Preparation and selective adsorption of organic pollutants by an inorganic molecular imprinted polymer

2016 ◽  
Vol 74 (5) ◽  
pp. 1193-1201 ◽  
Author(s):  
Jiaobo Shang ◽  
Yanqun Song ◽  
Chuan Rong ◽  
Yinghui Wang ◽  
Liwei Wang ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Adsorption Process ◽  
Selective Adsorption ◽  
Nitrogen Adsorption ◽  
Molecular Imprinted Polymer ◽  
X Ray Diffraction ◽  
Imprinted Polymer ◽  
X Ray ◽  
Acid Orange Ii ◽  
Adsorption Desorption

A novel inorganic molecular imprinted polymer (MIP) was synthesized by adding Al3+ to the Fe/SiO2 gel with Acid Orange II (AO II) as the template. The MIP was characterized by scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy and nitrogen adsorption-desorption measurement. Compared with the non-imprinted polymer (NIP), the MIP enhanced the adsorption capacity of the target pollutants AO II. The selective adsorption capacity study indicated that the MIP adsorbed more AO II than the interferent Bisphenol A (BPA), which also has the structure of a benzene ring, thus proving the selective adsorption capacity of the MIP for template molecules AO II. In addition, the adsorption of AO II over MIP belonged to the Langmuir type and pseudo-second adsorption kinetics, and Dubinin-Radushkevich model indicates that the adsorption process of AO II over MIP and NIP are both given priority to chemical adsorption. The MIP reusability in performance was demonstrated in at least six repeated cycles.

scholarly journals Preparation of GO/MIL-101(Fe,Cu) composite and its adsorption mechanisms for phosphate in aqueous solution

2021 ◽  
Author(s):  
You Wu ◽  
Zuannian Liu ◽  
Bakhtari Mohammad Fahim ◽  
Junnan Luo
Keyword(s):  
Adsorption Capacity ◽  
Photoelectron Spectroscopy ◽  
Adsorption Mechanism ◽  
Nitrogen Adsorption ◽  
Adsorption Properties ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Adsorption Mechanisms ◽  
Adsorption Desorption

Abstract In this study, MIL-101(Fe), MIL-101(Fe,Cu), and Graphene Oxide (GO) /MIL-101(Fe,Cu) were synthesized to compose a novel sorbent. The adsorption properties of these three MOFs-based composites were compared toward the removal of phosphate. Furthermore, the influencing factors including reaction time, pH, temperature and initial concentration on the adsorption capacity of phosphate on these materials as well as the reusability of the material were discussed. The structure of fabricated materials and the removal mechanism of phosphate on the composite material were analyzed by Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), nitrogen adsorption-desorption analysis and zeta potential. The results show that the maximum adsorption capacity of phosphate by the composite GO/MIL-101(Fe,Cu)-2% was 204.60 mg·g− 1, which is higher than that of MIL-101(Fe,Cu) and MIL-101(Fe). likewise the specific surface area of GO/MIL-101(Fe,Cu)-2% is 778.11 m2/g is higher than that of MIL-101(Fe,Cu) and MIL-101(Fe),which are 747.75 and 510.66m2/g respectively. The adsorption mechanism of phosphate is electrostatic attraction, form coordination bonds and hydrogen bonds. The fabricated material is a promising adsorbent for the removal of phosphate with good reusability.

scholarly journals Adsorption of REEs from Aqueous Solution by EDTA-Chitosan Modified with Zeolite Imidazole Framework (ZIF-8)

2021 ◽  
Vol 22 (7) ◽  
pp. 3447
Author(s):  
Sihan Feng ◽  
Xiaoyu Du ◽  
Munkhpurev Bat-Amgalan ◽  
Haixin Zhang ◽  
Naoto Miyamoto ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Adsorption Process ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
Growth Method ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Multiple Cycles ◽  
Adsorption Desorption

Chitosan (CS) modified with ethylenediamine tetraacetic acid (EDTA) was further modified with the zeolite imidazole framework (ZIF-8) by in situ growth method and was employed as adsorbent for the removal of rare-earth elements (REEs). The material (EDTA–CS@ZIF-8) and ZIF-8 and CS were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscope (SEM), and nitrogen adsorption/desorption experiments (N2- Brunauer–Emmet–Teller (BET)). The effects of adsorbent dosage, temperature, the pH of the aqueous solution, contact time on the adsorption of REEs (La(III), Eu(III), and Yb(III)) by EDTA–CS@ZIF-8 were studied. Typical adsorption isotherms (Langmuir, Freundlich, and Dubinin–Radushkevich (D-R)) were determined for the adsorption process, and the maximal adsorption capacity was estimated as 256.4 mg g−1 for La(III), 270.3 mg g−1 for Eu(III), and 294.1 mg g−1 for Yb(III). The adsorption kinetics results were consistent with the pseudo-second-order equation, indicating that the adsorption process was mainly chemical adsorption. The influence of competing ions on REE adsorption was also investigated. After multiple cycles of adsorption/desorption behavior, EDTA–CS@ZIF-8 still maintained high adsorption capacity for REEs. As a result, EDTA–CS@ZIF-8 possessed good adsorption properties such as stability and reusability, which have potential application in wastewater treatment.

scholarly journals DMAEMA-grafted cellulose as an imprinted adsorbent for the selective adsorption of 4-nitrophenol

Cellulose ◽  
2021 ◽  
Author(s):  
Daning Lang ◽  
Ming Shi ◽  
Xia Xu ◽  
Shixue He ◽  
Chao Yang ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Molecularly Imprinted Polymers ◽  
Competitive Adsorption ◽  
Adsorption Process ◽  
Selective Adsorption ◽  
Selectivity Coefficient ◽  
Environmental Pollutant ◽  
Imprinted Polymer ◽  
Adsorption Desorption ◽  
Kinetics Of

Abstract 4-Nitrophenol is a highly toxic environmental pollutant. It is a challenge to selectively remove it from a mixture of various pollutants. Herein, we report a study on the selective adsorption of 4-nitrophenol by using molecularly imprinted polymers (MIPs). The imprinted polymer was synthesized using cellulose as a framework, onto which, the complex of the imprinting molecule (i.e., 4-nitrophenol) and a candidate material [namely, 2-(dimethylamino)ethyl methacrylate. DMAEMA] was grafted. The obtained MIP showed an excellent adsorption capacity with good selectivity. Also, the adsorption of 4-nitrophenol by the obtained MIP was fast and the adsorbent exhibited good recyclability. The thermodynamics and kinetics of the adsorption process of 4-nitrophenol by MIP was thoroughly studied, where an otherwise-equivalent non-imprinted polymer was used as a control in the experiments. The selectivity of the MIP adsorbent for 4-niteophenol was evaluated by two types of experiments: (1) adsorption experiments in single-component adsorbate systems (containing 4-nitrophenol, 3-nitrophenol, catechol, or hydroquinone), and (2) competitive adsorption experiments in binary adsorbate systems (containing 4-nitrophenol plus either 3-nitrophenol, catechol or hydroquinone). The selectivity coefficient for 4-nitrophenols was twice of those of other phenols (that were all around 2), indicative of the extent of the affinity of MIPs to these phenolic compounds. The recyclability of the adsorbent was evaluated for 5 adsorption–desorption cycles, where the adsorption capacity of the last cycle remained over 90.2% of that of the first cycle. Graphic Abstract

Adsorption Capacity of Y Zeolite Using Organic Solvents such as Adsorbates

2014 ◽  
Vol 805 ◽  
pp. 641-645
Author(s):  
Ana Paula Araújo ◽  
Aline Cadigena Lima Patrício ◽  
Anna Karoline Freires de Sousa ◽  
Mariaugusta Ferreira Mota ◽  
Meiry Glaúcia Freire Rodrigues
Keyword(s):  
Small Molecules ◽  
Adsorption Capacity ◽  
Selective Adsorption ◽  
X Ray Diffraction ◽  
Y Zeolite ◽  
High Adsorption ◽  
X Ray ◽  
Low Concentrations ◽  
Adsorption Of Nitrogen ◽  
Type Zeolite

The zeolites differ from traditional adsorbents for selective adsorption of small molecules, the high adsorption capacity at low concentrations and affinity for organic compounds and unsaturated polar molecules. In this work a Y-type zeolite was synthesized, characterized by x-ray diffraction, scanning electron microscopy and adsorption of nitrogen and subjected to test adsorption capacity where it was found that the Y zeolite has the potential adsorption capacity compared to other materials being studied and marketed.

Application of raw and modified Uruguayan clays to phosphate adsorption for water remediation

MRS Advances ◽  
2018 ◽  
Vol 3 (61) ◽  
pp. 3543-3549
Author(s):  
Pablo González ◽  
Andrea C. De Los Santos ◽  
Jorge R. Castiglioni ◽  
María A. De León
Keyword(s):  
Nitrogen Adsorption ◽  
Pillared Clay ◽  
Water Remediation ◽  
Phosphate Adsorption ◽  
X Ray Diffraction ◽  
Order Model ◽  
Freundlich Model ◽  
X Ray ◽  
First Order ◽  
Adsorption Desorption

ABSTRACTA raw clay from Uruguay was modified with aluminium to obtain an aluminium pillared clay (Al-PILC). The solids were characterized by scanning electron microscopy, X-ray diffraction and nitrogen adsorption-desorption isotherms. The Al-PILC retained the typical laminar structure of montmorillonite. The specific surface area and the microporous volume of the Al-PILC, 235 m2 g-1 and 0.096 cm3 g-1, respectively, were much higher than those of the clay. The phosphate adsorption capacity of the Al-PILC was higher than those of the clay. The phosphate adsorption kinetic followed the pseudo-first-order model for both, the clay and the Al-PILC, and the phosphate adsorption isotherm for the Al-PILC fit the Freundlich model.

scholarly journals Optimasi Ukuran dan Jumlah Pori yang Terbentuk Pada Molacularly Imprinted Polymer (MIP) Nano Karbaril (C12H11NO2)

POSITRON ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 14
Author(s):  
Suci Aprilia ◽  
Erry Koryanti ◽  
Idha Royani
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Ethylene Glycol ◽  
Methacrylic Acid ◽  
Molecular Imprinted Polymer ◽  
X Ray Diffraction ◽  
Imprinted Polymer ◽  
X Ray ◽  
Scanning Electron

Telah dilakukan pembuatan molecular imprinted polymer (MIP) nano karbaril dengan metode cooling-heating. Pembuatan MIP nano karbaril bertujuan untuk mendapatkan material sensor yang potensial dalam aplikasinya. Dalam penelitian ini, bahan aktif karbaril di-milling dengan variasi waktu 10 menit dan 15 menit. Pada proses polimerisasi melibatkan templat nano karbaril, methacrylic acid (MAA) sebagai monomer fungsional, ethylene glycol dimathacrylate (EDMA) sebagai crosslinker, benzoil peroksida (BPO) sebagai inisiator, dan acetonitril sebagai pelarut yang disintesis menggunakan metode cooling-heating. Dengan cara yang sama, non-imprinted polymer (NIP) juga dibuat sebagai polimer kontrol.  NIP merupakan polimer yang dibuat dengan komposisi dan cara yang sama dengan MIP, namun tidak ditambahkan nano karbaril sebagai zat aktif. Pembuangan templat pada proses ekstraksi sangat berperan penting untuk menghasilkan material sensor yang baik. MIP, polimer, dan NIP yang dihasilkan di karakterisasi menggunakan Fourier transform infrared (FTIR) dan sampel terbaik dideteksi lebih lanjut dengan uji x-ray diffraction (X-RD), dan scanning electron microscope (SEM). Hasil FTIR menunjukkan bahwa gugus fungsi spesifik nano karbaril pada NIP tidak tampak bila dibandingkan dengan spektra MIP, dan terjadi penurunan persen transmitansi pada polimer dan peningkatan % transmitansi pada MIP. Hal ini menjelaskan bahwa terjadi penurunan konsentrasi nano karbaril pada MIP setelah proses ektraksi. Hasil X-RD menunjukkan ukuran kristal yaitu 9,16 Å. Hasil SEM menunjukkan bahwa jumlah pori tercetak dengan ukuran ≤100 nm yaitu 383 pori.  Data ini mengindikasikan bahwa MIP nano karbaril potensial untuk diaplikasikan sebagai material sensor.

Structural and surface aspects of thermally treated copper aluminium mixed hydroxides

1991 ◽  
Vol 69 (10) ◽  
pp. 1511-1515 ◽  
Author(s):  
Awad I. Ahmed ◽  
S. E. Samra ◽  
S. A. El-Hakam
Keyword(s):  
Pore Structure ◽  
Copper Content ◽  
Textural Properties ◽  
Nitrogen Adsorption ◽  
Phase Changes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Surface Areas ◽  
Structure Surface ◽  
Adsorption Desorption

CuO–Al2O3 catalysts containing various amounts of copper oxide have been prepared by precipitation. The phase changes were studied by X-ray diffraction. The results obtained revealed that the thermal treatment of solid CuO–Al2O3 at 700 °C produced only crystalline CuO. Heating to 900 °C led to the formation of copper alumina spinel together with unreacted CuO and γ-Al2O3. The spinel content was found to increase with increasing copper content. Nitrogen adsorption–desorption isotherms on the calcined samples have been measured. Surface areas have been calculated and the pore structure analysed. The textural properties of the system were found to depend on both the copper content and the calcination temperature. Key words: CuO, Al2O3 catalysts, structure, surface area, pore structure.

scholarly journals Bulk Versus Surface Modification of Alumina with Mn and Ce Based Oxides for CH4 Catalytic Combustion

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1771 ◽  
Author(s):  
Stefan Neatu ◽  
Mihaela M. Trandafir ◽  
Adelina Stănoiu ◽  
Ovidiu G. Florea ◽  
Cristian E. Simion ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Combustion ◽  
Mixed Oxides ◽  
Sol Gel ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Programmed ◽  
Catalytic Combustion Of Methane ◽  
Adsorption Desorption

This study presents the synthesis and characterization of lanthanum-modified alumina supported cerium–manganese mixed oxides, which were prepared by three different methods (coprecipitation, impregnation and citrate-based sol-gel method) followed by calcination at 500 °C. The physicochemical properties of the synthesized materials were investigated by various characterization techniques, namely: nitrogen adsorption-desorption isotherms, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and H2–temperature programmed reduction (TPR). This experimental study demonstrated that the role of the catalytic surface is much more important than the bulk one. Indeed, the incipient impregnation of CeO2–MnOx catalyst, supported on an optimized amount of 4 wt.% La2O3–Al2O3, provided the best results of the catalytic combustion of methane on our catalytic micro-convertors. This is mainly due to: (i) the highest pore size dimensions according to the Brunauer-Emmett-Teller (BET) investigations, (ii) the highest amount of Mn4+ or/and Ce4+ on the surface as revealed by XPS, (iii) the presence of a mixed phase (Ce2MnO6) as shown by X-ray diffraction; and (iv) a higher reducibility of Mn4+ or/and Ce4+ species as displayed by H2–TPR and therefore more reactive oxygen species.

scholarly journals Core-shell Fe3O4@zeolite NaA as an Adsorbent for Cu2+

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5047
Author(s):  
Jun Cao ◽  
Peng Wang ◽  
Jie Shen ◽  
Qi Sun
Keyword(s):  
Adsorption Capacity ◽  
Adsorption Process ◽  
Core Shell ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ph Values ◽  
Transmission Electron ◽  
Monolayer Adsorption ◽  
Zeolite Naa ◽  
Infrared Spectrometer

Here, using Fe3O4@SiO2 as a precursor, a novel core-shell structure magnetic Cu2+ adsorbent (Fe3O4@zeolite NaA) was successfully prepared. Several methods, namely X-ray diffraction (XRD), Fourier transform infrared spectrometer (FTIR), Transmission electron microscope (TEM), Brunauer Emmett Teller (BET) and vibrating sample magnetometry (VSM) were used to characterize the adsorbent. A batch experiment was conducted to study the Cu2+ adsorption capacity of Fe3O4@zeolite NaA at different pH values, contact time, initial Cu2+ concentration and adsorbent does. It is found that the saturated adsorption capacity of Fe3O4@zeolite NaA on Cu2+ is 86.54 mg/g. The adsorption isotherm analysis shows that the adsorption process of Fe3O4@zeolite NaA to Cu2+ is more consistent with the Langmuir model, suggesting that it is a monolayer adsorption. Adsorption kinetics study found that the adsorption process of Fe3O4@zeolite NaA to Cu2+ follows the pseudo-second kinetics model, which means that the combination of Fe3O4@zeolite NaA and Cu2+ is the chemical chelating reaction. Thermodynamic analysis shows that the adsorption process of Fe3O4@zeolite NaA to Cu2+ is endothermic, with increasing entropy and spontaneous in nature. The above results show that Fe3O4@zeolite NaA is a promising Cu2+ adsorbent.

scholarly journals Effect of the Organobentonite Filler on Structure and Properties of Composites Based on Hydroxyethyl Cellulose

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Olga V. Alekseeva ◽  
Anna N. Rodionova ◽  
Nadezhda A. Bagrovskaya ◽  
Alexander V. Agafonov ◽  
Andrew V. Noskov
Keyword(s):  
Tensile Properties ◽  
Composite Films ◽  
Nitrogen Adsorption ◽  
Hydroxyethyl Cellulose ◽  
X Ray Diffraction ◽  
Ir Spectrometry ◽  
X Ray ◽  
Mechanical Dispersion ◽  
Filling Agent ◽  
Adsorption Desorption

Organobentonite powder was synthesized and characterized using laser diffraction, X-ray diffraction, low-temperature nitrogen adsorption-desorption technique, and dynamic light scattering. Obtained powder was found as material with mesopores. The organobentonite particles were larger than pure bentonite one. Hydroxyethyl cellulose (HEC) was filled with organobentonite particles by mechanical dispersion, and produced composite films were researched by the number of methods. New data relating to structure, tensile properties, and antimicrobial activity of HEC/organobentonite composites were obtained. Using results of X-ray diffraction, the reflections assigned to crystal filler in polymer material were proved. Concentration effect of the filling agent on tensile properties of composite film was revealed. Data of infrared (IR) spectrometry indicated a decrease in the density of hydrogen-bond net in HEC/organobentonite composite as compared with pristine HEC. Using microbiological tests, it was found that the HEC/organobentonite films exhibited bacteriostatic action against S. aureus and fungistatic action against molds.

Sign in / Sign up

Export Citation Format

Share Document