scholarly journals Temperature-dependent thermal properties of spark plasma sintered alumina

2017 ◽  
Vol 49 (2) ◽  
pp. 117-128 ◽  
Author(s):  
Nouari Saheb ◽  
Umer Hayat
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Room Temperature ◽  
Alumina Powder ◽  
Temperature Dependent ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Sintering Method

In this work, we report temperature-dependent thermal properties of alumina powder and bulk alumina consolidated by spark plasma sintering method. The properties were measured between room temperature and 250?C using a thermal constants analyzer. Alumina powder had very low thermal properties due to the presence of large pores and absence of bonding between its particles. Fully dense alumina with a relative density of 99.6 % was obtained at a sintering temperature of 1400?C and a holding time of 10 min. Thermal properties were found to mainly dependent on density. Thermal conductivity, thermal diffusivity, and specific heat of the fully dense alumina were 34.44 W/mK, 7.62 mm2s-1, and 1.22 J/gK, respectively, at room temperature. Thermal conductivity and thermal diffusivity decreased while specific heat increased with the increase in temperature from room temperature to 250?C.

Thermal Characterization of Carbon-Carbon Composites

2011 ◽  
Author(s):  
Messiha Saad ◽  
Darryl Baker ◽  
Rhys Reaves
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Critical Role ◽  
Carbon Composite ◽  
Flash Method ◽  
Carbon Composites ◽  
Energy Storage Devices ◽  
Graphitized Carbon

Thermal properties of materials such as specific heat, thermal diffusivity, and thermal conductivity are very important in the engineering design process and analysis of aerospace vehicles as well as space systems. These properties are also important in power generation, transportation, and energy storage devices including fuel cells and solar cells. Thermal conductivity plays a critical role in the performance of materials in high temperature applications. Thermal conductivity is the property that determines the working temperature levels of the material, and it is an important parameter in problems involving heat transfer and thermal structures. The objective of this research is to develop thermal properties data base for carbon-carbon and graphitized carbon-carbon composite materials. The carbon-carbon composites tested were produced by the Resin Transfer Molding (RTM) process using T300 2-D carbon fabric and Primaset PT-30 cyanate ester. The graphitized carbon-carbon composite was heat treated to 2500°C. The flash method was used to measure the thermal diffusivity of the materials; this method is based on America Society for Testing and Materials, ASTM E1461 standard. In addition, the differential scanning calorimeter was used in accordance with the ASTM E1269 standard to determine the specific heat. The thermal conductivity was determined using the measured values of their thermal diffusivity, specific heat, and the density of the materials.

Effect of Coating on the Thermal Conductivities of Diamond/Cu Composites Prepared by Spark Plasma Sintering (SPS)

2014 ◽  
Vol 722 ◽  
pp. 25-29 ◽  
Author(s):  
Q.L. Che ◽  
X.K. Chen ◽  
Y.Q. Ji ◽  
Y.W. Li ◽  
L.X. Wang ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Theoretical Prediction ◽  
Volume Fraction ◽  
Interface Reaction ◽  
Copper Matrix ◽  
Bonding Force ◽  
Ti Alloys ◽  
Plasma Sintering ◽  
Spark Plasma

The carbide forming is proposed to improve interfacial bonding between diamond particles and copper-matrix for diamond/copper composites. The volume fraction of diamond and minor titanium are optimized. The microstructures, thermal properties, interface reaction production and its effect of minor titanium on the properties of the composites are investigated. The results show that the bonding force and thermal conductivity of the diamond/Cu-Ti alloys composites is much weaker and lower than that of the coated-diamond/Cu. the thermal conductivity of coated-60 vol. % diamond/Cu composites is 618 W/m K which is 80 % of the theoretical prediction value. The high thermal conductivity has been achieved by forming the titanium carbide at diamond/copper interface to gain a good interface.

Experimental Study on Thermal Properties of Hollow Sphere Structures

2021 ◽  
Vol 407 ◽  
pp. 185-191
Author(s):  
Josef Tomas ◽  
Andreas Öchsner ◽  
Markus Merkel
Keyword(s):  
Thermal Conductivity ◽  
Experimental Study ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Hollow Sphere ◽  
Plane Source ◽  
Source Method ◽  
Transient Plane Source ◽  
Transient Plane Source Method

Experimental analyses are performed to determine thermal conductivity, thermal diffusivity and volumetric specific heat with transient plane source method on hollow sphere structures. Single-sided testing is used on different samples and different surfaces. Results dependency on the surface is observed.

scholarly journals Compressive strength and thermal properties of spark plasma sintered Al-Al2O3 nanocomposite

2018 ◽  
Vol 50 (1) ◽  
pp. 1-14 ◽  
Author(s):  
Nouari Saheb ◽  
Muhammad Khan
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Thermal Properties ◽  
Yield Strength ◽  
Coefficient Of Thermal Expansion ◽  
Testing Machine ◽  
Thermal Constant ◽  
Compressive Properties ◽  
Plasma Sintering ◽  
Spark Plasma

In this work, compressive and thermal properties of aluminum, milled aluminum, and Al-10Al2O3 composite processed via ball milling (BM) and spark plasma sintering (SPS) were investigated. The microstructural features of powders and sintered samples were characterized using optical and scanning electron microscopy. A universal testing machine was used to determine the compressive properties of the consolidated samples. The thermal conductivity and coefficient of thermal expansion of the developed materials were characterized using a hot disc thermal constant analyzer and a dilatometer, respectively. The Al-10Al2O3 composite possessed hardness of 1309.7 MPa, yield strength of 311.4 MPa, and compressive strength of 432.87 MPa compared to hardness of 326.3 MPa, yield strength of 74.33 MPa, and compressive strength of 204.43 MPa for aluminum. The Al-10Al2O3 composite had thermal conductivity value 81.42 W/mK compared to value of 198.09 W/mK for aluminum. In the temperature range from 373 K to 723 K, the composite had lower CTEs ranging from 10 ? 10?6 to 22 ? 10?6/K compared to 20 ? 10?6 to 30 ? 10?6/K for aluminum.

Influence of Mesocarp Fibre Inclusion on Thermal Properties of Foamed Concrete

2021 ◽  
Vol 87 (1) ◽  
pp. 1-11
Author(s):  
Siti Shahirah Suhaili ◽  
Md Azree Othuman Mydin ◽  
Hanizam Awang
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Volume Fraction ◽  
Thermal Constant ◽  
Volume Fractions ◽  
Foamed Concrete

The addition of mesocarp fibre as a bio-composite material in foamed concrete can be well used in building components to provide energy efficiency in the buildings if the fibre could also offer excellent thermal properties to the foamed concrete. It has practical significance as making it a suitable material for building that can reduce heat gain through the envelope into the building thus improved the internal thermal comfort. Hence, the aim of the present study is to investigate the influence of different volume fractions of mesocarp fibre on thermal properties of foamed concrete. The mesocarp fibre was prepared with 10, 20, 30, 40, 50 and 60% by volume fraction and then incorporated into the 600, 1200 and 1800 kg/m3 density of foamed concrete with constant cement-sand ratio of 1:1.5 and water-cement ratio of 0.45. Hot disk thermal constant analyser was used to attain the thermal conductivity, thermal diffusivity and specific heat capacity of foamed concrete of various volume fractions and densities. From the experimental results, it had shown that addition of mesocarp fibre of 10-40% by volume fraction resulting in low thermal conductivity and specific heat capacity and high the thermal diffusivity of foamed concrete with 600 and 1800 kg/m3 density compared to the control mix while the optimum amount of mesocarp fibre only limit up to 30% by volume fraction for 1200 kg/m3 density compared to control mix. The results demonstrated a very high correlation between thermal conductivity, thermal diffusivity and specific heat capacity which R2 value more than 90%.

Thermal Properties of Tungsten SRM’S 730 and 799

1978 ◽  
Vol 100 (2) ◽  
pp. 330-333 ◽  
Author(s):  
R. E. Taylor
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
Thermal Properties ◽  
High Temperature ◽  
Thermal Diffusivity ◽  
Thermophysical Properties ◽  
Room Temperature ◽  
Standard Material ◽  
International Program ◽  
Sintered Tungsten

Samples of sintered and arc-cast tungsten are available from NBS as thermal conductivity (SRM 730) and electrical resistivity (SRM 799) standards for the temperature range from 4 to 3000K. NBS recommended values for these properties above room temperature are based on results of various researchers during a previous international program which included arc-cast and sintered tungsten. The sintered tungsten used in this program was found to be unsuited for use as a standard material due to inhomogeneity and high temperature instability. The present paper gives results at high temperatures for thermal conductivity, electrical resistivity, specific heat, thermal diffusivity and Wiedemann-Franz-Lorenz ratio for a sample of the NBS sintered tungsten using the Properties Research Laboratory’s multiproperty apparatus. These results are compared to values recommended by the Thermophysical Properties Research Center, NBS, and an international program.

Enhanced thermoelectric properties in PbTe Nanocomposites

2009 ◽  
Vol 1166 ◽  
Author(s):  
Hillary Kirby ◽  
Joshua Martin ◽  
Anuja Datta ◽  
Lidong Chen ◽  
George S. Nolas
Keyword(s):  
Thermoelectric Properties ◽  
Room Temperature ◽  
Room Temperature Resistivity ◽  
Phase Reaction ◽  
Conductivity Measurements ◽  
Temperature Dependent ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Temperature Dependent Thermal Conductivity ◽  
Temperature Resistivity

AbstractDimensional nanocomposites of PbTe with varying carrier concentrations were prepared from undoped and Ag doped PbTe nanocrystals synthesized utilizing an alkaline aqueous solution-phase reaction. The nanocrystals were densified by Spark Plasma Sintering (SPS) for room temperature resistivity, Hall, Seebeck coefficient, and temperature dependent thermal conductivity measurements. The nanocomposites show an enhancement in the thermoelectric properties compared to bulk PbTe with similar carrier concentrations, thus demonstrating a promising approach for enhanced thermoelectric performance.

Effect of CaO on Thermal Conductivities of Mg and Mg-Zn Alloys

2014 ◽  
Vol 783-786 ◽  
pp. 437-442 ◽  
Author(s):  
Gun Young Oh ◽  
Dae Guen Kim ◽  
Young Gyu Yoo ◽  
Young Ok Yoon ◽  
Shae K. Kim ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Mechanical Property ◽  
Thermal Properties ◽  
Specific Heat ◽  
Room Temperature ◽  
Die Casting ◽  
Steel Mold ◽  
Process Ability ◽  
Zn Alloys ◽  
Thermal Conductivities

The thermal conductivities of binary Mg-CaO and Mg-Zn, and ternary Mg-Zn-CaO alloys have been investigated by evaluating the effect of CaO on pure Mg and Mg-Zn alloys, with an emphasis to develop a new Mg alloy by compromising thermal conductivity, process-ability and mechanical property. The Mg alloys specimens were prepared by casting into a steel mold and then by machining. The thermal conductivities of the alloys were determined by evaluating the thermal properties of specific heat and diffusivity, from room temperature to 200 °C. OM, SEM, and EDS were used to analyze the microstructures and phases. The fluidity was also investigated by using a spiral fluidity mold for improved process-ability during actual die casting.

Thermal Properties of Diamond-Particle-Dispersed Cu-Matrix-Composites Fabricated by Spark Plasma Sintering (SPS)

2010 ◽  
Vol 638-642 ◽  
pp. 2115-2120 ◽  
Author(s):  
Kiyoshi Mizuuchi ◽  
Kanryu Inoue ◽  
Yasuyuki Agari ◽  
Shinji Yamada ◽  
Motohiro Tanaka ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Spark Plasma Sintering ◽  
Packing Density ◽  
Coefficient Of Thermal Expansion ◽  
Diamond Particle ◽  
Holding Time ◽  
Matrix Composites ◽  
Plasma Sintering ◽  
Spark Plasma

Diamond-particle-dispersed copper (Cu) matrix composites were fabricated from Cu-coated diamond particles by spark plasma sintering (SPS) process, and the microstructure and thermal properties of the composites fabricated were examined. These composites can well be consolidated in a temperature range between 973K and 1173K and scanning electron microscopy detects no reaction at the interface between the diamond particle and the Cu matrix. The relative packing density of the diamond-Cu composite increases with increasing sintering temperature and holding time, reaching 99.2% when sintered at a temperature of 1173K for a holding time of 2.1ks. Thermal conductivity of the diamond-Cu composite containing 43.2 vol. % diamond increases with increasing relative packing density, reaching a maximum (654W/mK) at a relative packing density of 99.2%. This thermal conductivity is 83% the theoretical value estimated by Maxwell-Eucken equation. The coefficient of thermal expansion of the composites falls in the upper line of Kerner’s model, indicating strong bonding between the diamond particle and the Cu matrix in the composite.

Thermoelectrical properties of α phase and γ phase NaxCo2O4 ceramics prepared by spark plasma sintering method

2013 ◽  
Vol 1490 ◽  
pp. 57-62 ◽  
Author(s):  
Natsuko Mikami ◽  
Keishi Nishio ◽  
Koya Arai ◽  
Tatsuya Sakamoto ◽  
Masahiro Minowa ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Spark Plasma Sintering ◽  
Figure Of Merit ◽  
Dimensionless Figure Of Merit ◽  
Α Phase ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Sintering Method ◽  
Acid Compound

ABSTRACTThe thermoelectrical properties of α and γ phases of NaxCo2O4 having different amounts of Na were evaluated. The γ NaxCo2O4 samples were synthesized by thermal decomposition in a metal-citric acid compound, and the α NaxCo2O4 samples were synthesized by self-flux processing. Dense bulk ceramics were fabricated using spark plasma sintering (SPS), and the sintered samples were of high density and highly oriented. The thermoelectrical properties showed that γ NaxCo2O4 had higher electrical conductivity and lower thermal conductivity compared with α NaxCo2O4 and that α NaxCo2O4 had a larger Seebeck coefficient. These results show that γ NaxCo2O4 has a larger power factor and dimensionless figure of merit, ZT, than α NaxCo2O4.

Sign in / Sign up

Export Citation Format

Share Document