Precipitation- and stress-influenced coarsening in Mg-based Mg–Zn–Sn–Y and Mg–Zn–Sn–Sb alloys

2008 ◽  
Vol 23 (5) ◽  
pp. 1228-1236 ◽  
Author(s):  
Anton Gorny ◽  
Alexander Katsman
Keyword(s):  
Electron Microscopy ◽  
Research Work ◽  
Mutual Orientation ◽  
Face Centered Cubic ◽  
Two Phase ◽  
X Ray ◽  
High Resolution Tem ◽  
Interphase Boundaries ◽  
Different Temperatures ◽  
The Face

Extensive experimental research work has been carried out to investigate precipitation peculiarities in Mg–Zn–Sn-based alloys during aging at different temperatures. This in-depth research was conducted on Mg–4.4wt%Zn–4.0wt%Sn–0.6wt%Y and Mg–4.4wt%Zn–4.4wt%Sn–1.1wt%Sb using x-ray diffraction (XRD), transmission electron microscopy (TEM) including high-resolution TEM, and scanning electron microscopy (SEM) equipped with an energy-dispersive x-ray spectrometer (EDS). It was found that, first, a hexagonal close-packed (hcp)-MgZn2 phase nucleates and grows in the form of needles having coherent interphase boundaries with α-Mg matrix. Then the face-centered cubic (fcc)-Mg2Sn-phase nucleates heterogeneously, mainly at the tips of MgZn2 needles. A very certain mutual orientation of crystal lattices of MgZn2, Mg2Sn, and α-Mg matrix was revealed. The orientation of Mg2Sn precipitates is perpendicular to that of MgZn2 needles. They grow in the form of plates parallel to the basal planes of α-Mg matrix. Two-phase T-like particles are very typical of alloys aged for 1 to 16 days at 175 to 225 °C. The width/length ratio of MgZn2 needles inside T-like particles differs substantially from that found in single needles. The elastic/surface energy balance of needles and its influence on the morphology and coarsening behavior has been analyzed.

Precipitation Sequence in Mg-Zn-Sn Based Alloys

2006 ◽  
Vol 979 ◽  
Author(s):  
Anton Gorny ◽  
Alexander Katsman ◽  
Dmitry Shepelev ◽  
Menahem Bamberger
Keyword(s):  
Surface Energy Balance ◽  
Research Work ◽  
Precipitation Sequence ◽  
Elastic Surface ◽  
Two Phase ◽  
High Resolution Tem ◽  
Interphase Boundaries ◽  
Different Temperatures ◽  
The One ◽  
Mgzn2 Phase

AbstractExtensive experimental research work has been carried out in order to develop an Mg-Zn-Sn based creep resistant alloy. It was found that the addition of Y improves the structural stability of this alloy. The main goal of this work was to investigate precipitation sequence in Mg-Zn-Sn-Y alloys during aging at different temperatures. In order to elucidate the sequence of phase formation, XRD, TEM, SEM and EDS analyses were applied. It was found that, firstly, an hcp-MgZn2 phase nucleates homogeneously, and grows in the form of needles having coherent interphase boundaries with Mg-matrix. High-resolution TEM images in combination with Fourier transformed images reveal a topotaxial orientation relationship which is given by {110}MgZn2 <100>MgZn2∥(002)α-Mg<110>α-Mg. The cubic fcc Mg2Sn-phase nucleates heterogeneously, mainly at the tips of MgZn2-needles when the needle's width reaches a certain critical value. The orientation of Mg2Sn-precipitates is usually perpendicular to the one of MgZn2-needles. Two-phase T-like particles are very typical of alloys aged for 1-16 days at 175-225C. The width/length ratio of MgZn2-needles inside T-like particles differs substantially from the one found in single needles. The elastic/surface energy balance of needles and its influence on the morphology and coarsening behaviour has been analyzed.

scholarly journals Revisiting the Bøggild Intergrowth in Iridescent Labradorite Feldspars: Ordering, Kinetics, and Phase Equilibria

Minerals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 727
Author(s):  
Shiyun Jin ◽  
Huifang Xu ◽  
Seungyeol Lee
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Atom Probe ◽  
Phase Region ◽  
Two Phase ◽  
Subsolidus Phase ◽  
Plagioclase Feldspar ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Transmission

The enigmatic Bøggild intergrowth in iridescent labradorite crystals was revisited in light of recent work on the incommensurately modulated structures in the intermediated plagioclase. Five igneous samples and one metamorphic labradorite sample with various compositions and lamellar thicknesses were studied in this paper. The lamellar textures were characterized with conventional transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM). The compositions of individual lamellae were analyzed with high-resolution energy-dispersive X-ray spectroscopy (EDS) mapping and atom probe tomography (APT). The average structure states of the studied samples were also compared with single-crystal X-ray diffraction data (SC-XRD). The Na-rich lamellae have a composition of An44–48, and the Ca-rich lamellae range from An56 to An63. Significant differences between the lamellar compositions of different samples were observed. The compositions of the Bøggild intergrowth do not only depend on the bulk compositions, but also on the thermal history of the host rock. The implications on the subsolidus phase relationships of the plagioclase feldspar solid solution are discussed. The results cannot be explained by a regular symmetrical solvus such as the Bøggild gap, but they support an inclined two-phase region that closes at low temperature.

BIOSYNTHESIZED SILVER NANOPARTICLES USING CATHARANTHUS ROSEUS AND THEIR ANTIBACTERIAL EFFICACY IN SYNERGY WITH ANTIBIOTICS; A FUTURE ADVANCEMENT IN NANOMEDICINE

2021 ◽  
pp. 116-124
Author(s):  
MONIKA GUPTA
Keyword(s):  
Electron Microscopy ◽  
Silver Nanoparticles ◽  
Catharanthus Roseus ◽  
Leaf Extract ◽  
Research Work ◽  
Resistant Bacteria ◽  
Surface Plasmon Resonance Peak ◽  
Plasmon Resonance Peak ◽  
X Ray ◽  
Uniform Dispersion

Objective: This research work develops an approach to synthesize silver nanoparticles (AgNPs) by reduction of leaf extract of Catharanthus roseus plant. This study produces synthesized nanoparticles that have process-controlled attributes which make their antibiotic action highly efficient. These attributes include smaller size, proper morphology, uniform dispersion, metal ion content, and formation of functional groups. By optimizing the reduction process parameters, AgNPs gain the desired properties.  Methods: The biosynthesis of AgNPs process was performed using reaction of 10% (w/v) C. roseus leaf extract with AgNO3. The optimum conditions and concentration used for synthesis of nanoparticles were: 1 mM AgNO3, pH 5, and temperature 80°C with an incubation time of 72 h. All the above parameters were analyzed by ultraviolet-visible spectrophotometer with the surface plasmon resonance peak obtained at 440 nm. Results: Various characterization techniques were performed, namely, scanning electron microscopy, energy-dispersive X-ray, transmission electron microscopy, photoluminescence study, X-ray diffraction spectroscopy, Fourier transform infrared, dynamic light scattering, and atomic force microscopy. The results obtained from characterization confirmed the spherical morphology of the nanoparticles with size between 50 and 87 nm. In the current investigation, the antimicrobial activity of biosynthesized AgNPs was also determined using minimum inhibitory concentration and zone of inhibition methods against six different bacteria at different doses of AgNPs (100, 150, and 200 μg/ml) alone and also in combination with antibiotic-streptomycin. Conclusion: The results revealed that high concentration of AgNPs inhibits the bacterial growth. Furthermore, AgNPs revealed much stronger antibacterial action in synergy with streptomycin against antibiotic-resistant bacteria.

scholarly journals Green Synthesis and Catalytic Activity of Silver Nanoparticles Based on Piper chaba Stem Extracts

Nanomaterials ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1777 ◽  
Author(s):  
Md. Mahiuddin ◽  
Prianka Saha ◽  
Bungo Ochiai
Keyword(s):  
Electron Microscopy ◽  
Silver Nanoparticles ◽  
Green Synthesis ◽  
Ftir Spectroscopy ◽  
Visual Observation ◽  
Face Centered Cubic ◽  
X Ray ◽  
Vis Spectroscopy ◽  
Face Centered ◽  
Average Size

A green synthesis of silver nanoparticles (AgNPs) was conducted using the stem extract of Piper chaba, which is a plant abundantly growing in South and Southeast Asia. The synthesis was carried out at different reaction conditions, i.e., reaction temperature, concentrations of the extract and silver nitrate, reaction time, and pH. The synthesized AgNPs were characterized by visual observation, ultraviolet–visible (UV-vis) spectroscopy, dynamic light scattering (DLS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), x-ray diffraction (XRD), energy dispersive x-ray (EDX), and Fourier transform infrared (FTIR) spectroscopy. The characterization results revealed that AgNPs were uniformly dispersed and exhibited a moderate size distribution. They were mostly spherical crystals with face-centered cubic structures and an average size of 19 nm. The FTIR spectroscopy and DLS analysis indicated that the phytochemicals capping the surface of AgNPs stabilize the dispersion through anionic repulsion. The synthesized AgNPs effectively catalyzed the reduction of 4-nitrophenol (4-NP) and degradation of methylene blue (MB) in the presence of sodium borohydride.

Microstructure and Properties of Nanosemicrystalline Si3N4 Ceramics with Doped Sintering Additives: Part II. Phase Transformation and Microstructural Control

1998 ◽  
Vol 13 (9) ◽  
pp. 2588-2596 ◽  
Author(s):  
K. H. Ryu ◽  
J-M. Yang
Keyword(s):  
Electron Microscopy ◽  
Pressureless Sintering ◽  
Particle Sizes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sintering Additives ◽  
Different Temperatures ◽  
Si3n4 Ceramics ◽  
Scanning Electron ◽  
Microstructural Control

The low temperature pressureless sintering of a nanosized Si3N4 powder with doped sintering additives was investigated. The microstructural evolution during sintering at different temperatures was analyzed using x-ray diffraction and scanning electron microscopy. The effect of using nanosized Si3N4 powder as a catalyst to accelerate the α→β–Si3N4 transformation of a commercial Si3N4 powder with larger particle sizes was also investigated. Finally, two stage sintering was used to study the feasibility of controlling the microstructure and the mechanical properties of the nanosized silicon nitride.

Formation of the cementite crystal in austenite by transformation of triangulated polyhedra

2019 ◽  
Vol 75 (3) ◽  
pp. 325-332
Author(s):  
V. S. Kraposhin ◽  
N. D. Simich-Lafitskiy ◽  
A. L. Talis ◽  
A. A. Everstov ◽  
M. Yu. Semenov
Keyword(s):  
Interatomic Potential ◽  
Mutual Orientation ◽  
Crystallographic Group ◽  
Mutual Transformation ◽  
Face Centered Cubic ◽  
Body Centered Cubic ◽  
Orientation Relationships ◽  
The Face ◽  
Infinite Crystal ◽  
Face Centered

A mechanism is proposed for the nucleus formation at the mutual transformation of austenite and cementite crystals. The mechanism is founded on the interpretation of the considered structures as crystallographic tiling onto non-intersecting rods of triangulated polyhedra. A 15-vertex fragment of this linear substructure of austenite (cementite) can be transformed by diagonal flipping in a rhombus consisting of two adjacent triangular faces into a 15-vertex fragment of cementite (austenite). In the case of the mutual austenite–cementite transformation, the mutual orientation of the initial and final fragments coincides with the Thomson–Howell orientation relationships which are experimentally observed [Thompson & Howell (1988). Scr. Metall. 22, 229–233] in steels. The observed orientation relationship between f.c.c. austenite and cementite is determined by a crystallographic group–subgroup relationship between transformation participants and noncrystallographic symmetry which determines the transformation of triangulated clusters of transformation participants. Sequential fulfillment of diagonal flipping in the 15-vertex fragments of linear substructure (these fragments are equivalent by translation) ensures the austenite–cementite transformation in the whole infinite crystal. The energy barrier for diagonal flipping in the rhombus with iron atoms in its vertices has been calculated using the Morse interatomic potential and is found to be equal to 162 kJ mol−1 at the face-centered cubic–body-centered cubic transformation temperature in iron.

Structural, morphological, and magnetic study of nanocrystalline cobalt-copper powders synthesized by the polyol process

1995 ◽  
Vol 10 (6) ◽  
pp. 1546-1554 ◽  
Author(s):  
G.M. Chow ◽  
L.K. Kurihara ◽  
K.M. Kemner ◽  
P.E. Schoen ◽  
W.T. Elam ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Copper Powders ◽  
Face Centered ◽  
Increasing Temperature ◽  
X Ray Absorption

Nanocrystalline CoxCu100−x (4 ⋚ x ⋚ 49 at. %) powders were prepared by the reduction of metal acetates in a polyol. The structure of powders was characterized by x-ray diffraction (XRD), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), extended x-ray absorption fine structure (EXAFS) spectroscopy, solid-state nuclear magnetic resonance (NMR) spectroscopy, and vibrating sample magnetometry (VSM). As-synthesized powders were composites consisting of nanoscale crystallites of face-centered cubic (fcc) Cu and metastable face-centered cubic (fcc) Co. Complementary results of XRD, HRTEM, EXAFS, NMR, and VSM confirmed that there was no metastable alloying between Co and Cu. The NMR data also revealed that there was some hexagonal-closed-packed (hcp) Co in the samples. The powders were agglomerated, and consisted of aggregates of nanoscale crystallites of Co and Cu. Upon annealing, the powders with low Co contents showed an increase in both saturation magnetization and coercivity with increasing temperature. The results suggested that during preparation the nucleation of Cu occurred first, and the Cu crystallites served as nuclei for the formation of Co.

Preparation and Property of Al87Ce3Ni8.5Mn1.5 Nanophase Amorphous Composites

2011 ◽  
Vol 412 ◽  
pp. 263-266
Author(s):  
Hong Wei Zhang ◽  
Li Li Zhang ◽  
Feng Rui Zhai ◽  
Jia Jin Tian ◽  
Can Bang Zhang
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Single Phase ◽  
Volume Fraction ◽  
Material Structure ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Different Temperatures

The higher mechanical strength of Al87Ce3Ni8.5Mn1.5 nanophase amorphous composites has been obtained with two methods. The first nanophase amorphous composites are directly produced by the single roller spin quenching technology. The method taken for the second nanophase amorphous composites is at first to obtain amorphous single-phase alloy, followed by annealed at different temperatures .The formative condition, the microstructure, the particle size, the volume fraction of α-Al phase and microhardness of nanophase amorphous composites etc have been investigated and compared by X-ray diffraction (XRD) and transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The microstructure of composites produced by the second method is higher than the former, the fabricated material structure of the system is more uniform and the process is easier to control.

scholarly journals Lead-Free BNT–BT0.08/CoFe2O4 Core–Shell Nanostructures with Potential Multifunctional Applications

Nanomaterials ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 672
Author(s):  
Marin Cernea ◽  
Roxana Radu ◽  
Harvey Amorín ◽  
Simona Gabriela Greculeasa ◽  
Bogdan Stefan Vasile ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Molar Ratio ◽  
Transmission Electron Microscopy Data ◽  
Core Shell ◽  
Shell Nanoparticles ◽  
Two Phase ◽  
X Ray ◽  
Shell Nanostructures

Herein we report on novel multiferroic core–shell nanostructures of cobalt ferrite (CoFe2O4)–bismuth, sodium titanate doped with barium titanate (BNT–BT0.08), prepared by a two–step wet chemical procedure, using the sol–gel technique. The fraction of CoFe2O4 was varied from 1:0.5 to 1:1.5 = BNT–BT0.08/CoFe2O4 (molar ratio). X–ray diffraction confirmed the presence of both the spinel CoFe2O4 and the perovskite Bi0.5Na0.5TiO3 phases. Scanning electron microscopy analysis indicated that the diameter of the core–shell nanoparticles was between 15 and 40 nm. Transmission electron microscopy data showed two–phase composite nanostructures consisting of a BNT–BT0.08 core surrounded by a CoFe2O4 shell with an average thickness of 4–7 nm. Cole-Cole plots reveal the presence of grains and grain boundary effects in the BNT–BT0.08/CoFe2O4 composite. Moreover, the values of the dc conductivity were found to increase with the amount of CoFe2O4 semiconductive phase. Both X-ray photoelectron spectroscopy (XPS) and Mössbauer measurements have shown no change in the valence of the Fe3+, Co2+, Bi3+ and Ti4+ cations. This study provides a detailed insight into the magnetoelectric coupling of the multiferroic BNT–BT0.08/CoFe2O4 core–shell composite potentially suitable for magnetoelectric applications.

Controlling Aspect Ratio of Copper Group Nanowire Arrays by Electrochemical Deposition in the Nanopores of AAO

2011 ◽  
Vol 335-336 ◽  
pp. 429-432 ◽  
Author(s):  
Xiu Yu Sun ◽  
Fa Qiang Xu
Keyword(s):  
Aspect Ratio ◽  
Nanowire Arrays ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
X Ray ◽  
Anodic Aluminum ◽  
Au Nanowire ◽  
The Face ◽  
Face Centered ◽  
Xrd Patterns

Highly ordered Cu, Ag and Au nanowire arrays with high aspect ratio and highly dense self-supporting nanowire patterns of copper group were successfully prepared using cyclic voltammetry with the assistance of anodic aluminum oxide (AAO) template. The X-ray diffraction (XRD) patterns of the metal nanowries were indexed to the face-centered cubic structure. The field emission scanning electron microscope (FE-SEM) results demonstrated that the length of nanowire could be controlled by changing the electrodepositon conditions. The aspect ratio of nanowire arrays can be tuned.

Sign in / Sign up

Export Citation Format

Share Document