scholarly journals New diamond composite tools and their impact on AISI 4140 alloy steel surface after slide burnishing

Mechanik ◽  
2019 ◽  
Vol 92 (10) ◽  
pp. 610-615
Author(s):  
Magdalena Szutkowska ◽  
Daniel Toboła ◽  
Lucyna Jaworska ◽  
Marcin Rozmus
Keyword(s):  
Alloy Steel ◽  
Steel Surface ◽  
X Ray Diffraction ◽  
Diamond Composite ◽  
X Ray ◽  
Young’S Moduli ◽  
Transmission Electron ◽  
Steel Bar ◽  
Aisi 4140 ◽  
Slide Burnishing

Working parts of slide burnishing tools were made from two new diamond composites with ceramic bonding: MAX Ti3GeC2 and TiB2nano phases, respectively. Microstructure and micro composition were analyzed by scanning and transmission electron microscopy and X-ray diffraction. Vickers hardness HV1 values were 36 and 46 GPa, Young’s moduli 490 and 560 GPa, tensile strengths 400 and 560 MPa, fracture toughness 8.4 and 11.0 MPa·m1/2 and friction coefficient values 0.63 and 0.56, respectively for the composites with MAX Ti3GeC2 and TiB2nano phases. The tools were tested by slide burnishing on previously turned AISI 4140 alloy steel bar. Improvement in the surface geometric structure was demonstrated for both materials, more so in the case of TiB2nano phase, as compared to burnishing bycomposites with MAX Ti3GeC2 phase.

Microstructure Study of Spinel Plasma Coatings

1998 ◽  
Author(s):  
G. Lallemand ◽  
S. Fayeulle ◽  
D. Treheux ◽  
C. Esnouf
Keyword(s):  
Electron Microscopy ◽  
X Ray Diffraction ◽  
Frequency Method ◽  
X Ray ◽  
Young’S Moduli ◽  
Transmission Electron ◽  
Splat Solidification ◽  
Coating Microstructure ◽  
Plasma Sprayed ◽  
Rate Gradient

Abstract Spinel powders of different compositions were fabricated fir their good properties of chemical resistance. These powders were plasma sprayed on steels and their microstructure was investigated by scanning electron microscopy (SEM), microanalysis, X-ray diffraction and transmission electron microscopy (TEM). Due to the powder fabrication process, coatings were very heterogeneous in composition, but had the spinel structure. TEM observations pointed out that splat solidification occured with a cooling rate gradient leading to different crystallization inside a lamella. Young's moduli by the coatings were measured by the resonant frequency method and the correlation with coating microstructure was discussed.

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

A High Resolution Study of G.P. Zones in Aluminum - 4.2 at % Silver

1982 ◽  
Vol 40 ◽  
pp. 722-723 ◽  
Author(s):  
R. Gronsky
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
High Resolution ◽  
Computer Simulations ◽  
Structural Characteristics ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Resolution Study

The phenomenon of clustering in Al-Ag alloys has been extensively studied since the early work of Guinierl, wherein the pre-precipitation state was characterized as an assembly of spherical, ordered, silver-rich G.P. zones. Subsequent x-ray and TEM investigations yielded results in general agreement with this model. However, serious discrepancies were later revealed by the detailed x-ray diffraction - based computer simulations of Gragg and Cohen, i.e., the silver-rich clusters were instead octahedral in shape and fully disordered, atleast below 170°C. The object of the present investigation is to examine directly the structural characteristics of G.P. zones in Al-Ag by high resolution transmission electron microscopy.

Identification of calcium oxalate crystals in dried or fixed tobacco leaf

1984 ◽  
Vol 42 ◽  
pp. 288-289
Author(s):  
Vicki L. Baliga ◽  
Mary Ellen Counts
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Calcium Oxalate ◽  
Growth And Development ◽  
Polarized Light ◽  
Calcium Oxalate Crystals ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Calcium is an important element in the growth and development of plants and one form of calcium is calcium oxalate. Calcium oxalate has been found in leaf seed, stem material plant tissue culture, fungi and lichen using one or more of the following methods—polarized light microscopy (PLM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and x-ray diffraction.Two methods are presented here for qualitatively estimating calcium oxalate in dried or fixed tobacco (Nicotiana) leaf from different stalk positions using PLM. SEM, coupled with energy dispersive x-ray spectrometry (EDS), and powder x-ray diffraction were used to verify that the crystals observed in the dried leaf with PLM were calcium oxalate.

Transmission electron microscope studies in special ceramics

1978 ◽  
Vol 36 (1) ◽  
pp. 268-269
Author(s):  
A. Zangvil ◽  
L.J. Gauckler ◽  
G. Schneider ◽  
M. Rühle
Keyword(s):  
Phase Diagrams ◽  
Crystal Structures ◽  
Thin Foil ◽  
Limited Extent ◽  
Complex Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Electron Microscopes ◽  
Lattice Resolution

The use of high temperature special ceramics which are usually complex materials based on oxides, nitrides, carbides and borides of silicon and aluminum, is critically dependent on their thermomechanical and other physical properties. The investigations of the phase diagrams, crystal structures and microstructural features are essential for better understanding of the macro-properties. Phase diagrams and crystal structures have been studied mainly by X-ray diffraction (XRD). Transmission electron microscopy (TEM) has contributed to this field to a very limited extent; it has been used more extensively in the study of microstructure, phase transformations and lattice defects. Often only TEM can give solutions to numerous problems in the above fields, since the various phases exist in extremely fine grains and subgrain structures; single crystals of appreciable size are often not available. Examples with some of our experimental results from two multicomponent systems are presented here. The standard ion thinning technique was used for the preparation of thin foil samples, which were then investigated with JEOL 200A and Siemens ELMISKOP 102 (for the lattice resolution work) electron microscopes.

A TEM investigation of a hyper-eutectic lead-tin alloy

1988 ◽  
Vol 46 ◽  
pp. 562-563
Author(s):  
John A. Sutliff
Keyword(s):  
Volume Diffusion ◽  
Eutectic Mixture ◽  
Precipitation Reaction ◽  
Directionally Solidified ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Diffusion Controlled ◽  
Discontinuous Precipitation Reaction ◽  
Controlled Precipitation

Near-eutectic Pb-Sn alloys are important solders used by the electronics industry. In these solders, the eutectic mixture, which solidifies last, is the important microstructural consituent. The orientation relation (OR) between the eutectic phases has previously been determined for directionally solidified (DS) eutectic alloys using x-ray diffraction or electron chanelling techniques. In the present investigation the microstructure of a conventionally cast, hyper-eutectic Pb-Sn alloy was examined by transmission electron microscopy (TEM) and the OR between the eutectic phases was determined by electron diffraction. Precipitates of Sn in Pb were also observed and the OR determined. The same OR was found in both the eutectic and precipitation reacted materials. While the precipitation of Sn in Pb was previously shown to occur by a discontinuous precipitation reaction,3 the present work confirms a recent finding that volume diffusion controlled precipitation can also occur.Samples that are representative of the solder's cast microstructure are difficult to prepare for TEM because the alloy is multiphase and the phases are soft.

The Effect of the Microstructure of Diffusion Barriers on the Palladium Activation for Electroless Copper Deposition

2002 ◽  
Vol 716 ◽  
Author(s):  
Seok Woo Hong ◽  
Yong Sun Lee ◽  
Ki-Chul Park ◽  
Jong-Wan Park
Keyword(s):  
Electron Microscopy ◽  
Diffusion Barriers ◽  
Copper Deposition ◽  
X Ray Diffraction ◽  
Plan View ◽  
X Ray ◽  
Transmission Electron ◽  
Electroless Copper ◽  
Sheet Resistance Measurement ◽  
Scanning Electron

AbstractThe effect of microstructure of dc magnetron sputtered TiN and TaN diffusion barriers on the palladium activation for autocatalytic electroless copper deposition has been investigated by using X-ray diffraction, sheet resistance measurement, field emission scanning electron microscopy (FE-SEM) and plan view transmission electron microscopy (TEM). The density of palladium nuclei on TaN diffusion barrier increases as the grain size of TaN films decreases, which was caused by increasing nitrogen content in TaN films. Plan view TEM results of TiN and TaN diffusiton barriers showed that palladium nuclei formed mainly on the grain boundaries of the diffusion barriers.

Palladium Nanowire Thin Films via Template Growth

2003 ◽  
Vol 775 ◽  
Author(s):  
Donghai Wang ◽  
David T. Johnson ◽  
Byron F. McCaughey ◽  
J. Eric Hampsey ◽  
Jibao He ◽  
...  
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Thin Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Conductive Substrate ◽  
Palladium Nanowires ◽  
Efficient Route ◽  
Silica Thin Film

AbstractPalladium nanowires have been electrodeposited into mesoporous silica thin film templates. Palladium continually grows and fills silica mesopores starting from a bottom conductive substrate, providing a ready and efficient route to fabricate a macroscopic palladium nanowire thin films for potentially use in fuel cells, electrodes, sensors, and other applications. X-ray diffraction (XRD) and transmission electron microscopy (TEM) indicate it is possible to create different nanowire morphology such as bundles and swirling mesostructure based on the template pore structure.

Nano-Folded Gold Electrocatalysts Enhance the Selectivity of Carbon Dioxide Reduction

2019 ◽  
Author(s):  
Kam Sang Kwok ◽  
Yuxuan Wang ◽  
Michael Cao ◽  
Hao Shen ◽  
Weinan Xu ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Mass Transport ◽  
Gold Film ◽  
X Ray Diffraction ◽  
Thin Gold Film ◽  
Faradaic Efficiency ◽  
X Ray ◽  
Transmission Electron ◽  
Carbon Monoxide Formation ◽  
Catalytic Interfaces

<p>The local structure and geometry of catalytic interfaces can influence the selectivity of chemical reactions. Here, using a pre-strained polymer, we uniaxially compress a thin gold film to form a nano-folded catalyst. We observe two kinds of folds and can tune the ratio of loose to tight folds by varying the extent of pre-strain in the polymer. We characterize the nano-folded catalysts using x-ray diffraction, scanning, and transmission electron microscopy. We observe grain reorientation and coarsening in the nano-folded gold catalysts. Electroreduction of carbon dioxide with these nano-folded catalysts reveals an enhancement of Faradaic efficiency for carbon monoxide formation by a factor of about four. This result suggests that electrolyte mass transport limitations and an increase of the local pH in the tight folds of the catalyst outweigh the effects of alterations in grain characteristics. Together, our studies demonstrate that nano-folded geometries can significantly alter grain characteristics, mass transport, and catalytic selectivity. </p>

Surfactant involved in Copper Sulfide Nanocrystallites Synthesis

2009 ◽  
Vol 59 (12) ◽  
Author(s):  
Claudia Maria Simonescu ◽  
Valentin Serban Teodorescu ◽  
Camelia Capatina
Keyword(s):  
Copper Sulfide ◽  
X Ray Diffraction ◽  
Reaction Parameters ◽  
Reaction Conditions ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Shape Of Nanoparticles ◽  
Tem Transmission Electron Microscopy ◽  
Shape And Size

This paper presents the obtaining of copper sulfide CuS (covelite) from Cu(CH3COO)2.H2O and thioacetamide (TAA) system. The reaction was conducted in presence or absence of sodium-bis(2-ethylhexyl) sulfosuccinate (Na-AOT). The effects of various reaction parameters on the size and on the shape of nanoparticles have been examined. CuS obtained was characterized by X ray diffraction, IR spectroscopy, TEM � transmission electron microscopy and SAED selected area electron diffraction. The influence of surfactant to the shape and size of CuS (covellite) nanocrystals was established. The size of the nanocrystals varied from 10-60 nm depending on the reaction conditions such as quantity of surfactant.

Sign in / Sign up

Export Citation Format

Share Document