Effects of Concurrent Co or Ti Silicidation on Transient Diffusion and End-of-Range Damage in Phosphorus Implanted Silicon

1992 ◽  
Vol 262 ◽  
Author(s):  
J.W. Honeycutt ◽  
J. Ravi ◽  
G. A. Rozgonyi
Keyword(s):  
Secondary Ion Mass Spectrometry ◽  
Complete Removal ◽  
Dislocation Loops ◽  
Enhanced Diffusion ◽  
Depth Profiles ◽  
Enhanced Dissolution ◽  
Implantation Damage ◽  
Transmission Electron ◽  
Defect Behavior ◽  
Secondary Ion

ABSTRACTThe effects of Ti and Co silicidation on P+ ion implantation damage in Si have been investigated. After silicidation of unannealed 40 keV, 2×1015 cm-2 P+ implanted junctions by rapid thermal annealing at 900°C for 10–300 seconds, secondary ion mass spectrometry depth profiles of phosphorus in suicided and non-silicided junctions were compared. While non-silicided and TiSi2 suicided junctions exhibited equal amounts of transient enhanced diffusion behavior, the junction depths under COSi2 were significantly shallower. End-of-range interstitial dislocation loops in the same suicided and non-silicided junctions were studied by planview transmission electron microscopy. The loops were found to be stable after 900°C, 5 minute annealing in non-silicided material, and their formation was only slightly effected by TiSi2 or COSi2 silicidation. However, enhanced dissolution of the loops was observed under both TiSi2 and COSi2, with essentially complete removal of the defects under COSi2 after 5 minutes at 900°C. The observed diffusion and defect behavior strongly suggest that implantation damage induced excess interstitial concentrations are significantly reduced by the formation and presence of COSi2, and to a lesser extent by TiSi2. The observed time-dependent defect removal under the suicide films suggests that vacancy injection and/or interstitial absorption by the suicide film continues long after the suicide chemical reaction is complete.

Phosphorus / Silicon Interstitial Annealing After Ion Implantation

2000 ◽  
Vol 610 ◽  
Author(s):  
P. H. Keys ◽  
R. Brindos ◽  
V. Krishnamoorthy ◽  
M. Puga-Lambers ◽  
K. S. Jones ◽  
...  
Keyword(s):  
Ion Implantation ◽  
Secondary Ion Mass Spectrometry ◽  
Extended Defects ◽  
Enhanced Diffusion ◽  
Transmission Electron ◽  
Initial Nucleation ◽  
Primary Damage ◽  
Dopant Atoms ◽  
Phosphorus Doped ◽  
Secondary Ion

AbstractThe release of interstitials from extended defects after ion implantation acts as a driving force behind transient enhanced diffusion (TED). Implantation of Si+ ions into regions of phosphorus-doped silicon provides experimental insight into the interaction of silicon interstitials and dopant atoms during primary damage annealing. The presence of phosphorus influences the morphology of secondary defects during initial nucleation. Transmission electron microscopy (TEM) is used to differentiate between defect types and quantify the interstitials trapped in extended defects. This analysis reveals that phosphorus results in a reduction of interstitials trapped in observable extended defects. The interstitial flux released from the implanted region is also affected by the phosphorus doping. This phenomenon is closely studied using secondary ion mass spectrometry (SIMS) to monitor diffusion enhancements of dopant layers. Shifts in diffused dopant profiles are correlated with the different morphologies of the extended defects and the decay of the silicon interstitial supersaturation. This correlation is used to understand the interaction of excess silicon interstitials with phosphorus atoms.

Damage Removal Processes in Ion Implanted, Rapidly Annealed GaAs

1985 ◽  
Vol 52 ◽  
Author(s):  
D. C. Jacobson ◽  
S. J. Pearton ◽  
R. Hull ◽  
J. M. Poate ◽  
J. S. Williams
Keyword(s):  
Carrier Mobility ◽  
Secondary Ion Mass Spectrometry ◽  
High Dose ◽  
Electrical Characteristics ◽  
Dislocation Loops ◽  
Transmission Electron ◽  
Capacitance Voltage ◽  
Lattice Damage ◽  
Removal Processes ◽  
Secondary Ion

ABSTRACTThe removal of lattice damage and consequent activation by rapid thermal annealing of implanted Si, Se, Zn and Be in GaAs was investigated by capacitance-voltage profiling, Hall measurements, transmission electron microscopy (TEM), secondary ion mass spectrometry and Rutherford backscattering. The lighter species show optimum electrical characteristics at lower annealing temperatures (˜850°C for Be, ˜950°C for Si) than the heavier species (˜900°C for Zn, ˜1000°C for Se), consistent with the amount of lattice damage remaining after annealing. TEM reveals the formation of high densities (107 cm−2) of dislocation loops after 800°C, 3s anneals of high dose (1×1015 cm−2) implanted GaAs, which are gradually reduced in density after higher temperatures anneals (˜1000°C). The remaining loops do not appear to effect the electrical activation or carrier mobility in the implanted layer, the latter being comparable to bulk values.

Effect of the oxidation of a silicide layer on dopant diffusion in the underlying silicon

1999 ◽  
Vol 568 ◽  
Author(s):  
L. Kappius ◽  
A. K. Tyagi ◽  
U. Breuer ◽  
H. L. Bay ◽  
S. Manti
Keyword(s):  
Mass Spectrometry ◽  
Molecular Beam ◽  
Secondary Ion Mass Spectrometry ◽  
Enhanced Diffusion ◽  
Depth Profiles ◽  
Silicide Layer ◽  
Before And After ◽  
Sb Doping ◽  
20 Nm ◽  
Secondary Ion

ABSTRACTWe have studied the influence of an epitaxial silicide layer on the diffusion of B and Sb in silicon. B and Sb doping superlattices have been grown by molecular beam epitaxy. They were then covered with a 20 nm thick CoSi2 layer. Test samples were also grown without silicide. Samples were oxidized at various temperatures ranging from 800°C to 1200°C for times that ensured sufficient broadening of the spikes. Another set of samples was annealed at the same times and temperatures in N2. Dopant depth profiles were measured before and after diffusion by secondary ion mass spectrometry (SIMS). At the test samples we observed thermal diffusion of B and Sb, oxidation enhanced diffusion of B and oxidation retarded diffusion of Sb, all in accordance with the literature. In contrast to this, oxidized silicide capped samples showed a retardation of B diffusion by a factor of 2 - 10 as compared to thermal diffusivity and an enhancement of Sb diffusion by a factor of 1 - 2.

Defects Related to Mixing Behavior of Highly Silicon-Doped GaAs/AlAs Superlatitices

1988 ◽  
Vol 144 ◽  
Author(s):  
N. D. Theodore ◽  
C. B. Carter ◽  
P. Mei ◽  
S. A. Schwarz ◽  
J. P. Harbison ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mass Spectrometry ◽  
Transmission Electron Microscopy ◽  
Secondary Ion Mass Spectrometry ◽  
Dislocation Loops ◽  
Silicon Doping ◽  
Transmission Electron ◽  
Mixing Behavior ◽  
Silicon Doped ◽  
Secondary Ion

ABSTRACTThe mixing of highly silicon-doped GaAs/AlAs superlattices as a result of annealing has been investigated by transmission electron microscopy and secondary ion mass spectrometry. As silicon doping-levels were raised in this study to 1019 cm−3 and 1020 cm−3 defects such as prismatic dislocation loops and Si-rich precipitates were observed to occur in the superlattices upon annealing. A correlation has been observed between the presence of particular defects and the inhibition of dopant-enhanced superlattice mixing.

scholarly journals In Situ Correlative Microscopy Combining Transmission Electron Microscopy and Secondary Ion Mass Spectrometry

2018 ◽  
Vol 24 (S1) ◽  
pp. 380-381 ◽  
Author(s):  
Santhana Eswara ◽  
Lluis Yedra ◽  
Alisa Pshenova ◽  
Varun Sarbada ◽  
Jean-Nicolas Audinot ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mass Spectrometry ◽  
Transmission Electron Microscopy ◽  
Secondary Ion Mass Spectrometry ◽  
Correlative Microscopy ◽  
Transmission Electron ◽  
Ion Mass Spectrometry ◽  
Secondary Ion

scholarly journals Изменение структуры и свойств приповерхностного слоя Si, имплантированного Zn, в зависимости от флюенса облучения ионами -=SUP=-132-=/SUP=-Xe-=SUP=-26+-=/SUP=- с энергией 167 МэВ

2019 ◽  
Vol 53 (3) ◽  
pp. 332
Author(s):  
В.В. Привезенцев ◽  
В.С. Куликаускас ◽  
В.А. Скуратов ◽  
О.С. Зилова ◽  
А.А. Бурмистров ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Zinc Oxide ◽  
Cross Section ◽  
Secondary Ion Mass Spectrometry ◽  
Sample Surface ◽  
Transmission Electron ◽  
Oxide Phases ◽  
Secondary Ion ◽  
Surface Pores ◽  
Scanning Electron

AbstractSingle-crystal n -Si(100) wafers are implanted with ^64Zn^+ ions with an energy of 50 keV and dose of 5 × 10^16 cm^–2. Then the samples are irradiated with ^132Xe^26+ ions with an energy of 167 MeV in the range of fluences from 1 × 10^12 to 5 × 10^14 cm^–2. The surface and cross section of the samples are visualized by scanning electron microscopy and transmission electron microscopy. The distribution of implanted Zn atoms is studied by time-of-flight secondary-ion mass spectrometry. After irradiation with Xe, surface pores and clusters consisting of a Zn–ZnO mixture are observed at the sample surface. In the amorphized subsurface Si layer, zinc and zinc-oxide phases are detected. After irradiation with Xe with a fluence of 5 × 10^14 cm^–2, no zinc or zinc-oxide clusters are detected in the samples by the methods used in the study.

scholarly journals Новый подход к анализу фазового состава углеродсодержащих материалов методом времяпролетной вторично-ионной масс-спектрометрии

2019 ◽  
Vol 45 (2) ◽  
pp. 50
Author(s):  
М.Н. Дроздов ◽  
Ю.Н. Дроздов ◽  
А.И. Охапкин ◽  
С.А. Краев ◽  
М.А. Лобаев
Keyword(s):  
Mass Spectra ◽  
Secondary Ion Mass Spectrometry ◽  
Simple Algorithm ◽  
Cluster Ions ◽  
Two Phase ◽  
Depth Profiles ◽  
Secondary Cluster ◽  
Phase Systems ◽  
Secondary Ion

AbstractNew possibilities offered by the method of secondary ion mass spectrometry (SIMS) for analysis of the phase composition of carbon-containing materials are considered. Differences are established between the mass spectra of three carbon phases: diamond, diamond-like carbon (DLC), and graphite. A simple algorithm for the quantitative determination of different phases in two-phase systems diamond–graphite and DLC–graphite is proposed that is based on the measurement of relative intensities of secondary cluster ions such as C_8/C_5 and CsC_8/CsC_4. It is shown that nonuniform depth profiles of various carbon phases are formed in diamond structures upon laser cutting and in DLC structures upon thermal annealing.

scholarly journals Measurements of the Diffusion of Iron and Carbon in Single Crystal NiAl using Ion Implantation and Secondary Ion Mass Spectrometry

1998 ◽  
Vol 527 ◽  
Author(s):  
R. J. Hanrahan ◽  
S. P. Withrow ◽  
M. Puga-Lambers
Keyword(s):  
Mass Spectrometry ◽  
Ion Implantation ◽  
Single Crystal ◽  
Secondary Ion Mass Spectrometry ◽  
Tracer Diffusion ◽  
Dynamic Strain ◽  
Enhanced Diffusion ◽  
Ion Mass Spectrometry ◽  
Impurity Elements ◽  
Secondary Ion

ABSTRACTClassical diffusion measurements in intermetallic compounds are often complicated by low diffusivities or low solubilities of the elements of interest. Using secondary ion mass spectrometry for measurements over a relatively shallow spatial range may be used to solve the problem of low diffusivity. In order to simultaneously obtain measurements on important impurity elements with low solubilities we have used ion implantation to supersaturate a narrow layer near the surface. Single crystal NiAl was implanted with either 12C or both 56Fe and 12C in order to investigate the measurement of substitutional (Fe) versus interstitial (C) tracer diffusion and the cross effect of both substitutional and interstitial diffusion. When C alone was implanted negligible diffusion was observed over the range of times and temperatures investigated. When both Fe and C were implanted together significantly enhanced diffusion of the C was observed, which is apparently associated with the movement of Fe. This supports one theory of dynamic strain aging in Fe alloyed NiAl.

Determination of the Distribution of Ion Implantation Boron in Silicon

2000 ◽  
Vol 650 ◽  
Author(s):  
Te-Sheng Wang ◽  
A.G. Cullis ◽  
E.J.H. Collart ◽  
A.J. Murrell ◽  
M.A. Foad
Keyword(s):  
Electron Microscopy ◽  
Secondary Ion Mass Spectrometry ◽  
Low Energy ◽  
Concentration Profiles ◽  
Impurity Profile ◽  
Transmission Electron ◽  
Device Applications ◽  
P Type ◽  
Secondary Ion

ABSTRACTBoron is the most important p-type dopant in Si and it is essential that, especially for low energy implantation, both as-implanted B distributions and those produced by annealing should be characterized in very great detail to obtain the required process control for advanced device applications. While secondary ion mass spectrometry (SIMS) is ordinarily employed for this purpose, in the present studies implant concentration profiles have been determined by direct B imaging with approximately nanometer depth and lateral resolution using energy-filtered imaging in the transmission electron microscopy. The as-implanted B impurity profile is correlated with theoretical expectations: differences with respect to the results of SIMS measurements are discussed. Changes in the B distribution and clustering that occur after annealing of the implanted layers are also described.

Sign in / Sign up

Export Citation Format

Share Document