Supersaturated P-Type Polycrystaline Films Produced by Rapid Thermal Annealing of High Dose Boron Ion Implants for Interconnects and Shallow Junction Diffusion Sources

1990 ◽  
Vol 182 ◽  
Author(s):  
B. Raicu ◽  
M.I. Current ◽  
W.A. Keenan ◽  
D. Mordo ◽  
R. Brennan ◽  
...  
Keyword(s):  
Ion Implantation ◽  
Single Crystal ◽  
Thermal Annealing ◽  
Cross Section ◽  
Rapid Thermal Annealing ◽  
Single Crystal Silicon ◽  
High Dose ◽  
Crystal Silicon ◽  
Polysilicon Films ◽  
P Type

AbstractHighly conductive p+-polysilicon films were fabricated over Si(100) and SiO2 surfaces using high-dose ion implantation and rapid thermal annealing. Resistivities close to that of single crystal silicon were achieved. These films were characterized by a variety of electrical and optical techniques as well as SIMS and cross-section TEM.

Analysis of Silicon-On-Insulator Structures Formed By Oxygen Ion Implantation

1985 ◽  
Vol 43 ◽  
pp. 300-301
Author(s):  
N. Lewis ◽  
E. L. Hall ◽  
A. Mogro-Campero ◽  
R. P. Love
Keyword(s):  
Ion Implantation ◽  
Single Crystal ◽  
Single Crystal Silicon ◽  
Silicon Layer ◽  
Device Fabrication ◽  
Silicon On Insulator ◽  
High Dose ◽  
Crystal Silicon ◽  
Oxygen Ion ◽  
Oxygen Ion Implantation

The formation of buried oxide structures in single crystal silicon by high-dose oxygen ion implantation has received considerable attention recently for applications in advanced electronic device fabrication. This process is performed in a vacuum, and under the proper implantation conditions results in a silicon-on-insulator (SOI) structure with a top single crystal silicon layer on an amorphous silicon dioxide layer. The top Si layer has the same orientation as the silicon substrate. The quality of the outermost portion of the Si top layer is important in device fabrication since it either can be used directly to build devices, or epitaxial Si may be grown on this layer. Therefore, careful characterization of the results of the ion implantation process is essential.

scholarly journals Effect of Ion Implantation on the Adhesion of Positive Diazoquinone-Novolak Photoresist Films to Single-Crystal Silicon

2020 ◽  
Vol 14 (6) ◽  
pp. 1352-1357
Author(s):  
S. A. Vabishchevich ◽  
S. D. Brinkevich ◽  
V. S. Prosolovich ◽  
N. V. Vabishchevich ◽  
D. I. Brinkevich
Keyword(s):  
Ion Implantation ◽  
Single Crystal ◽  
Single Crystal Silicon ◽  
Crystal Silicon

Microheater Made of Heavily Boron Doped Single Crystal Silicon Beam

1992 ◽  
Vol 276 ◽  
Author(s):  
Mitsuteru Kimura ◽  
Kazuhiro Komatsuzaki
Keyword(s):  
Single Crystal ◽  
Single Crystal Silicon ◽  
Bridge Structure ◽  
Quick Response ◽  
Crystal Silicon ◽  
Etching Technique ◽  
Small Power ◽  
Boron Doped ◽  
Type Layer ◽  
P Type

ABSTRACTMicroheater made of heavily Boron doped single crystal Si beam covered with SiO2 film, 1000×300×3 μm, is fabricated on the n type Si substrate by the anisotropic etching technique. As this microheater has an air bridge structure of low resistivity semiconductor material with positive but small temperature coefficient of resistance, a broad heating area up to 800 °C is easily obtained and it has quick response with the thermal time constant t of about 4 ms and has small power consumption. Since this heating area is made of p type layer in the n type substrate,this area can be electrically isolated from the substrate because of the formation of p-n junction.

Formation of Buried Tisi2 Layers in Single Crystal Silicon by Ion Implantion

1987 ◽  
Vol 107 ◽  
Author(s):  
P. Madakson ◽  
G.J. Clark ◽  
F.K. Legoues ◽  
F.M. d'Heurle ◽  
J.E.E. Baglin
Keyword(s):  
Ion Implantation ◽  
Single Crystal ◽  
Room Temperature ◽  
Single Crystal Silicon ◽  
Crystal Silicon ◽  
Buried Layers

Buried TiSi2 layers, about 600Å thick and 900Å below the surface, were formed in < 111> silicon by ion implantation. The implantation was done with either 120 or 170 keV Ti+ to doses ranging from 5 x 1016 to 2 x 1017 ions/cm2, and at temperatures of between ambient and 650° C. Annealing was done at 600° C, 700°C and 1000°C. Continuous buried layers were achieved only with samples implanted with doses equal or greater than 1017 ions/cm2 and at temperatures above 450°C. Below this dose TiSi2, was present only as discrete precipitates. For room temperature implants, the TiSi2, layer is formed on the surface. The damage present consists of dispersed TiSi6 precipitates and microtwins.

A New Local Electronic Stopping Model for the Monte Carlo Simulation of Arsenic Ion Implantation into (100) Single-Crystal Silicon

1995 ◽  
Vol 389 ◽  
Author(s):  
S.-H. Yang ◽  
S. Morris ◽  
S. Tian ◽  
K. Parab ◽  
A. F. Tasch ◽  
...  
Keyword(s):  
Monte Carlo ◽  
Ion Implantation ◽  
Single Crystal ◽  
Density Functional ◽  
Single Crystal Silicon ◽  
Stopping Power ◽  
Crystal Silicon ◽  
Electronic Density ◽  
New Model ◽  
Electronic Stopping Power

ABSTRACTIn this paper is reported the development and implementation of a new local electronic stopping model for arsenic ion implantation into single-crystal silicon. Monte Carlo binary collision (MCBC) models are appropriate for studying channeling effects since it is possible to include the crystal structure in the simulators. One major inadequacy of existing MCBC codes is that the electronic stopping of implanted ions is not accurately and physically accounted for, although it is absolutely necessary for predicting the channeling tails of the profiles. In order to address this need, we have developed a new electronic stopping power model using a directionally dependent electronic density (to account for valence bonding) and an electronic stopping power based on the density functional approach. This new model has been implemented in the MCBC code, UT-MARLOWE The predictions of UT-MARLOWE with this new model are in very good agreement with experimentally-measured secondary ion mass spectroscopy (SIMS) profiles for both on-axis and off-axis arsenic implants in the energy range of 15-180 keV.

Semi-automatic, volume production of silicon solar cells

1987 ◽  
Vol 65 (8) ◽  
pp. 892-896 ◽  
Author(s):  
R. E. Thomas ◽  
C. E. Norman ◽  
S. Varma ◽  
G. Schwartz ◽  
E. M. Absi
Keyword(s):  
Solar Cells ◽  
Single Crystal ◽  
Plasma Etching ◽  
Low Cost ◽  
Single Crystal Silicon ◽  
High Yield ◽  
Silicon Solar Cells ◽  
Crystal Silicon ◽  
Volume Production ◽  
P Type

A low-cost, high-yield technology for producing single-crystal silicon solar cells at high volumes, and suitable for export to developing countries, is described. The process begins with 100 mm diameter as-sawn single-crystal p-type wafers with one primary flat. Processing steps include etching and surface texturization, gaseous-source diffusion, plasma etching, and contacting via screen printing. The necessary adaptations of such standard processes as diffusion and plasma etching to solar-cell production are detailed. New process developments include a high-throughput surface-texturization technique, and automatic printing and firing of cell contacts.The technology, coupled with automated equipment developed specifically for the purpose, results in solar cells with an average efficiency greater than 12%, a yield exceeding 95%, a tight statistical spread on parameters, and a wide tolerance to starting substrates (including the first 100 mm diameter wafers made in Canada). It is shown that with minor modifications, the present single shift 500 kWp (kilowatt peak) per year capacity technology can be readily expanded to 1 MWp per year, adapted to square and polycrystalline substrates, and efficiencies increased above 13%.

Sign in / Sign up

Export Citation Format

Share Document