Investigation on the Effect of Mud Additives on the Gelation Performance of PAM/PEI System for Lost Circulation Control

2021 ◽  
Author(s):  
Mohamed Shamlooh ◽  
Ahmed Hamza ◽  
Ibnelwaleed A. Hussein ◽  
Mustafa S. Nasser ◽  
Saeed Salehi
Keyword(s):  
Storage Modulus ◽  
Oil And Gas ◽  
Loss Modulus ◽  
Drilling Fluid ◽  
Gelation Time ◽  
Drilling Fluids ◽  
Lost Circulation ◽  
Reservoir Conditions ◽  
Induced Fractures ◽  
Wellbore Strengthening

Abstract Lost circulation is one of the most common problems in the drilling of oil and gas wells where mud escapes through natural or induced fractures. Lost circulation can have severe consequences from increasing the operational cost to compromising the stability of wells. Recently, polymeric formulations have been introduced for wellbore strengthening purposes where it can serve as Loss Circulation Materials (LCMs) simultaneously. Polymeric LCMs have the potential to be mixed with drilling fluids during the operation without stopping to avoid non-productive time. In this study, the significance of most common conventional mud additives and their impact on the gelation performance of Polyacrylamide (PAM) / Polyethyleneimine (PEI) has been investigated. Drilling fluid with typical additives has been designed with a weight of 9.6 ppg. Additives including bentonite, barite, CarboxyMethylCellulose (CMC), lignite, caustic soda, desco, and calcium carbonate has been studied individually and combined. Each additive is mixed with the polymeric formulation (PAM 9% PEI 1%) with different ratios, then kept at 130°C for 24 hrs. Rheological performance of the mature gel has been tested using parallel plate geometry, Oscillatory tests have been used to assess the storage Modulus and loss modulus. Moreover, the gelation profile has been tested at 500 psi with a ramped temperature to mimic the reservoir conditions to obtain the gelation time. The gelation time of the polymer-based mud was controllable by the addition of a salt retarder (Ammonium Chloride), where a gelation time of more than 2 hours could be achieved at 130°C. Laboratory observations revealed that bentonite and CMC have the most effect as they both assist in producing stronger gel. While bentonite acts as a strengthening material, CMC increases the crosslinking network. Bentonite has successfully increased the gel strength by 15% providing a storage modulus of up to 1150 Pa without affecting the gelation time. This work helps in better understanding the process of using polymeric formulations in drilling activities. It provides insights to integrate gelling systems that are conventionally used for water shut-off during the drilling operation to replace the conventional loss circulation materials to provide a higher success rate.

scholarly journals Laboratory Study on Core Fracturing Simulations for Wellbore Strengthening

Geofluids ◽  
2019 ◽  
Vol 2019 ◽  
pp. 1-18 ◽  
Author(s):  
Biao Ma ◽  
Xiaolin Pu ◽  
Zhengguo Zhao ◽  
Hao Wang ◽  
Wenxin Dong
Keyword(s):  
Bearing Capacity ◽  
Laboratory Study ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Lost Circulation ◽  
The Core ◽  
Fracture Pressure ◽  
Fluid Systems ◽  
Fracturing Process ◽  
Wellbore Strengthening

The lost circulation in a formation is one of the most complicated problems that have existed in drilling engineering for a long time. The key to solving the loss of drilling fluid circulation is to improve the pressure-bearing capacity of the formation. The tendency is to improve the formation pressure-bearing capacity with drilling fluid technology for strengthening the wellbore, either to the low fracture pressure of the formation or to that of the naturally fractured formation. Therefore, a laboratory study focused on core fracturing simulations for the strengthening of wellbores was conducted with self-developed fracture experiment equipment. Experiments were performed to determine the effect of the gradation of plugging materials, kinds of plugging materials, and drilling fluid systems. The results showed that fracture pressure in the presence of drilling fluid was significantly higher than that in the presence of water. The kinds and gradation of drilling fluids had obvious effects on the core fracturing process. In addition, different drilling fluid systems had different effects on the core fracture process. In the same case, the core fracture pressure in the presence of oil-based drilling fluid was less than that in the presence of water-based drilling fluid.

Nano-Enhanced Drilling Fluids: Pioneering Approach to Overcome Uncompromising Drilling Problems

2011 ◽  
Vol 134 (1) ◽  
Author(s):  
J. Abdo ◽  
M. Danish Haneef
Keyword(s):  
Rheological Properties ◽  
Size Distribution ◽  
Oil And Gas ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Lost Circulation ◽  
Drilling Operations ◽  
Cost Efficient ◽  
A Chain ◽  
Size Distribution Of Particles

The idea of pushing the limits of drilling oil and gas wells by improving drilling fluids for undemanding and cost efficient drilling operations by extracting advantage from the wonders of nanotechnology forms the basis of the work presented here. Foremost, in order to highlight the significance of reducing the size distribution of particles, new clay ATR which has a chain like structure and offers enormous surface area and increased reactivity was tested in different sizes that were chemically and mechanically milled. Bentonite which is a commonly used drilling fluid additive was also tested in different particle size distribution (PSD) and rheological properties were tested. Significant reduction in viscosity with small sized particles was recorded. The tested material called ATR throughout this paper is shown to offer better functionality than bentonite without the requirement of other expensive additives. Experiments were performed with different size distributions and compositions and drastic changes in rheological properties are observed. A detailed investigation of the shear thinning behavior was also carried out with ATR samples in order to confirm its functionality for eliminating the problem of mechanical and differential pipe sticking, while retaining suitable viscosity and density for avoidance of problems like lost circulation, poor hole cleaning and inappropriate operating hydrostatic pressures.

scholarly journals Modification of DS-01 Drilling Fluid to Reduce Formation Damage

2020 ◽  
Vol 2 (3) ◽  
Author(s):  
Winarto S. ◽  
Sugiatmo Kasmungin
Keyword(s):  
Oil And Gas ◽  
Drilling Fluid ◽  
Laboratory Research ◽  
Formation Damage ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Initial Flow ◽  
Lost Circulation ◽  
Negative Impacts ◽  
Drilling Muds

<em>In the process of drilling for oil and gas wells the use of appropriate drilling mud can reduce the negative impacts during ongoing drilling and post-drilling operations (production). In general, one of the drilling muds that are often used is conventional mud type with weighting agent barite, but the use of this type of mud often results in skin that is difficult to clean. Therefore in this laboratory research an experiment was carried out using a CaCO3 weigting agent called Mud DS-01. CaCO3 is widely used as a material for Lost Circulation Material so that it is expected that using CaCO3 mud will have little effect on formation damage or at least easily cleaned by acidizing. The aim of this research is to obtain a formula of mud with CaCO3 which at least gives formation damage. Laboratory experiments on this drilling mud using several mud samples adjusted to the property specifications of the mud program. Mud sample consists of 4, namely using super fine, fine, medium, and conventional CaCO3. First measuring mud properties in each sample then testing the filter cake breaker, testing the initial flow rate using 200 ml of distilled water and a 20 micron filter disk inserted in a 500 ml HPHT cell then assembled in a PPA jacket and injecting a pressure of 100 psi. The acidification test was then performed using 15% HCL and then pressured 100 psi for 3 hours to let the acid work to remove the cake attached to the filter disk (acidizing). Laboratory studies are expected which of these samples will minimize the formation damage caused by drilling fluids.</em>

Wood Fibre Based Lost Circulation Materials

2018 ◽  
Author(s):  
Arild Saasen ◽  
Helge Hodne ◽  
Egil Ronæs ◽  
Simen André Aarskog ◽  
Bente Hetland ◽  
...  
Keyword(s):  
Fibre Type ◽  
Drilling Fluid ◽  
Wood Fibre ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Lost Circulation ◽  
Bottom Hole Assembly ◽  
Induced Fractures ◽  
Fine Wood ◽  
Lost Circulation Materials

In this paper both a coarse and fine wood fibre type of Lost Circulation Material (LCM) is tested in the laboratory. It is shown how these fibre treatments work. The fibre type is partially oil wetting making them suitable for application in oil based drilling fluids. The fine material helps stopping small drilling induced fractures, while the coarse helps stopping lost circulation into several natural fractures or coal or conglomerate formations. In the article, the selection of wood fibres is described in more detail. Testing of the fine materials were conducted conventionally by pumping drilling fluid volumes with LCM onto slotted disks in fluid loss apparatuses. The coarse fibres are too large to be tested in these apparatuses. Therefore, gravel with grain diameter around two centimetres was filled into transparent cylinders. The pore throats created by these gravel particles were above half a centimetre. For both of these LCMs the experiments show the sensitivity of the LCM concentration in the drilling fluid to stop the lost circulation. Also, it is shown the effect of the LCM on viscous properties of the drilling fluids. Not all LCMs can be pumped through the bit. The article describes the need for circulation subs in the bottom hole assembly (BHA) to hinder the LCM blocking the entire BHA.

Dynamic and Static Sagging Characterization and Performances of Four Oil Based Muds

2016 ◽  
Author(s):  
Mesfin Belayneh ◽  
Bernt S. Aadnøy ◽  
Sharman Thomas
Keyword(s):  
Yield Stress ◽  
Storage Modulus ◽  
Viscoelastic Properties ◽  
Loss Modulus ◽  
Drilling Fluid ◽  
High Viscosity ◽  
Experimental Result ◽  
Drilling Fluids ◽  
Oil Water ◽  
Water Ratio

This paper presents the barite sagging phenomenon of four OBM systems having the same density, but different rheology properties. The investigations of barite sagging is based on dynamic sagging and viscoelasticity testing. The viscoelastic properties related to gel formation of the drilling fluids were investigated under amplitude and frequency sweeps. The study also tries to correlate the results obtained from dynamic sag with the dynamic viscoelastic properties of the drilling fluid and standard API rheology parameters. The results show that as the oil water ratio increases the drilling fluid rheology parameters such as lower shear yield stress (LSYS), yield stress (YS) and plastic viscosity (PV) parameters also increases. In addition, the viscoelastic loss and storage modulus decrease. From the viscoelasticity study, except for 90:10 OWR, it is observed that as the oil water ratio increase, the yield stress and the flow point also increases. The 90:10 OBM shows no viscoelasticity behavior. Comparing the extreme 60:40 and 90:10 OBMs (i.e. as OWR increase), the experimental result shows that the sagging index increases by 9%. The dynamic sagging factor decreases as the ratio of storage modulus to loss modulus increases (i.e. as OWR decrease). Except for high viscosity and hydraulics, the overall analysis of drilling fluids shows that the 60:40 OWR is the better in terms of sagging, filtrate loss and hole cleaning performance.

ENVIRONMENTAL DRILLING SOLUTIONS ON THE POLYMERIC BASIS

2020 ◽  
Author(s):  
E.A. Flik ◽  
◽  
Y.E. Kolodyazhnaya
Keyword(s):  
Oil And Gas ◽  
Drilling Fluid ◽  
Oil And Gas Industry ◽  
Environmental Safety ◽  
Drilling Fluids ◽  
Gas Industry ◽  
Fluid Systems ◽  
Water Based

The article assesses the environmental safety of drilling fluids that are currently widely used in the oil and gas industry. It shows active development of water-based drilling fluid systems using xanthan biopolymer.

scholarly journals Synthesis and development of smart drilling fluids using nanoparticles to tailor their transport properties for enhanced drilling operations

2018 ◽  
Author(s):  
Ζήσης Βρύζας
Keyword(s):  
Transport Properties ◽  
Yield Stress ◽  
Drilling Fluid ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Natural Fractures ◽  
Custom Made ◽  
Drilling Operations ◽  
Induced Fractures

Η γεώτρηση αποτελεί την πλέον δαπανηρή εργασία σε μια καμπάνια εξεύρεσης και παραγωγής υδρογονανθράκων. Πέραν αυτού συνιστά και την μοναδική διεργασία που δίνει τη δυνατότητα ακριβούς προσδιορισμού των αποθεμάτων στο υπέδαφος. Ο πολφός (γεωτρητικά ρευστά) είναι το ‘αίμα’ της γεώτρησης: παρέχει πίεση, μεταφορά τριμμάτων/θραυσμάτων από τον πυθμένα του φρέατος, ψύξη και λίπανση κοπτικού και στήλης, καθώς επίσης διατηρεί τα θραύσματα εν αιωρήσει όταν υπάρχει διακοπή της κυκλοφορίας. Ως ρευστό γεώτρησης (drilling fluid) χρησιμοποιείται συνήθως ένα αιώρημα πηλού και άλλων υλικών σε νερό. Τα ρευστά διάτρησης με βάση το νερό αποτελούνται από α) νερό, το οποίο αποτελεί την συνεχή φάση και παρέχει το αρχικό ιξώδες (φρέσκο ή θαλασσινό), β) ενεργά στερεά για την ενίσχυση του ιξώδους και του σημείου διαρροής (μπεντονίτης, που συνιστάται στην περίπτωση του φρέσκου νερού και ατταπουλγίτης, αμίαντος ή σιπιόλιθος, που συνιστώνται στην περίπτωση του θαλασσινού νερού), και γ) αδρανή στερεά για την επίτευξη της απαιτούμενης πυκνότητας (βαρύτης, θειούχος μόλυβδος, σιδηρομεταλλεύματα ή χαλαζιακά υλικά).Τα γεωτρητικά ρευστά αποτελούν το 10-20% του συνολικού κόστους κατά την διάρκεια μιας γεώτρησης. Ποσοστό πολύ υψηλό όταν μιλάμε για επενδύσεις εκκατομυρίων δολλαρίων. Λόγω των ολοένα πιο βαθιών αλλά και περίπλοκων γεωλογικών σχηματισμών υπάρχει τεράστια ανάγκη από την πετρελαική βιομηχανία για καινούργια και περισσότερο αποδοτικά γεωτρητικά ρευστά τα οποία θα μπορούν να ανταπεξέλθουν στα ολοένα και πιο απαιτητικά περβάλλοντα θερμοκρασίας και πίεσης. Τα σημαντικότερα ζητήματα τα οποία καλούνται να ανταποκριθούν τα ρευστά είναι οι ολοένα αυξανόμενες συνθήκες πίεσης και θερμοκρασίας στο υπέδαφος που είναι απόροια της αναζήτησης υδρογονανθράκων σε πλέον δύσβατες περιοχές με μεγαλύτερα βάθη που αυξάνουν τους κινδύνους και το κόστος για μια γεώτρηση. Η απώλεια ρευστού κυκλοφορίας (fluid loss) είναι ένα από τα σημαντικότερα και πλέον δαπανηρά προβλήματα κατά την διαδικασία μιας γεώτρησης. Ως απώλεια ρευστού κυκλοφορίας ορίζεται η συνολική ή μερική απώλεια των ρευστών της γεώτρησης σε εξαιρετικά διαπερατές ζώνες (porous sands), σε σπηλαιώδεις σχηματισμούς (cavernous zones), σε φυσικές ρηγματώσεις (natural fractures) και σε ρηγματώσεις προκαλούμενες κατά τη διάτρηση (induced fractures). Τα τελευταία χρόνια έχουν γίνει αρκετές προσπάθειες για την βελτίωση των γεωτρητικών ρευστών με την χρήση νανοσωματιδίων, τα οποία έχουν τη δυνατότητα να βελτιώσουν τις ιδιότητες των γεωτρητικών ρευστών όταν προστίθενται ακόμα και σε χαμηλές συγκεντρώσεις (<1 wt%). Οι μοναδικές τους ιδιότητες σχετίζονται με το μικρό τους μέγεθος και επομένως τον εξαιρετικά μεγάλο λόγο επιφάνειας προς όγκο.Σε αυτή την εργασία, εξετάστηκαν διάφορα εμπορικά νανοσωματίδια (Fe2O3, Fe3O4, SiO2) καθώς επίσης συντέθηκαν, με την μέθοδο της συγκαταβύθισης, νανοσωματιδία μαγνητίτη (custom-made Fe3O4), με και χωρίς επικάλυψη κιτρικού οξέος, τα οποία ερευνήθηκαν ως προς την ικανότητα τους να βελτιώσουν τις ρεολογικές ιδιότητες και την απώλεια ρευστών σε αιωρήματα μπετονίτη. Προκειμένου να χαρακτηρισθούν φυσικοχημικά τα αιωρήματα υπέστησαν ξήρανση με κοκκοποίηση σε θερμοκρασία υγρού Ν2 και κρυοξήρανση. Η μορφολογία, η κρυσταλλική δομή και οι επιφανειακές ομάδες των ξηρών κόνεων εξετάσθηκαν με ηλεκτρονική μικροσκοπία HR-TΕM, περίθλαση ακτίνων Χ (XRD), φυσική ρόφηση Ν2 και φασματοσκοπία FTIR. Οι αλληλεπιδράσεις των σωματιδίων μπετονίτη με τα νανοσωματίδια και οι διάφορες δομές που δημιουργούνται και πως τελικά αυτές επηρεάζουν τις ρεολογικές ιδιότητες των αιωρημάτων εξετάστηκαν με το HR-TEM στους 25°C και 60°C. Με βάση τις εικόνες από το HR-TEM, ένα μοντέλο αλληλεπιδράσεων μεταξύ των διαφορετικών τύπων νανοσωματιδίων και σωματιδίων μπετονίτη δημιουργήθηκε για πρώτη φορά για τέτοια αιωρήματα. Οι ρεολογικές ιδιότητες των παραγόμενων δειγμάτων εξετάστηκαν και σε συνθήκες ατμοσφαιρικής πίεσης (μέχρι 70°C) με την χρήση περιστροφικού ιξωδόμετρου (Grace M3600-Couette type geometry) αλλά και σε συνθήκες υψηλής πίεσης και θερμοκρασίας (69 bar-121°C) (Chandler 7600 HPHT viscometer). Το μοντέλο Herschel-Bulkley χρησιμοποιήθηκε για να περιγράψει τη μεταβολή του ιξώδους με τη μεταβολή των ρεολογικών παραμέτρων δείχνοντας εξαιρετική εφαρμογή για τις διαφορετικές πειραματικές μετρήσεις με συντελεστές συσχέτισης (R2) >0.99 σε όλες τις περιπτώσεις. Οι ρεολογικές μετρήσεις έδειξαν ότι η προσθήκη των νανοσωματιδίων βελτιώνει σημαντικά τις ρεολογικές ιδιότητες των αιωρημάτων μπετονίτη στις διάφορες συνθήκες πίεσης και θερμοκρασίας. Οι απώλειες ρευστών (fluid loss) εξετάστηκαν με φιλτροπρέσες υψηλής πίεσης και θερμοκρασίας (20.7 bar και 121°C) οι οποίες υπολογίζουν τον ρυθμό διήθησης του πολφού μέσω του χρησιμοποιούμενου φίλτρου (κεραμικός δίσκος). Η μεγαλύτερη μείωση στην απώλεια ρευστών επιτεύχθηκε για το δείγμα που περιείχε 0.5 wt% custom-made Fe3O4 με μείωση -40% σε σχέση με το αρχικό δείγμα μπετονίτη που δείχνει την τεράστια ικανότητα των νανοσωματιδίων να βελτιώσουν σημαντικά τις απώλειες ρευστών ακόμα και σε τόσο μικρές συγκεντρώσεις. Τέλος, εξετάστηκε η ικανότητα των παραγόμενων ρευστών να αλλάζουν τις ρεολογικές τους ιδιότητες υπό την επίδραση διάφορων μαγνητικών πεδίων (μέχρι 0.7 Tesla). Τα αποτελέσματα έδειξαν ότι τα καινούργια γεωτρητικά ρευστά έχουν την ικανότητα να αυξάνουν την τάση διολίσθησης (yield stress) έως και 300% σε σχέση με αυτή που μετρήθηκε χωρίς την εφαρμογή μαγνητικού πεδίου. Αυτό είναι κάτι πολύ σημαντικό που επιτρέπει την χρήση έξυπνων ρευστών (smart drilling fluids) τα οποία μπορούν να εξοικονομήσουν και χρόνο αλλά και κόστη κατά την διάρκεια μιας γεώτρησης.Τα νανοσωματίδια δείχνουν πολλές ελπιδοφόρες δυνατότητες σε εφαρμογές γεωτρήσεων αφού έχουν τη δυνατότητα να βελτιώσουν ή και να λύσουν το πρόβλημα της απώλειας ρευστών, όταν προστίθενται ακόμα και σε χαμηλές συγκεντρώσεις (>0.5 wt%), ενώ ταυτόχρονα βελτιστοποιούν τις ρεολογικές ιδιότητες των γεωτρητικών ρευστών. Η χρήση τους για την ανάπτυξη βελτιωμένων γεωτρητικών ρευστών υπόσχεται να αλλάξει την βιομηχανία των γεωτρήσεων και να την βοηθήσει να εξορυχθούν πολύπλοκοι γεωλογικοί σχηματισμοί πιο αποδοτικά αλλά και οικονομικά.

scholarly journals Numerical Modeling of Foam Drilling Hydraulics

2007 ◽  
Vol 4 (1) ◽  
pp. 103 ◽  
Author(s):  
Ozcan Baris ◽  
Luis Ayala ◽  
W. Watson Robert
Keyword(s):  
Drilling Fluid ◽  
Operating Conditions ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Lost Circulation ◽  
Pressure Profiles ◽  
Drilling Operations ◽  
Parametric Studies ◽  
Bit Life ◽  
Foam Drilling

The use of foam as a drilling fluid was developed to meet a special set of conditions under which other common drilling fluids had failed. Foam drilling is defined as the process of making boreholes by utilizing foam as the circulating fluid. When compared with conventional drilling, underbalanced or foam drilling has several advantages. These advantages include: avoidance of lost circulation problems, minimizing damage to pay zones, higher penetration rates and bit life. Foams are usually characterized by the quality, the ratio of the volume of gas, and the total foam volume. Obtaining dependable pressure profiles for aerated (gasified) fluids and foam is more difficult than for single phase fluids, since in the former ones the drilling mud contains a gas phase that is entrained within the fluid system. The primary goal of this study is to expand the knowledge-base of the hydrodynamic phenomena that occur in a foam drilling operation. In order to gain a better understanding of foam drilling operations, a hydrodynamic model is developed and run at different operating conditions. For this purpose, the flow of foam through the drilling system is modeled by invoking the basic principles of continuum mechanics and thermodynamics. The model was designed to allow gas and liquid flow at desired volumetric flow rates through the drillstring and annulus. Parametric studies are conducted in order to identify the most influential variables in the hydrodynamic modeling of foam flow. 

Heat Moisture Modified Rice Flours as Additive in Drilling Fluids

2021 ◽  
Vol 80 (1) ◽  
pp. 62-72
Author(s):  
Bunyami Shafie ◽  
Lee Huei Hong ◽  
Phene Neoh Pei Nee ◽  
Fatin Hana Naning ◽  
Tze Jin Wong ◽  
...  
Keyword(s):  
Oil And Gas ◽  
Drilling Fluid ◽  
Low Cost ◽  
Health Concern ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Fluid Mixture ◽  
Gas Drilling ◽  
Water Based ◽  
Rice Flours

Drilling mud is a dense, viscous fluid mixture used in oil and gas drilling operations to bring rock cuttings to the earth's surface from the boreholes as well as to lubricate and cool the drill bit. Water-based mud is commonly used due to its relatively inexpensive and easy to dispose of. However, several components and additives in the muds become increasingly cautious and restricted. Starch was introduced as a safe and biodegradable additive into the water-based drilling fluid, in line with an environmental health concern. In this study, the suitability of four local rice flours and their heat moistures derivatives to be incorporated in the formulation of water-based drilling fluid was investigated. They were selected due to their natural amylose contents (waxy, low, intermediate, and high). They were also heat moisture treated to increase their amylose contents. Results showed that the addition of the rice flours into water-based mud significantly reduced the density, viscosity, and filtrate volume. However, the gel strength of the mud was increased. The rice flours, either native or heat moisture treated, could serve as additives to provide a variety of low cost and environmentally friendly drilling fluids to be incorporated and fitted into different drilling activity.

Risk Planning and Mitigation in Oil Well Fields

2015 ◽  
Vol 4 (4) ◽  
pp. 27-48
Author(s):  
Nediljka Gaurina-Međimurec ◽  
Borivoje Pašić ◽  
Petar Mijić
Keyword(s):  
Preventive Measures ◽  
Drilling Fluid ◽  
Oil Well ◽  
Remedial Measures ◽  
Successful Management ◽  
Lost Circulation ◽  
Wellbore Strengthening ◽  
Lost Circulation Materials ◽  
Industry Experience ◽  
Tools And Methods

Lost circulation presents one of the major risks associated with drilling. The complete prevention of lost circulation is impossible but limiting circulation loss is possible if certain precautions are taken. Industry experience has proved that is often easier and more effective to prevent the occurrence of loss than to attempt to stop or reduce them once they have started. The problem of lost circulation was magnified considerably when operators began drilling deeper and/or depleted formations. A strategy for successful management of lost circulation should include preventative (best drilling practices, drilling fluid selection, and wellbore strengthening materials) and remedial measures when lost circulation occurs through the use of lost circulation materials. In this paper the authors present lost circulation zones and causes, potential zones of lost circulation, excessive downhole pressures causes, preventive measures, tools and methods for locating loss zones and determining the severity of loss, lost circulation materials, and recommended treatments.

Sign in / Sign up

Export Citation Format

Share Document