scholarly journals DESIGN OF COMPOSITE GIRDER STRUCTURE BRIDGE OF SELUANG-1 RIVER PT LIFERE AGRO KAPUAS, KAPUAS DISTRICT

CERUCUK ◽  
2021 ◽  
Vol 4 (1) ◽  
pp. 1
Author(s):  
A. Rizki Fauzi ◽  
Markawie Markawie
Keyword(s):  
Bearing Capacity ◽  
Palm Oil ◽  
Steel Structures ◽  
Structure Type ◽  
Steel Buildings ◽  
Composite Girder ◽  
Pile Type ◽  
Earthquake Resilience ◽  
Plantation Crops ◽  
Diaphragm Beam

The bridge at the Seluang-1 river is located around the palm oil plantation land owned by PT Lifere Agro Kapuas, Kapuas Regency, Central Kalimantan. In this Seluang-1 river, a bridge is planned to be built to facilitate the mobilization of palm oil plantation crops and other matters as well as transportation in the PT Lifere Agro Kapuas area because before there was a bridge the transportation traffic was cut off by the river so it had to circle quite a long way. The bridge is designed as a bridge with composite girder structure type.          The methodology in the design of loading uses the SNI 1725-2016 concerning on the Loading Standards for Bridges and SNI 2833-2016 concerning on the Earthquake Resilience Planning Standards for Bridges. For methodology in designing concrete structures refer to SNI 2847-2013 concerning Structural Concrete Requirements for Buildings and methodology in designing steel structures refers to SNI 1729-2015 concerning Specifications for Structural Steel Buildings. The material used for abutment uses reinforced concrete material. The methodology in calculating the bearing capacity of the foundation uses the method by Mayerhof and also the method by Kazuto Nakazawa, while the methodology in calculating the lateral bearing capacity uses the Broms method, with the efficiency of the pile using a graph by O’Neill.          From the results of topographic measurements taken a bridge design with a span of 30 m with a total bridge width of 7 m. The slab design is 25 cm thick with the compressive strenght of concrete is fc’ 30 MPa (K-350). The steel girder beam used WF Profile 1350.800.100.130 and the diaphragm beam used WF Profile 250.125.6.9 with BJ55 steel quality (fy 410 MPa). Whereas in the lower structure, the abutment designed with a height of 350 cm, a width of 320 cm and a length of 850 cm, was used with compressive strenght of concrete is fc’ 30 MPa (K-350). In the foundation used Spun Pile type piles with a diameter of 60 cm with a depth of 30 m piling as much as 8 piles on one abutment. Obtained Qallow = 116,37 tons > Qload = 114,69 tons so that the foundation is declared safe. The planned budget for the construction of a bridge on the Seluang-1 river is Rp 8.990.566.000,00.-              

Seismic Performance Assessment of Existing Steel Buildings: A Case Study

2018 ◽  
Vol 763 ◽  
pp. 1067-1076 ◽  
Author(s):  
Luigi di Sarno ◽  
Fabrizio Paolacci ◽  
Anastasios G. Sextos
Keyword(s):  
Numerical Study ◽  
Central Italy ◽  
Steel Structures ◽  
Eurocode 8 ◽  
Building Structures ◽  
Steel Buildings ◽  
Seismic Performance Assessment ◽  
Masonry Infills ◽  
Main Shocks

Numerous existing steel framed buildings located in earthquake prone regions world-wide were designed without seismic provisions. Slender beam-columns, as well as non-ductile beam-to-column connections have been employed for multi-storey moment-resisting frames (MRFs) built before the 80’s. Thus, widespread damage due to brittle failure has been commonly observed in the past earthquakes for steel MRFs. A recent post-earthquake survey carried out in the aftermath of the 2016-2017 Central Italy seismic swarm has pointed out that steel structures may survive the shaking caused by several main-shocks and strong aftershocks without collapsing. Inevitably, significant lateral deformations are experienced, and, in turn, non-structural components are severely damaged thus inhibiting the use of the steel building structures. The present papers illustrates the outcomes of a recent preliminary numerical study carried out for the case of a steel MRF building located in Amatrice, Central Italy, which experienced a series of ground motion excitations suffering significant damage to the masonry infills without collapsing. A refined numerical model of the sample structure has been developed on the basis of the data collected on site. Given the lack of design drawings, the structure has been re-designed in compliance with the Italian regulations imposed at the time of construction employing the allowable stress method. The earthquake performance of the case study MRF has been then investigated through advanced nonlinear dynamic analyses and its structural performance has been evaluated according to Eurocode 8-Part 3 for existing buildings. The reliability of the codified approaches has been evaluated and possible improvements emphasized.

New Zealand Research Applications of, and Developments in, Low Damage Technology for Steel Structures

2018 ◽  
Vol 763 ◽  
pp. 3-10 ◽  
Author(s):  
Gregory A. MacRae ◽  
George Charles Clifton ◽  
Michel Bruneau
Keyword(s):  
New Zealand ◽  
Large Scale ◽  
Base Isolation ◽  
Steel Structures ◽  
Small Towns ◽  
Steel Buildings ◽  
Construction Methods ◽  
Steel Framing ◽  
Friction Pendulum ◽  
Building Demolition

Over the past few years, the South Island of New Zealand has been subject to significant sequences of earthquake shaking. In particular, 2010-2011 events affected the city of Christchurch resulting in large scale demolition of buildings. Also, the recent and continuing 11/2016 events caused severe damage in the countryside, in small towns, and moderate damage further afield. This paper describes “low damage construction” methods being used in NZ, and especially in the Christchurch rebuild, to limit the possibility of building demolition in future large seismic events. The buildings used in the Christchurch rebuild are generally supported by structural steel framing. These steel buildings include BRB systems, EBF systems with replaceable active links, rocking systems, base isolation using friction pendulum systems and/or lead-rubber dissipaters, RBS beams, lead extrusion dissipaters, yielding flexural dissipaters, and friction connections. Concerns about a number of currently used systems are discussed.

Steel Buildings' Seismic and Interaction Behavior, Under Different Shapes of Tunnel Drilling

2016 ◽  
Vol 7 (2) ◽  
pp. 1-23 ◽  
Author(s):  
Arash Rostami ◽  
Hamid Alielahi ◽  
Abdoreza Sarvghad Moghadam ◽  
Mahmood Hosseini
Keyword(s):  
Urban Areas ◽  
Steel Structures ◽  
Urban Environments ◽  
Steel Buildings ◽  
Underground Structures ◽  
Residential Areas ◽  
Earthquake Records ◽  
Structural Responses ◽  
Different Shapes ◽  
And Behavior

Development of civil engineering science has introduced tunneling as an important option in reducing the traffic volume of urban environments. Digging tunnels, in every depth, causes changes in the surface ground structure; tunneling in urban areas, especially when has passed through the residential areas has its own particular importance; therefore, having knowledge about tunnels' behavior and effects of diggings is necessary, and in order to prevent unpredictable damages to the structures is one of the requirements of designing. The performance and behavior of underground structures have been studied by many researchers, but the effects of tunneling on earthquake records and its effects on structures above the ground has taken less attention. This study will try to check earthquake record changes and their impact on steel structures located on top part of the tunnels, and has done this issue with digging some circular tunnels. The results indicate that, tunneling alters the earthquake records and also has affections on structural responses.

scholarly journals Study on Calculation of Bearing Capacity of Axially Loaded CFRP-Strengthened Cold-Formed Thin-Walled Lipped Channel Steel Columns

2020 ◽  
Vol 2020 ◽  
pp. 1-16
Author(s):  
Yanan Sun ◽  
Pengfei Li ◽  
Guojin Qin
Keyword(s):  
Carbon Fiber ◽  
Bearing Capacity ◽  
Load Capacity ◽  
Slenderness Ratio ◽  
Steel Structures ◽  
Fiber Reinforced ◽  
Bonding Agents ◽  
Steel Column ◽  
Thin Walled ◽  
Carbon Fiber Reinforced

With the development of carbon fiber reinforced composites and the continuous improvement of the properties of bonding agents, scholars recommended using carbon fiber reinforced plastics (CFRP) to enhance cold-formed thin-walled C-shaped steel structures. It can provide a fast and effective way to strengthen and repair damaged steel structures. However, discussion on the bearing capacity calculation of cold-formed thin-walled C-section steel column strengthened by CFRP was limited. Also, the relevant influencing factors (the number of CFRP reinforcement layers), the orientation of CFRP (horizontal, vertical), and the location of CFRP reinforcement (web + flanges + lips, web + flanges, web, and flanges) were overlooked in calculating the bearing capacity of cold-formed thin-walled C-section steel column strengthened by CFRP. Then, the calculation result of the load capacity will be inaccurate. This work, therefore, studied the effects of CFRP reinforcement layers, CFRP direction, and CFRP reinforcement position on the ultimate load of CFRP-strengthened cold-formed thin-walled C-section steel column. A three-dimensional (3D) finite element model of cold-formed thin-walled steel strengthened by CFRP was established to discuss the bearing capacity under axial compression. Furthermore, a method for calculating the bearing capacity of the CFRP-strengthened cold-formed thin-walled C-section steel column was proposed based on the direct strength methods (DSM). The results indicate that not only the slenderness ratio, section size, and length of members but also the number of CFRP reinforcement layers and orientation of CFRP have an impact on the calculation of bearing capacity. The equation modified in this work has excellent accuracy and adaptability. Predicting the bearing capacity of reinforced members is necessary to give full play to the performance of CFRP accurately. Thus, the methods proposed can provide a reference value for practical engineering.

scholarly journals The Effect of Long Duration Earthquakes on the Overall Seismic Behavior of Steel Structures Designed According to Eurocode 8 Provisions

Vibration ◽  
2020 ◽  
Vol 3 (4) ◽  
pp. 464-477
Author(s):  
Panagiota Katsimpini ◽  
Foteini Konstandakopoulou ◽  
George A. Papagiannopoulos ◽  
Nikos Pnevmatikos ◽  
George D. Hatzigeorgiou
Keyword(s):  
Seismic Performance ◽  
Time History ◽  
Steel Structures ◽  
Eurocode 8 ◽  
Steel Buildings ◽  
Long Duration ◽  
Base Steel ◽  
Fixed Base ◽  
Permanent Settlement ◽  
Nonlinear Time History

Premature and simultaneous buckling of several steel braces in steel structures due to the prolonged duration of a seismic motion is one of the issues that must be addressed in the next version of Eurocode 8. In an effort to contribute towards the improvement of the seismic design provisions of Eurocode 8, an evaluation of the overall behavior of some steel building-foundation systems under the action of long duration seismic motions is performed herein by means of nonlinear time-history seismic analyses, taking into account soil–structure interaction (SSI) effects. In particular, the maximum seismic response results—in terms of permanent interstorey drifts, overturning moments and base shears of the steel buildings as well as of the permanent settlement and tilting of their foundations—are computed. It is found that the seismic performance of steel buildings when subjected to long duration seismic motions is: (i) acceptable for the two and five-storey fixed base steel buildings and for the two-storey steel buildings with SSI effects included; (ii) unacceptable for the eight-storey fixed base steel buildings and for the five and eight-storey steel buildings with SSI effects included. In all cases of steel buildings with SSI effects included, the seismic performance of the mat foundation, as expressed by the computed values of residual settlement and tilting, is always acceptable.

Structural Steel Performance Following Severe Earthquake Loading

2011 ◽  
Vol 25 (31) ◽  
pp. 4149-4153
Author(s):  
W. G. Fergusona ◽  
C. K. Seal ◽  
M. A. Hodgson ◽  
G. C. Clifton
Keyword(s):  
Plastic Strain ◽  
Structural Steel ◽  
Central Business District ◽  
Steel Structures ◽  
Earthquake Loading ◽  
Structural Elements ◽  
Steel Buildings ◽  
Structural Element ◽  
Tension And Compression ◽  
Business District

The second Christchurch earthquake on February 22, 2011, Magnitude 6.35, generated more intense shaking in the Central Business District than the September 4, 2010 Darfield earthquake, Magnitude 7.1. The second earthquake was closer to the CBD and at shallow depth, resulting in peak ground accelerations 3 times higher. There was significant failure of unreinforced masonry buildings and collapse of a few reinforced concrete buildings, leading to loss of life. Steel structures on the whole performed well during the earthquake and the plastic, inelastic deformation was less than expected given the strength of the recorded ground accelerations. For steel buildings designed to withstand earthquake loading, a design philosophy is to have some structural elements deform plastically, absorbing energy in the process. Typically elements of beams are designed to plastically deform while the columns remain elastic. In the earthquake some of these elements deformed plastically and the buildings were structurally undamaged. The question which then arises is; the building may be safe, but will it withstand a further severe earthquake? In other words how much further plastic work damage can be absorbed without failure of the structural element? Previous research at Auckland on modern structural steel, where the steel was prestrained various levels, to represent earthquake loading, the toughness was determined, as a function of prestrain for the naturally strain-aged steel. Further research, on the same steel, investigated life to failure for cyclic plastic straining in tension and compression loading at various plastic strain amplitudes. This work has shown that provided the plastic strain in the structural element is in the range 2 – 5% the steel will still meet the relevant NZ Standards. To determine the remaining life the plastic strain must be determ ined then the decision made; to use the building as is, replace the structural element or demolish.

The Experimental Research and Contrastive Analysis on the Attachments of Semi-Rigid Nodes in the Beam-Column T-Typed Member and End Plate of Steel Frame

2011 ◽  
Vol 243-249 ◽  
pp. 1163-1167
Author(s):  
Zhen Xing Gao ◽  
Ling Xu
Keyword(s):  
Bearing Capacity ◽  
Experimental Research ◽  
Steel Structures ◽  
Steel Frame ◽  
Contrastive Analysis ◽  
Experimental Basis ◽  
End Plate ◽  
The Ideal ◽  
Design And Application

Based on the connection tests of the semi-rigid nodes in the beam-column T-typed member and end plate of steel frame, this paper analyzes the failure phenomena, stiffness, bearing capacity and flexibility of two types of attachments. And according to the tests results, it compares the two types of attachments each other and proposes that T-typed member is a better type of attachment on its bearing capacity and flexibility. Therefore, it provides the experimental basis for the ideal design and application of attachments among the semi-rigid nodes in steel structures.

Seismic design of steel buildings: lessons from the 1995 Hyogo-ken Nanbu earthquake

1996 ◽  
Vol 23 (3) ◽  
pp. 727-756 ◽  
Author(s):  
Robert Tremblay ◽  
Andre Filiatrault ◽  
Michel Bruneau ◽  
Masayoshi Nakashima ◽  
Helmut G. L. Prion ◽  
...  
Keyword(s):  
Seismic Design ◽  
Steel Structures ◽  
Structural Systems ◽  
Braced Frames ◽  
Steel Buildings ◽  
Concentrically Braced Frames ◽  
Framed Structures ◽  
Concentrically Braced ◽  
Moment Resisting ◽  
Column Bases

Past and current seismic design provisions for steel structures in Japan are presented and compared with Canadian requirements. The performance of steel framed structures during the January 17, 1995, Hyogo-ken Nanbu earthquake is described. Numerous failures and examples of inadequate behaviour could be observed in buildings of various ages, sizes, and heights, and braced with different structural systems. In moment resisting frames, the damage included failures of beams, columns, beam-to-column connections, and column bases. Fracture of bracing members or their connections was found in concentrically braced frames. The adequacy of the current Canadian seismic design provisions is examined in view of the observations made. Key words: earthquake, seismic design, steel structures.

scholarly journals PENERAPAN METODE PROFILE MATCHING DALAM MEREKOMENDASIKAN BIBIT KELAPA SAWIT

2019 ◽  
Vol 3 (1) ◽  
Author(s):  
Ika Septi Mahdia ◽  
Solikhun Solikhun ◽  
M. Fauzan
Keyword(s):  
Decision Support ◽  
Decision Support System ◽  
Palm Oil ◽  
Support System ◽  
Oil Palm ◽  
Seed Selection ◽  
Matching Method ◽  
Profile Matching ◽  
Structured Problems ◽  
Plantation Crops

Oil palm plants are plantation crops that are cultivated and require intensive care, oil palm seeds are a major factor in the success of oil palm plantation cultivation. Quality palm oil seedlings will provide satisfactory yields, oil palm seedlings should be obtained with superior seed selection and good maintenance, in nurseries carried out by following the existing stages, oil palm plantations are long-term business and maintenance of oil palm seeds must be be considered and managed with incentives to ensure optimal production and business results in the future. This study aims to determine quality oil palm seeds in PTPN IV Bah Jambi Plantation. In the nursery is carried out by following the existing stage, this research uses Decision Support System (SPK) Profile Matching method. This method can be used to solve semi-structured problems by calculating consistency using the Profile Matching method, if consistent values are generated consistently can be used as a reference for ranking quality oil palm seeds in PTPN IV Bahjambi Plantation. For the results of the research it can be produced that it is easier to recommend oil palm seedlings and be an input to the plantation in recommending the best oil palm seeds.Keywords: Palm oil seeds, Decision Support System, Profile Matching

scholarly journals STUDY OF THE UTILIZATION OF PALM OIL INDUSTRY LIQUID WASTE

Konversi ◽  
2021 ◽  
Vol 10 (1) ◽  
Author(s):  
An Nisa Fitria ◽  
Vandhie Satyawira Gunawan ◽  
Mardiah Mardiah
Keyword(s):  
Palm Oil ◽  
Oil Palm ◽  
Economic Value ◽  
Liquid Waste ◽  
Oil Industry ◽  
Fresh Fruit ◽  
Added Value ◽  
Palm Fruit ◽  
Fresh Fruit Bunches ◽  
Plantation Crops

Palm oil is one of the plantation crops that have high economic value and is growing rapidly. The wider the area of oil palm plantations in Indonesia, the more palm oil mills will process palm fresh fruit marks and produce waste from processed palm oil, namely solid waste and liquid waste. Each tonne of fresh fruit bunches (FFB) processed at the plant will potentially leave waste of about 23% empty palm oil, 4% wet decanter solid, 6.5% shell, 13% fiber, and 50% liquid waste. This review will discuss the utilization of palm oil mill liquid waste (LCPKS) which is organic material that still contains many benefits such as nutrients, therefore the application of liquid waste is an effort to recycle some of the nutrients (recycling nutrients) which is followed by harvesting fresh fruit bunches (FFB) from oil palm so that it will reduce the cost of fertilization which is classified as very high for oil palm cultivation. During the processing of oil palm fruit into palm oil in the palm oil industry, the remaining process is obtained in the form of liquid waste. If done properly, the liquid waste of the palm oil industry is considerable potential and can increase the added value of waste itself.Keywords: liquid waste industry, palm oil, utilization  

Sign in / Sign up

Export Citation Format

Share Document