Photocatalytic removal of nitrate using TiO2/polyacrylonitrile nanofiber membrane synthesized by co-electrospinning process

2014 ◽  
Vol 14 (4) ◽  
pp. 554-560 ◽  
Author(s):  
S. P. Suriyaraj ◽  
M. Benasir Begam ◽  
S. G. Deepika ◽  
P. Biji ◽  
R. Selvakumar
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Tio2 Nanoparticles ◽  
Nitrate Removal ◽  
Electrospinning Process ◽  
Order Kinetic ◽  
Nanofiber Membrane ◽  
Electrospinning Technique ◽  
X Ray ◽  
Pan Nanofiber

The present study investigates the development of titanium dioxide (TiO2)/polyacrylonitrile (PAN) nanofiber membrane for the removal of nitrate from aqueous solution by photocatalysis. The TiO2 nanoparticles were synthesized by conventional sol–gel method followed by blending them into PAN polymer. The blended solution was electrospun into nanofiber using the co-electrospinning technique. The nanoparticle, PAN nanofibers and the TiO2 impregnated nanofibers were characterized using suitable techniques like X-ray diffraction, high-resolution transmission electron microscopy and scanning electron microscopy attached with energy dispersive X-ray spectroscopy. The average size and the diameter of the TiO2 nanoparticles and TiO2/PAN nanofibers were found to be 22 ± 0.32 nm and 90 ± 15 nm respectively. TiO2 nanoparticles and TiO2/PAN nanofibers showed maximum nitrate removal of 74.67 and 39% respectively at 10 mg/L nitrate concentration at pH 4. However at higher concentration (50 mg/L), the nitrate removal was found to be only 16.87%. The experimental data were fitted onto pseudo second-order kinetic model. The impregnation of TiO2 nanoparticles into the PAN nanofibers by co-electrospinning techniques lead to higher removal of nitrate in aqueous solution at lower concentration (10 mg/L and below). However at higher concentration, the TiO2/PAN nanofiber membrane was inefficient to remove nitrate.

Synthesis of TiO2 nanoparticles in the PAMAM hydrogen network template

e-Polymers ◽  
2016 ◽  
Vol 16 (3) ◽  
pp. 177-180 ◽  
Author(s):  
Zheng Peng ◽  
Hong Li ◽  
Xinwu Ba ◽  
Junchai Zhao ◽  
Xiuguo Sun ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Transmission Electron Microscopy ◽  
Tio2 Nanoparticles ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Good Template ◽  
Ammonia Aqueous Solution ◽  
Hydrogen Network

AbstractIntramolecular nanocavities in polyamidoamine (PAMAM) are usually used as a good template to synthesize nanoparticles. In this paper, TiO2 nanoparticles were prepared successfully by the interspaces of the hydrogen network between PAMAM. The possible mechanism was that PAMAM could form the steady microspheres with many interspaces in ammonia aqueous solution at pH=10. The interspaces of the hydrogen network could act as the template for preparing TiO2 nanoparticles. The results were proved by transmission electron microscopy (TEM) and X-ray diffraction (XRD).

scholarly journals Removal of methylene blue from aqueous solution by mesoporous silicalite-1 synthetized using carboxymethyl cellulose as template

2021 ◽  
Author(s):  
Sabarish Radoor ◽  
Jasila Karayil ◽  
Aswathy Jayakumar ◽  
Jyothi Mannekote Shivanna ◽  
Jyotishkumar Parameswaranpillai ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Contact Time ◽  
Dye Removal ◽  
Batch Adsorption ◽  
Aqueous Environment ◽  
Order Kinetic ◽  
Adsorption Method ◽  
X Ray ◽  
Adsorption Desorption

Abstract In the present work, we have developed a mesoporous silicalite-1 using CMC as a template for the removal of MB from aqueous solution. The synthesized silicalite-1 were characterised using scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), Energy-dispersive X-ray spectroscopy (EDX) and N2 adsorption-desorption isotherm (BET). XRD and FTIR analysis confirmed the formation of crystallinity and development of MFI structure in the mesoporous silicalite-1. The adsorption of MB dye on mesoporous silicalite-1 was conducted by batch adsorption method. The effect of various parameters such as adsorbent dosage, initial dye concentration, contact time and temperature on the dye uptake ability of silicalite-1 was investigated. The operating parameters for the maximum adsorption are silicalite-1 dosage (0.1 wt%), contact time (240 min), initial dye concentration (10 ppm) and temperature (30℃). The MB dye removal onto mesoporous silicalite-1 followed pseudo-second-order kinetic and Freundlich isotherm. The silicalite-1 exhibits 86% removal efficiency even after six adsorption-desorption cycle. Therefore, the developed mesoporous silicalite-1 is an effective eco-friendly adsorbent for MB dye removal from aqueous environment.

scholarly journals Removal of methylene blue from aqueous solution by mesoporous silicalite-1 synthetized using carboxymethyl cellulose as template

2021 ◽  
Author(s):  
Sabarish Radoor ◽  
Jasila Karayil ◽  
Aswathy Jayakumar ◽  
Jyothi Mannekote Shivanna ◽  
Jyotishkumar Parameswaranpillai ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Contact Time ◽  
Dye Removal ◽  
Batch Adsorption ◽  
Aqueous Environment ◽  
Order Kinetic ◽  
Adsorption Method ◽  
X Ray ◽  
Adsorption Desorption

Abstract In the present work, we have developed a mesoporous silicalite-1 using CMC as a template for the removal of MB from aqueous solution. The synthesized silicalite-1 were characterised using scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), Energy-dispersive X-ray spectroscopy (EDX) and N2 adsorption-desorption isotherm (BET). XRD and FTIR analysis confirmed the formation of crystallinity and development of MFI structure in the mesoporous silicalite-1. The adsorption of MB dye on mesoporous silicalite-1 was conducted by batch adsorption method. The effect of various parameters such as adsorbent dosage, initial dye concentration, contact time and temperature on the dye uptake ability of silicalite-1 was investigated. The operating parameters for the maximum adsorption are silicalite-1 dosage (0.1 wt%), contact time (240 min), initial dye concentration (10 ppm) and temperature (30°C). The MB dye removal onto mesoporous silicalite-1 followed pseudo-second-order kinetic and Freundlich isotherm. The silicalite-1 exhibits 86% removal efficiency even after six adsorption-desorption cycle. Therefore, the developed mesoporous silicalite-1 is an effective eco-friendly adsorbent for MB dye removal from aqueous environment.

scholarly journals Magnetic/Polyetherimide-Acrylonitrile Composite Nanofibers for Nickel Ion Removal from Aqueous Solution

Membranes ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 50
Author(s):  
Muhammad Omer Aijaz ◽  
Mohammad Rezaul Karim ◽  
Hamad F. Alharbi ◽  
Nabeel H. Alharthi ◽  
Fahad S. Al-Mubaddel ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Nanofiber Membrane ◽  
Nickel Ion ◽  
Nickel Ions ◽  
X Ray ◽  
Ion Removal ◽  
Composite Nanofiber ◽  
Pseudo Second Order

In this study, a magnetic/polyetherimide-acrylonitrile composite nanofiber membrane with effective adsorption of nickel ions in an aqueous solution was created using a simple electrospinning method. Iron oxide nanoparticles (NPs) were stirred and ultrasonically dispersed into a polyetherimide-acrylonitrile solution to create a homogenous NPs suspension, which was placed in an electrospinning machine to produce a uniform and smooth nanofiber composite membrane. Nanoparticle incorporation into this membrane was confirmed using scanning electron microscope, energy dispersive X-ray spectroscopy (EDX), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and NPs aqueous stability from a leaching test. The high adsorption capability of the membrane on nickel ions was attributed to the combination of magnetic NPs, polyetherimide-acrylonitrile matrix, and the nanostructure of the membrane. A membrane containing magnetic NPs demonstrated the maximum adsorption capabilities (102 mg/g) of nickel ions in an aqueous solution. Various kinetic and isotherm models were applied to understand the adsorption behavior, such as pseudo-second-order kinetic and Langmuir isotherm models. A polyetherimide-acrylonitrile composite nanofiber membrane containing magnetic NPs could be used as an environmentally friendly and nontoxic adsorbent for the removal of nickel ions in an aqueous medium due to its ease of preparation and use and stability in aqueous mediums.

scholarly journals Enhanced Photocatalytic Activity of Hybrid rGO@TiO2/CN Nanocomposite for Organic Pollutant Degradation under Solar Light Irradiation

Catalysts ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1023
Author(s):  
Martina Kocijan ◽  
Lidija Ćurković ◽  
Tina Radošević ◽  
Matejka Podlogar
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Photocatalytic Activity ◽  
Tio2 Nanoparticles ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Ph Value ◽  
Organic Pollutant ◽  
Anatase Tio2 ◽  
X Ray

The three-component hybrid (rGO/TiO2/CN) nanocomposite was prepared in order to enhance the photocatalytic properties of anatase TiO2 nanoparticles (NPs) under solar-like irradiation. The rGO/TiO2/CN was prepared in a mixture of the reduced graphene oxide (rGO, 8 wt%), anatase TiO2 nanoparticles (NPs), and graphitic carbon nitride (g-C3N4, 16 wt%). It was self-assembled through the one-step hydrothermal method, followed by an annealing process. The photocatalyst was thoroughly characterized by means of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), the Brunauer-Emmett-Teller (BET) nitrogen adsorption/desorption technique and UV-Vis diffuse reflectance spectroscopy (DRS). The photocatalytic activity of the TiO2, TiO2/rGO, TiO2/CN and hybrid rGO/TiO2/CN nanocomposite was studied through the degradation of a rhodamine B (RhB) aqueous solution under solar-like irradiation. The results showed that the highest photocatalytic activity was achieved by the rGO/TiO2/CN mixture, which can be attributed to the synergistic effect of the incorporation of both rGO and g-C3N4 with TiO2. Further, the influence of the pH value of the RhB dye aqueous solution and different water matrix (Milli-Q, tap, and alkaline water) on the photocatalytic efficiency of the rGO/TiO2/CN nanocomposite was examined. In addition, a recycle test was performed for hybrid rGO@TiO2/CN to investigate the effectiveness of the photodegradation of RhB dye in three successive cycles. The conducted results indicate that the pH value of RhB dye aqueous solution and water matrices play an important role in the photocatalytic degradation rate.

scholarly journals Release of toxic methylene blue from water by mesoporous silicalite-1: characterization, kinetics and isotherm studies

2021 ◽  
Vol 11 (7) ◽  
Author(s):  
Sabarish Radoor ◽  
Jasila Karayil ◽  
Aswathy Jayakumar ◽  
Jyotishkumar Parameswaranpillai ◽  
Suchart Siengchin
Keyword(s):  
Electron Microscopy ◽  
Contact Time ◽  
Dye Removal ◽  
Batch Adsorption ◽  
Aqueous Environment ◽  
Order Kinetic ◽  
Adsorption Method ◽  
X Ray ◽  
Ft Ir ◽  
Adsorption Desorption

AbstractIn the present work, we have developed a mesoporous silicalite-1 using CMC as a template for the removal of MB from aqueous solution. The synthesized silicalite-1 were characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), Energy-dispersive X-ray spectroscopy (EDAX) and N2 adsorption–desorption isotherm (BET). XRD and FT-IR analysis confirmed the formation of crystallinity and development of MFI structure in the mesoporous silicalite-1. The adsorption of MB dye on mesoporous silicalite-1 was conducted by batch adsorption method. The effect of various parameters such as adsorbent dosage, initial dye concentration, contact time and temperature on the dye uptake ability of silicalite-1 was investigated. The operating parameters for the maximum adsorption are silicalite-1 dosage (0.1 wt%), contact time (240 min), initial dye concentration (10 ppm) and temperature (30 ℃). The MB dye removal onto mesoporous silicalite-1 followed pseudo-second-order kinetic and Freundlich isotherm. The silicalite-1 exhibits 86% removal efficiency even after six adsorption–desorption cycle. Therefore, the developed mesoporous silicalite-1 is an effective eco-friendly adsorbent for MB dye removal from aqueous environment.

Dissolution Characteristics and Morphology of Large-sized Scorodite Particles Synthesized from Fe(II) and As(V) in Aqueous Solution

2012 ◽  
Vol 31 (4-5) ◽  
pp. 451-458 ◽  
Author(s):  
S. Fujieda ◽  
K. Shinoda ◽  
T. Inanaga ◽  
M. Abumiya ◽  
S. Suzuki
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Surface Defects ◽  
Atmospheric Temperature ◽  
Orthorhombic Structure ◽  
X Ray ◽  
Long Term Storage ◽  
Transmission Electron ◽  
Term Storage

AbstractA novel process for preparing scorodite particles with a diameter of approximately 20 µm from Fe(II) and As(V) in aqueous solution has been developed by DOWA Metals and Mining. In the present study, the dissolution characteristics of iron and arsenic from the scorodite particles synthesized by this process have been investigated under different conditions. The results show that the concentration of arsenic dissolved from the particles in aqueous solution is very low, but it has a complicated dependence on the temperature and pH of the solution. Transmission electron microscopy (TEM) with an energy dispersive X-ray spectrometer (EDS) was used to analyze the morphology, structure, and composition of the scorodite particles. The results indicate that the scorodite particles exhibit a nearly octahedral shape with planes composed of almost (111) planes in the orthorhombic structure. The concentration of iron at the surface of the particles is higher than that of iron inside of the particles. This characteristic morphology, along with the minimal surface defects of the scorodite particles, is considered to be responsible for the low dissolution of arsenic from the particles in aqueous solution. Atmospheric temperature and solution conditions were also found to be important for the safe, long-term storage of arsenic using scorodite particles.

scholarly journals Photocatalytic Degradation of Tetracycline in Aqueous Solution Using Copper Sulfide Nanoparticles

Catalysts ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1238
Author(s):  
Murendeni P. Ravele ◽  
Opeyemi A. Oyewo ◽  
Sam Ramaila ◽  
Lydia Mavuru ◽  
Damian C. Onwudiwe
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Copper Sulfide ◽  
Degradation Rate ◽  
Light Exposure ◽  
Reaction System ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Pure Phase

In this paper, spherical-shaped pure phase djurleite (Cu31S16) and roxbyite (Cu7S4) nanoparticles were prepared by a solvothermal decomposition of copper(II) dithiocarbamate complex in dodecanthiol (DDT). The reaction temperature was used to control the phases of the samples, which were represented as Cu31S16 (120 °C), Cu31S16 (150 °C), Cu7S4 (220 °C), and Cu7S4 (250 °C) and were characterized by using X-ray diffraction (XRD), scanning and transmission electron microscopy (SEM and TEM), and absorption spectroscopy. The samples were used as photocatalysts for the degradation of tetracycline (TC) under visible light irradiation. The results of the study showed that Cu7S4 (250 °C) exhibited the best activity in the reaction system with the TC degradation rate of up to 99% within 120 min of light exposure, while the Cu31S16 (120 °C) system was only 46.5% at the same reaction condition. In general, roxbyite Cu7S4 (250 °C) could be considered as a potential catalyst for the degradation of TC in solution.

scholarly journals Preparation of pod-shaped TiO 2 and Ag@TiO 2 nano burst tubes and their photocatalytic activity

2019 ◽  
Vol 6 (9) ◽  
pp. 191019 ◽  
Author(s):  
Shang Wang ◽  
Zhaolian Han ◽  
Tingting Di ◽  
Rui Li ◽  
Siyuan Liu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Oxalic Acid ◽  
Ultraviolet Light ◽  
Photoelectron Spectroscopy ◽  
Degradation Process ◽  
Catalytic Performance ◽  
Tetrabutyl Titanate ◽  
Order Kinetic ◽  
X Ray

The pod-shaped TiO 2 nano burst tubes (TiO 2 NBTs) were prepared by the combination of electrospinning and impregnation calcination with oxalic acid (H 2 C 2 O 4 ), polystyrene (PS) and tetrabutyl titanate. The silver nanoparticles (AgNPs) were loaded onto the surface of TiO 2 NBTs by ultraviolet light reduction method to prepare pod-shaped Ag@TiO 2 NBTs. In this work, we analysed the effect of the amount of oxalic acid on the cracking degree of TiO 2 NBTs; the effect of the concentration of AgNO 3 solution on the particle size and loading of AgNPs on the surface of TiO 2 NBTs. Scanning electron microscopy and transmission electron microscopy investigated the surface morphology of samples. X-ray diffraction and X-ray photoelectron spectroscopy characterized the structure and composition of samples. Rhodamine B (RhB) solution was used to evaluate the photocatalytic activity of pod-shaped TiO 2 NBTs and Ag@TiO 2 NBTs. The results showed that TiO 2 NBTs degraded 91.0% of RhB under ultraviolet light, Ag@TiO 2 NBTs degraded 95.5% under visible light for 75 and 60 min, respectively. The degradation process of both samples was consistent with the Langmuir–Hinshelwood first-order kinetic equation. Therefore, the catalytic performance of the sample is: Ag@TiO 2 NBTs > TiO 2 NBTs > TiO 2 nanotubes.

scholarly journals Preparation, Characterization, and Photocatalytic Properties of Modified Red Mud

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Mingjie Ma ◽  
Guanyu Wang ◽  
Zhengpeng Yang ◽  
Shanxiu Huang ◽  
Weijie Guo ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Scanning Electron Microscopy ◽  
Uv Irradiation ◽  
Red Mud ◽  
Structure Property ◽  
X Ray Diffraction ◽  
X Ray ◽  
Xrf Scanning ◽  
Scanning Electron

Solid waste red mud was modified by HCl leaching. The structure property and composition of modified red mud were investigated by X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF), scanning electron microscopy (SEM), and Brunauer-Emmett-Teller (BET). Under UV irradiation, methyl orange (MO) aqueous solution was photodegraded by modified red mud. The obtained results showed that the specific surface area of modified red mud was 317.14 m2/g, which was about 40 times higher than that of the normal red mud. After UV irradiation for 50 min, the removal percentage of MO reached 94.2%. The study provided a novel way for the application of red mud to the photocatalytic degradation of organic wastes.

Sign in / Sign up

Export Citation Format

Share Document