INFLUENCE OF METHODS FOR ALTI MASTER ALLOY PRODUCTION ON ITS STRUCTURE AND EFFICIENCY IN ALUMINUM ALLOY MODIFICATION

2018 ◽  
pp. 45-52
Author(s):  
K. V. Nikitin ◽  
I. Yu. Timoshkin ◽  
V. I. Nikitin
Keyword(s):  
Electrical Conductivity ◽  
Cast Iron ◽  
Master Alloy ◽  
Alloy Structure ◽  
Cooling Rates ◽  
Master Alloys ◽  
Chill Mold ◽  
Modifying Effect ◽  
Determination Methods ◽  
Iron Mold

A comparative study on the effect of methods for obtaining AlTi4 modifying master alloys on the sizes of Al3Ti intermetallics is made. It is found that increasing cooling rates at solidification from 10–15 °C/s (crystallization in a hot cast iron mold, a plate 30 mm in thickness) to 60–65 °C/s (crystallization in a cold cast iron chill mold, a rod 20 mm in diameter, 170 mm in length) reduces the length and thickness of needle-shaped intermetallics almost twice (397×23 to 215×13 μm). At the same time, lower electrical conductivity and higher alloy density in a solid state are observed. Melt modification with 0,5 wt.% magnesium addition causes the formation of homogeneous 98×3 μm fine-needle intermetallics. The addition of magnesium slightly reduces electrical conductivity and density compared with the AlTi4 master alloy crystallized at the same cooling rate (60–65 °C/s). Modification of A97 grade aluminum and AK9ch alloy (Al–Si–Mg system) with the specified master alloys at the same amount of titanium added (0,01 wt.%) exerts hereditary influence on the density and electrical conductivity, and macrograin (A97) and dendrites of aluminium (AK9ch). The maximum modifying effect is provided by the AlTi4 master alloy containing 0,5 wt.% magnesium. When introduced into the alloy, it contributes to the formation of 10 μm aluminum dendrites 1427 pcs/mm2 in total in the alloy structure. When the AK9ch alloy is modified with the master alloy crystallized at cooling rates of 10–15 °C/s, 28 μm dendrites 672 pcs/mm2 in total are formed in the alloy structure. It is suggested to use density and electrical conductivity determination methods for express evaluation of master alloy modifying effectiveness.

scholarly journals Effect of cooling rates of production process of Al-3%B-3%Sr master alloy on grain refinement and eutectic modification efficiency in cast A356 alloy

2018 ◽  
Vol 192 ◽  
pp. 01036
Author(s):  
Krittee eidhed ◽  
Phisith muangnoy
Keyword(s):  
Grain Size ◽  
Grain Refinement ◽  
Master Alloy ◽  
Eutectic Silicon ◽  
A356 Alloy ◽  
Holding Time ◽  
Experimental Result ◽  
Cooling Rates ◽  
Eutectic Modification ◽  
Master Alloys

In this paper, size and morphology of the grain refiner and modifier particles in the Al-3%B-3%Sr master alloy production by using different cooling rates were investigated. Two Al-3%B-3%Sr master alloys were produced with 0.2 and 10°C/s, respectively. The grain refinement and eutectic modification efficiency of the Al-3%B-3%Sr master alloy were tested in casting process of A356 alloy by addition of 4wt.% and holding times for 10-120 min. The experimental result showed that microstructure of the M1 alloy (Slow cooling) consisted of larger solidified particles of AlB2, SrB6 and Al4Sr in the matrix of α-Al compared to the M2 alloy (Rapid cooling). The addition of the M1 alloy in cast A356 alloy, it was found that small grain size and fully modify eutectic silicon were obtained from the holding time in a range of 10-60 min. While the addition of M2 alloy, a small grain size was achieved in shorter holding time in a range of 10-30 min but the eutectic silicon was partly modify. From the thermal analyzed result, solidification of un-modified A356 alloy was changed after addition of Al-3%B-3%Sr master alloy. It was clearly observed that both the undercooling of nucleation and eutectic reaction was reduced and the solidification time was shifted to longer.

scholarly journals Sinter Hardening PM Steels Prepared through Hybrid Alloying

2021 ◽  
Vol 76 (2) ◽  
pp. 105-119
Author(s):  
S. Geroldinger ◽  
R. de Oro Calderon ◽  
C. Gierl-Mayer ◽  
H. Danninger
Keyword(s):  
Cross Sections ◽  
Master Alloy ◽  
Alloying Elements ◽  
Sintering Process ◽  
Alloying Element ◽  
Cooling Rates ◽  
Advantages And Disadvantages ◽  
Master Alloys ◽  
Oxygen Sensitive ◽  
Cct Diagrams

Abstract In powder metallurgy (PM), there are several ways of introducing alloying elements into a PM material in order to adjust a certain alloying element content. Each alloying route has its advantages and disadvantages. Master alloys (MA), powders with a high content of typically several alloying elements, can be added in small amounts to a base powder, especially to introduce oxygen sensitive elements such as Cr, Mn, and Si. In addition, the master alloy can be designed in such a way that a liquid phase is formed intermediately during the sintering process to improve the distribution of alloying elements in the material and to accelerate homogenization. In this study, such master alloys were combined with pre-alloyed base powders to form hybrid alloyed mixtures with the aim of improving the material‘s sinter hardenability. The hybrid alloys were compared with mixtures of master alloy and plain Fe as reference material. The sinter hardenability of all materials was determined by generating CCT diagrams recorded with 13 different cooling rates. These were verified by metallographic cross-sections of specimens treated at common cooling rates of 3 and 1.5 K/s and subsequent hardness measurements of the microhardness (HV 0.1) of the microstructural constituents and the apparent hardness (HV 30). ◼

Application Research of Al-Fe-P Master Alloy on Modifying ZL109 Alloys

2013 ◽  
Vol 750-752 ◽  
pp. 655-658
Author(s):  
Guang Hui Qi
Keyword(s):  
Mechanical Properties ◽  
Master Alloy ◽  
Application Research ◽  
Technological Parameters ◽  
Piston Alloy ◽  
Primary Si ◽  
Average Grain Size ◽  
Master Alloys ◽  
Modifying Effect

In order to settle the environmental pollution and improve the excellent rate of products, ZL109 piston alloy modified by Al9Fe3P master alloy was prepared in factory. The microstructures and mechanical properties of ZL109 piston alloy were invested respectively. The technological parameters and modifying effect of using Al9Fe3P alloy were researched too. Experiments show that high quality of ZL109 pistons can be produced by adding 0.4~0. 5wt% Al9Fe3P master alloy at 760-770°C.The maxim and average grain size of primary Si decrease largely, less than 66μm and 40μm respectively, and the mechanical properties were improved accordingly. It was proved that Al-Fe-P master alloys have advantages such as no pollution, no reaction slag, shorter modifying time and saving energy, which would reduce the total cost of piston products. So Al-Fe-P master alloy is a promising modifier to refine ZL109 piston alloys.

The influence of gadolinium on Al–Ti–C master alloy and its refining effect on AZ31 magnesium alloy

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Wenxue Fan ◽  
Hai Hao
Keyword(s):  
Mechanical Properties ◽  
Magnesium Alloy ◽  
Grain Refinement ◽  
Magnesium Alloys ◽  
Master Alloy ◽  
Cast Alloy ◽  
Az31 Magnesium Alloy ◽  
Synthesis Mechanism ◽  
Refining Effect ◽  
Master Alloys

Abstract Grain refinement has a significant influence on the improvement of mechanical properties of magnesium alloys. In this study, a series of Al–Ti–C-xGd (x = 0, 1, 2, 3) master alloys as grain refiners were prepared by self-propagating high-temperature synthesis. The synthesis mechanism of the Al–Ti–C-xGd master alloy was analyzed. The effects of Al–Ti–C-xGd master alloys on the grain refinement and mechanical properties of AZ31 (Mg-3Al-1Zn-0.4Mn) magnesium alloys were investigated. The results show that the microstructure of the Al–Ti–C-xGd alloy contains α-Al, TiAl3, TiC and the core–shell structure TiAl3/Ti2Al20Gd. The refining effect of the prepared Al–Ti–C–Gd master alloy is obviously better than that of Al–Ti–C master alloy. The grain size of AZ31 magnesium alloy was reduced from 323 μm to 72 μm when adding 1 wt.% Al–Ti–C-2Gd master alloy. In the same condition, the ultimate tensile strength and elongation of as-cast alloy were increased from 130 MPa, 7.9% to 207 MPa, 16.6% respectively.

A High Effective and Low-Cost Modifier for Hypereutectic Al-Si Alloys

2013 ◽  
Vol 721 ◽  
pp. 282-286
Author(s):  
Guang Hui Qi
Keyword(s):  
Grain Size ◽  
Master Alloy ◽  
Low Cost ◽  
Environment Pollution ◽  
Casting Method ◽  
Good Future ◽  
Primary Si ◽  
Average Grain Size ◽  
Master Alloys

In order to settle environment pollution and provide a high effective and low-cost modifier for refining the primary Si in hypereutectic Al-Si alloys, Al-Fe-P master alloys containing 2.0~5.0% phosphorus have been invented by casting method. The Al-Fe-P master alloys can be conveniently produced and an excellent modification can be obtained by adding 0.3~0.8wt% Al-Fe-P master alloy in Al-Si alloys containing 12%-25% Si at a relatively lower modifying temperature. The number of primary Si increases obviously and the average grain size of primary Si decreases largely, less than 50μm. Furthermore Al-Fe-P master alloys have many advantages, such as low cost, convenient operation technology, no pollution, stable and long-term modification effect, easy storage and etc. Al-Fe-P master alloys have overcome the shortages of current modifier and have a good future for hypereutectic Al-Si alloy modification.

Influence of Reaction Temperature for the Manufacturing of Al-3Ti and Al-3B Master Alloys and their Grain Refining Efficiency on a Al-7Si Alloy

2007 ◽  
Vol 29-30 ◽  
pp. 111-115 ◽  
Author(s):  
S.A. Kori ◽  
V. Auradi
Keyword(s):  
Size Distribution ◽  
Grain Refinement ◽  
Reaction Temperature ◽  
Master Alloy ◽  
Induction Furnace ◽  
Grain Refining ◽  
Refining Efficiency ◽  
Master Alloys ◽  
Halide Salts ◽  
Titanium Fluoride

In the present work binary Al-3Ti and Al-3B master alloys were prepared at different reaction temperatures in an induction furnace by the reaction of halide salts like potassium fluoborate and potassium titanium fluoride with liquid molten Al. The indigenously developed master alloys were used for grain refinement studies of Al-7Si alloy and evaluated for their grain refining ability by CACCA studies. The present results suggest that, the reaction temperature influences the size, size distribution and morphology of the intermetallic (Al3Ti in Al-3Ti, and AlB2/AlB12 in Al-3B) particles present in Al-3Ti and Al-3B master alloys. Grain refinement studies of Al-7Si alloy reveal that, Al-3Ti and Al-3B master alloys prepared at 8000C-60 min. have shown better grain refining efficiency on Al- 7Si alloy when compared to the master alloys prepared at 9000C-60 min and 10000C-60 min respectively. In addition, B-rich Al-3B master alloy shows efficient grain refinement than Ti rich Al- 3Ti master alloy.

scholarly journals Production of low impurity aluminium rotor for motor efficiency enhancement

2018 ◽  
Vol 192 ◽  
pp. 01043
Author(s):  
Savitri Payakkapol ◽  
Nattapon Chayopitak ◽  
Panya Kunsuwan ◽  
Naoto Ohtake ◽  
Sompong Srimanosaowapak
Keyword(s):  
Electrical Conductivity ◽  
Master Alloy ◽  
Single Phase ◽  
Induction Motors ◽  
Impurity Content ◽  
Efficiency Enhancement ◽  
Motor Efficiency

Induction motors have been widely used in various electrical applications. However, their efficiency are still limited due to losses occurring during operation, especially for smaller ratings. Higher the electrical conductivity of motor rotor by lower its impurity content is one of practical and simple way to improve motor efficiency. The aim of this work is to reduce the impurity content of aluminium rotor by addition of boron in the form of Al-5wt%B master alloy and Na2B4O7-NaCl-KCl flux, and then sedimention of their precipitated particles. The purer melt was then cast as rotors for single-phase induction motors. With the amount of addition of boron in aluminium melt in this work, boron in Al-5wt%B master alloy was more pronounced in removing impurities in aluminium melt than that in Na2B4O7. It was found that the rotors made of aluminium melt with lower impurity contents and hence higher electrical conductivity resulted in more enhancement of motor efficiency.

The Behavior of AlTiC Master Alloys in Grain Refining of Commercial and High Pure Aluminum

2005 ◽  
Vol 475-479 ◽  
pp. 313-316
Author(s):  
Jian Guo Li ◽  
Min Huang ◽  
Zimu Shi ◽  
Dong Yu Liu
Keyword(s):  
Master Alloy ◽  
Heterogeneous Nucleation ◽  
Pure Aluminum ◽  
Grain Refining ◽  
Refining Efficiency ◽  
Master Alloys

The AlTiC master alloy has been prepared in different components to refine 99.8%Al and 99.98％Al, then compared to two typical Al5Ti1B in refining efficiency and the grain nuclear. The result showed that the refining efficiency seemed better if the nucleation of high pure aluminum revealed complexity and variety. It may due to that the latency heterogeneous nucleation was efficient on the whole, consequently accelerated refining efficiency.

Production of the Al–B master alloy by KBF4and B 2O3aluminothermic reduction in molten salt flux medium

2019 ◽  
pp. 20-29
Author(s):  
A. A. Kataev ◽  
O. Yu. Tkacheva ◽  
N. G. Molchanova ◽  
Yu. P. Zaikov
Keyword(s):  
Master Alloy ◽  
Minimum Degree ◽  
Decomposition Temperature ◽  
Raw Material ◽  
Salt Flux ◽  
Recovery Ratio ◽  
Cryolite Ratio ◽  
Molten Mixture ◽  
Master Alloys ◽  
Degree Of Extraction

The study covers the process of obtaining the Al–B master alloy by the KBF4and B2O3aluminothermic reduction using KF–AlF3and KF–NaF–AlF3fluoride fluxes at 983 and 1123 К, respectively, and KCl–NaCl–KF chloride-fluoride fluxes at Т= 1173÷1223 К. All experiments were carried out under the same conditions: molten mixture stirring rate was 400 rpm, synthesis duration was 30min. The maximum amount of boron (1,5 %) in the Al–B alloy was obtained when using KBF4(3 % per B) as a boron-containing raw material in the KF–AlF3medium with a molar (cryolite) ratio (CR) of KF/AlF3equal to 1,3, atТ= 983 К, while boron recovery ratio did not exceed 75 %. Comparable results were obtained in experiments with KF–NaF–AlF3f lux (CR = 1,5) at Т= 1123 К. However, with the increased concentration of fed boron its recovery ratio decreased substantially. It is connected with the higher decomposition temperature of not only KBF4, but also less thermally stable NaBF4 formed as a result of exchange reaction in the melt. Therefore it is not recommended to use sodium salts as a f lux component. The Al–B master alloys obtained by KBF4reduction in fluoride fluxes were solid solutions of B in Al containing the AlB2intermetallic compound. The lowest amount of boron in aluminum with the minimum degree of extraction was obtained in experiments with the B2O3in molten KF–AlF3with CR = 1,5. Nevertheless, the results of scanning electron microscopy indicate a uniform distribution of B over the Al matrix and the absence of intermetallic compounds, while a large amount of Al2O3was found, which is the product of B2O3reactions with both liquid Al and KF–AlF3flux.

Sign in / Sign up

Export Citation Format

Share Document