Degassing Parameters for High-Performance Working Areas at the Anexplored Mine Fields

2021 ◽  
pp. 63-68
Author(s):  
V.S. Zaburdayev ◽  
Keyword(s):  
High Performance ◽  
Methane Content ◽  
Geological Exploration ◽  
Coal Seams ◽  
Good Convergence ◽  
Methane Release ◽  
Working Face ◽  
Technical Factors ◽  
Predicted Values ◽  
The Relationship

Conditions of the coal seams bedding at the mines of Kuzbass and Vorkutskoye deposits, their natural methane content and coal grades are studied in the article. Performance of shearers and the natural degassing effect of the second working on the change in the methane content of the massif in the coal mining zone are evaluated. Dependence is established concerning the coefficient of coal seams natural degassing on the thickness of the mined seam. The influence of natural and mining-technical factors on the efficiency of second working and degassing parameters were studied. The relationship is revealed between the natural methane content of coal seams with the yield index of the volatile substances contained in the coals of various grades. The relationship is defined related to the intensity of the initial methane release from the coal mass to the reservoir degassing wells depending on the natural methane content of the reservoir with the outgoing air flow. Comparison of the data obtained during geological exploration works, and the predicted values calculated based on the identified dependencies showed their good convergence. The dependences were revealed concerning the zones of intense methane release in the degassing wells on the thickness of the inter-layer of the unloaded adjacent layers in the roof and soil of the working layer in the process of moving the working face. This information allows to select the optimal mode of wells functioning for extracting methane-air mixtures suitable for utilization in the unexplored mine fields. Recommended coefficients of degassing of the methane emission sources were determined for ensuring the planned productivity of the working face with the view to ensure its safety on the gas factor.

scholarly journals A continuous conversion technology from top coal caving into multi-slice mining for thick bifurcated coal seams

2021 ◽  
Author(s):  
Xuejie Deng ◽  
Hao Liu ◽  
Jianye Feng ◽  
Yu Li ◽  
Benjamin de Wit
Keyword(s):  
Stable Phase ◽  
Coal Seams ◽  
Mining Technology ◽  
Working Face ◽  
Immediate Roof ◽  
Lower Slice ◽  
Mining Methods ◽  
The Relationship ◽  
Slice Mining ◽  
Conversion Technology

Abstract This paper presents a mining technology that enables the continuous conversion from top coal caving (TCC) to multi-slice mining (MSM). The technology helps operations overcome challenges with mining thick bifurcated coal seams, particularly the challenge of rock-parting seams affecting the caving of TCC mining methods. Findings show that the relationship between the rock-parting thickness and the caveability of top coal can be divided into 3 phases, including a complete caving phase, a transition phase, and a stable phase. This continuous conversion technology was applied in the Zhongwei Coal Mine in which TCC was used to extract the initial 260 m of the study area where the rock-parting seam was relatively thin before a transition to MSM was made due to the rock-parting seam becoming significantly thicker. The continuous conversion to MSM involved the working face advancing upward at an angle of 10 degrees until the rock-parting seam could serve as the immediate floor for the upper slice of the coal seam. The rock-parting seam floor also acted as the immediate roof for the working face of the subsequently mined lower slice. The application of this continuous conversion mining technology obtained good application results.

ANALYSIS OF THE INFLUENCE OF DIMENSIONS OF THE ROPE MIDWATER TRAWLS ON THEIR PERFORMANCE SUBJECT TO GEOMETRIC PROPERTIES OF CONE SHELLS

2017 ◽  
pp. 25-33
Author(s):  
Alexander Vasilievich Dvernik
Keyword(s):  
Surface Properties ◽  
Conical Shell ◽  
Side Surface ◽  
Theoretic Analysis ◽  
Good Convergence ◽  
Large Size ◽  
Quality Coefficient ◽  
Geometric Quality ◽  
The Relationship ◽  
Parameters Calculation

The article studies different shell constructions of mid-water trawls and their properties. The problem settled is suggested to be solved taking into account real geometric interrelations between spacious and surface properties of cone shells. The author suggests to accept a so-called geometric quality coefficient as a criterion of the properties of a conical shell, which represents the ratio of the shell to the area of its side surface and by analogy to use it to the shell of the trawl. The relationship between the trawl dimensions and geometric quality coefficient have been studied. Comparing these figures with the actual characteristics of trawls showed good convergence. According to the results of theoretic analysis and parameters calculation, trawl large-size shells will always have advantages in geometric characteristics over mid-size and, especially, small-size shells. The results of the analysis can be used for approximate calculations of the parameters of the trawl and justification of ways to improve the performance of existing mid-water trawls.

A FORECAST OF PRODUCTIVE LONGEVITY OF HOLSTEIN COWS BY INDIRECT SIGNS

2020 ◽  
Author(s):  
З.С. САНОВА
Keyword(s):  
Correlation Coefficient ◽  
Aging Process ◽  
Direct Relationship ◽  
Stability Index ◽  
Age At First Calving ◽  
Group I ◽  
Predicted Values ◽  
The Stability ◽  
Relationship Of ◽  
The Relationship

В статье представлены материалы о взаимосвязи продолжительности продуктивного использования коров с характеристикой устойчивости к деградации, с возрастом отела и удоем. В исследованной, разнородной по происхождению, группе животных для прогноза продуктивного периода коров, обусловленного устойчивостью к деградации и возрастом первого отела, пригодно уравнение регрессии, аргументами в котором являются индекс устойчивости, возраст первого отела в первой и второй степенях. Коэффициент корреляции межу предсказанными значениями продуктивного периода и его фактическими величинами в I группе составляет 0,502, во II - 0,604. При этом крайние варианты прогнозируются со статистическими ошибками 5 мес при оценке индекса устойчивости по 2 лактациям и 4,1 мес по 3, а средние варианты, соответственно, 1,6 и 1,51 мес. Индекс устойчивости к процессу старения является важной характеристикой биологических особенностей коров, определяющий их продуктивное долголетие. Его оценка по первым 2 и 3 лактациям имеет прямолинейную связь с продуктивным периодом (r=0,4109 и r=0,5270), соответственно. Зависимость продуктивного периода от возраста первого отела криволинейная — с увеличением возраста первого отела сокращается срок продуктивного использования, при возрасте первого отела более 1400 дней срок продуктивного использования колеблется от 1,33 до 1,41 лактации. Коэффициент корреляции между этими характеристиками коров составляет - 0,2164 в I и - 0,2620 во II группах. The article presents materials about the relationship of the duration of productive use of cows with the characteristic of resistance to degradation, with the age of calving and milk yield. In the studied group of animals, which is heterogeneous in origin, the regression equation is suitable for predicting the productive period of cows due to resistance to degradation and the age of the first calving, the arguments of which are the stability index, the age of the first calving in the first and second degrees. The correlation coefficient between the predicted values of the productive period and its actual values in group I is 0.502, in group II - 0.604. At the same time, the extreme variants are predicted with statistical errors of 5 months when evaluating the stability index for 2 lactations and 4.1 months for 3, and the average variants, respectively, are 1.6 and 1.51 months. The index of resistance to the aging process is an important characteristic of the biological characteristics of cows, which determines their productive longevity. Its estimate for the first 2 and 3 lactations has a direct relationship with the productive period (r=0.4109 and r=0.5270), respectively. The dependence of the productive period age at first calving curvilinear with increasing age at first calving reduces the time to productive use, while age at first calving of more than 1400 days, the period of productive use ranges from 1.33 to 1.41 lactation. The correlation coefficient between these characteristics of cows is-0.2164 in I and-0.2620 in II groups.

scholarly journals Comprehensive technical support for safe mining in ultra-close coal seams: A case study

2021 ◽  
pp. 014459872110093
Author(s):  
Wei Zhang ◽  
Jiawei Guo ◽  
Kaidi Xie ◽  
Jinming Wang ◽  
Liang Chen ◽  
...  
Keyword(s):  
Coal Seam ◽  
Technical Support ◽  
Surrounding Rock ◽  
Coal Seams ◽  
Deformation Control ◽  
Hard Roof ◽  
Working Face ◽  
Close Coal Seams ◽  
Safe Mining

In order to mine the coal seam under super-thick hard roof, improve the utilization rate of resources and prolong the remaining service life of the mine, a case study of the Gaozhuang Coal Mine in the Zaozhuang Mining Area has been performed in this paper. Based on the specific mining geological conditions of ultra-close coal seams (#3up and #3low coal seams), their joint systematic analysis has been performed, with the focus made in the following three aspects: (i) prevention of rock burst under super-thick hard roof, (ii) deformation control of surrounding rock of roadways in the lower coal seam, and (iii) fire prevention in the goaf of working face. Given the strong bursting tendency observed in upper coal seam and lower coal seam, the technology of preventing rock burst under super-thick hard roof was proposed, which involved setting of narrow section coal pillars to protect roadways and interleaving layout of working faces. The specific supporting scheme of surrounding rock of roadways in the #3low1101 working face was determined, and the grouting reinforcement method of local fractured zones through Marithan was further proposed, to ensure the deformation control of surrounding rock of roadways in lower coal seams. The proposed fire prevention technology envisaged goaf grouting and spraying to plug leaks, which reduced the hazard of spontaneous combustion of residual coals in mined ultra-close coal seams. The technical and economic improvements with a direct economic benefit of 5.55 million yuan were achieved by the application of the proposed comprehensive technical support. The research results obtained provide a theoretical guidance and technical support of safe mining strategies of close coal seams in other mining areas.

scholarly journals Micromechanism of the Breakage of Two Spherical Gypsum Particles under Normal–Tangential Contact Conditions

2021 ◽  
Vol 11 (9) ◽  
pp. 4039
Author(s):  
Yiran Niu ◽  
Lin Li ◽  
Yanwei Zhang ◽  
Shicai Yu ◽  
Jian Zhou
Keyword(s):  
Tangential Force ◽  
Coarse Grained ◽  
Spherical Particles ◽  
Contact Conditions ◽  
Normal Contact ◽  
Tangential Contact ◽  
Theoretical Predictions ◽  
Tangential Forces ◽  
Predicted Values ◽  
The Relationship

Contact breakage of particles makes a large difference in the strength of coarse-grained soils, and exploring the characteristics within the process of the breakage is of great significance. Ignoring the influence of particle shape, the micromechanism of two spherical particles breaking under normal–tangential contact conditions was investigated theoretically and experimentally. Through theoretical analysis, the breakage form, the shape and size of the conical core, and the relationship between the normal and tangential forces at crushing were predicted. Particle contact tests of two gypsum spheres were carried out, in which the breakage forms, features of the conical cores and the normal and tangential forces at crushing were recorded for comparison with the predicted values. The test results and the theoretical predictions showed good agreement. Both the analysis and test demonstrate that the presence of tangential forces causes the conical core to assume the shape of an oblique cone, and the breakage form to change. Moreover, with increasing normal contact force, the tangential force needed for crushing increases gradually first and then decreases suddenly.

scholarly journals The Relationship between Learning Styles and Academic Performance: Consistency among Multiple Assessment Methods in Psychology and Education Students

2021 ◽  
Vol 13 (6) ◽  
pp. 3341
Author(s):  
Jesús Maya ◽  
Juan F. Luesia ◽  
Javier Pérez-Padilla
Keyword(s):  
Early Childhood ◽  
Academic Performance ◽  
Learning Styles ◽  
Primary Education ◽  
High Performance ◽  
Multiple Choice ◽  
Assessment Methods ◽  
Theory And Practice ◽  
Education Students ◽  
The Relationship

Universities strive to ensure quality education focused on the diversity of the student body. According to experiential learning theory, students display different learning preferences. This study has a three-fold objective: to compare learning styles based on personal and educational variables, to analyze the association between learning styles, the level of academic performance, and consistency of performance in four assessment methods, and to examine the influence of learning dimensions in students with medium-high performance in the assessment methods. An interdisciplinary approach was designed involving 289 psychology, early childhood education and primary education students at two universities in Spain. The Learning Style Inventory was used to assess learning styles and dimensions. The assessment methods used in the developmental psychology course included the following question formats: multiple-choice, short answer, creation-elaboration and an elaboration question on the relationship between theory and practice. Univariate analysis, multivariate analysis, and binomial logistic models were computed. The results reveal Psychology students to be more assimilative (theoretical and abstract), while early childhood and primary education students were evenly distributed among styles and were more divergent and convergent (practical) in absolute terms. In addition, high scores in perception (abstract conceptualization) were associated with a high level of performance on the multiple-choice tests and the elaboration question on the relationship between theory and practice. Abstract conceptualization was also associated with medium-high performance in all assessment methods and this variable predicted consistent high performance, independent of the assessment method. This study highlights the importance of promoting abstract conceptualization. Recommendations for enhancing this learning dimension are presented.

scholarly journals Relationship between Plasma Trimethylamine N-Oxide Levels and Renal Dysfunction in Patients with Hypertension

2021 ◽  
pp. 1-12
Author(s):  
Jia Zhou ◽  
Dingkun Wang ◽  
Bingong Li ◽  
Xuelian Li ◽  
Xingjun Lai ◽  
...  
Keyword(s):  
Blood Pressure ◽  
Kidney Disease ◽  
Renal Dysfunction ◽  
High Performance ◽  
Characteristic Curve ◽  
Area Under The Curve ◽  
Hypertensive Patients ◽  
Ckd Stage ◽  
Liquid Chromatography Tandem Mass ◽  
The Relationship

<b><i>Introduction:</i></b> Trimethylamine N-oxide (TMAO) is a metabolite produced by gut bacteria. Although increased TMAO levels have been linked to hypertension (HTN) and chronic kidney disease (CKD) with poor prognosis, no clinical studies have directly addressed the relationship between them. In this study, we investigated the relationship between TMAO and renal dysfunction in hypertensive patients. <b><i>Methods:</i></b> We included healthy controls (<i>n</i> = 50), hypertensive patients (<i>n</i> = 46), and hypertensive patients with renal dysfunction (<i>n</i> = 143). Their blood pressure values were taken as the highest measured blood pressure. Renal function was evaluated using the estimated glomerular filtration rate. Plasma TMAO levels were measured using high-performance liquid chromatography tandem mass spectrometry. <b><i>Results:</i></b> We found significant differences in plasma TMAO levels among the 3 groups (<i>p</i> &#x3c; 0.01). The plasma TMAO of patients with HTN was significantly higher than that of healthy people, and the plasma TMAO of patients with HTN complicated by renal dysfunction was significantly higher than either of the other groups. Patients in the highest TMAO quartile were at a higher risk of developing CKD stage 5 than those in the lowest quartile. In the receiver operating characteristic curve, the area under the curve of TMAO combined with β 2-macroglobulin for predicting renal dysfunction in patients with HTN was 0.85 (95% confidence interval 0.80–0.90). <b><i>Conclusion:</i></b> An elevated TMAO level reflects higher levels of HTN and more severe renal dysfunction. TMAO, combined with β 2-macroglobulin levels, may assist in diagnosing CKD in hypertensive patients. Plasma TMAO has predictive value for early kidney disease in hypertensive patients.

scholarly journals Changes in Optical Properties upon Dye–Clay Interaction: Experimental Evaluation and Applications

Nanomaterials ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 197
Author(s):  
Giorgia Giovannini ◽  
René M. Rossi ◽  
Luciano F. Boesel
Keyword(s):  
Optical Properties ◽  
Hybrid Materials ◽  
High Performance ◽  
Fluorescent Properties ◽  
Chemical Mechanisms ◽  
Strong Electrostatic Interaction ◽  
Potential Applications ◽  
Photochemical Properties ◽  
Physical And Chemical ◽  
The Relationship

The development of hybrid materials with unique optical properties has been a challenge for the creation of high-performance composites. The improved photophysical and photochemical properties observed when fluorophores interact with clay minerals, as well as the accessibility and easy handling of such natural materials, make these nanocomposites attractive for designing novel optical hybrid materials. Here, we present a method of promoting this interaction by conjugating dyes with chitosan. The fluorescent properties of conjugated dye–montmorillonite (MMT) hybrids were similar to those of free dye–MMT hybrids. Moreover, we analyzed the relationship between the changes in optical properties of the dye interacting with clay and its structure and defined the physical and chemical mechanisms that take place upon dye–MMT interactions leading to the optical changes. Conjugation to chitosan additionally ensures stable adsorption on clay nanoplatelets due to the strong electrostatic interaction between chitosan and clay. This work thus provides a method to facilitate the design of solid-state hybrid nanomaterials relevant for potential applications in bioimaging, sensing and optical purposes.

Sign in / Sign up

Export Citation Format

Share Document