scholarly journals Pot-In-Pot Production and Cyclic Irrigation Influence Growth and Irrigation Efficiency of ‘Okame’ Cherries

1998 ◽  
Vol 16 (3) ◽  
pp. 159-162 ◽  
Author(s):  
John M. Ruter
Keyword(s):  
Water Loss ◽  
Production System ◽  
Dry Weight ◽  
Stem Diameter ◽  
Total Biomass ◽  
Root:Shoot Ratio ◽  
Irrigation Application ◽  
Application Efficiency ◽  
Shoot Dry Weight ◽  
Daily Water

Abstract A study was conducted with Prunus x incamp ‘Okame’ to evaluate the effects of a pot-in-pot production system (PIP) compared to a conventional above-ground system (CAG) and cyclic irrigation on plant growth and water loss. Plants were grown in #7 (26 liter) containers with a pinebark: sand (8:1 by vol) substrate. Cyclic irrigation provided the same total volume of water, but was applied one, three, or four times per day. Final plant height and stem diameter, shoot and root dry weight, total biomass, and root:shoot ratio all increased for plants grown pot-in-pot compared to above-ground. Multiple irrigation cycles increased stem diameter, shoot dry weight and total biomass compared to a single irrigation application. Multiple irrigation cycles also decreased the root:shoot ratio. Mean daily water loss (plant transpiration + evaporative loss from the substrate) was influenced by production system, irrigation, and date. Mean daily water loss was 30% higher for pot-in-pot grown plants compared to above-ground. Cyclic irrigation resulted in a two-fold decrease in average leachate volume and a 27% increase in overall irrigation application efficiency compared to a single application. Production system had no affect on leachate volume or irrigation application efficiency. Substrate pH increased when cyclic irrigation was used. Production system and irrigation had no affect on soluble salts. Nitrate-N concentrations were less in the leachate of plants grown pot-in-pot compared to above-ground.

scholarly journals Pot-in-pot Production and Cyclic Irrigation Influences Growth and Evapotranspiration of `Okame' Cherry

HortScience ◽  
1997 ◽  
Vol 32 (3) ◽  
pp. 546B-546 ◽  
Author(s):  
John M. Ruter
Keyword(s):  
Plant Growth ◽  
Production System ◽  
Nitrate Nitrogen ◽  
Dry Weight ◽  
Stem Diameter ◽  
Total Biomass ◽  
Soluble Salts ◽  
Root:Shoot Ratio ◽  
Shoot Dry Weight ◽  
Ground System

A study was conducted with Prunus × incamp `Okame' to evaluate the effects of a pot-in-pot production system compared to a conventional above-ground system and cyclic irrigation on plant growth and water loss. Plants were grown in #7 (26-L) containers with a 8:1 pinebark:sand (v/v) substrate. Cyclic irrigation provided the same total volume of water, but was applied one, three, or four times per day. Final plant height and stem diameter, shoot and root dry weight, total biomass, and root:shoot ratio were all increased for plants grown pot-in-pot compared to above-ground. Multiple irrigation cycles increased stem diameter, shoot dry weight, and total biomass, compared to a single irrigation application. Multiple irrigation cycles decreased the root:shoot ratio. Evapotranspiration was influenced by production system, irrigation, and date. Amount of water lost as leachate was influenced by irrigation and date. Cyclic irrigation resulted in a two-fold decrease in leachate volume. Soluble salts and nitrate-nitrogen in the leachate were influenced by an interaction between production system, irrigation, and date.

scholarly journals Effects of Cyclic Micro-irrigation and Substrate in Pot-in-pot Production

1998 ◽  
Vol 16 (4) ◽  
pp. 215-218
Author(s):  
Glenn B. Fain ◽  
Ken M. Tilt ◽  
Charles H. Gilliam ◽  
Harry G. Ponder ◽  
Jeff L. Sibley
Keyword(s):  
Inorganic Nitrogen ◽  
Acer Rubrum ◽  
Dry Weight ◽  
Water Volume ◽  
Total N ◽  
Irrigation Application ◽  
Application Efficiency ◽  
Shoot Dry Weight ◽  
Micro Irrigation ◽  
Large Container

Abstract This study was conducted to evaluate production techniques for increasing irrigation application efficiency [(water volume applied − water volume leached) / water volume applied] for large container trees. Three irrigation treatments (single, three cycle and six cycle) and three substrate treatments [pinebark, pinebark:coir (4:1 by vol), and pinebark:peat (4:1 by vol)] were evaluated for effects on irrigation application efficiency and growth of Acer rubrum ‘Franksred’ in a pot-in-pot production system in Auburn, AL. Substrate pH, electrical conductivity and leachate total inorganic nitrogen (N) content were measured. Cyclic irrigation reduced total N lost by a minimum of 89% when compared to a single irrigation application. Irrigation application efficiency increased with cyclic irrigation compared to a single irrigation application and for the pinebark: coir substrate compared to the pinebark. Growth was greater when irrigation was applied in six cycles than in a single irrigation application. Trees grown in pinebark: peat substrate had greater shoot dry weight than those grown in the pinebark substrate.

scholarly journals Production System and Copper Hydroxide Influences on Growth and Photosynthesis of Magnolia grandiflora `St. Mary'

HortScience ◽  
1995 ◽  
Vol 30 (4) ◽  
pp. 795A-795
Author(s):  
John M. Ruter
Keyword(s):  
Production System ◽  
Dry Weight ◽  
Weight Percent ◽  
Total Biomass ◽  
Copper Hydroxide ◽  
Magnolia Grandiflora ◽  
Root Dry Weight ◽  
Shoot Dry Weight ◽  
Aboveground Production ◽  
Growth Production

A study was conducted with Magnolia grandiflora `St. Mary' to evaluate the effects of a pot-in-pot production system compared to a conventional aboveground production system and containers treated with or without copper hydroxide (Spin Out™). At 4 and 12 months after beginning the study, plants grown pot-in-pot were taller than plants in the conventional system. Stem diameters of plants grown pot-in-pot were also larger at 12 months. Production system influenced root dry weight in the outer 50% of the container, total root dry weight, percent root dry weight in the inner 50% of the container, percent root dry weight in the outer 50% of the container, and total biomass. Production system had no effect on shoot dry weight. Treatment with copper hydroxide had no effect on root or shoot growth. Production system and copper treatment influenced degree of root coverage. Plants grown pot-in-pot had higher rates of Ps and gs with increased Ci levels compared to plants above-ground. Production system had no effect on calculated transpiration rates.

Response of Taxus times media var. densiformis to inoculation with arbuscular mycorrhizal fungi

1998 ◽  
Vol 28 (1) ◽  
pp. 150-153
Author(s):  
J N Gemma ◽  
R E Koske ◽  
E M Roberts ◽  
S Hester
Keyword(s):  
Arbuscular Mycorrhizal Fungi ◽  
Mycorrhizal Fungi ◽  
Glomus Intraradices ◽  
Arbuscular Mycorrhizal ◽  
Dry Weight ◽  
Root Systems ◽  
Stem Diameter ◽  
Rooted Cuttings ◽  
Shoot Dry Weight ◽  
Mycorrhizal Plants

Rooted cuttings of Taxus times media var. densiformis Rehd. were inoculated with the arbuscular mycorrhizal fungi Gigaspora gigantea (Nicol. & Gerd.) Gerd. & Trappe or Glomus intraradices Schenck and Smith and grown for 9-15 months in a greenhouse. At the completion of the experiments, leaves of inoculated plants contained significantly more chlorophyll (1.3-4.1 times as much) than did noninoculated plants. In addition, mycorrhizal plants had root systems that were significantly larger (1.3-1.4 times) and longer (1.7-2.1 times) than nonmycorrhizal plants, and they possessed significantly more branch roots (1.3-2.9 times). No differences in stem diameter and height or shoot dry weight were evident at the end of the experiments, although the number of buds was significantly greater in the cuttings inoculated with G. intraradices after 15 months.

scholarly journals AVOCADO SEEDLINGS MULTIPLE STEMS PRODUCTION

2016 ◽  
Vol 38 (2) ◽  
Author(s):  
MARCUS VINICIUS SANDOVAL PAIXÃO ◽  
JOSÉ CARLOS LOPES ◽  
EDILSON ROMAIS SCHMILDT ◽  
RODRIGO SOBREIRA ALEXANDRE ◽  
CAROLINE MERLO MENEGHELLI
Keyword(s):  
Root Length ◽  
Dry Weight ◽  
Adventitious Rooting ◽  
Dry Mass ◽  
Stem Diameter ◽  
Experimental Unit ◽  
Shoot Height ◽  
Shoot Dry Weight ◽  
Federal Institute ◽  
Multiple Stems

ABSTRACT This study aimed to evaluate the potential of multi-stems in avocado seeds according to their mass as well as the adventitious rooting of multi-stem budding with or without the use of auxin. The research was carried out at the Vegetation House of Federal Institute of Espírito Santo, Campus Santa Teresa -ES, with seeds of different masses: <60 g, 61 to 80 g, 81 to 100 g and >100 g, in which each experimental unit was made of five seeds, distributed within five repetitions, under a completely randomized design. The seeds were put to germinate and the percentage number of emergence and multiple stems were evaluated. After 150 days, the following evaluations were carried out: survival of rooted cuttings; number of leaves; stem diameter; root length; root volume; root and shoot fresh mass; root and shoot dry mass; shoot height; absolute growth and shoot growth rate; shoot dry weight/root dry mass ratio; shoot height/stem diameter ratio; shoot height/root length and Dickson's quality index ratio. Avocado seeds with mass over 100 g and between 81-100 g presented higher percentage of multiple stems. Rods over 20 cm that were not treated with IBA (indole-3-butyric acid) resulted on avocado plants of better quality. The use of IBA (2000 mg L-1) does not affect the rooting and growth of avocado's multi-stem plants.

scholarly journals Evaluation of a Substrate-applied Humectant to Mitigate Drought Stress in Young, Container-grown Plants

2015 ◽  
Vol 33 (3) ◽  
pp. 137-141
Author(s):  
Bruce R. Roberts ◽  
Chris Wolverton ◽  
Samantha West
Keyword(s):  
Drought Stress ◽  
Root Growth ◽  
Shoot Growth ◽  
Dry Weight ◽  
Root:Shoot Ratio ◽  
Xylem Water Potential ◽  
Bedding Plants ◽  
Shoot Dry Weight ◽  
Soilless Substrate ◽  
Absorbing Roots

The efficacy of treating soilless substrate with a commercial humectant was tested as a means of suppressing drought stress in 4-week-old container-grown Zinnia elegans Jacq. ‘Thumbelina’. The humectant was applied as a substrate amendment at concentrations of 0.0, 0.8, 1.6 and 3.2% by volume prior to withholding irrigation. An untreated, well-watered control was also included. The substrate of treated plants was allowed to dry until the foliage wilted, at which time the plants were harvested and the following measurements taken: number of days to wilt (DTW), xylem water potential (ψx), shoot growth (shoot dry weight, leaf area) and root growth (length, diameter, surface area, volume, dry weight). For drought-stressed plants grown in humectant-treated substrate at concentrations of 1.6 and 3.2%, DTW increased 25 and 33%, respectively. A linear decrease in ψx was observed as the concentration of humectant increased from 0.0 to 3.2%. Linear trends were also noted for both volumetric moisture content (positive) and evapotranspiration (negative) as the concentration of humectant increased. For non-irrigated, untreated plants, stress inhibited shoot growth more than root growth, resulting in a lower root:shoot ratio. For non-irrigated, humectant-treated plants, the length of fine, water-absorbing roots increased linearly as humectant concentration increased from 0.0 to 3.2%. Using humectant-amended substrates may be a management option for mitigating the symptoms of drought stress during the production of container-grown bedding plants such as Z. elegans.

Growth and Development of Bigroot Morningglory (Ipomoea pandurata)

1991 ◽  
Vol 5 (4) ◽  
pp. 805-810 ◽  
Author(s):  
Michael J. Horak ◽  
Loyd M. Wax
Keyword(s):  
Root Growth ◽  
Growth And Development ◽  
Dry Weight ◽  
First Year ◽  
Growing Degree Days ◽  
Degree Days ◽  
Root:Shoot Ratio ◽  
Shoot Dry Weight ◽  
Second Year ◽  
Final Harvest

Growth and development of bigroot morningglory was observed and quantified. Emergence occurred 75 ± 5 growing degree days (GDD) after seeding. Flower and seed production began 630 ± 20 GDD after emergence and continued until the first frost killed the shoots. Seedlings needed approximately 460 GDD of growth to become perennial. In the second year of growth, plants emerged in early May and flowered within 425 ± 50 GDD. Shoot dry weight accumulation in first-year plants was 3.5 g for the first 600 GDD after which a fifteenfold increase in dry weight occurred. Root growth followed the same pattern, however the large increase in dry weight occurred approximately 300 GDD later than that of the shoots. The root:shoot ratio was 0.2 to 0.3 for the first 900 GDD and increased to greater than 1.0 by the final harvest.

scholarly journals Optimal LED Wavelength Composition for the Production of High-Quality Watermelon and Interspecific Squash Seedlings Used for Grafting

Agronomy ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 870 ◽  
Author(s):  
Filippos Bantis ◽  
Athanasios Koukounaras ◽  
Anastasios S. Siomos ◽  
Kalliopi Radoglou ◽  
Christodoulos Dangitsis
Keyword(s):  
Blue Emission ◽  
Dry Weight ◽  
Photosynthetic Photon Flux Density ◽  
Stem Diameter ◽  
Photon Flux ◽  
Photon Flux Density ◽  
Light Sources ◽  
High Quality ◽  
Light Emitting ◽  
Shoot Dry Weight

Watermelon is cultivated worldwide and is mainly grafted onto interspecific squash rootstocks. Light-emitting diodes (LEDs) can be implemented as light sources during indoor production of both species and their spectral quality is of great importance. The objective of the present study was to determine the optimal emission of LEDs with wide wavelength for the production of watermelon and interspecific squash seedlings in a growth chamber. Conditions were set at 22/20 °C temperature (day/night), 16 h photoperiod, and 85 ± 5 μmol m−2 s−1 photosynthetic photon flux density. Illumination was provided by fluorescent (FL, T0) lamps or four LEDs (T1, T2, T3, and T4) emitting varying wide spectra. Watermelon seedlings had greater shoot length, stem diameter, cotyledon area, shoot dry weight-to-length (DW/L) ratio, and Dickson’s quality index (DQI) under T1 and T3, while leaf area and shoot dry weight (DW) had higher values under T1. Interspecific squash seedlings had greater stem diameter, and shoot and root DW under T1 and T3, while leaf and cotyledon areas were favored under T1. In both species, T0 showed inferior development. It could be concluded that a light source with high red emission, relatively low blue emission, and a red:far-red ratio of about 3 units seems ideal for the production of high-quality watermelon (scion) and interspecific squash (rootstock) seedlings.

Natural variation in common bean (Phaseolus vulgaris L.) for root traitsand biomass partitioning under drought

2016 ◽  
Vol 50 (6) ◽  
Author(s):  
Parvaze A. Sofi ◽  
Iram Saba
Keyword(s):  
Common Bean ◽  
Root Traits ◽  
Dry Weight ◽  
Biomass Partitioning ◽  
Rooting Depth ◽  
Leaf Biomass ◽  
Root Weight ◽  
Total Biomass ◽  
Phaseolus Vulgaris L ◽  
Shoot Dry Weight

The present study was undertaken to assess the response of common bean under drought in respect of root traits and biomass partitioning in fifteen common bean genotypes. The basal root whorl number and the number of basal roots was highest in case of WB-185 and lowest in case of SR-1, whereas, the basal root growth angle was highest in case of WB-258 and lowest in case of WB-249. Rooting depth measured as the length of longest root harvested was highest in case of WB-6 (66.2) while as lowest value was recorded for WB-112 (20.4). Dry root weight was highest in case of WB-216 (0.45) and lowest value was recorded for WB-341 (0.22). Similarly leaf biomass was highest in case of WB-6 (0.58) followed by WB-216 (0.58) and the lowest value recorded for WB-1186 (0.12). Shoot dry weight was highest for WB-6 (0.55) followed by WB-216 (0.44) and the lowest value recorded for WB-1186 (0.118). Pod dry weight was highest for WB-489 (2.28) followed by WB-216 (2.19) and the lowest value recorded for WB-83 (0.68).489. Root biomass proportion was highest for WB-195 (18.34) and lowest for WB-489 (10.00). Similarly leaf biomass to total biomass was highest in case of WB-83 (23.19) whereas lowest value was recorded for WB-1186 (7.60). Highest stem biomass proportion was recorded for Arka Anoop (19.19) and the lowest value was recorded for WB-1186 (7.591). Biomass allocation to pods was highest in case of WB-489 (69.92) followed by WB-1186 (68.69) whereas lowest value was recorded for WB-83 (45.40).

scholarly journals Comparing Effects of Container Treatments on Nursery Production and Field Establishment of Trees with Different Root Systems

2000 ◽  
Vol 18 (2) ◽  
pp. 83-88
Author(s):  
Ursula K. Schuch ◽  
Dennis R. Pittenger ◽  
Philip A. Barker
Keyword(s):  
Biomass Production ◽  
Shoot Growth ◽  
Dry Weight ◽  
Copper Coating ◽  
Total Biomass ◽  
Shoot Dry Weight ◽  
Nursery Production ◽  
Brazilian Pepper ◽  
Container Shape

Abstract The objectives of this study were to determine the effects of container volume, container shape, and copper-coating containers on root and shoot growth during nursery production and after establishment in the field. Liners of ficus (Ficus retusa L. ‘Nitida’), a fibrous-rooted species, and Brazilian pepper (Schinus terebinthifolius Raddi.), a coarse-rooted species, were grown in regular or tall #1 containers in a glasshouse and were subsequently transplanted to the field or into #3 or #5 regular or tall containers. During the nursery phase, copper-coated containers improved rootball quality of ficus and pepper, but biomass production was not affected consistenly by copper coating. Tall, narrow versus regular containers restricted pepper growth throughout the nursery phase and field establishment, but had little effect on ficus. Biomass production of pepper trees was greatest in regular-shaped containers, and tall containers reduced growth consistently. Container shape did not affect shoot growth of ficus. The larger container volume of the #5 yielded greater total biomass of pepper and root dry weight of ficus during nursery production than did #3 pots. In the field, shoot dry weight of ficus was greatest when previously grown in #5 containers, and total biomass of pepper was greatest in both regular #3 or #5 containers.

Sign in / Sign up

Export Citation Format

Share Document