scholarly journals Membrane distillation crystallization using PVDF membrane incorporated with TiO2 nanoparticles and nanocellulose

2020 ◽  
Vol 20 (5) ◽  
pp. 1629-1642 ◽  
Author(s):  
Hoi-Fang Tan ◽  
Why-Ling Tan ◽  
N. Hamzah ◽  
M. H. K. Ng ◽  
B. S. Ooi ◽  
...  
Keyword(s):  
Pore Size ◽  
Tio2 Nanoparticles ◽  
Polyvinylidene Fluoride ◽  
Phase Inversion ◽  
Membrane Distillation ◽  
Coagulation Bath ◽  
Membrane Thickness ◽  
Permeate Flux ◽  
Sem Images ◽  
Pvdf Membrane

Abstract Polyvinylidene fluoride (PVDF) membrane was improved using TiO2 nanoparticles and nanocellulose for membrane distillation crystallization in this work. Besides the addition of TiO2 nanoparticles and nanocellulose, PVDF membrane was post-modified with octadecyltrichlorosilane after phase inversion using a dual coagulation bath. The addition of hydrophilic TiO2 nanoparticles and nanocellulose reduced membrane hydrophobicity, but the dispersed TiO2 nanoparticles assisted silane modification to improve surface hydrophobicity. Besides reducing the agglomeration of TiO2 nanoparticles, nanocellulose induced the formation of larger pore size and higher porosity as proven in SEM images and gravimetric measurement, respectively. The abundant moieties of nanocellulose accelerated the exchange between solvent and non-solvent during phase inversion for the formation of large pore size and porosity, but membrane thickness increased due to the thickening effects. The modified membrane showed higher water permeate flux in membrane distillation with salt rejection greater than 97%. Severe fouling in membrane distillation crystallization was not observed.

scholarly journals Membrane distillation of saline and oily water using nearly superhydrophobic PVDF membrane incorporated with SiO2 nanoparticles

2018 ◽  
Vol 78 (12) ◽  
pp. 2532-2541 ◽  
Author(s):  
N. Hamzah ◽  
M. Nagarajah ◽  
C. P. Leo
Keyword(s):  
Polyvinylidene Fluoride ◽  
Volume Ratio ◽  
Sio2 Nanoparticles ◽  
Membrane Distillation ◽  
Permeate Flux ◽  
Oil And Grease ◽  
Sem Images ◽  
Water Contact ◽  
Pvdf Membrane ◽  
Oily Water

Abstract Fat, oil and grease in wastewater generated from household kitchens, restaurants and food processing plants affect sewer systems, water resources and environment adversely. Hence, membrane distillation of saline and oily water was studied using a nearly superhydrophobic membrane developed in this work. Polyvinylidene fluoride (PVDF) membrane incorporated SiO2 nanoparticles was synthesized via phase inversion with dual baths and modified using hexadecyltrimethoxy silane. The volume ratio of silane to ethanol was varied between 1:200 to 1:25. The membrane characteristics were examined using a goniometer, a porometer, scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The PVDF-SiO2 membrane modified using the volume ratio of 1:50 achieved the highest water contact angle of 141.6° and LEP of 2.642 bar. This membrane was further tested in membrane distillation to observe the permeate flux of distilled water, saline solution (1 M NaCl) as well as saline and oily solution (1 M NaCl; 1,000 ppm of palm oil). The modified PVDF/SiO2 showed high permeate flux which is nearly four times of the permeate flux of neat PVDF membrane, but still susceptible of salt and oil fouling as shown in SEM images.

scholarly journals Theoretical and Experimental Desalination Using Ultrasound Assisted PVDF Membrane in Direct Contact Membrane Distillation

2019 ◽  
Vol 8 (6) ◽  
pp. 1229-1234
Keyword(s):  
Contact Angle ◽  
Pore Size ◽  
Transition Region ◽  
Direct Contact ◽  
Membrane Distillation ◽  
Membrane Properties ◽  
Permeate Flux ◽  
Pvdf Membrane ◽  
Direct Contact Membrane Distillation ◽  
Ultrasound Assisted

Desalination by the direct contact membrane distillation (DCMD) for prepared saline water and Ambazari lake water sample was investigated. The self-prepared ultrasound assisted polyvinylidene fluoride (PVDF) membrane by wet phase inversion method exhibited effects on membrane contact angle, pore size, and porosity and investigated performance of DCMD. Membrane properties are characterized and employed in theoretical model with assumptions for water vapor transport in the transition region. It is observed that similar pattern obtained for permeate flux from experimental results and simulated results for transition region. Effects of operating parameter on permeate flux also simulated and compared with experimental data. For this work mathematical models developed and simulated in Polymath. PVDF membrane exhibited its characteristics like contact angle, pore size and flux enhancement may be due to ultrasound assisted polymer solution preparation for membrane casting.

Performance of Surface Modification of Polyvinylidene Fluoride Hollow Fiber Membrane in Membrane Distillation

2013 ◽  
Vol 795 ◽  
pp. 137-140 ◽  
Author(s):  
Kok Chung Chong ◽  
Soon Onn Lai ◽  
K.M. Lee ◽  
Woei Jye Lau ◽  
B.S. Ooi
Keyword(s):  
Hollow Fiber ◽  
Polyvinylidene Fluoride ◽  
Hollow Fiber Membrane ◽  
Skin Layer ◽  
Membrane Distillation ◽  
Permeate Flux ◽  
Fiber Membrane ◽  
Water And Wastewater Treatment ◽  
Pvdf Membrane ◽  
Different Temperatures

Membrane distillation (MD) is one of the novel separation methods used in water and wastewater treatment processes. MD is a thermal driven process which has the potential to be integrated with renewable energy source and can be operated at very low pressure. Polyvinylidene fluoride (PVDF) is a hydrophobic polymeric material which is commonly used to prepare MD membrane. In this study, surface modifying macromolecule (SMM) was added as additive into PVDF dope solution and then the hollow fiber membrane was prepared using phase inversion process. The membrane was characterized with respect to morphology and permeates flux at different temperatures. The results revealed that the PVDF membrane blended with SMM exhibited higher permeate flux than PVDF neat membrane did, mainly due to the better pore size distribution and thinner skin layer. This finding indicated the role of SMM in modifying the properties of PVDF membrane for MD process.

scholarly journals Improvement of Membrane Distillation Using PVDF Membrane Incorporated with TiO2 Modified by Silane and Optimization of Fabricating Conditions

Membranes ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 95
Author(s):  
Fida Tibi ◽  
Seong-Jik Park ◽  
Jeonghwan Kim
Keyword(s):  
Direct Contact ◽  
Phase Inversion ◽  
Membrane Distillation ◽  
Inversion Method ◽  
Permeate Flux ◽  
Pvdf Membrane ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Phase Inversion Method ◽  
Silane Concentration

The objectives in this study are to improve the performance of PVDF membrane by incorporating TiO2 and silane at various dosages and optimize fabricating conditions by using response surface methodology (RSM) for membrane distillation (MD) application. The PVDF membrane was synthesized by phase inversion method using various TiO2, silane and polymer concentrations. Membranes were characterized by performing contact angle measurements, SEM and FTIR observations. Ammonia rejection and permeate flux were measured by operating a direct contact distillation module treating ammonium chloride solution. A PVDF membrane created by adding TiO2 modified by silane improved membrane hydrophobicity. However, the effect of silane on membrane hydrophobicity was less pronounced at higher TiO2 concentrations. Highest ammonium rejection was associated with the highest membrane hydrophobicity. RSM analysis showed that fabricating conditions to achieve highest flux (10.10 L/m2·h) and ammonium rejection (100.0%) could be obtained at 31.3% silane, 2.50% TiO2, and 15.48% polymer concentrations. With a PVDF-TiO2 composite membrane for MD application, the effect of TiO2 was dependent upon silane concentration. Increasing silane concentration improved membrane hydrophobicity and ammonium rejection. RSM analysis was found to bea useful way to explore optimum fabricating conditions of membranes for the permeate flux and ammonium rejection in MD.

scholarly journals Electrospun Nanostructured Membrane Engineering Using Reverse Osmosis Recycled Modules: Membrane Distillation Application

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1601
Author(s):  
Jorge Contreras-Martínez ◽  
Carmen García-Payo ◽  
Mohamed Khayet
Keyword(s):  
Reverse Osmosis ◽  
Polyvinylidene Fluoride ◽  
Membrane Distillation ◽  
Permeate Flux ◽  
Electrospinning Technique ◽  
Salt Rejection ◽  
Rejection Factor ◽  
Nanofibrous Membranes ◽  
Membrane Engineering ◽  
Desalination Plants

As a consequence of the increase in reverse osmosis (RO) desalination plants, the number of discarded RO modules for 2020 was estimated to be 14.8 million annually. Currently, these discarded modules are disposed of in nearby landfills generating high volumes of waste. In order to extend their useful life, in this research study, we propose recycling and reusing the internal components of the discarded RO modules, membranes and spacers, in membrane engineering for membrane distillation (MD) technology. After passive cleaning with a sodium hypochlorite aqueous solution, these recycled components were reused as support for polyvinylidene fluoride nanofibrous membranes prepared by electrospinning technique. The prepared membranes were characterized by different techniques and, finally, tested in desalination of high saline solutions (brines) by direct contact membrane distillation (DCMD). The effect of the electrospinning time, which is the same as the thickness of the nanofibrous layer, was studied in order to optimize the permeate flux together with the salt rejection factor and to obtain robust membranes with stable DCMD desalination performance. When the recycled RO membrane or the permeate spacer were used as supports with 60 min electrospinning time, good permeate fluxes were achieved, 43.2 and 18.1 kg m−2 h−1, respectively; with very high salt rejection factors, greater than 99.99%. These results are reasonably competitive compared to other supported and unsupported MD nanofibrous membranes. In contrast, when using the feed spacer as support, inhomogeneous structures were observed on the electrospun nanofibrous layer due to the special characteristics of this spacer resulting in low salt rejection factors and mechanical properties of the electrospun nanofibrous membrane.

scholarly journals Exploiting the Interplay between Liquid-Liquid Demixing and Crystallization of the PVDF Membrane for Membrane Distillation

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
N. I. M. Nawi ◽  
M. R. Bilad ◽  
N. A. H. M. Nordin ◽  
M. O. Mavukkandy ◽  
Z. A. Putra ◽  
...  
Keyword(s):  
Polyvinylidene Fluoride ◽  
Water Flux ◽  
High Water ◽  
Membrane Distillation ◽  
Degree Of Crystallinity ◽  
Solution Temperature ◽  
Hydrophobic Membrane ◽  
Sem Images ◽  
Cold Temperatures ◽  
Dope Solution

Membrane distillation (MD) purifies water by transporting its vapor through a hydrophobic membrane. An ideal MD membrane poses high water flux and high fouling, scaling, and wetting resistances. In this study, we develop polyvinylidene fluoride (PVDF) membranes for MD by focusing on reduction of PVDF degree of crystallinity. We explore the roles of dope solution temperature in dictating the phase separation mechanisms as well as the structure and the performance of semicrystalline PVDF membranes. DSC spectra show that higher dope solution temperature depresses crystallinity via formation of imperfect crystal. Such findings were also supported by FTIR and XRD results. The SEM images reveal formation of spherulite-like morphology in the membrane matrices for membranes prepared from high temperature dope solutions. A good balance between solid-liquid and liquid-liquid phase separations that offers low degree of crystallinity was found at a dope solution temperature of 60°C (PVDF-60), which showed the MD flux of 18 l/m2 h (vs. 6 l/m2 h for temperature of 25°C, as a benchmark) and nearly complete salt rejection when run at hot and cold temperatures of 65°C and 25°C, respectively. The PVDF-60 shows a high wetting resistance and stable MD flux of 10.5 l/m2 h over a 50 h test for treating brine solution as the feed (70 g NaCl/l).

scholarly journals A Comparison Study of Brine Desalination using Direct Contact and Air Gap Membrane Distillation

2019 ◽  
Vol 25 (11) ◽  
pp. 47-54
Author(s):  
Ahmed Shamil Khalaf ◽  
Asrar Abdullah Hassan
Keyword(s):  
Flow Rate ◽  
Direct Contact ◽  
Polyvinylidene Fluoride ◽  
Membrane Distillation ◽  
Air Gap ◽  
Feed Flow Rate ◽  
Permeate Flux ◽  
Air Gap Membrane Distillation ◽  
Flat Sheet ◽  
Feed Temperature

Membrane distillation (MD) is a hopeful desalination technique for brine (salty) water. In this research, Direct Contact Membrane Distillation (DCMD) and  Air Gap Membrane Distillation (AGMD) will be used. The sample used is from Shat Al –Arab water (TDS=2430 mg/l). A polyvinylidene fluoride (PVDF) flat sheet membrane was used as a flat sheet form with a plate and frame cell. Several parameters were studied, such as; operation time, feed temperature, permeate temperature, feed flow rate. The results showed that with time, the flux decreases because of the accumulated fouling and scaling on the membrane surface. Feed temperature and feed flow rate had a positive effect on the permeate flux, while permeate temperature had a reverse effect on permeate flux. It is noticeable that the flux in DCMD is greater than AGMD, at the same conditions. The flux in DCMD is 10.95LMH, and that in AGMD is 7.14 LMH.  In AGMD, the air gap layer made a high resistance. Here the temperature transport reduces in the permeate side of AGMD due to the air gap resistance. The heat needed for AGMD is lower than DCMD, this leads to low permeate flux because the temperature difference between the two sides is very small, so the driving force (vapor pressure) is low.                                                                                               

scholarly journals Characterization of the Initial Fouling Layer on the Membrane Surface in a Membrane Bioreactor: Effects of Permeation Drag

Membranes ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 121
Author(s):  
Shengli Wang ◽  
Xin Lu ◽  
Lanhe Zhang ◽  
Jingbo Guo ◽  
Haifeng Zhang
Keyword(s):  
Zeta Potential ◽  
Electron Donor ◽  
Energy Barrier ◽  
Polyvinylidene Fluoride ◽  
Membrane Bioreactor ◽  
Membrane Surface ◽  
Permeate Flux ◽  
Pvdf Membrane ◽  
Operating Modes

In this study, the properties of the initial fouling layer on the membrane surface of a bioreactor were investigated under different operating modes (with or without permeate flux) to improve the understanding of the effect of permeation drag on the formation of the initial fouling layer. It was found that protein was the major component in the two types of initial fouling layers, and that the permeation drag enhanced the tryptophan protein-like substances. The attraction of the initial foulants to the polyvinylidene fluoride (PVDF) membrane was ascribed to the high zeta potential and electron donor component (γ−) of the membrane. Thermodynamic analyses showed that the permeation drag-induced fouling layer possessed high hydrophobicity and low γ−. Due to permeation drag, a portion of the foulants overcame an energy barrier before they contacted the membrane surface, which itself possessed a higher fouling propensity. A declining trend of the cohesive strength among the foulants was found with the increasing development of both fouling layers.

scholarly journals Preparation of an Ultrafiltration (UF) Membrane with Narrow and Uniform Pore Size Distribution via Etching of SiO2 Nano-Particles in a Membrane Matrix

Membranes ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 150
Author(s):  
Bushra Khan ◽  
Sajjad Haider ◽  
Rooha Khurram ◽  
Zhan Wang ◽  
Xi Wang
Keyword(s):  
Pore Size Distribution ◽  
Pore Size ◽  
Size Distribution ◽  
Nano Particles ◽  
Coagulation Bath ◽  
Inversion Method ◽  
Permeate Flux ◽  
Membrane Matrix ◽  
Etched Membrane ◽  
Uniform Pore Size

The UF membrane with a narrow and uniform pore size distribution and a low tendency to foul has significant applications in wastewater treatment. A major hindrance in the preparation of the UF membrane with these features is the lack of a scalable and economical membrane fabrication method. Herein, we devise a new strategy to prepare a high-quality polyvinylidene fluoride/polymethyl acrylate/cellulose acetate (PVDF/PMMA/CA) blend UF membrane via a combination of the etching mechanism with the traditional Loeb–Sourirajan (L-S) phase inversion method. Different concentrations of silicon dioxide (SiO2) nanoparticles (NP) in the membrane matrix were etched by using a 0.2 M hydrofluoric acid (HF) solution in a coagulation bath. This strategy provided the membrane with unique features along with a narrow and uniform pore size distribution (0.030 ± 0.005 μm). The etched membrane exhibits an increase of 2.3 times in pure water flux (PWF) and of 6.5 times in permeate flux(PF), with a slight decrease in rejection ratio (93.2% vs. 97%) when compared to than that of the un-etched membrane. Moreover, this membrane displayed outstanding antifouling ability, i.e., a flux recovery ratio (FRR) of 97% for 1000 mg/L bovine serum albumin (BSA) solution, a low irreversible fouling ratio of 0.5%, and highly enhanced hydrophilicity due to the formation of pores/voids throughout the membrane structure. The aforementioned features of the etched membrane indicate that the proposed method of etching SiO2 NP in membrane matrix has a great potential to improve the structure and separation efficiency of a PVDF/PMMA/CA blend membrane.

Sign in / Sign up

Export Citation Format

Share Document