scholarly journals Engineering Properties of Volcanic Tuff from the Western Part of Yemen

2018 ◽  
Vol 22 (2) ◽  
pp. 81
Author(s):  
Adnan A. Barahim ◽  
Ibrahim A. Al-Akhaly ◽  
Is'haq R. Shamsan
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Specific Gravity ◽  
Water Absorption ◽  
Uniaxial Compressive Strength ◽  
Void Ratio ◽  
Engineering Properties ◽  
Dry Density ◽  
Dimension Stone ◽  
Volcanic Tuff

This paper deals with a study of the physical and mechanical characteristics of volcanic tuff and ignimbrite from six quarries located at different areas in the western part of Yemen (Manakha, Jahran, Bakhran, Dar Al-Hanash, Abaser and Soraifa). In the region, volcanic tuffs and ignimbrite are locally known by their location names and have been used as solid masonry and cladding stones. All the investigated pyroclastic rocks belong to the Tertiary volcanic. The standard physical and mechanical tests (void ratio, porosity, density, specific gravity, water absorption, uniaxial compressive strength and tensile strength) were carried out on the tuff and ignimbrite samples collected from different parts of the region. Laboratory tests revealed that the void ratio average values range between 0.12 and 0.37, the porosity ranges between 10.57 and 27.12%, the dry density ranges between 1.66 and 2.25 gm/cm3, specific gravity ranges from 1.45 to 1.94, and water absorption ranges from 4.69 to 16.39%. The measured uniaxial compressive strength values range from 24 to 68 MPa, and the tensile strength values range between 4 and 10 MPa. These tuffs and ignimbrites generally are light green, gray, beige, or yellowish in color. With these colors they are favoured for building, coating and decorative stone. This paper concludes that the studied stones have acceptable to good properties as dimension stone. Jahrani and Manakhi tuffs are the best quality, whereas Hanashi ignimbrite is of poorer quality.

scholarly journals Partial Replacement of Cement with Waste Paper Sludge Ash

2021 ◽  
Vol 9 (11) ◽  
pp. 1975-1983
Author(s):  
Shahid Bashir
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Water Absorption ◽  
Cement Industry ◽  
Waste Paper ◽  
Partial Replacement ◽  
Dry Density ◽  
Paper Sludge ◽  
Paper Sludge Ash ◽  
Sludge Ash

Abstract: Cement production is one of the sources that emit carbon dioxide, in addition to deforestation and combustion of fossil fuels also leads to ill effects on environment. The global cement industry accounts for 7% of earth’s greenhouse gas emission. To enhance the environmental effects associated with cement manufacturing and to constantly deplore natural resources, we need to develop other binders to make the concrete industry sustainable. This work offers the option to use waste paper sludge ash as a partial replacement of cement for new concrete. In this study cement in partially replaced as 5%, 10%, 15% and 20% by waste paper sludge ash in concrete for M25 mix and tested for compressive strength, tensile strength, water absorption and dry density up to the age of 28days and compared it with conventional concrete, based on the results obtained, it is found that waste paper ash may be used as a cement replacement up to 5% by weight and the particle size is less the 90µm to prevent reduction in workability. Keywords: slump test, Compressive strength, split tensile strength, water absorption test, Waste Paper Sludge Ash Concrete, Workability.

Classification of Engineering Properties of Tropical Boulder in Completely Weathered Granite in Johor, Malaysia

2020 ◽  
Vol 17 (2) ◽  
pp. 1059-1069
Author(s):  
Mohd Firdaus Md Dan ◽  
Edy Tonnizam Mohamad ◽  
Ibrahim Komoo ◽  
Aziman Madun ◽  
Siti Norsalkini Mohd Akip Tan
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Uniaxial Compressive Strength ◽  
Point Load ◽  
Engineering Properties ◽  
Dry Density ◽  
Petrographic Analysis ◽  
Point Load Strength ◽  
Weathered Granite ◽  
Completely Weathered Granite

Engineering properties of tropical weathered granite mass have been widely investigated and classified for engineering purposes. However, the engineering properties of tropical boulder in weathered granite profile is poorly understood and not well classified. This study aims to examine and classify the physico-mechanical properties of granite boulder in completely weathered zone. A total of 34 in-situ boulders were examined from two granite quarries located in Southern Johor, Malaysia. Microstructure-mineralogical alterations were analyzed based on petrographic analysis and scanning electron microscopy (SEM). The mechanical properties were including dry density, porosity, point load strength, uniaxial compressive strength and permeability. Three properties were identified as significant indicators to differentiate between tropical boulder and completely weathered granite when it is evaluated from the soil investigation drilling work namely; texture characteristics, discolourations and degree of weathering. Analysis revealed that the alteration of microstructures and minerals such as feldspar, biotite, and plagioclase from corestone (Grade I/II) to saprolite (Grade IV/V) zone were significantly reduced the dry density, point load strength, uniaxial compressive strength and permeability with 32%, 99.5%, 98.6% and 84.8%, respectively. It has also significantly increased the porosity up to 11.6 times or 1065% from corestone to saprolite. The significant different of physico-mechanical properties of material surrounding boulder due to weathering can be classified and useful in evaluation of geotechnical design and geological engineering applications.

THE EFFECT OF POROSITY ON ENGINEERING PROPERTIES OF VESICULAR AMYGDALOIDAL BASALTS

2021 ◽  
Vol 5 (11) ◽  
Author(s):  
P .S.K.Murthy ◽  
Sachin Gupta ◽  
Dhirendra Kumar ◽  
Mahabir Dixit
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Uniaxial Compressive Strength ◽  
Modulus Of Elasticity ◽  
Poisson’S Ratio ◽  
Central India ◽  
Poisson's Ratio ◽  
Engineering Properties ◽  
Secondary Minerals

The interconnection of vesicles in basaltic flows greatly affects the engineering properties such as uniaxial compressive strength, modulus of elasticity, Poisson’s ratio, tensile strength and sonic velocities. Sometimes these vesicles are filled with secondary minerals such as quartz/olivine/calcite form as amygdules (which are impermeable). In the present study, to understand effect of porosity, vesicular and amygdular basaltic flows collected from central and west-central India were investigated for these engineering properties and correlated with apparent porosity of core samples. It is observed that a good level of correlation is obtained for uniaxial compressive strength (UCS), elastic modulus (E) and Poisson’s ratio in vesicular basalts when porosity >8-10%. In case of Brazilian strengths a linearly downward trend is observed with the increase in porosity values. And, no significant correlation is observed for waves’ velocities in both variants of basalts.

scholarly journals Performance Evaluation of Pre-foamed Ultra-lightweight Composites Incorporating Various Proportions of Slag

2020 ◽  
Author(s):  
Trong-Phuoc Huynh ◽  
Van-Hien Pham ◽  
Ngoc-Duy Do ◽  
Trong-Chuc Nguyen ◽  
Nguyen-Trong Ho
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Water Absorption ◽  
Drying Shrinkage ◽  
Engineering Properties ◽  
Dry Density ◽  
Brick Wall ◽  
River Sand ◽  
Microstructure Observation ◽  
Granulated Blast Furnace Slag

This research examines the feasibility of using a mixture of cement, fly ash, ground granulated blast-furnace slag, and river sand to manufacture pre-foamed ultra-lightweight composite (PULC). Four PULC specimens were prepared with the substitution of cement by slag at 0, 10, 20, and 30 % by weight. The engineering properties of PULC samples were evaluated through the tests of compressive strength, dry density, water absorption, drying shrinkage, and thermal conductivity. Besides, numerical simulation of heat transfer through the PULC brick wall and the microstructure observation were performed. The performance of PULC mixtures incorporating slag showed higher effectiveness than merely used cement. The substitution of 20 % cement by slag resulted in the highest compressive strength as well as the lowest value of water absorption of the PULC samples. Also, the efficiency of the thermal conductivity was in inverse proportion with the density of PULC specimens and it was right for water absorption and drying shrinkage. Moreover, numerical simulations showed that the temperature distribution values in the wall made by PULC material were smaller than in the wall made by the normal clay brick in the same position. Besides, the microstructure analysis revealed that the existence of slag generated a more dense structure of PULC samples with the addition of calcium-silicate-hydrate (C-S-H) gel, especially for a mix containing 20 % slag. Thus, the results of this study further demonstrated that a 20 % slag was the optimal content for the good engineering properties of the PULC samples.

scholarly journals Experimental Study on Improvement of Marine Soft Soil with Alkali Residue

2018 ◽  
Vol 53 ◽  
pp. 04021
Author(s):  
SHAO Yong ◽  
LIU Xiao-li ◽  
ZHU Jin-jun
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Void Ratio ◽  
Soft Soil ◽  
Compressive Modulus ◽  
Engineering Properties ◽  
Test Results ◽  
Use Of Resources ◽  
One Year

Industrial alkali slag is the discharge waste in the process of alkali production. About one million tons of alkali slag is discharged in China in one year. It is a burden on the environment, whether it is directly stacked or discharged into the sea. If we can realize the use of resources, it is a multi-pronged move, so alkali slag is used to improve solidified marine soft soil in this paper. The test results show that the alkali residue can effectively improve the engineering properties of marine soft soil. Among them, the unconfined compressive strength and compressive modulus are increased by about 10 times, and the void ratio and plasticity index can all reach the level of general clay. It shows that alkali slag has the potential to improve marine soft soil and can be popularized in engineering.

scholarly journals Influence of the surface treatment of tire rubber residues added in mortars

2008 ◽  
Vol 1 (2) ◽  
pp. 113-120 ◽  
Author(s):  
A. C. Marques ◽  
J. L. Akasaki ◽  
A. P. M. Trigo ◽  
M. L. Marques
Keyword(s):  
Mechanical Properties ◽  
Aqueous Solution ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Surface Treatment ◽  
Water Absorption ◽  
Modulus Of Elasticity ◽  
Tire Rubber ◽  
Flow Test ◽  
Made In

In this work it was evaluated the influence tire rubber addition in mortars in order to replace part of the sand (12% by volume). It was also intended to verify if the tire rubber treatment with NaOH saturated aqueous solution causes interference on the mechanical properties of the mixture. Compressive strength, splitting tensile strength, water absorption, modulus of elasticity, and flow test were made in specimens of 5cmx10cm and the tests were carried out to 7, 28, 56, 90, and 180 days. The results show reduction on mechanical properties values after addition of tire rubber and decrease of the workability. It was also observed that the tire rubber treatment does not cause any alteration on the results compared to the rubber without treatment.

scholarly journals Effect of Curing Method on Properties of Lightweight Foamed Concrete

2018 ◽  
Vol 7 (2.29) ◽  
pp. 927 ◽  
Author(s):  
Bishir Kado ◽  
Shahrin Mohammad ◽  
Yeong Huei Lee ◽  
Poi Ngian Shek ◽  
Mariyana Aida Ab Kadir
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Water Absorption ◽  
Precast Concrete ◽  
Construction Materials ◽  
Splitting Tensile Strength ◽  
Structural Members ◽  
Lightweight Construction ◽  
Foamed Concrete ◽  
Curing Method

Lightweight construction is aimed to achieve a sustainable feature by reducing transportation frequency and construction materials usage during construction phase. Lightweight precast concrete may serve an alternative for the lightweight construction. There are rarely application can be found for structural members as lightweight panels always to be used for secondary or non-load bearing members. This paper presents an experimental study on properties (compressive strength, splitting tensile strength, water absorption) of lightweight foamed concrete (LFC) at two different curing methods. LFC with densities of 1500, 1700, and 1800 kg/m3, cement-sand ratio of 2:1 and water-cement ratio of 0.5 were investigated. The results showed LFC can be produced with the properties ofdensity range of 1500 to 1800 kg/m3 and corresponding compressive strength of 10 to 39 MPa. The higher the density of LFC, the less the water absorption for all the curing method considered, the highest and the lowest water absorption was 11.3% and 2.0% for 1500 kg/m3 cured in water and 1800 kg/m3 cured in air respectively. Compressive strength of LFC increases with age and density while water cured LFC has high compressive strength. Splitting tensile strength increases with density of LFC, but air cured LFC has more splitting tensile strength than water cured of the same density. The highest splitting tensile strength recorded was 3.92 MPa for 1800 kg/m3 cured in air, which was about 16% of its compressive strength at 28 days of curing age. These properties are important and can be applied to LFC precast structural members with air or water curing method which have less references for LFC in structural usage.  

scholarly journals The Effect of Nano Metakaolin Material on Some Properties of Concrete

2013 ◽  
Vol 6 (1) ◽  
pp. 50-61
Author(s):  
Amer M. Ibrahem ◽  
Shakir A. Al-Mishhadani ◽  
Zeinab H.Naji
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Portland Cement ◽  
Water Absorption ◽  
Thermal Activation ◽  
Ordinary Portland Cement ◽  
Splitting Tensile Strength ◽  
Kaolin Clay ◽  
Cement Ratio ◽  
Water Cement Ratio

This investigation aimed to study the effect of nano metakaolin ( NMK ) on some properties (compressive strength ,splitting tensile strength & water absorption ) of concrete. The nano metakaolin (NMK) was prepared by thermal activation of kaolin clay for 2 hours at 750 Ċ. The cement used in this investigation consists of ordinary Portland cement (OPC). The OPC was partially substituted by NMK of ( 3, 5 & 10%) by weight of cement. The C45 concrete was prepared , using water/cement ratio ( W/c) of (0.53) .The Water absorption was tested at 28 days while the tests (compressive strength ,splitting tensile strength) were tested at ages of (7, 28, 60,& 90) days . The compressive strength and splitting tensile strength of concrete with NMK were higher than that of reference concrete with the same W/c ratio.The improvement in the compressive strength when using NMK was (42.2, 55.8 , 63.1% ) at age 28 days for ( 3%, 5%, &10% ) replacement of NMK respectively whereas the improvement in the splitting tensile strength was (0% , 36% & 46.8 %) at age of 28 days when using (3%, 5%, &10% ) NMK respectively. The improvement in the water absorption was (16.6%, 21.79%, &25.6 ) when using (3, 5, &10% )NMK.

scholarly journals PROPERTIES OF MORTARS CONTAINING TIRE RUBBER WASTE AND EXPANDED POLYSTYRENE (EPS)

2018 ◽  
pp. 219-225 ◽  
Author(s):  
Adriane Pczieczek ◽  
Adilson Schackow ◽  
Carmeane Effting ◽  
Itamar Ribeiro Gomes ◽  
Talita Flores Dias
Keyword(s):  
Compressive Strength ◽  
Specific Gravity ◽  
Water Absorption ◽  
Expanded Polystyrene ◽  
Fine Aggregate ◽  
Tire Rubber ◽  
Air Content ◽  
Rubber Waste ◽  
Hardened State ◽  
Entrained Air

This study aims to evaluate the application of discarded tire rubber waste and Expanded Polystyrene (EPS) in mortar. For mortars fine aggregate was replaced by 10%, 20% and 30% of rubber and, 7.5% and 15% of EPS. We have verified the consistency, density, amount of air and water retentitivity in fresh state. The compressive strength, water absorption, voids ratio and specific gravity have been also tested in hardened state. The application of rubber powder contributed to the increase in entrained air content and in reducing specific gravity, as well as reducing compressive strength at 28 days. The addition of EPS also contributed to the increase of workability, water absorption and voids ratio, and decreased density and compressive strength when compared to the reference mortar. The use of rubber waste and EPS in mortar made the material more lightweight and workable. The mortars mixtures containing 10% rubber and 7.5% EPS showed better results.

Sign in / Sign up

Export Citation Format

Share Document