scholarly journals DETERMINATION OF REACTION KINETICS USING ONLINE X-RAY DIFFRACTION

2010 ◽  
Vol 8 (3) ◽  
pp. 337-341 ◽  
Author(s):  
Elida Purba
Keyword(s):  
Glutamic Acid ◽  
Reaction Kinetics ◽  
Transformation Process ◽  
X Ray Diffraction ◽  
Concentration Data ◽  
Fixed Temperature ◽  
Exponential Factor ◽  
X Ray ◽  
Acid Reaction ◽  
Xrd Patterns

X-ray diffraction (XRD) is a powerful technique for the study of polymorphism and polymorphic phase transformations. Monitoring of phase transformation directly has been very limited to-date. The XRD system used in this study was used to determine the rate of transformation of pure glutamic acid a form to b form in a solution mediated phase. On every run starting from the pure a form, the transformation process was monitored continuously at fixed temperature, and separate experiments were performed as a function of temperature. The operating temperature was varied from 36 to 57 °C with 10% w/w solid concentration. Data were taken every 200 seconds until the transformation was completed. This paper is concerned with a study of the transformation of the alpha (a) form of L-glutamic acid (L-GA) to the beta (b) form in order to determine the kinetic reaction. The rate constant (k), activation energy (Ea) and pre-exponential factor (A) were obtained. Sensitivity tests were also carried out to examine minimum detection limit when both a and b present in the mixture. In addition, effect of particle size on XRD patterns was also determined. The results show that XRD gives useful information to observe polymorphism for pharmaceutical industry.     Keywords: XRD, polymorphism, glutamic acid, reaction kinetics

scholarly journals Influence of Li2CO3 addition on electrical and magnetic properties of Ni0.6Mg0.4Fe2O4

2020 ◽  
Vol 10 (03) ◽  
pp. 2050003
Author(s):  
M. R. Hassan ◽  
M. T. Islam ◽  
M. N. I. Khan
Keyword(s):  
Magnetic Properties ◽  
Single Phase ◽  
Low Frequency ◽  
Solid State Reaction Method ◽  
Charge Carriers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electrical And Magnetic Properties ◽  
Frequency Regime ◽  
Xrd Patterns

In this research, influence of adding Li2CO3 (at 0%, 2%, 4%, 6%) on electrical and magnetic properties of [Formula: see text][Formula: see text]Fe2O4 (with 60% Ni and 40% Mg) ferrite has been studied. The samples are prepared by solid state reaction method and sintered at 1300∘C for 6[Formula: see text]h. X-ray diffraction (XRD) patterns show the samples belong to single-phase cubic structure without any impurity phase. The magnetic properties (saturation magnetization and coercivity) of the samples have been investigated by VSM and found that the higher concentration of Li2CO3 reduces the hysteresis loss. DC resistivity increases with Li2CO3 contents whereas it decreases initially and then becomes constant at lower value with temperature which indicates that the studied samples are semiconductor. The dielectric dispersion occurs at a low-frequency regime and the loss peaks are formed in a higher frequency regime, which are due to the presence of resonance between applied frequency and hopping frequency of charge carriers. Notably, the loss peaks are shifted to the lower frequency with Li2CO3 additions.

Determination of crystallinity of Chinese handmade papers by means of X-ray diffraction

2020 ◽  
Vol 41 (2) ◽  
pp. 69-86
Author(s):  
Peng Liu ◽  
Hongbin Zhang ◽  
Sinong Wang ◽  
Hui Yu ◽  
Bingjie Lu ◽  
...  
Keyword(s):  
Negative Influence ◽  
X Ray Diffraction ◽  
Cross Sectional ◽  
X Ray ◽  
Eulaliopsis Binata ◽  
Different Types ◽  
Powder Samples ◽  
Xrd Patterns ◽  
Xrd Method

AbstractThe crystallinity indices (CrI) of Chinese handmade papers were investigated using the X-ray diffraction (XRD) method. Four Chinese handmade papers, Yingchun, Zhuma, Yuanshu and Longxucao papers were used as model substrates of mulberry bark, ramie, bamboo and Eulaliopsis binata papers, respectively. Two forms of the paper samples, paper sheets and their comminuted powders, were used in this study. The results showed that their XRD patterns belong to the cellulose-I type and Iβ dominates the cellulose microstructure of these paper samples. Moreover, it was found that the microstructures and CrIs of cellulose of these papers were changed by the grinding treatment. This work suggested that the sheet form of the handmade papers is suitable to determine CrI by XRD, despite the contribution of non-cellulosic components in the papers. The order of CrIs for these paper sheet samples was Yingchun, Zhuma, Longxucao and Yuanshu papers. Besides CrIs, differences in cross-sectional areas of the crystalline zone of cellulose can be used for comparing different types of handmade papers. It was also found that the CrIs and crystallite size of paper cellulose varied between the sheet samples and the powder samples, illustrating that the pulverisation has a negative influence on the microstructure of the handmade papers.

Effects of Different Sintering Temperature on the Microstructure and Piezoelectric Properties of Pb(Nb2/3Zn1/3)x(Zr52Ti48)1-XO3 Ceramics

2014 ◽  
Vol 1061-1062 ◽  
pp. 83-86
Author(s):  
Hong Wu ◽  
De Yi Zheng
Keyword(s):  
Electrical Properties ◽  
Electromechanical Coupling ◽  
Piezoelectric Properties ◽  
Sintering Temperature ◽  
Electromechanical Coupling Coefficient ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ceramic Samples ◽  
Xrd Patterns ◽  
The Relationship

In this paper, the effects of different sintering temperature on the microstructure and piezoelectric properties of Pb(Nb2/3Zn1/3)0.03(Zr52Ti48)0.97O3(PNZZT) ceramic samples were investigated. The Pb(Nb2/3Zn1/3)0.03(Zr52Ti48)0.97O3 ceramics materials was prepared by a conventional mixed oxide method. In the period of the experiment, the relationship between crystallographic phase and microstructure were analyzed by X-ray diffraction(XRD) and scanning electron microscopy(SEM) respectively. The XRD patterns shows that all of the ceramic samples are with a tetragonal perovskite structure. Along with sintering temperature increased and the x is 0.03, the grain size gradually become big. Through this experiment, it has been found that when the x is 0.03 and sintered at 1130°C for 2 h, the grains grow well, the grain-boundary intersection of the sample combined well and the porosity of the ceramics decreased, an excellent comprehensive electrical properties of the Pb(Nb2/3Zn1/3)0.03(Zr52Ti48)0.97O3 samples can be obtained. Its best electrical properties are as follows: dielectric constant (ε) is 1105, dielectric loss(tg) is 0.017, electromechanical coupling coefficient (Kp) is 0.287, piezoelectric constant(d33) is 150PC/N

Thermal-induced transformation of glutamic acid to pyroglutamic acid and self-cocrystallization: a charge–density analysis

2022 ◽  
Vol 78 (2) ◽  
Author(s):  
Sehrish Akram ◽  
Arshad Mehmood ◽  
Sajida Noureen ◽  
Maqsood Ahmed
Keyword(s):  
Hydrogen Bonds ◽  
Glutamic Acid ◽  
Single Crystal ◽  
Diffraction Data ◽  
Density Functional ◽  
Quantitative Estimation ◽  
Topological Analysis ◽  
Pyroglutamic Acid ◽  
X Ray Diffraction ◽  
X Ray

Thermal-induced transformation of glutamic acid to pyroglutamic acid is well known. However, confusion remains over the exact temperature at which this happens. Moreover, no diffraction data are available to support the transition. In this article, we make a systematic investigation involving thermal analysis, hot-stage microscopy and single-crystal X-ray diffraction to study a one-pot thermal transition of glutamic acid to pyroglutamic acid and subsequent self-cocrystallization between the product (hydrated pyroglutamic acid) and the unreacted precursor (glutamic acid). The melt upon cooling gave a robust cocrystal, namely, glutamic acid–pyroglutamic acid–water (1/1/1), C5H7NO3·C5H9NO4·H2O, whose structure has been elucidated from single-crystal X-ray diffraction data collected at room temperature. A three-dimensional network of strong hydrogen bonds has been found. A Hirshfeld surface analysis was carried out to make a quantitative estimation of the intermolecular interactions. In order to gain insight into the strength and stability of the cocrystal, the transferability principle was utilized to make a topological analysis and to study the electron-density-derived properties. The transferred model has been found to be superior to the classical independent atom model (IAM). The experimental results have been compared with results from a multipolar refinement carried out using theoretical structure factors generated from density functional theory (DFT) calculations. Very strong classical hydrogen bonds drive the cocrystallization and lend stability to the resulting cocrystal. Important conclusions have been drawn about this transition.

Effect of Fly Ash and Slag on the Resistance to H2S Attack of Oil Well Cement

2009 ◽  
Vol 79-82 ◽  
pp. 71-74
Author(s):  
Qi Wang ◽  
Lin Qiao ◽  
Peng Song
Keyword(s):  
Fly Ash ◽  
Compression Strength ◽  
Blended Cement ◽  
Oil Well ◽  
X Ray Diffraction ◽  
X Ray ◽  
Curing Period ◽  
Oil Well Cement ◽  
Xrd Patterns ◽  
Well Cement

In this paper, the resistance to H2S attack of pastes made from slag-fly ash blended cement used in oil well (SFAOW) was studied, in which fly ash (FA) was used at replacement dosages of 30% to 60% by weight of slag. Samples of SCOW and SFAOW pastes were demoulded and cured by immersion in fresh water with 2 Mp H2S insulfflation under 130oC for 15 days. After this curing period, compression strength and permeability of the samples were investigated. The reaction mechanisms of H2S with the paste were carried out through a microstructure study, which included the use of x-ray diffraction (XRD) patterns and scanning electron microscope (SEM). Based on the obtained data in this study, incorporation of FA into SCOW results in the comparable effects in the resistance to H2S attack. When the replacement dosage of slag is about 40%, the paste exhibits the best performance on resistance to H2S attack with compression strength 36.58Mp.

STRUCTURE AND MAGNETIC PROPERTIES OF MECHANICAL ALLOYED Mn-15at.%Al

2013 ◽  
Vol 12 (01) ◽  
pp. 1350006
Author(s):  
AHMED E. HANNORA ◽  
FARIED F. HANNA ◽  
LOTFY K. MAREI
Keyword(s):  
Thermal Analysis ◽  
Room Temperature ◽  
Average Crystallite Size ◽  
Al Alloy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Milled Sample ◽  
Powder Samples ◽  
Xrd Patterns ◽  
Method Analysis

Mechanical alloying (MA) method has been used to produce nanocrystallite Mn -15at.% Al alloy. X-ray diffraction (XRD) patterns for the as-milled elemental α- Mn and aluminum powder samples show a mixture of α + β- MnAl phases after 20 h of milling and changes to a dominant β- MnAl phase structure after 50 h. An average crystallite size of 40 nm was determined from Hall–Williamson method analysis after 5 h of milling. Moreover, the thermal analysis results using differential thermal analysis (DTA), suggested a possible phase transformation after 20 h of milling. Isothermal treatments are carried in the temperature range of 450°C to 1000°C. Room-temperature vibrating sample magnetometer (VSM) measurements of the hysteretic response revealed that the saturation magnetization Bs and coercivity Hc for 10 h ball milled sample are ~ 2.1 emu/g and ~ 92 Oe, respectively.

Effects of Indium Incorporation on the Optical Properties of ZnO Films

2006 ◽  
Vol 11-12 ◽  
pp. 159-162 ◽  
Author(s):  
Yong Ge Cao ◽  
Lei Miao ◽  
Sakae Tanemura ◽  
Yasuhiko Hayashi ◽  
Masaki Tanemura
Keyword(s):  
Optical Transmission ◽  
Full Width Half Maximum ◽  
Structural Disorder ◽  
Band Gaps ◽  
Zno Films ◽  
Photoluminescence Spectra ◽  
X Ray Diffraction ◽  
X Ray ◽  
Optical Band Gaps ◽  
Xrd Patterns

Transparent indium-doped ZnO (IZO) films with low In content (<6at%) were fabricated through radio-frequency (rf) helicon magnetron sputtering. Formation of In-Zn-O solid solution was confirmed by X-ray diffraction (XRD) patterns. Incorporation of indium into ZnO films enhances the optical transmission in the visible wavelength. The optical band-gaps slightly increase from 3.25eV (ZnO) to 3.28eV (In0.04Zn0.96O) and to 3.30eV (In0.06Zn0.94O) due to Burstain-Moss effect. The Urbach tail parameter E0, which is believed to be a function of structural disorder, increases from 79meV (ZnO), to 146meV (In0.04Zn0.96O), and to 173meV (In0.06Zn0.94O), which is consistent with increase of Full-Width Half-Maximum (FWHM) in corresponding XRD patterns. Decreasing in crystal quality with increasing indium concentration is also confirmed by photoluminescence spectra.

scholarly journals FTIR and Optical Properties of NiO Doped Cr2O3 Nanopar-ticles Synthesis by Hydrothermal Method

2018 ◽  
Vol 29 (1) ◽  
pp. 168
Author(s):  
Tunis Balassim Hassan
Keyword(s):  
Optical Band Gap ◽  
Average Crystallite Size ◽  
Structural Behavior ◽  
X Ray Diffraction ◽  
Nanopar Ticles ◽  
Hydrothermal Technique ◽  
X Ray ◽  
Cr2o3 Nanoparticles ◽  
Xrd Patterns ◽  
Scanning Electron

Pure and Nickel oxide doped chromium (III) oxide (Cr2O3) nanoparticals are synthesized by hydrothermal technique. The effect of dopant Ni concentration on the structural behavior of Cr2O3 nanoparticles was examined by X-ray diffraction. The average crystallite size of the synthesized nanoparticles was measured from XRD patterns using Scherrer equation and was decreased from 22nm to 12.9 nm with the increasing Nio concentration in Cr2O3 from (0, 0.01, 0.06, and 0.10). Morphologies and compositional elements of the synthesized nanoparticles were observed by the field emission scanning electron microscopy (FESEM) and energy dispersive X-ray (EDX) spectroscopy, respectively. The optical property of the samples was measured by ultraviolet - visible (UV-Vis.) absorption spectroscopy. The observed optical band gap value ranges from 2.3eV to 2.5eV for Ni doped nanoparticles

scholarly journals Fast X-Ray Diffraction (XRD) Tomography for Enhanced Identification of Materials

2021 ◽  
Author(s):  
Airidas Korolkovas ◽  
Alexander Katsevich ◽  
Michael Frenkel ◽  
William Thompson ◽  
Edward Morton
Keyword(s):  
Graphics Processing Unit ◽  
Low Cost ◽  
Photon Counting ◽  
Finite Size ◽  
Processing Unit ◽  
X Ray Diffraction ◽  
X Ray ◽  
Specific Material ◽  
Xrd Patterns ◽  
Graphics Processing

X-ray computed tomography (CT) can provide 3D images of density, and possibly the atomic number, for large objects like passenger luggage. This information, while generally very useful, is often insufficient to identify threats like explosives and narcotics, which can have a similar average composition as benign everyday materials such as plastics, glass, light metals, etc. A much more specific material signature can be measured with X-ray diffraction (XRD). Unfortunately, XRD signal is very faint compared to the transmitted one, and also challenging to reconstruct for objects larger than a small laboratory sample. In this article we analyze a novel low-cost scanner design which captures CT and XRD signals simultaneously, and uses the least possible collimation to maximize the flux. To simulate a realistic instrument, we derive a formula for the resolution of any diffraction pathway, taking into account the polychromatic spectrum, and the finite size of the source, detector, and each voxel. We then show how to reconstruct XRD patterns from a large phantom with multiple diffracting objects. Our approach includes a reasonable amount of photon counting noise (Poisson statistics), as well as measurement bias, in particular incoherent Compton scattering. The resolution of our reconstruction is sufficient to provide significantly more information than standard CT, thus increasing the accuracy of threat detection. Our theoretical model is implemented in GPU (Graphics Processing Unit) accelerated software which can be used to assess and further optimize scanner designs for specific applications in security, healthcare, and manufacturing quality control.

scholarly journals The Effects of Copper Addition on The Structure and Antibacterial Properties of Biomedical Glasses

2020 ◽  
Author(s):  
Leyla Mojtabavi ◽  
Amir Razavi
Keyword(s):  
Antibacterial Properties ◽  
Inhibition Zone ◽  
X Ray Diffraction ◽  
Network Modifier ◽  
X Ray ◽  
E Coli ◽  
Copper Addition ◽  
Xrd Patterns ◽  
Copper Incorporation ◽  
Glass Compositions

AbstractIn this work, we studied the effects of copper incorporation in the composition of bioactive glass. Three different glass compositions were synthesized with 0, 3, and 6 mol% of copper addition. X-Ray Diffraction (XRD) patterns confirmed that an amorphous microstructure was obtained for all three glass compositions. Results from Differential Thermal Analysis (DTA) showed that the copper addition in the glass lowers the glass transition temperature, from 646°C to 590°C when added at 6 mol%. X-ray Photoelectron (XPS) survey and high-resolution scans were performed to study the structural effects of copper addition in the glass. Results indicated that the incorporation of copper changes the ratio of bridging to non-birding oxygens in the structure. Glasses were further analyzed for their structure with Nuclear Magnetic Resonance (NMR) spectroscopy, which indicated that copper acts as a network modifier in the glass composition and copper-containing glasses show a less connected microstructure. Antibacterial efficacy of the glasses was analyzed against E. coli and S. epidermis. Copper-containing glasses showed a significantly higher inhibition zone compared to control glass. The glass with 6 mol% copper, exhibited inhibition zones of 9 and 16mm against E. coli and S. epidermis bacteria, respectively.

Sign in / Sign up

Export Citation Format

Share Document