Structural, Magnetic, and Electrical Properties of BiFe1-xMnxO3 Thin Films

2009 ◽  
Vol 1199 ◽  
Author(s):  
Danilo G Barrionuevo ◽  
Surinder P Singh ◽  
Maharaj S. Tomar
Keyword(s):  
Thin Films ◽  
Room Temperature ◽  
Magnetic Measurements ◽  
Sol Gel ◽  
Ion Concentration ◽  
Ferromagnetic Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Si Substrates ◽  
Sol Gel Process

AbstractWe synthesized BiFe1-xMnxO3 (BFMO) for various compositions by sol gel process and thin films were deposited by spin coating on platinum Pt/Ti/SiO2/Si substrates. X-ray diffraction shows all the diffraction planes corresponding to rhombohedrally distorted perovskite BiFeO3 structure. The absence of any impurity phase in the films suggests the incorporation Mn ion preferentially to Fe site in the structure for low concentration. Magnetic measurements reveal the formation of ferromagnetic phase at room temperature with increased Mn substitution. On the other hand, ferroelectric polarization decreases with increasing Mn ion concentration. Raman studies suggest the dopant induced structural distortion.

Preparation of PST Ferroelectric Thin Films by Sol-Gel Process

2013 ◽  
Vol 734-737 ◽  
pp. 2328-2331
Author(s):  
Yu Fei You ◽  
C.H. Xu ◽  
Jing Zhe Wang ◽  
Jun Peng Wang
Keyword(s):  
Thin Films ◽  
Cross Section ◽  
Spin Coating ◽  
Room Temperature ◽  
Sol Gel ◽  
Ferroelectric Thin Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sol Gel Process ◽  
Electronic Microscope

Sol-gel method is used for the formation of Pb0.499Sr0.499TiO3 (PST)thin films. The initial films were prepared with spin coating sol solution on silicon wafer and drying at room temperature and then heating coated dry sol film at 400°C for 10min. This process was repeated for 1-4 times to obtain 4 initial films with different thicknesses. The 4 initial films were annealed at 700°C for 2h to obtain PST ceramics films. The morphologies of the surface and cross-section of PST films were observed with a scanning electronic microscope (SEM). The phase structures of PST films were analyzed using X-ray diffraction meter (XRD). Experimental results show that PST film prepared by coating sol on silicon with different thicknesses can be high smooth,uniform and compact film.

Effect of Annealing temperature on the Structural and Magnetic Properties of TbxY3-xFe5O12(x = 0.0, 1.0, 2.0) Thin Films Prepared by Sol-Gel Process

2012 ◽  
Vol 501 ◽  
pp. 236-241 ◽  
Author(s):  
Ftema W. Aldbea ◽  
Noor Bahyah Ibrahim ◽  
Mustafa Hj. Abdullah ◽  
Ramadan E. Shaiboub
Keyword(s):  
Thin Films ◽  
Magnetic Properties ◽  
Room Temperature ◽  
Annealing Temperature ◽  
Sol Gel ◽  
Vibrating Sample Magnetometer ◽  
X Ray ◽  
Garnet Phase ◽  
Sol Gel Process ◽  
Amorphous Structures

Thin films nanoparticles TbxY3-xFe5O12 (x=0.0, 1.0, 2.0) were prepared by the sol-gel process followed by annealing process at various annealing temperatures of 700° C, 800° C and 900° C in air for 2 h. The results obtained from X-ray diffractometer (XRD) show that the films annealed below 900°C exhibit peaks of garnet mixed with small amounts of YFeO3 and Fe2O3. Pure garnet phase has been detected in the films annealed at 900°C. Before annealing the films show amorphous structures. The particles sizes measurement using the field emission scanning electron microscope (FE-SEM) showed that the particles sizes increased as the annealing temperature increased. The magnetic properties were measured at room temperature using the vibrating sample magnetometer (VSM). The saturation magnetization (Ms) of the films also increased with the annealing temperature. However, different behavior of coercivity (Hc) has been observed as the annealing temperature was increased.

Sol-Gel derived Bi4-xNdxTi3O12 Thin Films and Their Characterization

2002 ◽  
Vol 737 ◽  
Author(s):  
R.E. Melgarejo ◽  
M.S. Tomar ◽  
A. Hidalgo ◽  
R.S. Katiyar
Keyword(s):  
Thin Films ◽  
Spin Coating ◽  
Bismuth Titanate ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Complete Solid Solution ◽  
Sol Gel Process ◽  
Ferroelectric Memory ◽  
Initial Results

ABSTRACTNd substituted bismuth titanate Bi4-xNdxTi3O12 were synthesized by sol-gel process and thin films were deposited on Pt substrate (Pt/TiO2/SiO2/Si) by spin coating. Thin films, characterized by X-ray diffraction and Raman spectroscopy, shows complete solid solution up to the composition x < 1. Initial results indicate that the ferroelectric polarization increases with increasing Nd content in the film with 2Pr = 50μC/cm2 for x = 0.46, which may have application in non-volatile ferroelectric memory devices.

Synthesis and Characterizations of Strontium Substituted Hydroxyapatite Thin Films

2010 ◽  
Vol 93-94 ◽  
pp. 231-234
Author(s):  
B. Hongthong ◽  
Satreerat K. Hodak ◽  
Sukkaneste Tungasmita
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Chemical Composition ◽  
Spin Coating ◽  
Phase Structure ◽  
Sol Gel ◽  
Cross Linking ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sol Gel Process

Strontium substituted hydroxyapatite(SrHAp) were fabricated both in the form of powder as reference and thin film by using inorganic precursor reaction. The sol-gel process has been used for the deposition of SrHAp layer on stainless steal 316L substrate by spin coating technique, after that the films were annealed in air at various temperatures. The chemical composition of SrHAp is represented (SrxCa1-x)5(PO4)3OH, where x is equal to 0, 0.5 and 1.0. Investigations of the phase structure of SrHAp were carried out by using X-ray diffraction technique (XRD). The results showed that strontium is incorporated into hydroxyapatite where its substitution for calcium increases in the lattice parameters, and Sr3(PO4)2 can be detected at 900°C. The SEM micrographs showed that SrHAp films exhibited porous structure before develop to a cross-linking structure.

Preparation of Titanium Oxide and Metal Titanates as Powders, Thin Films, and Microspheres by Novel Inorganic Sol-Gel Process

2005 ◽  
Vol 900 ◽  
Author(s):  
A. Deptuła ◽  
Kenneth C Goretta ◽  
Tadeusz Olczak ◽  
Wieslawa Lada ◽  
Andrzej G. Chmielewski ◽  
...  
Keyword(s):  
Thin Films ◽  
Ascorbic Acid ◽  
Nitric Acid ◽  
Titanium Oxide ◽  
Sol Gel ◽  
Solid State Reactions ◽  
X Ray Diffraction ◽  
Metal Hydroxides ◽  
X Ray ◽  
Sol Gel Process

ABSTRACTTitanium oxide and titanates based on Ba, Sr and Ca were prepared from commercial solutions of TiCl4 and HNO3. The main preparation steps for the sols consisted of elimination of chloride anions by distillation with nitric acid and addition of metal hydroxides for the titanates. Resulting sols were gelled and used to (1) prepare irregularly shaped powders by evaporation; (2) produce by a dipping technique thin films on glass, Ag, or Ti substrates; and (3) produce spherical powders (diameters <100 μm) by solvent extraction. Results of thermal and X-ray-diffraction analyses indicated that the temperatures required to form the various compounds were lower than those necessary to form the compounds by conventional solid-state reactions and comparable to those required with use of organometallic based sol-gel methods. Temperatures of formation could be further reduced by addition of ascorbic acid to the sols.

Reactive Sputtering Growth and Characterizations of InN Thin Films on Si Substrates

2012 ◽  
Vol 545 ◽  
pp. 290-293
Author(s):  
Maryam Amirhoseiny ◽  
Hassan Zainuriah ◽  
Ng Shashiong ◽  
Mohd Anas Ahmad
Keyword(s):  
Thin Films ◽  
Room Temperature ◽  
Rf Magnetron Sputtering ◽  
Rf Power ◽  
X Ray Diffraction ◽  
Nitrogen Gas ◽  
X Ray ◽  
Force Microscopy ◽  
Si Substrates ◽  
Atomic Force

We have studied the effects of deposition conditions on the crystal structure of InN films deposited on Si substrate. InN thin films have been deposited on Si(100) substrates by reactive radio frequency (RF) magnetron sputtering method with pure In target at room temperature. The nitrogen gas pressure, applied RF power and the distance between target and substrate were 2×10-2 Torr, 60 W and 8 cm, respectively. The effects of the Ar–N2 sputtering gas mixture on the structural properties of the films were investigated by using scanning electron microscope, energy-dispersive X-ray spectroscopy, atomic force microscopy and X-ray diffraction techniques.

Preparation of PZT Ferroelectric Thin Films by Sol-Gel Process

2012 ◽  
Vol 204-208 ◽  
pp. 4207-4210 ◽  
Author(s):  
Yu Fei You ◽  
C. H. Xu ◽  
Jun Peng Wang ◽  
Yu Liang Liu ◽  
Jin Feng Xiao ◽  
...  
Keyword(s):  
Thin Films ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Pzt Ceramics ◽  
X Ray ◽  
Pzt Film ◽  
Sol Gel Process ◽  
Pzt Films ◽  
Pzt Ferroelectric Thin Films ◽  
Electronic Microscope

Sol-gel method is used for the formation of Pb(Zr0.63Ti0.37)O3(PZT) thin films. The initial films were formed with spin coating sol solution on silicon wafer and drying coated wet sol film at 300°C for 5min. This process was repeated for 1-4 times to obtain 4 initial films with different thicknesses. 4 initial films were annealed at 500°C for 2h to obtain PZT ceramics films. The morphologies of the surface and cross-section of PZT films were observed with a scanning electronic microscope (SEM). The phase structures of PZT films were analyzed using an X-ray diffraction meter (XRD). Experimental results show that PZT film prepared by coating wet sol on silicon once can be high smooth and compact film.

Sol-gel derived Ba(Mg1/3Ta2/3)O3 thin films: Preparation and structure

1997 ◽  
Vol 12 (3) ◽  
pp. 596-599 ◽  
Author(s):  
Ji Zhou ◽  
Qing-Xin Su ◽  
K. M. Moulding ◽  
D. J. Barber
Keyword(s):  
Thin Films ◽  
Annealing Temperature ◽  
Volume Fraction ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Sol Gel Process ◽  
Small Grains

Ba(Mg1/3Ta2/3)O3 thin films were prepared by a sol-gel process involving the reaction of barium isopropoxide, tantalum ethoxide, and magnesium acetate in 2-methoxyethanol and subsequently hydrolysis, spin-coating, and heat treatment. Transmission electron microscopy, x-ray diffraction, and Raman spectroscopy were used for the characterization of the thin films. It was shown that the thin films tend to crystallize with small grains sized below 100 nm. Crystalline phase with cubic (disordered) perovskite structure was formed in the samples annealed at a very low temperature (below 500 °C), and well-crystallized thin films were obtained at 700 °C. Although disordered perovskite is dominant in the thin films annealed below 1000 °C, a low volume fraction of 1 : 2 ordering domains was found in the samples and grows with an increase of annealing temperature.

scholarly journals Synthesis & characterization of nanostructure VO2 thin film

2021 ◽  
Vol 2070 (1) ◽  
pp. 012098
Author(s):  
P K Ojha ◽  
S K Mishra
Keyword(s):  
Thin Films ◽  
Photoelectron Spectroscopy ◽  
Vanadium Dioxide ◽  
Sol Gel ◽  
Cost Effective ◽  
Metallic Phase ◽  
Strongly Correlated ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sol Gel Process

Abstract Vanadium dioxides are strongly correlated systems which undergo an insulator-metal transition (IMT) from a low-temperature semiconducting phase to a high-temperature metallic phase. Among them, Vanadium dioxide (VO2) undergoes IMT close to room temperature, accompanied by a structural transition resulting change of several orders of magnitude in the electrical and optical properties. Here, we present the synthesis of VO2 by sol-gel process which employs cost-effective precursors to synthesize pure phase of VO2 thin films. The synthesized thin films were characterized using an X-ray diffraction (XRD) to confirm phase purity and high resolution scanning electron microscope (HR-SEM) to study the crystallite and particle size for the synthesized films. The film’s surface was analyzed by X-ray photoelectron spectroscopy (XPS) to determine the valence state and chemical composition of vanadium dioxide.

FERROMAGNETISM IN Fe-DOPED ZnO THIN FILMS

2009 ◽  
Vol 23 (06) ◽  
pp. 815-824 ◽  
Author(s):  
R. B. ZHAO ◽  
D. L. HOU ◽  
Y. Y. WEI ◽  
Z. Z. ZHOU ◽  
C. F. PAN ◽  
...  
Keyword(s):  
Thin Films ◽  
Photoelectron Spectroscopy ◽  
Exchange Coupling ◽  
Room Temperature ◽  
Room Temperature Ferromagnetism ◽  
X Ray Diffraction ◽  
Axis Orientation ◽  
X Ray ◽  
Si Substrates ◽  
Fe Ions

Zn 1-x Fe x O (x = 0.04, 0.06, 0.08, 0.10, 0.12) thin films were grown on Si substrates using reactive magnetron sputtering. X-ray diffraction analyses show that the samples have wurtzite structures with the c-axis orientation. X-ray photoelectron spectroscopy results indicate that the Fe ions are in a +2 charge state in the films. Magnetization measurements indicate that room temperature ferromagnetism is present in films annealed in vacuum while films annealed in air were non-magnetic. The presence of oxygen vacancies in these films may mediate exchange coupling of the dopant ions, resulting in room temperature ferromagnetism.

Sign in / Sign up

Export Citation Format

Share Document