Effects of DMSO and glycerol additives on the property of polyamide reverse osmosis membrane

2016 ◽  
Vol 74 (7) ◽  
pp. 1619-1625 ◽  
Author(s):  
Fengjing Wu ◽  
Xiaojuan Liu ◽  
Chaktong Au
Keyword(s):  
Contact Angle ◽  
Reverse Osmosis ◽  
Water Contact Angle ◽  
Interfacial Polymerization ◽  
Water Flux ◽  
Cross Flow ◽  
Interfacial Free Energy ◽  
Polymerization Process ◽  
Water Contact ◽  
Salt Rejection

The polyamide reverse osmosis (RO) membranes were prepared through interfacial polymerization of m-phenylenediamine (MPD) and trimesoyl chloride (TMC). The use of dimethyl sulfoxide (DMSO) and glycerol as additives for the formation of thin-film composite (TFC) was investigated. We studied the effect of DMSO and glycerol addition on membrane property and RO performance. Microscopic morphology was examined by atomic force microscopy and scanning electron microscopy. The surface hydrophilicity was characterized on the basis of water contact angle and surface solid–liquid interfacial free energy (−ΔGSL). Water flux and salt rejection ability of the membranes prepared with or without the additives were evaluated by cross-flow RO tests. The results reveal that the addition of DMSO and glycerol strongly influences the property of the TFC RO membrane. Compared to the MPD/TMC membrane fabricated without DMSO and glycerol, the MPD/TMC/DMSO/glycerol membrane has a rougher surface and is more hydrophilic, showing smaller water contact angle and larger −ΔGSL value. Without decrease in salt rejection ability, the MPD/TMC/DMSO/glycerol membrane shows water flux significantly larger than that of the MPD/TMC membrane. The unique property of the MPD/TMC/DMSO/glycerol membrane is attributed to the cooperative effect of DMSO and glycerol on membrane structure during the interfacial polymerization process.

scholarly journals Preparation and Characterization of a Hydrophilic Polysulfone Membrane Using Graphene Oxide

2019 ◽  
Vol 2019 ◽  
pp. 1-10 ◽  
Author(s):  
Hoan Thi Vuong Nguyen ◽  
Thu Hong Anh Ngo ◽  
Khai Dinh Do ◽  
Minh Ngoc Nguyen ◽  
Nu Thi To Dang ◽  
...  
Keyword(s):  
Contact Angle ◽  
Graphene Oxide ◽  
Water Contact Angle ◽  
Water Flux ◽  
Feed Solution ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Inversion Method ◽  
Water Contact ◽  
Polysulfone Membrane

In general, the polysulfone (PSf) membranes are popular choices for water treatment because they have high thermal stability and good chemical resistance. On the other hand, the filtration capacity of the polysulfone membrane is limited because of its low water flux and poor antifouling ability, which are caused by the low surface hydrophilicity of the membranes. In this research, blending of graphene oxide (GO) or graphene oxide-titanium dioxide (GO-TiO2) mixture into the polysulfone matrix had been carried out through the phase inversion method to enhance the hydrophilic and antifouling properties. Methods such as energy-dispersive X-ray spectroscopy, scanning electron microscopy, Fourier transform infrared spectroscopy, and water contact angle measurement were used to examine the surface properties of the prepared membranes. Experimental results have led to a conclusion that graphene oxide can be stabilized into prepared membranes, and then, by reducing the water contact angle values, the surface of these membranes becomes hydrophilic, which increases the permeability and the water flux of methylene blue from the aqueous feed solution, improving the membrane’s antifouling resistance.

scholarly journals Innovative Nanostructured Membranes for Reverse Osmosis Water Desalination

2020 ◽  
Author(s):  
Haleema Saleem ◽  
Syed Javaid Zaidi
Keyword(s):  
Reverse Osmosis ◽  
Separation Efficiency ◽  
Interfacial Polymerization ◽  
Water Flux ◽  
Water Desalination ◽  
Selective Layer ◽  
Salt Rejection ◽  
Membrane Performance ◽  
Tfc Membrane ◽  
Ro Membrane

Reverse osmosis (RO) is considered as the most widely utilized technique worldwide for water treatment. However, the commercial thin-film composite (TFC) membranes, which are normally made of polyamide (PA) through interfacial polymerization (IP), still experience certain major issues in performance and fabrication. The spin assisted layer-by-layer (SA-LbL) technique was established for overcoming some drawbacks with commercially available PA membranes. Also, recent investigations have recognized the nanoparticle inclusion into the selective layer as a powerful technique for improving the membrane efficiency. Hence, two different methodologies are presented here to improve the membrane performance, i.e., (1) SA-LbL technique to fabricate TFC membrane by the deposition of alternate ultrathin layers of different polyelectrolytes on polysulfone (PSF) commercial ultrafiltration membrane and (2) the nanoclay incorporation into the membranes during IP process to develop TFC membrane. Two types of nanoclays, cloisite (CS)-15A and montmorillonite (MNT), were incorporated to enhance the separation efficiency. This SA-LbL is an innovative method for the RO membrane manufacture, and has not been described earlier to the best of our knowledge. In addition, this work validated for the first time, the efficiency of the two nanoclays at the PA selective layer in the RO membrane. The membrane performance was evaluated using sodium chloride solution in a cross-flow permeation-testing cell for salt rejection and water flux. The results show significant improvement in water flux and salt rejection. The permeation test of 120 bilayers of poly (allylaminehydrochloride)/poly (vinylsulfate) on PSF substrate showed water flux of 37 L/ (m2.h) and salt rejection of 53%, for a 2000-ppm salt solution feed. The highest water flux of 40 L/m2.h with 80% salt rejection, relative to the control membrane was obtained for the membranes containing nanoclays at 25oC temperature, 40.0 bar pressure and 2000 ppm feed concentration. Thus, our study demonstrated that these TFC membranes are promising, and these novel fabrication techniques are great tool to manufacture the RO membrane.

Fabrication and Properties of the PVDF/PVDF-g-PMMA Blend Hydrophilic Membrane

2011 ◽  
Vol 418-420 ◽  
pp. 639-642
Author(s):  
Tao Yuan ◽  
Jian Qiang Meng ◽  
Guo Rong Cai ◽  
Yu Feng Zhang
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Polyvinylidene Fluoride ◽  
Membrane Surface ◽  
Pure Water ◽  
Water Flux ◽  
Water Contact ◽  
H Nmr ◽  
Membrane Surfaces ◽  
Static Water

An amphiphilic graft copolymer was obtained via atom transfer radical polymerization (ATRP) of methacrylate (MMA) initiated directly by polyvinylidene fluoride (PVDF). Hydrophilic PVDF membranes were prepared by immersion precipitation of PVDF-g-PMMA and PVDF blend solutions. The chemical structure and the molecular weight were characterized by 1H-NMR and GPC. The hydrophilicity of membrane surfaces were characterized by static water contact angle. Top surface and cross-section of membranes were observed by Field Emission Scanning Electron Microscope (FESEM). The results demonstrated the water contact angle of the membrane surface decreased from 89°to 67°, indicating enhanced hydrophilicity; the pure water flux water firstly decreased and then increased up to 1.7 times of the PVDF membrane. The retention of PEG (Mn=6000) could be maintained at 93%-95%.

Long-Term Stable Metal Organic Framework (MOF) Based Mixed Matrix Membranes for Ultrafiltration

2020 ◽  
Author(s):  
Muayad Al-shaeli ◽  
Stefan J. D. Smith ◽  
Shanxue Jiang ◽  
Huanting Wang ◽  
Kaisong Zhang ◽  
...  
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Mixed Matrix Membranes ◽  
Recovery Ratio ◽  
Mixed Matrix ◽  
Water Contact ◽  
Membrane Performance ◽  
Metal Organic ◽  
Matrix Membranes

<p>In this study, novel <a>mixed matrix polyethersulfone (PES) membranes</a> were synthesized by using two different kinds of metal organic frameworks (MOFs), namely UiO-66 and UiO-66-NH<sub>2</sub>. The composite membranes were characterised by SEM, EDX, FTIR, PXRD, water contact angle, porosity, pore size, etc. Membrane performance was investigated by water permeation flux, flux recovery ratio, fouling resistance and anti-fouling performance. The stability test was also conducted for the prepared mixed matrix membranes. A higher reduction in the water contact angle was observed after adding both MOFs to the PES and sulfonated PES membranes compared to pristine PES membranes. An enhancement in membrane performance was observed by embedding the MOF into PES membrane matrix, which may be attributed to the super-hydrophilic porous structure of UiO-66-NH<sub>2</sub> nanoparticles and hydrophilic structure of UiO-66 nanoparticles that could accelerate the exchange rate between solvent and non-solvent during the phase inversion process. By adding the MOFs into PES matrix, the flux recovery ratio was increased greatly (more than 99% for most mixed matrix membranes). The mixed matrix membranes showed higher resistance to protein adsorption compared to pristine PES membranes. After immersing the membranes in water for 3 months, 6 months and 12 months, both MOFs were stable and retained their structure. This study indicates that UiO-66 and UiO-66-NH<sub>2</sub> are great candidates for designing long-term stable mixed matrix membranes with higher anti-fouling performance.</p>

scholarly journals Surface modification of PMMA polymer and its composites with PC61BM fullerene derivative using an atmospheric pressure microwave argon plasma sheet

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Andrzej Sikora ◽  
Dariusz Czylkowski ◽  
Bartosz Hrycak ◽  
Magdalena Moczała-Dusanowska ◽  
Marcin Łapiński ◽  
...  
Keyword(s):  
Contact Angle ◽  
Surface Modification ◽  
Chemical Composition ◽  
Water Contact Angle ◽  
Plasma Sheet ◽  
Atmospheric Pressure ◽  
Argon Plasma ◽  
Fullerene Derivative ◽  
Water Contact ◽  
Pmma Polymer

AbstractThis paper presents the results of experimental investigations of the plasma surface modification of a poly(methyl methacrylate) (PMMA) polymer and PMMA composites with a [6,6]-phenyl-C61-butyric acid methyl ester fullerene derivative (PC61BM). An atmospheric pressure microwave (2.45 GHz) argon plasma sheet was used. The experimental parameters were: an argon (Ar) flow rate (up to 20 NL/min), microwave power (up to 530 W), number of plasma scans (up to 3) and, the kind of treated material. In order to assess the plasma effect, the possible changes in the wettability, roughness, chemical composition, and mechanical properties of the plasma-treated samples’ surfaces were evaluated by water contact angle goniometry (WCA), atomic force microscopy (AFM), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). The best result concerning the water contact angle reduction was from 83° to 29.7° for the PMMA material. The ageing studies of the PMMA plasma-modified surface showed long term (100 h) improved wettability. As a result of plasma treating, changes in the samples surface roughness parameters were observed, however their dependence on the number of plasma scans is irregular. The ATR-FTIR spectra of the PMMA plasma-treated surfaces showed only slight changes in comparison with the spectra of an untreated sample. The more significant differences were demonstrated by XPS measurements indicating the surface chemical composition changes after plasma treatment and revealing the oxygen to carbon ratio increase from 0.1 to 0.4.

scholarly journals Physicochemical Properties and Biocompatibility of Electrospun Polycaprolactone/Gelatin Nanofibers

2021 ◽  
Vol 18 (9) ◽  
pp. 4764
Author(s):  
Wei Lee Lim ◽  
Shiplu Roy Chowdhury ◽  
Min Hwei Ng ◽  
Jia Xian Law
Keyword(s):  
Contact Angle ◽  
Physicochemical Properties ◽  
Water Contact Angle ◽  
Ligament Injury ◽  
Great Promise ◽  
Composition Analysis ◽  
Water Contact ◽  
Tenogenic Differentiation ◽  
Good Biocompatibility ◽  
Tissue Grafts

Tissue-engineered substitutes have shown great promise as a potential replacement for current tissue grafts to treat tendon/ligament injury. Herein, we have fabricated aligned polycaprolactone (PCL) and gelatin (GT) nanofibers and further evaluated their physicochemical properties and biocompatibility. PCL and GT were mixed at a ratio of 100:0, 70:30, 50:50, 30:70, 0:100, and electrospun to generate aligned nanofibers. The PCL/GT nanofibers were assessed to determine the diameter, alignment, water contact angle, degradation, and surface chemical analysis. The effects on cells were evaluated through Wharton’s jelly-derived mesenchymal stem cell (WJ-MSC) viability, alignment and tenogenic differentiation. The PCL/GT nanofibers were aligned and had a mean fiber diameter within 200–800 nm. Increasing the GT concentration reduced the water contact angle of the nanofibers. GT nanofibers alone degraded fastest, observed only within 2 days. Chemical composition analysis confirmed the presence of PCL and GT in the nanofibers. The WJ-MSCs were aligned and remained viable after 7 days with the PCL/GT nanofibers. Additionally, the PCL/GT nanofibers supported tenogenic differentiation of WJ-MSCs. The fabricated PCL/GT nanofibers have a diameter that closely resembles the native tissue’s collagen fibrils and have good biocompatibility. Thus, our study demonstrated the suitability of PCL/GT nanofibers for tendon/ligament tissue engineering applications.

Osteoconductivity of Superhydrophilic Ti- and Zr-Alloy for Biomedical Application

2016 ◽  
Vol 879 ◽  
pp. 2524-2527
Author(s):  
Masazumi Okido ◽  
Kensuke Kuroda
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Strong Influence ◽  
Biomedical Application ◽  
Hydrophobic Surface ◽  
Hydrophilic Surface ◽  
Water Contact ◽  
Zr Alloy ◽  
Zr Alloys

Surface hydrophilicity is considered to have a strong influence on the biological reactions of bone-substituting materials. However, the influence of a hydrophilic or hydrophobic surface on the osteoconductivity is not completely clear. In this study, we produced super-hydrophilic and hydrophobic surface on Ti-and Zr-alloys. Hydrothermal treatment at 180 oC for 180 min. in the distilled water and immersion in x5 PBS(-) brought the super-hydrophilic surface (water contact angle < 10 (deg.)) and heat treatment of as-hydrothermaled the hydrophobic surface. The osteoconductivity of the surface treated samples with several water contact angle was evaluated by in vivo testing. The surface properties, especially water contact angle, strongly affected the osteoconductivity and protein adsorbability, and not the surface substance.

scholarly journals Vertical Orientation of Liquid Crystal on Polystyrene Substituted with n-Alkylbenzoate-p-oxymethyl Pendant Group as a Liquid Crystal Precursor

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2058
Author(s):  
Kyutae Seo ◽  
Hyo Kang
Keyword(s):  
Contact Angle ◽  
Liquid Crystal ◽  
Water Contact Angle ◽  
Polymer Films ◽  
Molar Fraction ◽  
Side Chain ◽  
Pendant Group ◽  
Polymer Modification ◽  
Vertical Orientation ◽  
Water Contact

We synthesized a series of polystyrene derivatives modified with precursors of liquid crystal (LC) molecules via polymer modification reactions. Thereafter, the orientation of the LC molecules on the polymer films, which possess part of the corresponding LC molecular structure, was investigated systematically. The precursors and the corresponding derivatives used in this study include ethyl-p-hydroxybenzoate (homopolymer P2BO and copolymer P2BO#, where # indicates the molar fraction of ethylbenzoate-p-oxymethyl in the side chain (# = 20, 40, 60, and 80)), n-butyl-p-hydroxybenzoate (P4BO), n-hexyl-p-hydroxybenzoate (P6BO), and n-octyl-p-hydroxybenzoate (P8BO). A stable and uniform vertical orientation of LC molecules was observed in LC cells fabricated with P2BO#, with 40 mol% or more ethylbenzoate-p-oxymethyl side groups. In addition, the LC molecules were oriented vertically in LC cells fabricated with homopolymers of P2BO, P4BO, P6BO, and P8BO. The water contact angle on the polymer films can be associated with the vertical orientation of the LC molecules in the LC cells fabricated with the polymer films. For example, vertical LC orientation was observed when the water contact angle of the polymer films was greater than ~86°. Good orientation stability was observed at 150 °C and with 20 J/cm2 of UV irradiation for LC cells fabricated with the P2BO film.

Sign in / Sign up

Export Citation Format

Share Document