A Study on The Phase Transformation and Exchange-Coupling of (Nd0 95La0 05)9 5FebalCo5Nb2B10.5 Nanocomposites

1999 ◽  
Vol 577 ◽  
Author(s):  
Q. Chen ◽  
B. M. Ma ◽  
B. Lu ◽  
M. Q. Huang ◽  
D. E. Laughlin
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Phase Transformation ◽  
Thermal Treatment ◽  
Grain Growth ◽  
Exchange Coupling ◽  
Phase Distribution ◽  
Maximum Energy ◽  
Treatment Temperature ◽  
Phase Identification

ABSTRACTThe phase transformation and the exchange coupling in (Ndo095Lao005)9.5FebaICOsNb 2BI05 have been investigated. Nanocomposites were obtained by treating amorphous precursors at temperatures ranging from 650TC to 9500C for 10 minutes. The magnetic properties were characterized via the vibrating sample magnetometer (VSM). X-ray diffraction (XRD), thermomagnetic analysis (TMA), and transmission electron microscopy (TEM) were used to perform phase identification, measure grain size, and analyze phase distribution. The strength of the exchange coupling between the magnetically hard and soft phases in the corresponding nanocomposite was analyzed via the AM-versus-H plot. It was found that the remanence (Br), coercivity (Hci), and maximum energy product (BHmax) obtained were affected by the magnetic phases present as well as the grain size of constituent phases and their distribution. The optimal magnetic performance, BHm, occurred between 700°C to 750°C, where the crystallization has completed without excessive grain growth. TMA and TEM indicated that the system was composed of three phases at this point, Nd2(Fe Co) 14B, ca-Fe, and Fe3B. The exchange coupling interaction among these phases was consistently described via the AM-versus-H plot up to 750°C. The Br, Hci, and BHmax degraded severely when the thermal treatment temperature increased from 750°C. This degradation may be attributed to the grain growth of the main phases, from 45 to 68nm, and the development of precipitates, which grew from 5nm at 750°C to 12nm at 850°C. Moreover, the amount of the precipitates was found to increase with the thermal treatment temperatures. The precipitates, presumably borides, may cause a decrease in the amount of the a-Fe and Fe 3B and result in a redistribution of the Co in the nanocomposites. The increase of the Co content in the Nd 2(Fe Co) 14B may explain the increase of its Curie temperature with the thermal treatment temperatures. In this paper, we examine the impacts of these factors on the magnetic properties of (Ndo 95Lao 05)9 5FebaICosNb2B10.5 nanocomposite.

EFFECT OF COPPER OXIDE ON THE GRAIN GROWTH AND INITIAL PERMEABILITY OF Mg–Cu–Zn FERRITES

2010 ◽  
Vol 24 (02) ◽  
pp. 169-182
Author(s):  
M. MANJURUL HAQUE ◽  
M. HUQ ◽  
SYED FARID UDDIN FARHAD ◽  
JASIM UDDIN KHAN ◽  
M. A. HAKIM
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Grain Growth ◽  
Spinel Phase ◽  
Initial Permeability ◽  
Cu Content ◽  
Average Grain Size ◽  
Zn Ferrite ◽  
Effect Of Copper ◽  
Microstructure And Magnetic Properties

The microstructure and magnetic properties of Mg – Cu – Zn ferrites prepared by using solid-state reaction method have been investigated. X-ray diffraction (XRD), a scanning electron microscope (SEM), impedance analyzer and a vibrating sample magnetometer (VSM) were utilized in order to study the effect of copper substitution and its impact on the crystal structure, grain size, microstructure and magnetic properties of the Mg – Cu – Zn ferrite. The formation of cubic spinel phase was identified using XRD technique. The microstructures of the samples show that the grain growth is greatly enhanced by the addition of CuO which is attributed to the liquid phase during sintering. The average grain size (Dm) increases significantly with increasing Cu content. The initial permeability (μ') of the samples increases appreciably with increasing Cu content which is attributed to the increase of grain size and density of the samples. The resonance frequency (fr) of the samples shifts toward the lower frequency as the Cu content increases. The sharp fall of μ' in μ'-T curves is observed for all the samples which indicate the homogeneity of the samples. The saturation magnetization (Ms) of the Mg – Cu – Zn ferrites increases slightly with increasing Cu concentration.

scholarly journals Nanocrystalline Nd-Fe-B Alloys for Polymer-Bonded Magnets Production

2012 ◽  
Vol 2012 ◽  
pp. 1-6
Author(s):  
Aleksandar Grujić ◽  
Vladan Ćosović ◽  
Aleksandar Ćosović ◽  
Jasna Stajić-Trošić
Keyword(s):  
Magnetic Properties ◽  
Exchange Coupling ◽  
Magnetic Phase ◽  
Coupling Effect ◽  
Maximum Energy ◽  
Soft Magnetic ◽  
Nanocomposite Structure ◽  
Maximum Energy Product ◽  
Energy Product ◽  
Composite Production

This study presents how different nanostructures of starting Nd-Fe-B particles have influence on magnetic properties of polymer-bonded Nd-Fe-B materials. Two types of nanocrystalline Nd-Fe-B alloys were used for polymer composite production by compression molding technique. The particles with low neodymium content (Nd-low) have nanocomposite structure with small exchange coupling effect between hard and soft magnetic phase. In other hand, practically monophase hard magnetic structure of Nd-Fe-B particles with stoichiometric neodymium content (Nd-stoich) shows improved magnetic properties. With increasing concentration of polymer matrix, the coercivity (Hcb), remanence (Br), and maximum energy product ((BH)max) decrease more prominenty for composites with stoichiometric Nd-Fe-B content.

UFG to NC FePd by Combined Reaction Transformation Mode of Severely Plastically Deformed Disordered FePd

2006 ◽  
Vol 980 ◽  
Author(s):  
Vincent Sokalski ◽  
Andreas Kulovits ◽  
Jorg Wiezorek
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Phase Transformation ◽  
Cold Rolling ◽  
Grain Refinement ◽  
Magnetization Curve ◽  
Deformation Process ◽  
Intermetallic Alloys ◽  
Fine Grained ◽  
Angular Pressing

AbstractNumerous studies have shown that equiaxed ultra fine grained FePd alloys can be produced by phase transformation of heavily deformed austenitic FePd via the combined reaction mode. As the magnetic properties can be improved by suppression of the polytwinned micro-constituent formed by the conventional ordering mode it appears reasonable to speculate that further grain refinement might lead to further enhancement. In order to reduce the grain size in bulk intermetallic alloys severely plastically deformed austenitic FePd has been phase transformed in this study. Equal channel angular pressing (ECAP) has been used to deform disordered FePd. The microstructure and property evolution during the deformation process and post-deformation annealing have been studied using SEM, TEM and hardness and magnetization curve measurements. The observations are compared to known results from use of other deformation processing routes, such as cold rolling.

Influence of Milling Time on Magnetic Properties and Microstructure of Sintered Nd-Fe-B Based Permanent Magnets

2018 ◽  
Vol 930 ◽  
pp. 445-448
Author(s):  
R.G.T. Fim ◽  
M.R.M. Silva ◽  
S.C. Silva ◽  
Julio Cesar Serafim Casini ◽  
P.A.P. Wendhausen ◽  
...  
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Permanent Magnets ◽  
Milling Time ◽  
Maximum Energy ◽  
Inhomogeneous Distribution ◽  
Maximum Energy Product ◽  
Grain Sizes ◽  
Energy Product

In this paper, the effect of the grain size on sintered Nd-Fe-B based permanent magnets was investigated. In order, the magnets were produced by different milling times at 200 rpm and then vacuum sintered at 1373 K for 60 minutes followed by cooling outside the furnace. The magnets either produced by lower and higher milling times (30 and 75 minutes) exhibited lower remanence and coercivity, due the inhomogeneous distribution of the grain sizes. The magnet produced by intermediary milling time (45 minutes) exhibited the highest properties among all samples, with remanence of 1.06 T, coercivity of 891.3 KA.m-1, maximum energy product of 211 KJ.m3and a squareness factor equal 0.92.

Influence of Thermal Treatment Temperature on Phase Formation and Bioactivity of Glass-Ceramics Based on the SiO2-Na2O-CaO-P2O5 System

2019 ◽  
Vol 798 ◽  
pp. 229-234 ◽  
Author(s):  
Puripat Kantha ◽  
Naris Barnthip ◽  
Kamonpan Pengpat ◽  
Tawee Tunkasiri ◽  
Nuttapon Pisitpipathsin
Keyword(s):  
Heat Treatment ◽  
Thermal Treatment ◽  
Phase Formation ◽  
Raw Materials ◽  
Glass Ceramics ◽  
Treatment Temperature ◽  
Phase Identification ◽  
X Ray Diffraction ◽  
Thermal Treatment Temperature ◽  
45S5 Glass

In this work, the thermal treatment temperature effect on phase formation and bioactivity of glass-ceramics based on the SiO2-Na2O-CaO-P2O5 system has been studied. The chemical composition of the system is 45 wt.% SiO2, 24.5 wt.% Na2O, 24.5 wt.% CaO and 6 wt.% P2O5 (45S5). The rice husk ash is used as the natural raw materials instead of commercial SiO2. All of the investigated compositions were prepared by melting the glass mixtures at 1350°C for 3 h. The resulting glass samples were heated at different thermal treatment temperatures ranging from 750 to 1050°C with fixed dwell-time for 4 h for crystallization. Phase identification of the 45S5 glass ceramics was carried out by X-Ray diffraction (XRD). Moreover, the physical properties such as density, porosity and mechanical properties were systematically investigated. It was found that, the increasing of heat treatment temperature led to the increasing of the Na2Ca2Si3O9 phase and obtaining better bioactive behavior after incubation of glass-ceramics in simulated body fluid (SBF) for 7 days. The maximum hardness value of 4.02 GPa was achieved after heating at 1050°C for 4 h. However, the density value has slightly changed with various heat treatment temperatures.

scholarly journals Structure and Properties of Nd-Fe-B Alloy Subjected to HDDR Process

2016 ◽  
Vol 61 (1) ◽  
pp. 217-220 ◽  
Author(s):  
M. Szymański ◽  
B. Michalski ◽  
M. Leonowicz ◽  
Z. Miazga
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Phase Transformation ◽  
Grain Boundaries ◽  
Master Alloy ◽  
Structure And Properties ◽  
Rich Phase ◽  
Average Grain Size ◽  
Reversal Phase ◽  
Neodymium Magnets

In this paper the Hydrogenation, Disproportionation, Desorption and Recombination (HDDR) route was tested, for the Nd-Fe-B master alloy, as a prospective procedure for recycling of sintered scrap neodymium magnets. The HDDR method is based on the hydrogen induced reversal phase transformation of Nd-Fe-B alloy: Nd2Fe14B + (2±x) H2 = 2NdH2±x + Fe2B + 12Fe. Microstructural observations (SEM), phase constitution studies (XRD) and measurement of magnetic properties (VSM) were done to investigate the HDDR transformation progress. It was observed that disproportionation reaction starts at the grain boundaries, where the Nd-rich phase is located. Average grain size was reduced and coercive material was produced as a result of the HDDR process. Obtained results are similar to literature data.

Recrystallisation, Grain Growth and Texture Evolution in Nonoriented Electrical Steels

2007 ◽  
Vol 558-559 ◽  
pp. 657-664 ◽  
Author(s):  
Jong Tae Park ◽  
Jae Kwan Kim ◽  
Jerzy A. Szpunar
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Grain Growth ◽  
Texture Evolution ◽  
Size Control ◽  
Goss Texture ◽  
Final Annealing ◽  
Electrical Steels ◽  
Grain Size Control ◽  
Specific Orientation

The magnetic properties of nonoriented electrical steels are influenced by grain size and texture of final products. The key technology in the commercial production of nonoriented electrical steels is to grow grains with {hk0}<001> texture up to the optimum size in the final annealing process. The problems related to grain size control have been extensively investigated, while texture control has received much less attention. Therefore, there is enough room to improve the magnetic properties through the control of texture. In this study, systematic investigations on the texture evolution during both recrystallization and grain growth have been made. The formation of recrystallization texture is explained by oriented nucleation. This is supported by the fact that the area fraction of nuclei or recrystallized grains with specific orientation to all new grains remains almost constant during the progress of recrystallization. Most nuclei have a high misorientation angle of 25∼55° with the surrounding deformed matrices. During the progress of grain growth, the Goss texture component continues to decrease because the Goss grains have a high percentage of low angle, low mobility grain boundaries. The grains of Goss orientation have a smaller grain size than those of random orientation.

scholarly journals Study of Structure and Magnetic Properties of SmCo10 Alloy Prepared by Different Methods

2018 ◽  
Vol 2018 ◽  
pp. 1-10
Author(s):  
Xiang Chi ◽  
Ying Li ◽  
De-quan Er ◽  
Xu-hao Han ◽  
Xiu-li Duan ◽  
...  
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Grain Boundaries ◽  
Melt Spinning ◽  
Phase Distribution ◽  
Cast Alloy ◽  
Structural Parameters ◽  
Homogeneous Distribution ◽  
Annealed Alloy ◽  
Average Grain Size

In this paper, the phase compositions, microstructures, atomic structures, and magnetic properties of Co-rich SmCo10 alloys prepared by arc-melting, annealing, and melt-spinning were studied. It was found that as-cast alloy is composed of Th2Zn17-type Sm2Co17 matrix with an average grain size of ∼45 μm accompanied by lamellar eutecticum (consisting of α-Co and Th2Zn17-type Sm2Co17) distributed at grain boundaries. The annealed alloy has the same phase composition and phase distribution as the as-cast alloy except that the average grain size decreases to ∼35 μm, and the eutecticum has more homogeneous distribution on the matrix. Simultaneously, the atomic structure of Sm2Co17 is unchanged with only a decrease in structural disorder after annealing. The as-spun ribbons are composed of ∼95.5 vol.% TbCu7-type Sm2Co17 and the rest α-Co. The short rod-shaped α-Co grains are intermittently distributed at the grain boundaries of equiaxed Sm2Co17 grains. The as-spun ribbons show a higher coercivity, and the annealed alloy shows maximum magnetization. The structural parameters were calculated by Extended X-ray Absorption Fine Structure (EXAFS), and the relationship between structure and magnetic properties was discussed in detail.

Texture Development during Final Annealing in Nonoriented Electrical Steels

2005 ◽  
Vol 495-497 ◽  
pp. 471-476 ◽  
Author(s):  
Jong Tae Park ◽  
Jerzy A. Szpunar ◽  
Jae Kwan Kim
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Grain Growth ◽  
Recrystallization Texture ◽  
Core Loss ◽  
Size Control ◽  
Final Annealing ◽  
Electrical Steels ◽  
Texture Change ◽  
Grain Size Control

Nonoriented electrical steels have been widely used as core materials in motors and generators. For these applications low core loss and high permeability are required. The magnetic properties of these steels depend on the grain size and crystallographic texture of the annealed final products. The problems related to grain size control have been extensively investigated, while texture control has received much less attention. The technologies used to control the grain size in nonoriented electrical steels have approached to their limits. However, there is still some possibility for improvement of the magnetic properties through texture control. In order to explore this possibility, the evolution of recrystallization texture for nonoriented electrical steels with 2% Si was systematically studied. Texture change during grain growth was additionally analyzed. The formation of recrystallization texture is explained by oriented nucleation. This is supported by the fact that the area fraction of nuclei or recrystallized grains with specific orientation to all new grains remains almost constant during the progress of recrystallization. Most nuclei have a high misorientation angle of 25~55° with the surrounding deformed matrices. During the progress of grain growth, Goss and {111}<112> components are weakened and the random texture is strengthened. The grains of the Goss and {111}<112> orientations have smaller grain size than those of random orientation.

Texture Change during Grain Growth in Non-Oriented Electrical Steel

2012 ◽  
Vol 715-716 ◽  
pp. 33-40 ◽  
Author(s):  
Y. Arita ◽  
L. Chan ◽  
S.D. Sintay ◽  
Anthony D. Rollett
Keyword(s):  
Computer Simulation ◽  
Grain Size ◽  
Magnetic Properties ◽  
Cold Rolling ◽  
Grain Growth ◽  
Electrical Steel ◽  
Experimental Result ◽  
New Approach ◽  
Texture Change ◽  
Texture Sample

Grain size and texture are very important for controlling the magnetic properties in non-oriented electrical steel. Grain size and texture are closely related because the texture usually changes during grain growth. In this study, texture changes with grain growth in non-oriented electrical steel are investigated. Two kinds of materials, Sample A and Sample B, were prepared in order to study the differences of the texture. Sample A, Fe-0.5wt%Si, is not annealed before cold rolling. Sample B, the same chemical composition as Sample A, is annealed before cold rolling. In Sample A, the {111} texture component increases markedly during grain growth. By contrast, in Sample B, the increase in {111} is less pronounced. The recrystallized orientations in both Samples are analyzed, and computer simulation is used to attempt to explain the texture changes during grain growth. In the case of Sample A, the simulations reproduce the experimental result well; for Sample B, however, the simulations do not agree as well. The microstructures before annealing exhibit strong alignment of the orientations, which will require a new approach to building the digital microstructures for instantiation of the simulations.

Sign in / Sign up

Export Citation Format

Share Document