Heating Rate Effects in Rapid Thermal Annealing of Arsenic Implanted Silicon

1994 ◽  
Vol 342 ◽  
Author(s):  
J.P. de Souza ◽  
P.F.P. Fichtner ◽  
D.K. Sadana
Keyword(s):  
Heating Rate ◽  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Solid Phase ◽  
Furnace Annealing ◽  
Residual Defect ◽  
Projected Range ◽  
Rate Effects ◽  
Amorphous Si ◽  
Heavy Dose

ABSTRACTCross section TEM and channeling analysis show that the heating rate (HR) of a rapid thermal annealing (RTA) cycle affects the residual defect distribution in Si implanted with As+ to a heavy dose (≈ 1016 cm−2). Two defect bands are observed after solid phase epitaxial growth (SPEG): the first one centered at a depth corresponding to the projected range of the As (band I), and the second one located at depth corresponding to the original amorphous crystalline (a-c) interface (band II). The density of defects in band I is found to increase with the As dose, and with the annealing temperature (550 - 650°C, furnace annealing). However, for RTA (800 - 1000°C) both the density and depth distribution of these defects are dependent on HR. We propose that Si self-interstitials (SiI) are created at the a-c interface when As becomes substitutional during SPEG. The SPEG velocity determines whether the SiI are accommodated in the amorphous Si layer (low velocities) or are captured by the regrowing c-Si (high velocities)

Uniform Poly-Si TFTs for AMOLEDs Using Field-Enhanced Rapid Thermal Annealing

2007 ◽  
Vol 124-126 ◽  
pp. 447-450 ◽  
Author(s):  
Hyoung June Kim
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Thin Film Transistors ◽  
Solid Phase ◽  
Radiative Heating ◽  
Solid Phase Crystallization ◽  
Glass Substrates ◽  
Grain Structures ◽  
Amorphous Si ◽  
Si Thin Film

Polycrystalline Si thin film transistors (TFTs) have been fabricated through solid phase crystallization using field-enhanced rapid thermal annealing (FE-RTA) system. The system consists of inline furnace modules for preheating and cooling of the glass substrates and a process module for rapid radiative heating combined with alternating magnetic field induction. The FE-RTA system enables crystallization of amorphous Si at high throughputs without any glass damages. While the typical grain structures of poly-Si by FE-RTA are similar to those of solid phase crystallization, the residual amorphous Si and intragranular defects are reduced.

Comparison Between Rapid Thermal and Furnace Annealing for A-Si Solid Phase Crystallization

1996 ◽  
Vol 424 ◽  
Author(s):  
Reece Kingi ◽  
Yaozu Wang ◽  
Stephen J. Fonash ◽  
Osama Awadelkarim ◽  
John Mehlhaff
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Annealing Temperature ◽  
Solid Phase ◽  
Growth Time ◽  
Crystallization Time ◽  
Solid Phase Crystallization ◽  
Furnace Annealing ◽  
Lower Growth ◽  
Transient Time

AbstractRapid thermal annealing and furnace annealing for the solid phase crystallization of amorphous silicon thin films deposited using PECVD from argon diluted silane have been compared. Results reveal that the crystallization time, the growth time, and the transient time are temperature activated, and that the resulting polycrystalline silicon grain size is inversely proportional to the annealing temperature, for both furnace annealing and rapid thermal annealing. In addition, rapid thermal annealing was found to result in a lower transient time, a lower growth time, a lower crystallization time, and smaller grain sizes than furnace annealing, for a given annealing temperature. Interestingly, the transient time, growth time, and crystallization time activation energies are much lower for rapid thermal annealing, compared to furnace annealing.We propose two models to explain the observed differences between rapid thermal annealing and furnace annealing.

Approaches to modifying solid phase crystallization kinetics for a-Si films

1996 ◽  
Vol 424 ◽  
Author(s):  
Reece Kingi ◽  
Yaozu Wang ◽  
Stephen Fonash ◽  
Osama Awadelkarim ◽  
Yuan-Mn Li
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Crystallization Kinetics ◽  
Solid Phase ◽  
Surface Treatments ◽  
Film Deposition ◽  
Crystallization Time ◽  
Solid Phase Crystallization ◽  
Furnace Annealing ◽  
Thermal Budget

AbstractThree approaches to modifying the solid phase crystallization kinetics of amorphous silicon thin films are examined with the goal of reducing the thermal budget and improving the poly-Si quality for thin film transistor applications. The three approaches consist of (1) variations in the PECVD a-Si deposition parameters; (2) the application of pre-fumace-anneal surface treatments; and (3) using both rapid thermal annealing and furnace annealing at different temperatures. We also examine the synergism among these approaches.Results reveal that (1) film deposition dilution and dilution/temperature changes do not strongly affect crystallization time, but do affect grain size; (2) pre-anneal surface treatments can dramatically reduce the solid phase crystallization thermal budget for diluted films and act synergistically with deposition dilution or dilution/temperature effects; and (3) rapid thermal annealing leads to different crystallization kinetics from that seen for furnace annealing.

Epitaxial Growth of Near Noble Silicides on (111)Si by Rapid Thermal Annealing

1986 ◽  
Vol 74 ◽  
Author(s):  
H. C. Cheng ◽  
I. C. Wu ◽  
L. J. Chen
Keyword(s):  
Epitaxial Growth ◽  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Solid Phase ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
Furnace Annealing ◽  
Transmission Electron ◽  
Vacuum Method ◽  
Comparable Quality

AbstractThe epitaxial growth of near noble silicides, including CoSi2, NiSi2, FeSi2, Pd2 Si, and PtSi on (111)Si, by rapid thermal annealing was studied by transmission electron microscopy. Single-crystalline CoSi2 was formed on (111)Si in the solid phase epitaxy regime by a non-ultra-high vacuum method. The effect on gas ambient was found to be of critical importance on the growth of single-crystal CoSi2 on (111)Si. The best NiSi2, FeSi2, Pd2 Si, and PtSi epitaxy grown on (111)Si by rapid thermal annealing were found to be of comparable quality to those grown by conventional furnace annealing.

Steady-State Versus Rapid Thermal Annealing of Phosphorusimplanted Pseudomorphic Si(100)/Ge0.12Si0.88

1994 ◽  
Vol 342 ◽  
Author(s):  
D. Y. C. Lie ◽  
J. H. Song ◽  
N. D. Theodore ◽  
F. Eisen ◽  
M.-A. Nicolet ◽  
...  
Keyword(s):  
Steady State ◽  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Room Temperature ◽  
Molecular Beam ◽  
Strain Relaxation ◽  
Furnace Annealing ◽  
Dopant Activation ◽  
X Ray ◽  
Projected Range

ABSTRACTPseudomorphic Ge0.12Si0.88 films 265 nm thick grown by molecular beam epitaxy on p- Si(100) substrates were implanted with 100 keV 31P at room temperature for a dose of 5 x 1013/cm2. The projected range of the implanted P is about half the epilayer thickness. The implanted layers, together with non-implanted virgin samples, were subsequently annealed by both rapid thermal annealing in nitrogen and by steady-state furnace annealing in vacuum. The damage and strain of the annealed layers were studied by 4He channeling and x-ray doublecrystal diffraction. For a dose of 5 x 1013 P /cm2, both the damage and strain introduced by implantation can be completely removed, within instrumental sensitivity, by rapid thermal annealing at 700 °C for 10 - 40 s. Furnace annealing at 550 °C for 30 min for this sample removes most of the damage and strain induced by implantation. Furnace annealing at 700 °C or higher worsens the crystallinity of the layer and the strain relaxes. Hall measurements were performed on the same samples. Furnace annealing cannot achieve good dopant activation without introducing significant strain relaxation to the heterostructure, while rapid thermal annealing can.

Ultra-Shallow Junctions by Ion Implantation and Rapid Thermal Annealing: Spike-Anneals, Ramp Rate Effects

1999 ◽  
Vol 568 ◽  
Author(s):  
Aditya Agarwal ◽  
Hans-J. Gossmann ◽  
Anthony T. Fiory
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Driving Forces ◽  
Recent Experimental Data ◽  
Enhanced Diffusion ◽  
Temperature Ramp ◽  
Rate Effects ◽  
Low Energies ◽  
Ultra Shallow Junctions ◽  
P Type

ABSTRACTOver the last couple of years rapid thermal annealing (RTA) equipment suppliers have been aggressively developing lamp-based furnaces capable of achieving ramp-up rates on the order of hundreds of degrees per second. One of the driving forces for adopting such a strategy was the experimental demonstration of 30nm p-type junctions by employing a ramp-up rate of ≈400°C/s. It was subsequently proposed that the ultra-fast temperature ramp-up was suppressing transient enhanced diffusion (TED) of boron which results from the interaction of the implantation damage with the dopant. The capability to achieve very high temperature ramp-rates was thus embraced as an essential requirement of the next generation of RTA equipment.In this paper, recent experimental data examining the effect of the ramp-up rate during spike-and soak-anneals on enhanced diffusion and shallow junction formation is reviewed. The advantage of increasing the ramp-up rate is found to be largest for the shallowest, 0.5-keV, B implants. At such ultra-low energies (ULE) the advantage arises from a reduction of the total thermal budget. Simulations reveal that a point of diminishing return is quickly reached when increasing the ramp-up rate since the ramp-down rate is in practice limited. At energies where TED dominates, a high ramp-up rate is only effective in minimizing diffusion if the implanted dose is sufficiently small so that the TED can be run out during the ramp-up portion of the anneal; for larger doses, a high ramp-up rate only serves to postpone the TED to the ramp-down duration of the anneal. However, even when TED is minimized at higher implant energies via high ramp-up rates, the advantage is unobservable due to the rather large as-implanted depth. It appears then that while spike anneals allow the activation of ULE-implanted dopants to be maximized while minimizing their diffusion the limitation imposed by the ramp-down rate compromises the advantage of very aggressive ramp-up rates.

STRUCTURAL CHARACTERISTICS OF (Ba,Sr)TiO3 THIN FILMS BY RAPID THERMAL ANNEALING

2007 ◽  
Vol 14 (01) ◽  
pp. 141-145
Author(s):  
Q. Y. ZHANG ◽  
S. W. JIANG ◽  
Y. R. LI
Keyword(s):  
Thin Films ◽  
Grain Size ◽  
Heating Rate ◽  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Rapid Heating ◽  
Structural Characteristics ◽  
High Heating Rate ◽  
Duration Time ◽  
Temperature Heating

The rapid thermal annealing (RTA) process was adapted to crystallize the amorphous ( Ba,Sr ) TiO 3 thin films prepared on Si (111) substrates by RF magnetic sputtering deposition. The effect of annealing temperature, heating rate and duration time on crystallization was studied through X-ray diffraction and atomic force microscopy. The result shows that the crystallinity and grain size were strongly dependent on the temperature, heating rate, and duration time. Higher heating rate leads to smaller grain size. In high heating rate, the grain size shows different dependence of temperature from that of low heating rate. For a heating rate of 50°C/s, the grain size decreased with temperature increasing below 700°C, while after that temperature, the grain size increased slightly with the temperature increasing. At a certain temperature, the crystallinity and surface roughness improved with increase in annealing time, while grain size changed little. The effect of rapid heating rate on the nucleation and grain growth has been discussed, which contributes to the limited grain size of the annealed ( Ba,Sr ) TiO 3 thin films.

scholarly journals Synthesis of Ge1−xSnx Alloy Thin Films by Rapid Thermal Annealing of Sputtered Ge/Sn/Ge Layers on Si Substrates

Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2248 ◽  
Author(s):  
Hadi Mahmodi ◽  
Md Hashim ◽  
Tetsuo Soga ◽  
Salman Alrokayan ◽  
Haseeb Khan ◽  
...  
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Near Infrared ◽  
Annealing Temperature ◽  
Solid Phase ◽  
Infrared Region ◽  
Alloy Formation ◽  
Phase Mixing ◽  
Si Substrates ◽  
Msm Photodetector

In this work, nanocrystalline Ge1−xSnx alloy formation from a rapid thermal annealed Ge/Sn/Ge multilayer has been presented. The multilayer was magnetron sputtered onto the Silicon substrate. This was followed by annealing the layers by rapid thermal annealing, at temperatures of 300 °C, 350 °C, 400 °C, and 450 °C, for 10 s. Then, the effect of thermal annealing on the morphological, structural, and optical characteristics of the synthesized Ge1−xSnx alloys were investigated. The nanocrystalline Ge1−xSnx formation was revealed by high-resolution X-ray diffraction (HR-XRD) measurements, which showed the orientation of (111). Raman results showed that phonon intensities of the Ge-Ge vibrations were improved with an increase in the annealing temperature. The results evidently showed that raising the annealing temperature led to improvements in the crystalline quality of the layers. It was demonstrated that Ge-Sn solid-phase mixing had occurred at a low temperature of 400 °C, which led to the creation of a Ge1−xSnx alloy. In addition, spectral photo-responsivity of a fabricated Ge1−xSnx metal-semiconductor-metal (MSM) photodetector exhibited its extending wavelength into the near-infrared region (820 nm).

omparisons of Silicide Formation by Rapid Thermal Annealing and Conventional Furnace Annealing

1987 ◽  
Vol 92 ◽  
Author(s):  
E. Ma ◽  
M. Natan ◽  
B.S. Lim ◽  
M-A. Nicolet
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Silicide Formation ◽  
X Ray Diffraction ◽  
Furnace Annealing ◽  
Cross Sectional ◽  
Conventional Furnace ◽  
Diffusion Controlled ◽  
Conventional Furnace Annealing ◽  
Kinetics Of

ABSTRACTSilicide formation induced by rapid thermal annealing (RTA) and conventional furnace annealing (CFA) in bilayers of sequentially deposited films of amorphous silicon and polycrystalline Co or Ni is studied with RBS, X-ray diffraction and TEM. Particular attention is paid to the reliability of the RTA temperature measurements in the study of the growth kinetics of the first interfacial compound, Co2Si and Ni2Si, for both RTA and CFA. It is found that the same diffusion-controlled kinetics applies for the silicide formation by RTA in argon and CFA in vacuum with a common activation energy of 2.1+0.2eV for Co2Si and 1.3+0.2eV for Ni Si. Co and Ni atoms are the dominant diffusing species; during silicide formation by both RTA and CFA. The microstructures of the Ni-silicide formed by the two annealing techniques, however, differs considerably from each other, as revealed by cross-sectional TEM studies.

Sign in / Sign up

Export Citation Format

Share Document