scholarly journals An Experimental Investigation on the Behavior of Strain Hardening Cement-Based Composites (SHCC) under Impact Compression and Shear Loading

2020 ◽  
Author(s):  
Ali A. Heravi ◽  
Oliver Mosig ◽  
Ahmed Tawfik ◽  
Manfred Curbach ◽  
Viktor Mechtcherine
Keyword(s):  
Shear Strength ◽  
Strain Hardening ◽  
Failure Modes ◽  
Split Hopkinson Pressure Bar ◽  
Tensile Load ◽  
High Energy ◽  
Shear Loading ◽  
Impact Compression ◽  
Split Hopkinson ◽  
The Impact

The ductile behavior of strain hardening cement-based composites (SHCC) under direct tensile load makes them promising solutions for applications where high energy dissipation is needed, such as earthquake, impact by a projectile, or blast. However, the superior tensile ductility of SHCC due to multiple cracking does not necessarily entail compressive and shear ductility. As an effort to characterize the behavior of SHCC under impact compressive and shear loading, relevant to the mentioned high-speed loading scenarios, the paper at hand studies the performance of a SHCC and its constituent cement-based matrices using the split-Hopkinson bar method. For compression experiments, cylindrical specimens with a length-to-diameter ratio (l/d) of 1.6 were used. The selected length of the sample led to similar failure modes under the quasi-static and impact loading conditions, which was necessary for a reliable comparison of the obtained compressive strengths. The impact experiments were performed in a split-Hopkinson pressure bar (SHPB) at a strain rate that reached 110 s-1 at the moment of failure. For shear experiments, a special adapter was developed for a split-Hopkinson tension bar (SHTB). The adapter enabled performing impact shear experiments on planar specimens using the tensile wave generated in the SHTB. Results showed a dynamic increase factor (DIF) of 2.3 and 2.0 for compressive and shear strength of SHCC, respectively. As compared to the non-reinforced constituent matrix, the absolute value of the compressive strength was lower for the SHCC. Contrarily, under shear loading, the SHCC yielded the higher shear strength than the non-reinforced matrix.

scholarly journals An Experimental Investigation of the Behavior of Strain-Hardening Cement-Based Composites (SHCC) under Impact Compression and Shear Loading

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4514
Author(s):  
Ali A. Heravi ◽  
Oliver Mosig ◽  
Ahmed Tawfik ◽  
Manfred Curbach ◽  
Viktor Mechtcherine
Keyword(s):  
Shear Strength ◽  
Strain Hardening ◽  
Failure Modes ◽  
Split Hopkinson Pressure Bar ◽  
Tensile Load ◽  
High Energy ◽  
Shear Loading ◽  
Impact Compression ◽  
Split Hopkinson ◽  
The Impact

The ductile behavior of strain-hardening cement-based composites (SHCC) under direct tensile load makes them promising solutions in applications where high energy dissipation is needed, such as in earthquakes, impacts by projectiles, or blasts. However, the superior tensile ductility of SHCC due to multiple cracking does not necessarily point to compressive and shear ductility. As an effort to characterize the behavior of SHCC under impact compressive and shear loading relevant to the aforementioned high-speed loading scenarios, the paper at hand studies the performance of a particular SHCC and its constituent, cement-based matrices using the split-Hopkinson bar method. For compression experiments, cylindrical specimens with a length-to-diameter ratio (l/d) of 1.6 were used. The selected length of the sample led to similar failure modes under quasi-static and impact loading conditions, necessary to a reliable comparison of the observed compressive strengths. The impact experiments were performed in a split-Hopkinson pressure bar (SHPB) at a strain rate that reached 110 s−1 at the moment of failure. For shear experiments, a special adapter was developed for a split-Hopkinson tension bar (SHTB). The adapter enabled impact shear experiments to be performed on planar specimens using the tensile wave generated in the SHTB. Results showed dynamic increase factors (DIF) of 2.3 and 2.0 for compressive and shear strength of SHCC, respectively. As compared to the non-reinforced constituent matrix, the absolute value of the compressive strength was lower for the SHCC. Contrarily, under shear loading, the SHCC demonstrated higher shear strength than the non-reinforced matrix.

scholarly journals Research On Water-Immersion Softening Mechanism of Coal Rock Mass Based on Split Hopkinson Pressure Bar Experiment

2021 ◽  
Author(s):  
Zhiyuan Liu ◽  
Gang Wang ◽  
Jinzhou Li ◽  
Huaixing Li ◽  
Haifeng Zhao ◽  
...  
Keyword(s):  
Moisture Content ◽  
Coal Sample ◽  
Split Hopkinson Pressure Bar ◽  
Water Immersion ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
Impact Compression ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
The Impact

Abstract The coal mining process is affected by multiple sources of water such as groundwater and coal seam water injection. Understanding the dynamic mechanical parameters of water-immersed coal is helpful to the safe production of coal mines. The impact compression tests were performed on coal with different moisture contents by using the ϕ50 mm Split Hopkinson Pressure Bar (SHPB) experimental system, and the dynamic characteristics and energy loss laws of water-immersed coal with different compositions and water contents were analyzed. Through analysis and discussion, it is found that: (1) When the moisture content of the coal sample is 0%, 30%, 60%, the stress, strain rate and energy first increase and then decrease with time; (2) When the moisture content of the coal sample increases from 30% to 60%, the stress "plateau" of the coal sample disappears, resulting in an increase in the interval of the compressive stress and a decrease in the interval of the expansion stress. (3) The increase of the moisture content of the coal sample will affect its impact deformation and failure mode. When the moisture content is 60%, the incident rod end and the transmission rod end of the coal sample will have obvious compression failure, and the middle part of the coal sample will also experience expansion and deformation. (4) The coal composition ratio suitable for the impact experiment of coal immersion softening is optimized.

Analysis of the Impact of the Frequency Range of the Tensometer Bridge and Projectile Geometry on the Results of Measurements by the Split Hopkinson Pressure Bar Method

2013 ◽  
Vol 20 (4) ◽  
pp. 555-564 ◽  
Author(s):  
Wojciech Moćko
Keyword(s):  
Test Bench ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Deformation ◽  
Spectral Width ◽  
Hopkinson Pressure Bar ◽  
Computing Environment ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
The Impact ◽  
Bench Model

Abstract The paper presents the results of the analysis of the striker shape impact on the shape of the mechanical elastic wave generated in the Hopkinson bar. The influence of the tensometer amplifier bandwidth on the stress-strain characteristics obtained in this method was analyzed too. For the purposes of analyzing under the computing environment ABAQUS / Explicit the test bench model was created, and then the analysis of the process of dynamic deformation of the specimen with specific mechanical parameters was carried out. Based on those tests, it was found that the geometry of the end of the striker has an effect on the form of the loading wave and the spectral width of the signal of that wave. Reduction of the striker end diameter reduces unwanted oscillations, however, adversely affects the time of strain rate stabilization. It was determined for the assumed test bench configuration that a tensometric measurement system with a bandwidth equal to 50 kHz is sufficient

scholarly journals Evaluation of Energy Absorption Capabilities of Polyethylene Foam under Impact Deformation

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3613
Author(s):  
Baohui Yang ◽  
Yangjie Zuo ◽  
Zhengping Chang
Keyword(s):  
Energy Absorption ◽  
Failure Modes ◽  
High Strain ◽  
Early Stage ◽  
High Energy ◽  
Test Method ◽  
Test Theory ◽  
Strain Rates ◽  
Impact Properties ◽  
The Impact

Foams are widely used in protective applications requiring high energy absorption under impact, and evaluating impact properties of foams is vital. Therefore, a novel test method based on a shock tube was developed to investigate the impact properties of closed-cell polyethylene (PE) foams at strain rates over 6000 s−1, and the test theory is presented. Based on the test method, the failure progress and final failure modes of PE foams are discussed. Moreover, energy absorption capabilities of PE foams were assessed under both quasi-static and high strain rate loading conditions. The results showed that the foam exhibited a nonuniform deformation along the specimen length under high strain rates. The energy absorption rate of PE foam increased with the increasing of strain rates. The specimen energy absorption varied linearly in the early stage and then increased rapidly, corresponding to a uniform compression process. However, in the shock wave deformation process, the energy absorption capacity of the foam maintained a good stability and exhibited the best energy absorption state when the speed was higher than 26 m/s. This stable energy absorption state disappeared until the speed was lower than 1.3 m/s. The loading speed exhibited an obvious influence on energy density.

scholarly journals Blasting-Induced Permeability Enhancement of Ore Deposits Associated with Low-Permeability Weakly Weathered Granites Based on the Split Hopkinson Pressure Bar

Geofluids ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Lei Yan ◽  
Wenhua Yi ◽  
Liansheng Liu ◽  
Jiangchao Liu ◽  
Shenghui Zhang
Keyword(s):  
Split Hopkinson Pressure Bar ◽  
Deformation Modulus ◽  
Constant Speed ◽  
Initial Porosity ◽  
Peak Strain ◽  
Variable Speed ◽  
Hopkinson Pressure Bar ◽  
Impact Compression ◽  
Split Hopkinson ◽  
Pressure Bar

By utilizing the improved split Hopkinson pressure bar (SHPB) test device, uniaxial, constant-speed cyclic, and variable-speed cyclic impact compression tests were conducted on weakly weathered granite samples. By combining nuclear magnetic resonance (NMR) and triaxial seepage tests, this study investigated the change laws in the mechanical properties, porosity evolution, and permeability coefficients of the samples under cyclic impacts. The results showed that in constant-speed cyclic impacts with increasing impact times, deformation modulus decreased, whilst porosity firstly decreased and then increased. Furthermore, dynamic peak strength firstly increased and then decreased whereas peak strain constantly increased before failure of the samples. In the variable-speed cyclic impacts, as impact times increased, deformation modulus firstly increased and then declined with damage occurring after four impact times. The compaction process weakened and even disappeared with increasing initial porosity. Three types of pores were found in the samples that changed in multiscale under cyclic loading. In general, small pores extended to medium- and large-sized pores. After three variable-speed cyclic impacts, the porosity of the samples was larger than the initial porosity and the permeability coefficient was greater than its initial value. The results demonstrate that the purpose of enhancing permeability and keeping the ore body stable can be achieved by conducting three variable-speed cyclic impacts on the samples.

Experimental and Numerical Researches of Dynamic Failure of a High Strength Alumina/Boride Ceramic Composite

2008 ◽  
Vol 368-372 ◽  
pp. 713-716 ◽  
Author(s):  
Jiang Tao Zhang ◽  
Li Sheng Liu ◽  
Peng Cheng Zhai ◽  
Qing Jie Zhang
Keyword(s):  
Ceramic Composite ◽  
Failure Modes ◽  
Split Hopkinson Pressure Bar ◽  
Numerical Models ◽  
High Strength ◽  
Tensile Failure ◽  
Hopkinson Pressure Bar ◽  
Loading Direction ◽  
Split Hopkinson ◽  
Pressure Bar

The dynamic compressive behavior of Al2O3 (10% vol.) / TiB2 ceramic composite had been tested by using a split Hopkinson pressure bar in this paper. The results show that the main failure modes of the ceramic composite include crushed failure and split fracture along the loading direction. The former is the typical compressive failure of brittle materials. The later is tensile failure along the flaws produced during the composite manufacturing. The numerical simulation was also used to study the effect of the diameter/length ratio of the samples on the experimental results. The effect of the deformation in the bars’ ends, which contacted with the samples, was also studied in the numerical models.

scholarly journals Analysis of Fractal and Energy Consumption Characteristics of Concrete under Impact Loading

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Yutao Li ◽  
Faning Dang ◽  
Mei Zhou ◽  
Jie Ren
Keyword(s):  
Fractal Dimension ◽  
Surface Energy ◽  
Failure Modes ◽  
Crack Surface ◽  
Split Hopkinson Pressure Bar ◽  
Utilization Rate ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
Impact Compression ◽  
Aggregate Rate

In order to study the compressive deformation and energy evolution characteristics of concrete under dynamic loading, impact compression tests with impact velocities of 5, 6, and 7 m/s were carried out on concrete samples with aggregate volume ratios of 0, 32%, 37%, and 42%, respectively, using a split Hopkinson pressure bar test apparatus. The broken concrete pieces after destruction were collected and arranged. The fractal characteristics of fragmentation distribution of concrete specimens with different aggregate rates under impact were discussed, and the roughness of the fragment surface was characterized by the fractal dimension of the broken fragment and the crack surface energy was calculated. In addition, the analytical equation of the fractal dimension of the broken fragment and the crack surface energy was established. The relationship between the specimen energy absorption and the crack surface energy was compared and analyzed. The results show that the concrete specimens are mainly tensile split failure modes under different impact speeds. The fractal dimension, absorption energy, and crack surface energy all increase with the increase in impact speed and decrease with the increase in the aggregate rate. When the aggregate rate is different, the effective utilization rate of the absorbed energy is the largest when the aggregate content is 37%. The surface energy of the crack can be used to estimate the concrete dynamic intensity.

Impact Resistance of SM Joints Formed With ICA

2002 ◽  
Vol 124 (4) ◽  
pp. 374-378 ◽  
Author(s):  
C. M. Lawrence Wu ◽  
Robert K. Y. Li ◽  
N. H. Yeung
Keyword(s):  
Impact Damage ◽  
Impact Resistance ◽  
High Energy ◽  
Bending Test ◽  
Conductive Adhesives ◽  
Energy Impact ◽  
Split Hopkinson ◽  
Post Impact ◽  
Impact Bending ◽  
The Impact

Isotropic conductive adhesives (ICA) have been considered as replacement materials for lead-tin solder alloys. In this paper, the post-impact shear strength of ICA surface mount (SM) joints was obtained experimentally and compared with that of SM lead-tin joints. The dynamic impact energy was provided in the form of three-point bending on the PCB using equipment called the split Hopkinson bar. Strain rates of over 4000/s were used for the impact bending test. The action of impact bending was used to simulate the effect on the PCB and the interconnection as a result of high energy impact on an electronic equipment. Shear test was then performed to examine the change in strength of the ICA joints as a result of impact damage. It was found that the SM ICA joints failed due to impact at a strain rate just over 4000/s. Microstructural examination carried out using a scanning electron microscope revealed that the interface between the ICA and copper pad on the PCB was the weakest region of the joint.

scholarly journals Large Deformation Behavior of High Strength Steel Under Extreme Loading Conditions: High Temperature and High Strain Rate Experiments and Modeling

2018 ◽  
Vol 183 ◽  
pp. 01053
Author(s):  
Xueyang Li ◽  
Christian C. Roth ◽  
Dirk Mohr
Keyword(s):  
Strain Hardening ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
High Strength ◽  
Fracture Initiation ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
Temperature Dependent ◽  
Split Hopkinson ◽  
Pressure Bar

Plasticity and fracture experiments are carried out on flat smooth and notched tensile specimens extracted from DP800 steel sheets. A split Hopkinson pressure bar testing system equipped with a load inversion device is utilized to reach high strain rates. Temperature dependent experiments ranging from 20°C to 300°C are performed at quasi-static strain rates. The material exposes a monotonic strain hardening behaviour with a non-monotonic temperature dependency. The rate-independent material behaviour at room-temperature is described with a non-associated Hill’48 plasticity model and an Swift-Voce strain hardening. A machine learning based model is used multiplicatively to capture the rate and temperature responses. A good agreement between measured and simulated force-displacement curves as well as local surface is obtained. The loading paths to fracture are then extracted to facilitate further development of a temperature dependent fracture initiation model.

Analysis of Failure Patterns and Damage Mechanisms under Impact Compression of Hybrid Fiber Reinforced Concrete

2012 ◽  
Vol 193-194 ◽  
pp. 609-613
Author(s):  
Meng Chen ◽  
Zhi Li ◽  
Zhe An Lu
Keyword(s):  
Reinforced Concrete ◽  
Failure Modes ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Hybrid Fiber ◽  
Impact Compression ◽  
Failure Patterns ◽  
Compression Properties

In order to studying the failure patterns under impact compression of Hybrid Fiber Reinforced Concrete(HFRC), tests focused on static and dynamic compression properties according to steel fiber reinforced concrete(SFRC) and HFRC are adopted. The equipment of dynamic compression properties test is Ф74mm split Hopkinson pressure bar (SHPB). The static and dynamic compressive strength at four different strain rates of the two materials are obtained, while failure mechanism has been analyzed from specimens’ failure modes in static and dynamic compressive tests, which in turn provides theory basis for the application of HFRC.

Sign in / Sign up

Export Citation Format

Share Document