HR-TEM Studies of FePt Nanoparticles by Exit Wave Reconstruction

2007 ◽  
Vol 998 ◽  
Author(s):  
Daniela Sudfeld ◽  
Olga Dmitrieva ◽  
Nina Friedenberger ◽  
Guenter Dumpich ◽  
Michael Farle ◽  
...  
Keyword(s):  
Data Storage ◽  
Density Functional ◽  
Lattice Structure ◽  
Magnetic Behavior ◽  
Magnetic Data ◽  
Fept Nanoparticles ◽  
Face Centered Cubic ◽  
Scattered Electron ◽  
Transmission Electron ◽  
Face Centered

ABSTRACTFePt nanoparticles are promising materials for high-density magnetic data storage media [1] and bio-medical applications such as drug-targeting and hyperthermia [2]. To understand their magnetic properties [3] it is essential to get insights into the lattice structure of isolated nanoparticles which influence the magnetic behavior.Typically, lattice fringes are observed with high-resolution transmission electron microscopy (HR-TEM). In this case delocalization effects disturb imaging of the lattice structure in particular if 2 to 6 nm small nanoparticles are involved. Therefore, FePt nanocrystals were investigated by reconstructing amplitude and phase of the scattered electron wave from a focal series of HRTEM images, which can produce delocalization free and direct images of the crystal structure [4]. The formation of 5-fold twinned structures of 3 to 7 nm face-centered cubic FePt nanocrystals is investigated that were grown from a colloidal solution [1]. The results are compared with abinitio density functional (DFT) calculations of FePt particles with a diameter of larger than 2 nm. Image simulations were performed with the Accelrys Cerius2 software package (Version 4.6). Good agreement between the ab-initio calculations and the experimental data is found.

Synthesis and Magnetic Properties of FePt /Silica Core-Shell Nanoparticles

2010 ◽  
Vol 178 ◽  
pp. 291-295 ◽  
Author(s):  
Cui Xia Li ◽  
Zhi Hong Li ◽  
Xue Yan Du ◽  
Hai Xia Guo
Keyword(s):  
Magnetic Properties ◽  
Reverse Micelles ◽  
Core Shell ◽  
Fept Nanoparticles ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
Shell Nanoparticles ◽  
Transmission Electron ◽  
Face Centered ◽  
Core Shell Nanoparticles

FePt nanoparticles (NPS), ~2nm in diameter, were synthesized and then coated with silica (SiO2) shells ~1.5nm-thick using reverse micelles as nanoreactors. The silica-coated FePt core–shell (FePt @silica) NPS were characterized by direct techniques of transmission electron microscopy (TEM). The results showed that the silica shells prevented the aggregation in liquid comparing to their bare counterparts. The as-synthesized FePt@SiO2 NPS exhibited essential characteristics of superparamagnetic behavior, as investigated by a vibrating sample magnetometer (VSM). X-ray diffraction (XRD) studies proved that the annealing at 700 °C for 30min under argon atmosphere caused the crystal structure of FePt core to transform from disordered face centered cubic (fcc) to the chemically ordered L10 FePt with face-centered tetragonal (fct) structure. This phase transition caused the change of magnetic properties of the FePt@SiO2 particles from superparamagnetism to ferromagnetism.

Faceted antiphase boundaries in GaAs grown on Ge

1987 ◽  
Vol 45 ◽  
pp. 314-315
Author(s):  
N.-H. Cho ◽  
S. McKernan ◽  
C.B. Carter ◽  
K. Wagner
Keyword(s):  
Cross Section ◽  
Atomic Resolution ◽  
Face Centered Cubic ◽  
Electrical Behavior ◽  
Sphalerite Structure ◽  
Antiphase Boundaries ◽  
Transmission Electron ◽  
Face Centered ◽  
Quality Material ◽  
Simulated Images

Interest has recently increased in the possibility of growing III-V compounds epitactically on non-polar substrates to produce device quality material. Antiphase boundaries (APBs) may then develop in the GaAs epilayer because it has sphalerite structure (face-centered cubic with a two-atom basis). This planar defect may then influence the electrical behavior of the GaAs epilayer. The orientation of APBs and their propagation into GaAs epilayers have been investigated experimentally using both flat-on and cross-section transmission electron microscope techniques. APBs parallel to (110) plane have been viewed at the atomic resolution and compared to simulated images.Antiphase boundaries were observed in GaAs epilayers grown on (001) Ge substrates. In the image shown in Fig.1, which was obtained from a flat-on sample, the (110) APB planes can be seen end-on; the faceted APB is visible because of the stacking fault-like fringes arising from a lattice translation at this interface.

Microstructure Characterization of Ag Nanoparticles Prepared by Hydrothermal Method

2012 ◽  
Vol 476-478 ◽  
pp. 1138-1141
Author(s):  
Zhi Qiang Wei ◽  
Qiang Wei ◽  
Li Gang Liu ◽  
Hua Yang ◽  
Xiao Juan Wu
Keyword(s):  
Crystal Structure ◽  
Particle Size ◽  
Hydrothermal Method ◽  
Ag Nanoparticles ◽  
Average Particle Size ◽  
Average Particle ◽  
Face Centered Cubic ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Face Centered

Ag nanoparticles were successfully synthesized by hydrothermal method under the polyol system combined with traces of sodium chloride, Silver nitrate(AgNO3) and polyvinylpyrrolidone (PVP) acted as the silver source and dispersant respectively. The samples by this process were characterized via X-ray powder diffraction (XRD), Brunauer–Emmett–Teller (BET) adsorption equation, transmission electron microscopy (TEM) and the corresponding selected area electron diffraction (SAED) to determine the chemical composition, particle size, crystal structure and morphology. The experiment results indicate that the crystal structure of the samples is face centered cubic (FCC) structure as same as the bulk materials, The specific surface area is 24 m2/g, the particle size distribution ranging from10 to 50 nm, with an average particle size about 26 nm obtained by TEM and confirmed by XRD and BET results.

scholarly journals In-Situ TEM Annealing Observation of Helium Bubble Evolution in Pre-Irradiated FeCoNiCrTi0.2 Alloys

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3727
Author(s):  
Huanhuan He ◽  
Zhiwei Lin ◽  
Shengming Jiang ◽  
Xiaotian Hu ◽  
Jian Zhang ◽  
...  
Keyword(s):  
Vacuum Arc ◽  
In Situ Tem ◽  
Face Centered Cubic ◽  
Helium Bubble ◽  
High Entropy ◽  
Helium Bubbles ◽  
Transmission Electron ◽  
Bubble Evolution ◽  
Face Centered

The FeCoNiCrTi0.2 high-entropy alloys fabricated by vacuum arc melting method, and the annealed pristine material, are face centered cubic structures with coherent γ’ precipitation. Samples were irradiated with 50 keV He+ ions to a fluence of 2 × 1016 ions/cm2 at 723 K, and an in situ annealing experiment was carried out to monitor the evolution of helium bubbles during heating to 823 and 923 K. The pristine structure of FeCoNiCrTi0.2 samples and the evolution of helium bubbles during in situ annealing were both characterized by transmission electron microscopy. The annealing temperature and annealing time affect the process of helium bubbles evolution and formation. Meanwhile, the grain boundaries act as sinks to accumulate helium bubbles. However, the precipitation phase seems have few effects on the helium bubble evolution, which may be due to the coherent interface and same structure of γ’ precipitation and matrix.

scholarly journals The Examination of Calcium ion Implanted Alumina with Energy Filtered Transmission Electron Microscopy

1997 ◽  
Vol 3 (S2) ◽  
pp. 413-414
Author(s):  
E.M. Hunt ◽  
J.M. Hampikian ◽  
N.D. Evans
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Pure Aluminum ◽  
Lattice Parameter ◽  
Face Centered Cubic ◽  
Ion Channeling ◽  
Transmission Electron ◽  
Knoop Microhardness ◽  
Aluminum Nanocrystals ◽  
Face Centered

Ion implantation can be used to alter the optical response of insulators through the formation of embedded nano-sized particles. Single crystal alumina has been implanted at ambient temperature with 50 keV Ca+ to a fluence of 5 x 1016 ions/cm2. Ion channeling, Knoop microhardness measurements, and transmission electron microscopy (TEM) indicate that the alumina surface layer was amorphized by the implant. TEM also revealed nano-sized crystals ≈7 - 8 nm in diameter as seen in Figure 1. These nanocrystals are randomly oriented, and exhibit a face-centered cubic structure (FCC) with a lattice parameter of 0.409 nm ± 0.002 nm. The similarity between this crystallography and that of pure aluminum (which is FCC with a lattice parameter of 0.404 nm) suggests that they are metallic aluminum nanocrystals with a slightly dilated lattice parameter, possibly due to the incorporation of a small amount of calcium.Energy-filtered transmission electron microscopy (EFTEM) provides an avenue by which to confirm the metallic nature of the aluminum involved in the nanocrystals.

Epitaxial Ni nanoparticles on CaF2(001), (110) and (111) surfaces studied by three-dimensional RHEED, GIXD and GISAXS reciprocal-space mapping techniques

2017 ◽  
Vol 50 (3) ◽  
pp. 830-839 ◽  
Author(s):  
S. M. Suturin ◽  
V. V. Fedorov ◽  
A. M. Korovin ◽  
N. S. Sokolov ◽  
A. V. Nashchekin ◽  
...  
Keyword(s):  
Lattice Structure ◽  
Three Dimensional ◽  
Grazing Incidence ◽  
High Energy ◽  
Reciprocal Space ◽  
Mapping Technique ◽  
Face Centered Cubic ◽  
X Ray ◽  
Cubic Lattice ◽  
Face Centered

The development of growth techniques aimed at the fabrication of nanoscale heterostructures with layers of ferroic 3dmetals on semiconductor substrates is very important for their potential usage in magnetic media recording applications. A structural study is presented of single-crystal nickel island ensembles grown epitaxially on top of CaF2/Si insulator-on-semiconductor heteroepitaxial substrates with (111), (110) and (001) fluorite surface orientations. The CaF2buffer layer in the studied multilayer system prevents the formation of nickel silicide, guides the nucleation of nickel islands and serves as an insulating layer in a potential tunneling spin injection device. The present study, employing both direct-space and reciprocal-space techniques, is a continuation of earlier research on ferromagnetic 3dtransition metals grown epitaxially on non-magnetic and magnetically ordered fluorides. It is demonstrated that arrays of stand-alone faceted nickel islands with a face-centered cubic lattice can be grown controllably on CaF2surfaces of (111), (110) and (001) orientations. The proposed two-stage nickel growth technique employs deposition of a thin seeding layer at low temperature followed by formation of the islands at high temperature. The application of an advanced three-dimensional mapping technique exploiting reflection high-energy electron diffraction (RHEED) has proved that the nickel islands tend to inherit the lattice orientation of the underlying fluorite layer, though they exhibit a certain amount of {111} twinning. As shown by scanning electron microscopy, grazing-incidence X-ray diffraction (GIXD) and grazing-incidence small-angle X-ray scattering (GISAXS), the islands are of similar shape, being faceted with {111} and {100} planes. The results obtained are compared with those from earlier studies of Co/CaF2epitaxial nanoparticles, with special attention paid to the peculiarities related to the differences in lattice structure of the deposited metals: the dual-phase hexagonal close-packed/face-centered cubic lattice structure of cobalt as opposed to the single-phase face-centered cubic lattice structure of nickel.

Self-Organized Lead(II) Sulfide Quantum Dots Superlattice

MRS Advances ◽  
2017 ◽  
Vol 2 (15) ◽  
pp. 841-846 ◽  
Author(s):  
José Maria C. da Silva Filho ◽  
Victor A. Ermakov ◽  
Luiz G. Bonato ◽  
Ana F. Nogueira ◽  
Francisco C. Marques
Keyword(s):  
Quantum Dots ◽  
Interplanar Spacing ◽  
Face Centered Cubic ◽  
X Ray ◽  
Self Organized ◽  
Transmission Electron ◽  
The Mean ◽  
Face Centered ◽  
Pbs Quantum Dots ◽  
Deposited Films

ABSTRACTWe show that superlattice (SL) of PbS quantum dots (QD) can be easily prepared by drop casting of colloidal QD solution onto glass substrate and the ordering level can be controlled by the substrate temperature. A QD solution was dropped on glass and dried at 25, 40, 70 and 100°C resulting in formation of different SL structures. X-ray diffractograms (XRD) of deposited films show a set of sharp and intense peaks that are higher order satellites of a unique peak at 1.8 degrees (two theta), which corresponds, using the Bragg’s Law, to an interplanar spacing of 5.3 nm. The mean particles diameter, calculated through the broadening of the (111) peak of PbS using the Scherrer’s formula, were in agreement with the interplanar spacing. Transmission electron microscopy (TEM) measurements were also used to study the SL structure, which showed mainly a face centered cubic (FCC) arrangement of the QD. The photoluminescence (PL) spectrum of QD in the SL showed a shift toward lower energy compared to one in solution. It can be attributed to the fluorescence resonant energy transfer (FRET) between neighbors QD´s. Moreover, we observed greater redshift of PL peak for film with lower drying temperature, suggesting that it has a more organized structure.

scholarly journals Ti-V-C-Based Alloy with a FCC Lattice Structure for Hydrogen Storage

Molecules ◽  
2019 ◽  
Vol 24 (3) ◽  
pp. 552
Author(s):  
Bo Li ◽  
Liqing He ◽  
Jianding Li ◽  
Hai-Wen Li ◽  
Zhouguang Lu ◽  
...  
Keyword(s):  
Hydrogen Storage ◽  
Room Temperature ◽  
Lattice Structure ◽  
Activation Process ◽  
Face Centered Cubic ◽  
Hydrogen Storage Materials ◽  
Fcc Lattice ◽  
Bcc Structure ◽  
Face Centered ◽  
Fcc Structure

Here we report a Ti50V50-10 wt.% C alloy with a unique lattice and microstructure for hydrogen storage development. Different from a traditionally synthesized Ti50V50 alloy prepared by a melting method and having a body-centered cubic (BCC) structure, this Ti50V50-C alloy synthesized by a mechanical alloying method is with a face-centered cubic (FCC) structure (space group: Fm-3m No. 225). The crystalline size is 60 nm. This alloy may directly absorb hydrogen near room temperature without any activation process. Mechanisms of the good kinetics from lattice and microstructure aspects were discussed. Findings reported here may indicate a new possibility in the development of future hydrogen storage materials.

scholarly journals Green Synthesis of Silver Nanoparticles using Salacca zalacca Extract as Reducing Agent and It’s Antibacterial Activity

2019 ◽  
Vol 31 (12) ◽  
pp. 2804-2810
Author(s):  
Anti Kolonial Prodjosantoso ◽  
Oktanio Sigit Prawoko ◽  
Maximus Pranjoto Utomo ◽  
Lis Permana Sari
Keyword(s):  
Escherichia Coli ◽  
Silver Nanoparticles ◽  
Antibacterial Activity ◽  
Staphylococcus Epidermidis ◽  
Silver Ions ◽  
Reduction Reaction ◽  
Face Centered Cubic ◽  
Gram Positive Bacteria ◽  
Transmission Electron ◽  
Face Centered

In this article, the synthesis of silver nanoparticles through a reduction reaction process using Salacca zalacca extract is reported. The AgNPs were characterized using X-ray diffraction, transmission electron microscopy, Fourier transform infrared and UV-visible spectrophotometry methods. The AgNPs antibacterial activity was determined against of Gram-positive bacteria (Staphylococcus epidermidis) and Gram-negative bacteria (Escherichia coli). The main functional groups contained in Salacca zalacca extract are carbonyl, hydroxyl and nitrile groups, which are believed to reduce the silver ions to metal. The surface plasmon resonance values of brownish red AgNPs are in the range of 410 nm to 460 nm. The structure of AgNPs is face centered cubic (FCC). The diameter of silver nanoparticles crystallite is 14.2 ± 2.6 nm. The AgNPs growth inhibition zones of Escherichia coli and Staphylococcus epidermidis are 9.6 mm and 9.2 mm, respectively.

Sign in / Sign up

Export Citation Format

Share Document