scholarly journals Efficiency of different instruments used for composite filling polishing.

2021 ◽  
Vol 4 (1) ◽  
pp. 31-37
Author(s):  
Andrea-Csinszka Kovacs-Ivacson ◽  
Alexandra Mihaela Stoica ◽  
Mónika Kovacs ◽  
Mihai Pop
Keyword(s):  
Surface Roughness ◽  
Control Group ◽  
Mean Values ◽  
Significance Level ◽  
Caries Treatment ◽  
Before And After ◽  
Long Time ◽  
Surface Irregularities ◽  
Surface Staining

Abstract Introduction: Improper finishing and polishing of fillings leads to surface roughness of the restoration which leads to excessive plaque accumulation, gingival irritation, increased surface staining and poor aesthetics of restored teeth. Therefore, it is essential to use polishing instruments and pastes as a final step of simple caries treatment in order to achieve optimal long-time results. The aim of this study is to evaluate the efficiency of 4 different finishing and polishing instruments used for surface smoothening of aesthetic restorative materials in vitro. Materials and methods: 40 composite (Reality X) samples were prepared in vitro. Their surface irregularities were measured along 3 diagonals before and after polishing. Sof-Lex discs (3M Espe), rubber cones (Kenda), Arkansas stone (Fino) and polishing paste and a professional toothbrush (Kerr) were used for polishing. Each sample was polished under 5N pressure for 30 seconds at 3000 rpm. The surface roughness was than measured using a profilometer. Statistic analysis was performed using ANOVA and unpaired T-tests, the significance level was set at a value of p<0.05. Results: Based on the mean values, the smallest roughness was found in the control group- 0.11, while the highest in the rubber polishers and Arkansas stone group- 0.47 and 0.48. The values for the Sof-Lex disc group and the polishing paste-toothbrush group were 0.40 and 0.39. Statistical analysis showed no significant differences between the four groups. Conclusion: It is mandatory to use polishing tools in order to obtain a smooth surface of the restoration and avoid the unwanted long-term complications. Polishing using brush and abrasive paste produced the smoothest surface of the composite.

scholarly journals Effect of whitening dentifrices on the surface roughness of a nanohybrid composite resin

2016 ◽  
Vol 10 (02) ◽  
pp. 170-175 ◽  
Author(s):  
Gabriela Migliorin da Rosa ◽  
Luciana Mendonça da Silva ◽  
Márcio de Menezes ◽  
Hugo Felipe do Vale ◽  
Diego Ferreira Regalado ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Composite Resin ◽  
Wilcoxon Test ◽  
Control Group ◽  
Mean Values ◽  
Short Period ◽  
Significant Difference ◽  
Before And After ◽  
Nanohybrid Composite ◽  
One Way Anova

ABSTRACT Objectives: The present study verified the influence of whitening dentifrices on the surface roughness of a nanohybrid composite resin. Materials and Methods: Thirty-two specimens were prepared with Filtek™ Z350 XT (3M/ESPE) and randomly divided into four groups (n = 08) that were subjected to brushing simulation equivalent to the period of 1 month. The groups assessed were a control group with distilled water (G1), Colgate Total 12 Professional Clean (G2), Sensodyne Extra Whitener Extra Fresh (G3), and Colgate Luminous White (G4). A sequence of 90 cycles was performed for all the samples. The initial roughness of each group was analyzed by the Surface Roughness Tester (TR 200-TIME Group Inc., CA, USA). After the brushing period, the final roughness was measured, and the results were statistically analyzed using nonparametric Kruskal–Wallis and Dunn tests for intergroup roughness comparison in the time factor. For intragroup and “Δ Final − Initial” comparisons, the Wilcoxon test and (one-way) ANOVA were, respectively, performed (α = 0.05). Results: The roughness mean values before and after brushing showed no statistically significant difference when the different dentifrices were used. None of the dentifrices analyzed increased significantly the nanohybrid composite resin surface roughness in a 1 month of tooth brushing simulation. Conclusions: These results suggest that no hazardous effect on the roughness of nanohybrid composite resin can be expected when whitening dentifrices are used for a short period. Similar studies should be conducted to analyze other esthetic composite materials.

scholarly journals Analysis of Surface Roughness and 3D Scanning Topography of Zirconia Implants Before and After Photofunctionalisation by 3D Optical Profilometry- An Invitro Study

2021 ◽  
Author(s):  
Arunjaikumar Ravindran ◽  
Suma Karthigeyan ◽  
Ramesh Bhat ◽  
Madhulika Naidu ◽  
Senthilnathan Natarajan ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Roughness Parameter ◽  
In Vitro Study ◽  
Control Group ◽  
P Value ◽  
Study Group ◽  
Optical Profilometry ◽  
Before And After ◽  
Zirconia Implants

Introduction: Zirconia is considered as an alternative material for the fabrication of implants. Surface roughness of the implant plays a fundamental role in the initial bone formation. The rationale of using 3D optical profilometry in this study was to evaluate the surface roughness of the zirconia implants before and after Ultraviolet (UV) photofunctionalisation. Also, Moreso 3D optical instruments have a better resolution than the mechanical ones like Atomic Force Microscopy (AFM). Aim: To analyse the surface roughness and topography of zirconia implants after photofunctionalisation using optical profilometry. Materials and Methods: This is an in-vitro study conducted over a period of six months from March 2020 to August 2020. Ten commercially machined Zirconia implants, five each in study and control group, were micro analysed at three different regions (abutment, thread and crest) by optical profilometry. Study group was surface treated by UV radiation for 48 hours. Quantitative morphometric analysis was done between two groups and p-value less than 0.05 was considered statistically significant. The statistical test applied in this study was independent t-test. Results: Scanning micrographs of the study group revealed highest density of summits contributing to increased surface area in the study group. Quantitative analysis of surface roughness showed statistically significant higher mean roughness parameter for photofunctionalised implants in abutment, crest and thread region (p<0.05). Conclusion: Photofunctionalisation is a potentially synergistic technique in producing textured zirconia implants.

scholarly journals Comparative in vitro study of root roughness after instrumentation with ultrasonic and diamond tip sonic scaler

2006 ◽  
Vol 14 (2) ◽  
pp. 124-129 ◽  
Author(s):  
Fernanda Vieira Ribeiro ◽  
Renato Correa Viana Casarin ◽  
Francisco Humberto Nociti Júnior ◽  
Enilson Antônio Sallum ◽  
Antonio Wilson Sallum ◽  
...  
Keyword(s):  
Surface Roughness ◽  
In Vitro Study ◽  
Root Surface ◽  
Control Group ◽  
Human Teeth ◽  
Treatment Groups ◽  
Before And After ◽  
Root Surfaces ◽  
Scanning Electron

OBJECTIVE: The purpose of this study was to evaluate the root surface roughness after instrumentation with hand curette and diamond-coated sonic and universal ultrasonic tips. MATERIALS AND METHODS: Forty root surfaces of human teeth were randomly assigned to four treatment groups: control group (without instrumentation), curette instrumentation, ultrasonic instrumentation with universal tip and sonic instrumentation with diamond-coated tip. Each sample was instrumented with fifteen strokes. Before and after instrumentation, surface roughness was measured. In addition, the root surface topography was examined after treatment under the scanning electron microscope. RESULTS: Significant statistical differences (p <0.05) were observed when comparing the control group (0.48±0.07mm) to the treated groups (hand - 1.246±0.279mm, ultrasonic - 1.468±0.177mm and sonic instrumentation - 1.576±0.20mm). The highest roughness was produced by diamond-coated sonic tip and by ultrasonic universal tip (p >0.05). CONCLUSION: The diamond-coated tip with sonic scaler instrumentation and ultrasonic instrumentation produce similar root surface roughness, higher than curette instrumentation.

scholarly journals A Novel Polishing Paste (Mollusk Shells) for Poly (Methylmethacrylate)

2021 ◽  
Vol 2021 ◽  
pp. 1-6
Author(s):  
Nicole Guerra ◽  
Evelin Meneses ◽  
Stefany Caballero-García ◽  
Frank Mayta-Tovalino
Keyword(s):  
Surface Roughness ◽  
Acrylic Resin ◽  
Wilcoxon Test ◽  
Stone Surface ◽  
Pumice Stone ◽  
Mean Values ◽  
Significance Level ◽  
Mollusk Shells ◽  
Paired Wilcoxon Test

Objective. The aim of this study was to evaluate the effectiveness of a mollusk shells polishing paste (Donax obesulus) on the surface roughness of acrylic resin poly (methylmethacrylate) (PMMA). Methods. This study was an in vitro experimental design. A sample size of 72 was divided into 4 groups of n = 18 each. PMMA specimens were prepared and polished with the evaluated pastes using mollusk shells (experimental paste) and pumice stone. Surface roughness (μm) was measured using a profilometer after polishing the PMMA samples. The paired Wilcoxon test was used to evaluate the roughness values at 24 and 48 hours. Then, the Mann–Whitney U test was used to identify the differences between the effects of the two groups evaluated with a significance level of α = 0.05. Results. The roughness difference between the pastes under study was compared, and mean values of 0.50 ± 0.07 μm (mollusk shell paste group) and 0.45 ± 0.12 μm (pumice group) were obtained. No statistically significant differences were found between the experimental paste and pumice stone paste p = 0.309 . The specimens polished with pumice stone paste showed higher roughness values, while those polished with the experimental paste exhibited the lowest values. Conclusion. In summary, mollusk shells polishing paste had a decrease in roughness values compared to pumice, although these differences were not statistically significant.

The Effect of Different Finishing and Polishing Systems on the Surface Roughness of Different Composite Restorative Materials

2007 ◽  
Vol 8 (2) ◽  
pp. 89-96 ◽  
Author(s):  
Hacer Deniz Arisu ◽  
Mine Betül Üçtaşli ◽  
Hüma Ömürlü ◽  
Evrim Eligüzeloğlu ◽  
Suat Özcan ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Composite Resin ◽  
Restorative Material ◽  
Average Surface Roughness ◽  
Significance Level ◽  
Average Surface ◽  
Different Types ◽  
Restorative Materials ◽  
Before And After

Abstract Aim The purpose of this in vitro study was to examine the effect of two different finishing systems on the surface roughness of different types of composite restorative materials. Methods and Materials Thirty specimens, 8 mm in diameter and 3 mm in depth, were prepared using a microfill composite (Clearfil ST, Kuraray Co. Ltd., Osaka, Japan), a hybrid composite (Clearfil AP-X, Kuraray Co. Ltd., Osaka, Japan), and a packable composite (Clearfil Photo Posterior, Kuraray Co. Ltd., Osaka, Japan) cured against a Mylar matrix strip to create a baseline surface. The average surface roughness was measured using a surface profilometer (Surftest 211, Mitutoyo, Japan) in five different positions on each sample before and after finishing with one of the two finishing systems [Sof-Lex discs (3M) and Po-Go (Dentsply)]. The obtained data were analyzed by two-way analysis of variance (ANOVA) at a p=0.05 significance level. Results There were statistically significant differences in the average surface roughness (Ra, ìm) between the Mylar matrix strip, Sof-Lex discs, and Po-Go discs (p<0.05). For all tested materials, the Mylar matrix strip provided smoother surfaces than both of the finishing systems (p<0.05). When the finishing discs were compared, Sof-Lex discs produced a smoother surface than Po-Go discs for all tested materials (p<0.05). Conclusion The Mylar matrix strip provided a smoother surface than Sof-Lex and Po-Go discs. Furthermore, Sof-Lex discs produced smoother surfaces than Po-Go discs. Sof-Lex and Po-Go systems produced clinically acceptable surface roughness for microfill, hybrid, and packable composite resin materials. The effect of finishing and polishing systems on surface roughness was dependent on both the system and the composite resin restorative material. Citation Üçtaşli MB, Arisu HD, Ömürlü H, Eligüzeloğlu E, Özcan S, Ergun G. The Effect of Different Finishing and Polishing Systems on the Surface Roughness of Different Composite Restorative Materials. J Contemp Dent Pract 2007 February;(8)2:089-096.

Comparative Study to Evaluate the Surface Detail Reproduction of Dental Stone after Immersion in Various Different Disinfectant Solutions, Under Stereomicroscope 10 X Magnification –An In-Vitro Study

2017 ◽  
Vol 9 (3) ◽  
Author(s):  
Rathika Rai ◽  
M. A. Easwaran ◽  
K. T. Dhivya
Keyword(s):  
Sodium Hypochlorite ◽  
In Vitro Study ◽  
Control Group ◽  
Immersion Method ◽  
Significant Difference ◽  
Surface Irregularities ◽  
Disinfectant Solution ◽  
Surface Detail ◽  
Group B

Aim: To evaluate the surface detail reproduction of dental stone this is immersed in different disinfectant solution and studied under stereomicroscope. Methodology: Total number of 30 specimens of dental stone (Type III) were made with measurements of 1.5cm diameter and 1cm height .This samples are divided in to 3 groups group A,B,C. were A is immersed in Distilled water which was taken as control group ;B is immersed in 2% Glutaraldehyde and C is immersed in 5%sodium hypochlorite. Each specimen were immersed in the disinfectant solution for 15 minutes and dried under room temperature for 24 hrs. After 24 hrs each specimens are studied under stereomicroscope for surface details. Result: The results showed no significant difference in the surface irregularities and porosities for a group 1 and group 2 except group 3 which showed significant increase in the porosities, surface irregularities and erosions after disinfection with 5% NaHOCl by immersion method. Conclusion: The surface detail reproduction capacity of die stone was adversely affected when 5% Sodium hypochlorite was used as disinfectant solution when compare d to control group and 2% Glutaraldehyde

Sensitivity of bioelectrical impedance to detect changes in human body composition

1989 ◽  
Vol 67 (4) ◽  
pp. 1643-1648 ◽  
Author(s):  
R. Ross ◽  
L. Leger ◽  
P. Martin ◽  
R. Roy
Keyword(s):  
Body Composition ◽  
Human Body ◽  
Correlation Coefficients ◽  
Bioelectrical Impedance ◽  
Mean Values ◽  
Significance Level ◽  
Exercise Regimen ◽  
Before And After ◽  
Hydrostatic Weighing ◽  
Human Body Composition

The purpose of this study was to compare the estimates of lean body mass (LBM) and percent body fat (%BF), as predicted by bioelectrical impedance (BIA) and sum of skinfolds (SF), with those derived by hydrostatic weighing (HW) obtained before and after a 10-wk diet and exercise regimen. The experimental (E) group consisted of 17 healthy male subjects; 20 healthy males served as the control (C) group. Post hoc Scheffe contrasts computed on E group data indicated that, for both LBM and %BF, the Lukaski and Segal BIA equations, as well as the Durnin SF equation, derived mean values that were not significantly different (0.05 significance level) from HW in both pre- and postregimen conditions. For LBM, the same equations derived the following significant (P less than 0.01) correlation coefficients for both pre- and postregimen data: Lukaski, 0.87 and 0.85; Segal, 0.89 and 0.87; and Durnin, 0.90 and 0.88. For %BF, the correlation coefficients were slightly lower but remained statistically significant (P less than 0.01). The findings of this study suggest that the BIA method, by use of either the Lukaski or Segal prediction equations, is a valid means of predicting changes in human body composition as measured by the Siri transformation of body density.

scholarly journals Preliminary In Vitro Wear Assessment of Ceramic Cemented Femoral Components Coupled with Polyethylene Menisci

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2112
Author(s):  
Saverio Affatato ◽  
Paolo Erani ◽  
Maurizio Fersini ◽  
Vincenzo Contaldi ◽  
Anna Rita Terrizzi ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Wear Resistance ◽  
Monoclinic Phase ◽  
Calf Serum ◽  
Wear Test ◽  
Clinical Test ◽  
Preliminary Evaluation ◽  
Before And After ◽  
Roughness Measurements

Success of total knee replacement (TKR) depends on the prosthetic design and materials. The use of metal components is well established with the disadvantage of allergic reactions. Ceramics have been recently proposed because of high wear resistance, excellent biocompatibility, wettability, and suitable mechanical properties. This study was aimed at investigating in vitro wear resistance of Zirconia Toughened Alumina (ZTA)/Ultra-high-molecular-weight polyethylene (UHMWPE) of TKR femoral components. An in vitro protocol was designed with the application of relevant load profile, 6-degrees-of-freedom knee simulator, and 8 × 105 cycles on the ZTA/UHMWPE configuration under bovine calf serum. Before and after wear test, the femoral components were investigated by using the Scanning Electron Microscope (SEM) and the X-Ray Diffraction (XRD) analyses, and stylus surface roughness measurements. The proposed pre-clinical test yielded repeatable results. In particular, gravimetric results showed that, after 8 × 105 cycles, the mean weight loss of the polyethylene mobile components is 5.3 ± 1.1 mg. The surface roughness measurements (Ramax) performed after the wear test showed no significant variation on the UHMWPE menisci. A slight increase of roughness has been found on the ZTA (0.02 µm before wear test, 0.28 µm after the test). SEM observations did not show significant modification of the surface morphology. Tetragonal to monoclinic phase ratio was measured by XRD before and after wear test to evaluate stability of tetragonal ZrO2 phase. Minimal conversion of tetragonal to monoclinic phase was found from 5.4 to 8%. Although this study is a preliminary evaluation limited to in vitro tests, it provides novel pre-clinical indications about the potential of ceramic TKR femoral components.

scholarly journals In vitro activity of zinc oxide-eugenol and glass ionomer cements on Candida albicans

2005 ◽  
Vol 19 (2) ◽  
pp. 134-138 ◽  
Author(s):  
Anna Carolina Aguiar Cassanho ◽  
Aletéia Massula Fernandes ◽  
Luciane Dias de Oliveira ◽  
Claudio Antonio Talge Carvalho ◽  
Antonio Olavo Cardoso Jorge ◽  
...  
Keyword(s):  
Zinc Oxide ◽  
Candida Albicans ◽  
Control Group ◽  
Glass Ionomer ◽  
Experimental Conditions ◽  
Mean Values ◽  
Zinc Oxide Eugenol ◽  
Colony Forming Units ◽  
And Control

The aim of this study was to evaluate in vitro the antimicrobial activity of glass ionomer (GIC) and zinc oxide-eugenol (ZOE) cements against Candida albicans. Standardized GIC and ZOE specimens were maintained in contact with C. albicans suspension (1 <FONT FACE=Symbol>´</FONT> 10(6) cells/ml) at 37°C for 24 h, 48 h or 7 days. A control group without any testing cement was included. After the incubation period, aliquots of 0.1 ml were plated on Sabouraud's agar, and then the number of colonies was counted. The results were expressed as values of logarithms of colony-forming units per milliliter (log CFU/mL) and were analyzed statistically by Kruskal-Wallis ANOVA. After 48 h of incubation, the ZOE group presented no growth of C. albicans. GIC and control groups presented similar mean values at all tested periods. According to the results obtained, it could be concluded that, under the experimental conditions, ZOE cement was more effective in vitro against C. albicans than GIC.

scholarly journals FLUORIDE ABSORBED ON EXTRACTED TEETH AFTER IMMERSING IN FLUORIDE TABLET, FLUOCOL SOLUTION AND FLUORIDE DENTRIFICE (IN VITRO TEST)

2016 ◽  
Vol 3 (1) ◽  
pp. 42
Author(s):  
Diyah Fatmasari ◽  
Lanny Sunarjo
Keyword(s):  
Research Result ◽  
Fluoride Concentration ◽  
Group Iv ◽  
In Vitro Test ◽  
Significance Level ◽  
Group Iii ◽  
Group I ◽  
Before And After ◽  
Vitro Test

Background: The role of fluoride in preventing tooth decay both for children and adult has been acknowledged internationally. There are several types of fluoride modalities either topically or systemic way. In Indonesia the modalities used to apply are fluoride tablet, fluocol solution and fluoride containing toothpaste. The purpose of this research is to find the effectiveness of fluoride modalities.Method: The study design was quasy experimental with 40 extracted teeth (Premolar teeth). The teeth divided into four groups D group I soaked on tablet fluor, Group II ; soaked on fluocol solution, Group III soaked on fluoride tooth paste and group IV soaked on Mill J (Aquadest/ Control solution). Fluoride concentration before and after soaking was determined using Spectrophotometer UV-Vis. Fluoride absorption was determined by the reduction of fluoride concentration after soaking.Result: Research result shown that the highest fluoride absorption was on soaking in fluoride tablet, followed by soaking on fluocol and tooth paste (mean fluoride absorption was 0,32; 0,08 and 0,04 ppm). Anova test shown significance level was 0,000.Conclusion: there were a significance of fluoride absorption on soaking in tablet fluoride, fluocol solution and toothpaste. The mechanism of fluoride regimens shown different fluoride absorption.

Sign in / Sign up

Export Citation Format

Share Document