Study of the Self Healing Bacterial Concrete

2019 ◽  
Vol 969 ◽  
pp. 472-477
Author(s):  
Sachin Tiwari ◽  
Shilpa Pal ◽  
Rekha Puria ◽  
Vikrant Nain ◽  
Rajendra Prasad Pathak
Keyword(s):  
Compressive Strength ◽  
Bacillus Megaterium ◽  
Construction Material ◽  
Research Work ◽  
Bacillus Sphaericus ◽  
Maximum Amount ◽  
The Self ◽  
Self Healing ◽  
Scanning Electron ◽  
Bacterial Concrete

Concrete largely used for construction material, degrades with the development of cracks that becomes easy passage for entry of chemicals and harmful compounds. Self healing capability is helpful to mitigate the deterioration of the concrete structures. This research work focuses on the self healing behaviour and mechanical properties of the bioconcrete supplemented with three different bacteria namely Bacillus sphaericus, Bacillus cohnii and Bacillus megaterium. Concrete supplemented with Bacillus cohnii exhibited 35.31% increase in compressive strength compared to control mix after 28 days. Concrete supplemented with other bacteria Bacillus sphaericus and Bacillus megaterium also showed enhanced compressive strength. Interestingly, addition of bacteria aided in healing of artificially generated cracks by formation of CaCO3 minerals. Maximum amount of healing (bacterial precipitation) which could be quantified as calcite minerals present in the bacterial concrete was 11.44% with B. cohnii confirmed by the Scanning Electron Microscope (SEM) with Energy Dispersive Spectroscopy (EDS).

Influence of Ultrafine Addition Obtained from Pre-Hydrated Cement on Cement Paste

2020 ◽  
Vol 992 ◽  
pp. 92-97
Author(s):  
Svetlana V. Samchenko ◽  
E.S. Egorov
Keyword(s):  
Cement Paste ◽  
Water Demand ◽  
Setting Time ◽  
Particle Dispersion ◽  
Crystalline Hydrate ◽  
Hydrated Cement ◽  
Forced Mixing ◽  
Paste Properties

This article focuses to influence of a pre-hydrated cement suspensions on hardening cement paste properties investigation. The pre-hydration was occurred by 2-th, 4-th 6-th hours during forced mixing. Changes of particle dispersion caused by hydration were determined. It is shown that by hydrolysis increase particles dispersion and subsequently increases quantity of new hydrate formations. Influence of the pre-hydrated cement suspensions on hardening cement paste properties is determined. It is shown that application pre-hydrated addition leads to increasing a cement paste water demand by 12, 17 and 14% for duration of hydration by 2, 4 and 6 hours consequently and to decreasing setting time. It caused by generating supplementary new formations of crystalline hydrate with subsequently increasing rate cement paste structuration. Rate of hardening was increased with increasing duration of the pre-hydration for 10% pre-hydrated cement addition. Obtained results may recommended the addition of pre-hydrated cement in form of cement suspension as cement gel for concrete nanomodification

scholarly journals Comparison of Effects of Sodium Bicarbonate and Sodium Carbonate on the Hydration and Properties of Portland Cement Paste

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1033 ◽  
Author(s):  
Yuli Wang ◽  
Fengxia He ◽  
Junjie Wang ◽  
Qianku Hu
Keyword(s):  
Compressive Strength ◽  
Sodium Bicarbonate ◽  
Portland Cement ◽  
Cement Paste ◽  
Sodium Carbonate ◽  
Ordinary Portland Cement ◽  
Setting Time ◽  
Sprayed Concrete ◽  
Final Setting Time ◽  
Portland Cement Paste

Carbonates and bicarbonates are two groups of accelerators which can be used in sprayed concrete. In this study, the effects of the two accelerators sodium carbonate (Na2CO3) and sodium bicarbonate (NaHCO3) (0%, 1%, 2%, 3%, and 4% by weight of ordinary Portland cement OPC) on the properties of OPC paste were compared. The results show that both of them could accelerate the initial and final setting time of OPC paste, but the effect of the two accelerators on the compressive strength were different. After 1 day, sodium bicarbonate at 3% had the highest strength while sodium carbonate at 1% had the highest strength. After 7 days, both of the two accelerators at 1% had the highest compressive strength. After 28 days, the compressive strength decreased with the increase of the two. The improved strength at 1 and 7 days was caused by the accelerated formation of ettringite and the formation of CaCO3 through the reactions between the two with portlandite. The decrease of strength was caused by the Na+ could reduce the adhesion between C-S-H gel by replacing the Ca2+. NaHCO3 was found be a better accelerator than Na2CO3.

Sign in / Sign up

Export Citation Format

Share Document