scholarly journals Potential Use of Alkaline-Activated Indonesian Pumice Powder as Lead Adsorbent in Solution System

2019 ◽  
Vol 16 (2) ◽  
pp. 203
Author(s):  
Faridlotul Hasanah ◽  
Syaiful Anwar ◽  
Arief Hartono ◽  
Untung Sudadi
Keyword(s):  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Low Cost ◽  
Physicochemical Characteristics ◽  
Maximum Adsorption Capacity ◽  
Lead Removal ◽  
Isothermal Adsorption ◽  
Adsorption Models ◽  
Volcanic Material ◽  
Potential Use

<p>Pumice is a volcanic material that found abundant in Indonesia. Owing to its physicochemical characteristics it can be utilized as a low-cost natural adsorbent for cationic contaminants. This study aimed to assess the performances of adsorbents prepared from NaOH-activated powder of Lombok and Kediri pumices for lead removal in solution systems based on their maximum adsorption capacity and removal efficiency parameters. The adsorption tests were done in batch experimentation using pumice powder of 74 μm particle size activated with 0.5, 1, and 2 <em>M</em> NaOH and lead solutions with initial concentrations of 0-260 mg.L<sup>-1</sup>. The most favorable NaOH activation concentration for both pumices was 0.5 <em>M </em>which resulted from Lombok pumice prepared-adsorbent with Pb maximum adsorption capacity based on linearized conventional and rearranged Langmuir isothermal adsorption models of 236.4 and 186.3 mg.g<sup>-1</sup>, while those of Kediri pumice were of 218.4 and 210.8 mg.g<sup>-1</sup>, respectively. The removal efficiency of both adsorbents were &gt;80% at the initial Pb concentration of &lt;100 mg.L<sup>-1 </sup>and around 50-80% at 100-260 mg.L<sup>-1</sup>. Both pumices are therefore considered potential to be utilized as an adsorbent for cationic contaminants in solution systems with reliable performances.</p>

Adsorption and Catalysis of Orange II from Wastewater by Inorganic-Organic-Bentonite

2011 ◽  
Vol 340 ◽  
pp. 236-240
Author(s):  
Jian Feng Ma ◽  
Jian Ming Yu ◽  
Bing Ying Cui ◽  
Ding Long Li ◽  
Juan Dai
Keyword(s):  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Dye Removal ◽  
Maximum Adsorption Capacity ◽  
Orange Ii ◽  
Acid Dye ◽  
Secondary Pollution ◽  
Organic Bentonite ◽  
Maximum Removal

Inorganic-organic-bentonite was synthesized by modification of bentonite by Hydroxy-iron and surfactant, which could be applied in dye removal by adsorption and catalysis. The removal of acid dye Orange II was studied at various factors such as time and pH of solution. The results showed that the inorganic-organic-bentonite could efficiently remove the dye with efficiency of 96.22%. The maximum adsorption capacity is 76 mg/g. The pH of solution has significant effect on both adsorption and catalysis. When pH was 4, the maximum removal efficiency of adsorption and catalysis were 97.57% and 87.23%, respectively. After degradation, the secondary pollution was diminished and the bentonite could be reused.

scholarly journals Removal of Chromium(III) and Cadmium(II) Heavy Metal Ions from Aqueous Solutions Using Treated Date Seeds: An Eco-Friendly Method

Molecules ◽  
2021 ◽  
Vol 26 (12) ◽  
pp. 3718
Author(s):  
Mohammad Azam ◽  
Saikh Mohammad Wabaidur ◽  
Mohammad Rizwan Khan ◽  
Saud I. Al-Resayes ◽  
Mohammad Shahidul Islam
Keyword(s):  
Metal Ions ◽  
Adsorption Capacity ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
Surface Analysis Techniques ◽  
Adsorption Processes ◽  
Ft Ir ◽  
Metal Elution ◽  
Date Pits

The aim of the research was to prepare low-cost adsorbents, including raw date pits and chemically treated date pits, and to apply these materials to investigate the adsorption behavior of Cr(III) and Cd(II) ions from wastewater. The prepared materials were characterized using SEM, FT-IR and BET surface analysis techniques for investigating the surface morphology, particle size, pore size and surface functionalities of the materials. A series of adsorption processes was conducted in a batch system and optimized by investigating various parameters such as solution pH, contact time, initial metal concentrations and adsorbent dosage. The optimum pH for achieving maximum adsorption capacity was found to be approximately 7.8. The determination of metal ions was conducted using atomic adsorption spectrometry. The experimental results were fitted using isotherm Langmuir and Freundlich equations, and maximum monolayer adsorption capacities for Cr(III) and Cd(II) at 323 K were 1428.5 and 1302.0 mg/g (treated majdool date pits adsorbent) and 1228.5 and 1182.0 mg/g (treated sagai date pits adsorbent), respectively. It was found that the adsorption capacity of H2O2-treated date pits was higher than that of untreated DP. Recovery studies showed maximal metal elution with 0.1 M HCl for all the adsorbents. An 83.3–88.2% and 81.8–86.8% drop in Cr(III) and Cd(II) adsorption, respectively, were found after the five regeneration cycles. The results showed that the Langmuir model gave slightly better results than the Freundlich model for the untreated and treated date pits. Hence, the results demonstrated that the prepared materials could be a low-cost and eco-friendly choice for the remediation of Cr(III) and Cd(II) contaminants from an aqueous solution.

scholarly journals Adsorption Study of Cu2+ Ions from Aqueous Solutions by Bael Flowers (Aegle marmelos)

2020 ◽  
Vol 11 (4) ◽  
pp. 11891-11904
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Metal Ion ◽  
Low Cost ◽  
Sem Analysis ◽  
Ion Concentration ◽  
Maximum Adsorption Capacity ◽  
Aegle Marmelos ◽  
Batch Mode ◽  
Initial Ph

In the present study, batch mode adsorption was carried out to investigate the adsorption capacity of dried bael flowers (Aegle marmelos) for the adsorptive removal of Cu(II) ions from aqueous solutions by varying agitation time, initial metal concentration, the dose of adsorbent, temperature, and initial pH of the Cu(II) ion solution. The percentage removal of 98.7% was observed at 50 ppm initial metal ion concentration, 0.5 g/100.00 cm3 adsorbent dosage, within the contact time of 120 minutes at 30 ºC in the pH range of 4 – 7. The sorption processes of Cu(II) ions was best described by pseudo-second-order kinetics. Langmuir isotherm had a good fit with the experimental data with 0.97 of correlation coefficient (R2), and the maximum adsorption capacity obtained was 23.14 mg g-1 at 30 ºC. The results obtained from sorption thermodynamic studies suggested that the adsorption process is exothermic and spontaneous. SEM analysis showed tubular voids on the adsorbent. FTIR studies indicated the presence of functional groups like hydroxyl, –C-O, –C=O, and amide groups in the adsorbent, which can probably involve in metal ion adsorption. Therefore, dried bael flowers can be considered an effective low-cost adsorbent for treating Cu(II) ions.

Insights into the mechanism of methylene blue removed by novel and classic biochars

2019 ◽  
Vol 79 (8) ◽  
pp. 1561-1570
Author(s):  
Wei Chen ◽  
Fengting Chen ◽  
Bin Ji ◽  
Lin Zhu ◽  
Hongjiao Song
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Low Cost ◽  
Underlying Mechanism ◽  
Maximum Adsorption Capacity ◽  
Experimental Conditions ◽  
Average Pore ◽  
Adsorption Effect ◽  
Magnolia Grandiflora

Abstract The adsorption behavior and the underlying mechanism of methylene blue (MB) sorption on biochars prepared from different feedstocks at 500 °C were evaluated. The biochar feedstocks included Magnolia grandiflora Linn. leaves biochar (MBC), pomelo (Citrus grandis) peel biochar (PBC) and badam shell biochar (BBC). The results of characterizing and analyzing the samples showed that different biochars had different effects on the adsorption of MB. It could be found that MBC had the best adsorption effect on MB due to its largest average pore diameter of 5.55 nm determined by Brunauer-Emmett-Teller analysis. Under the optimal conditions, the maximum adsorption capacities of BBC, PBC and MBC were 29.7, 85.15 and 99.3 mg/g, respectively. The results showed that the amount of adsorption was affected by the pH value. The maximum adsorption capacity of MBC was 46.99 mg/g when it was at pH of 3, whereas for the same experimental conditions the maximum adsorption capacity of BBC and PBC was 25.29 mg/g at pH of 11 and 36.08 mg/g at pH of 7, respectively. Therefore, MBC was found to be a most efficient low-cost adsorbentl for dye wastewater treatment compared with BBC and PBC, and it had the best removal effect under acidic conditions.

Potential of Agricultural Waste Material (Ananas cosmos) as Biosorbent for Heavy Metal Removal in Polluted Water

2020 ◽  
Vol 1010 ◽  
pp. 489-494
Author(s):  
Abdul Hafidz Yusoff ◽  
Rosmawani Mohammad ◽  
Mardawani Mohamad ◽  
Ahmad Ziad Sulaiman ◽  
Nurul Akmar Che Zaudin ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Adsorption Capacity ◽  
Metal Removal ◽  
Low Cost ◽  
Agricultural Waste ◽  
Heavy Metal Removal ◽  
Polluted Water ◽  
Maximum Adsorption Capacity ◽  
Pineapple Peel

Conventional methods to remove heavy metals from polluted water are expensive and not environmentally friendly. Therefore, this study was carried out to investigate the potential of agricultural waste such as pineapple peel (Ananas Cosmos) as low-cost absorbent to remove heavy metals from synthetic polluted water. The results showed that Cd, Cr and Pb were effectively removed by the biosorbent at 12g of pineapple peels in 100 mL solution. The optimum contact time for maximum adsorption was found to be 90 minutes, while the optimum pH for the heavy metal’s adsorption was 9. It was demonstrated that with the increase of adsorbent dosage, the percent of heavy metals removal was also increased due to the increasing adsorption capacity of the adsorbent. In addition, Langmuir model show maximum adsorption capacity of Cd is 1.91 mg/g. As conclusions, our findings show that pineapple peel has potential to remove heavy metal from polluted water.

scholarly journals Effects of Cu(II) on the Adsorption Behaviors of Cr(III) and Cr(VI) onto Kaolin

2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Juanjuan Liu ◽  
Xiaolong Wu ◽  
Yandi Hu ◽  
Chong Dai ◽  
Qin Peng ◽  
...  
Keyword(s):  
Distribution Coefficient ◽  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Saturation Index ◽  
Surface Complexation ◽  
Maximum Adsorption Capacity ◽  
Positive Correlation ◽  
Adsorption Sites ◽  
Ph Values ◽  
Adsorption Behaviors

The adsorption of Cr(III) or Cr(VI) in the absence and presence of Cu(II) onto kaolin was investigated under pH 2.0–7.0. Results indicated that the adsorption rate was not necessarily proportional to the adsorption capacity. The solutions’ pH values played a key role in kaolin zeta potential(ζ), especially the hydrolysis behavior and saturation index of heavy metal ions. In the presence of Cu(II),qmixCr(III)reached the maximum adsorption capacity of 0.73 mg·g−1at pH 6.0, while the maximum adsorption capacity for the mixed Cr(VI) and Cu(II) system (qmixCr(VI)) was observed at pH 2.0 (0.38 mg·g−1). Comparing the adsorption behaviors and mechanisms, we found that kaolin prefers to adsorb hydrolyzed products of Cr(III) instead of Cr3+ion, while adsorption sites of kaolin surface were occupied primarily by Cu(II) through surface complexation, leading to Cu(II) inhibited Cr(VI) adsorption. Moreover, Cr(III) and Cr(VI) removal efficiency had a positive correlation with distribution coefficientKd. Cr(III) and Cr(VI) removal efficiency had a positive correlation with distribution coefficientKdand that of adsorption affinities of Cr(III) or Cr(VI) on kaolin was found to beKdCr(III) <KdCr(III)-Cu(II) andKdCr(VI) >KdCr(VI)-Cu(II).

Equilibrium, kinetic and thermodynamic studies of mercury adsorption on almond shell

2012 ◽  
Vol 65 (8) ◽  
pp. 1341-1349 ◽  
Author(s):  
Shokooh Sadat Khaloo ◽  
Amir Hossein Matin ◽  
Sahar Sharifi ◽  
Masoumeh Fadaeinia ◽  
Narges Kazempour ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Low Cost ◽  
Second Order ◽  
Ion Concentration ◽  
Physical Parameters ◽  
Maximum Adsorption Capacity ◽  
Almond Shell ◽  
Pseudo Second Order ◽  
Uptake Process ◽  
Reaction Equations

The application of almond shell as a low cost natural adsorbent to remove Hg2+ from aqueous solution was investigated. Batch experiments were carried out to evaluate the adsorption capacity of the material. The chemical and physical parameters such as pH, sorbent amount, initial ion concentration, and contact time were optimized for the maximum uptake of mercury onto the solid surface. Adsorption isotherms were expressed by Langmuir and Freundlich adsorption models, and the experimental data were found to fit the Langmuir model rather than the Freundlich. The maximum adsorption capacity obtained from the Langmuir isotherm was 135.13 mg/g. A kinetic study was carried out with pseudo-first-order and pseudo-second-order reaction equations and it was found that the Hg2+ uptake process followed the pseudo-second-order rate expression. The thermodynamic values, ΔG0, ΔH0 and ΔS0, indicated that adsorption was an endothermic and spontaneous process. The potential of this material for mercury elimination was demonstrated by efficient Hg2+ removal from a synthetic effluent.

scholarly journals Investigation of kinetics and adsorption isotherm for fluoride removal from aqueous solutions using mesoporous cerium–aluminum binary oxide nanomaterials

RSC Advances ◽  
2021 ◽  
Vol 11 (46) ◽  
pp. 28744-28760
Author(s):  
Rumman Zaidi ◽  
Saif Ullah Khan ◽  
I. H. Farooqi ◽  
Ameer Azam
Keyword(s):  
Adsorption Isotherm ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Removal Efficiency ◽  
Small Dose ◽  
Binary Oxide ◽  
Fluoride Removal ◽  
Maximum Adsorption Capacity

Mesoporous Ce–Al binary oxide nanomaterials prepared with a surface area of 110.32 m2 g−1 showed defluoridation capacity at pH 2.4, exhibited maximum adsorption capacity of 384.6 mg g−1 and a removal efficiency of 91.5% at a small dose of nanoadsorbent.

scholarly journals H-Clinoptilolite as an Efficient and Low-Cost Adsorbent for Batch and Continuous Gallium Removal from Aqueous Solutions

2021 ◽  
Author(s):  
P. Sáez ◽  
A. Rodríguez ◽  
J. M. Gómez ◽  
C. Paramio ◽  
C. Fraile ◽  
...  
Keyword(s):  
Particle Size ◽  
Adsorption Capacity ◽  
Low Cost ◽  
Fixed Bed ◽  
Particle Size Effect ◽  
Breakthrough Curves ◽  
Maximum Adsorption Capacity ◽  
Fixed Bed Column ◽  
Gallium Concentration ◽  
Best Fit

AbstractIn this paper, the gallium (III) ions’ adsorption onto protonated clinoptilolite (H-CLP) was investigated both in batch and fixed-bed column experiments. Regarding batch experiments, the influence of some parameters such as adsorbent dosage, size particle, and temperature was studied, determining that a dosage of 10 g/L for an initial pollutant concentration of 40 mg/L leads to a removal percentage over 85% regardless of particle size and temperature. On the other hand, adsorption of gallium onto H-CPL is an endothermic and spontaneous process in the studied temperature range, concluding that the maximum adsorption capacity was 16 mg/g for 60 °C. Concerning to the effect of the presence of other cations in solution, such as Na+, K+, or Ca2+, gallium adsorption capacity only drops by 20%, although the initial concentration of other cations in the solution is 50 times higher than gallium concentration. This means that clinoptilolite has a high affinity for gallium which can be very favorable for further selectivity tests. A crucial factor for this high selectivity could be the protonation of clinoptilolite which allows working without modifying the pH of the aqueous solution with acid. In the fixed-bed experiments, breakthrough curves were obtained, and the effect of operation variables was determined. A breakpoint value of 254 min for 64 g of adsorbent and flow rate of 9.0 mL/min (7.0 BV/h) were obtained, when treating a pollutant volume of 33 BV. Additionally, the breakthrough curves were fitted to different models to study the particle size effect, being the best fit corresponding to the Adams–Bohart model. This fact confirmed the influence of particle size on adsorption kinetics. Graphical Abstract

scholarly journals Highly Effective Covalently Crosslinked Composite Alginate Cryogels for Cationic Dye Removal

Gels ◽  
2021 ◽  
Vol 7 (4) ◽  
pp. 178
Author(s):  
Serap Sezen ◽  
Vijay Kumar Thakur ◽  
Mehmet Murat Ozmen
Keyword(s):  
Adsorption Capacity ◽  
Dye Removal ◽  
Low Cost ◽  
Dye Adsorption ◽  
Maximum Adsorption Capacity ◽  
High Porosity ◽  
Order Model ◽  
Removal Capacity ◽  
Pseudo Second Order ◽  
The One

Currently, macroporous hydrogels have been receiving attention in wastewater treatment due to their unique structures. As a natural polymer, alginate is used to remove cationic dyes due to its sustainable features such as abundance, low cost, processability, and being environmentally friendly. Herein, alginate/montmorillonite composite macroporous hydrogels (cryogels) with high porosity, mechanical elasticity, and high adsorption yield for methylene blue (MB) were generated by the one-step cryogelation technique. These cryogels were synthesized by adding montmorillonite into gel precursor, followed by chemical cross-linking employing carbodiimide chemistry in a frozen state. The as-prepared adsorbents were analyzed by FT-IR, SEM, gel fraction, swelling, uniaxial compression, and MB adsorption tests. The results indicated that alginate/montmorillonite cryogels exhibited high gelation yield (up to 80%), colossal water uptake capacity, elasticity, and effective dye adsorption capacity (93.7%). Maximum adsorption capacity against MB was 559.94 mg g−1 by linear regression of Langmuir model onto experimental data. The Pseudo-Second-Order model was fitted better onto kinetic data compared to the Pseudo-First-Order model. Improved porosity and mechanical elasticity yielding enhanced dye removal capacity make them highly potential alternative adsorbents compared to available alginate/montmorillonite materials for MB removal.

Sign in / Sign up

Export Citation Format

Share Document