scholarly journals Refinment of a decontamination technology for radioactively contaminated equipment

2021 ◽  
Vol 14 (1) ◽  
pp. 28-38
Author(s):  
V. V. Shelenkova ◽  
◽  
T. A. Kulagina ◽  
Keyword(s):  
Stainless Steel ◽  
Alkaline Solution ◽  
Treatment Time ◽  
Numerical Data ◽  
Chemical Decontamination ◽  
The One ◽  
Decontamination Solution

This article analyzes the data on chemical decontamination methods dealing with radioactively contaminated surfaces. It considers the composition of solutions most commonly used for decontamination purposes. Numerical data are presented to illustrate the effectiveness of various decontamination methods. The paper considers an experiment on the decontamination of stainless steel samples with water following a cavitation treatment. The study reveals a dependence between the decontamination efficiency and the treatment time of the contaminated surface with a decontamination solution based on cavitation-activated water, which appears to be comparable with the results of the one involving an alkaline solution.

Preparation of Electron Transparent Metal-Matrix Composites

1968 ◽  
Vol 26 ◽  
pp. 334-335 ◽  
Author(s):  
M. R. Pinnel ◽  
A. Lawley
Keyword(s):  
Stainless Steel ◽  
Load Transfer ◽  
Volume Fraction ◽  
Steel Wire ◽  
Initial Step ◽  
Interfacial Region ◽  
Matrix Composites ◽  
Specific Test ◽  
The Matrix ◽  
The One

Numerous phenomenological descriptions of the mechanical behavior of composite materials have been developed. There is now an urgent need to study and interpret deformation behavior, load transfer, and strain distribution, in terms of micromechanisms at the atomic level. One approach is to characterize dislocation substructure resulting from specific test conditions by the various techniques of transmission electron microscopy. The present paper describes a technique for the preparation of electron transparent composites of aluminum-stainless steel, such that examination of the matrix-fiber (wire), or interfacial region is possible. Dislocation substructures are currently under examination following tensile, compressive, and creep loading. The technique complements and extends the one other study in this area by Hancock.The composite examined was hot-pressed (argon atmosphere) 99.99% aluminum reinforced with 15% volume fraction stainless steel wire (0.006″ dia.).Foils were prepared so that the stainless steel wires run longitudinally in the plane of the specimen i.e. the electron beam is perpendicular to the axes of the wires. The initial step involves cutting slices ∼0.040″ in thickness on a diamond slitting wheel.

EFFECT OF BORATES AND SILICATES ON WEARING PROPERTIES OF MAO COATINGS

2016 ◽  
Vol 24 (05) ◽  
pp. 1750061
Author(s):  
Yu ZHANG ◽  
YAN-WEI ZHAO ◽  
NAN XIANG ◽  
REN-GUO SONG
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Treatment Time ◽  
Microarc Oxidation ◽  
Smooth Structure ◽  
Electrolytic Bath ◽  
Optimum Treatment ◽  
The One ◽  
Wear Tests

In the present study, microarc oxidation (MAO) coatings were formed on ZL101A aluminum alloy in an electrolytic bath containing 3[Formula: see text]g/L KOH [Formula: see text] 2[Formula: see text]g/L Na2WO[Formula: see text] 4[Formula: see text]g/L KF. The morphology and wearing behavior were investigated. In both electrolytes, the additives were borates (Na2B4O718[Formula: see text]g/L) and silicates (Na2SiO3 18[Formula: see text]g/L), respectively. It was found that the coating formed in borates-containing electrolyte was of compact and smooth structure than that of the one formed in silicates-containing electrolyte at the optimum treatment time. It was found that all the coatings were composed of á-Al2O3 and ã-Al2O3. The microhardness and wear tests proved that the coating formed in borates-containing electrolyte was having better mechanical properties than those of the coating formed in silicates-containing electrolyte.

Table II : Quantitative determination of carbonyl compounds at different odour sources (concentrations in ppb) Rendering plant Gelatine plant neighbourhood neighbourhood Formaldehyde 40 16 Acetaldehyde 39 24 Acetone 36 73 Prcpanal 10 -Isobutyraldehyde 10 30 Pentanal 15 19 Hexanal 3.52 Heptanal 12.5 Octanal 10.5 Nonanal 1 2 acids (figure 7). However extractions always involve a serious decrease in sensitivity, while evaporation of the extract produces a solution in 0.1-0.5 ml of solvent, and only 1 pi of it can be brought in the gas chromatograph. Therefore work is in progress to enhance sensitivity by converting acids in­ to halogenated derivatives, which can be GC-analysed with the more sensitive electron-capture detector. For thiols a similar procedure is investigated as with aldehydes. One possibility is absorption of thiols in an alkaline solution and reaction with 2,4-dinitrochlorobenzene, yielding 2,4-dinitrofenylsulfides, which are analysed by HPLC (9). Sane improvements on removal of reagents at the one hand and on separation of sane by-products on the other hand have to be achieved in order to in­ crease the sensitivity with another factor of ten. 5. CONCLUSION The actual scope and limitations of chemical analysis of odour show that all problems can be tackled as far as emission is concerned. For iititiission measurements seme progress is necessary, but there is no essential reason why chemical analysis would be unable to attain the desired sensitivity for all types of odorants. There is no doubt that in a few years the last dif­ ficulties will be solved. In order to achieve real control of odour nui­ sance, automatic measurement is necessary on a long time basis. There again seme technical development is to be expected. Does this mean that machines are going to decide if an odour is pre­ sent or not? By no means, while the population will always be the reference, and psychophysical measurements will be necessary to make chemical analysis possible.

1986 ◽  
pp. 171-171
Keyword(s):  
Chemical Analysis ◽  
Quantitative Determination ◽  
Alkaline Solution ◽  
Automatic Measurement ◽  
The Other ◽  
Long Time ◽  
Time Basis ◽  
The One ◽  
By Products

scholarly journals THE RELIGIOUS STRUCTURAL EVOLUTION OF THE APUSENI MOUNTAINS

2020 ◽  
Vol 22 (2) ◽  
pp. 107-120
Author(s):  
Mădălin-Sebastian LUNG ◽  
◽  
Gabriela-Alina MUREȘAN ◽  
Keyword(s):  
Statistical Data ◽  
Structural Evolution ◽  
Geographic Location ◽  
Numerical Data ◽  
The Political ◽  
Distinct Population ◽  
Gis Technology ◽  
Microsoft Excel ◽  
Apuseni Mountains ◽  
The One

This paper aims to analyse the religious structure and its evolution in the Apuseni Mountains (Romania). Thusly, we employed statistical data from three distinct population censuses, the first one being the Austro-Hungarian census of 1880. The next one was the one in 1930, organised by Romanian authorities. Furthermore, it was the first and most important demographic census after the Great Union of 1918. The last census taken into consideration was the one in 2011, the second census of the 21st century. After obtaining the numerical data from the three censuses, we processed it using Microsoft Excel. Three tables were generated, emphasizing the numerical values and the percentages for each religion or confession for each census. The map depicting the geographic location of the study area was developed using GIS technology (ArcGis 10.3). We determined that Christians have been dominating the Apuseni Mountains and the Orthodox faith had and still has the most adherents. Likewise, the political-administrative factor heavily influenced census operations and also produced imbalances in the religious structure, especially after the 1948 abolition of the monarchy.

scholarly journals Failure patterns of different bracket systems and their influence on treatment duration: A retrospective cohort study

2018 ◽  
Vol 88 (3) ◽  
pp. 338-347 ◽  
Author(s):  
Dimitrios Stasinopoulos ◽  
Spyridon N. Papageorgiou ◽  
Frank Kirsch ◽  
Nikolaos Daratsianos ◽  
Andreas Jäger ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Cohort Study ◽  
Confidence Interval ◽  
Retrospective Cohort Study ◽  
Treatment Duration ◽  
Retrospective Cohort ◽  
Treatment Time ◽  
Failure Patterns ◽  
Ceramic Brackets ◽  
Bracket Failure

ABSTRACT Objectives: To compare the failure pattern of four different bracket types and to assess its effect on treatment duration. Materials and Methods: A total of 78 white patients (28 male, 50 female) with a mean age of 12.6 years were included in this retrospective cohort study and treated for a mean period of 30.6 months. The patients were treated in a private practice with stainless steel conventionally ligated brackets, ceramic conventionally ligated brackets, stainless steel self-ligating brackets, or nickel-free self-ligating brackets. The loss of at least one bracket during the course of treatment was analyzed with Cox proportional hazards survival analyses and generalized linear regression. Results: The overall bracket failure rate at the tooth level was 14.1% (217 brackets), with significant differences according to tooth type (between 8.0%–23.4%) and bracket type (between 11.2%–20.0%). After taking confounders into account, patients treated with ceramic brackets lost more brackets (hazard ratio = 1.62; 95% confidence interval = 1.14–2.29; P = .007) than patients with stainless steel brackets. On average, treatment time increased by 0.6 months (95% confidence interval = 0.21–1.05; P = .004) for each additional failed bracket. Conclusions: Bracket failure was more often observed with ceramic brackets and was associated with increased treatment duration.

Partial Amputation of Glans Penis During Mogen Clamp Circumcision

PEDIATRICS ◽  
1996 ◽  
Vol 97 (6) ◽  
pp. 906-907 ◽  
Author(s):  
Bruce S. Strimling
Keyword(s):  
United States ◽  
Numerical Data ◽  
The United States ◽  
The Other ◽  
Glans Penis ◽  
Partial Amputation ◽  
The One

Although no numerical data are available, the most common techniques for performing newborn circumcision in the United States involve the use of the Plastibell, the Gomco clamp, and the Mogen clamp, likely in that order. The Mogen clamp (see Fig 1 and 2) is the least familiar to most pediatricians. It has a number of advantages when compared with the other techniques: 1. the one size of the Mogen fits all; 2. it is the most rapid; 3. the Mogen instrument allows full visualization of exactly how much prepuce to remove. In Mogen circumcision however, the glans is not visualized before removal of the prepuce.

scholarly journals Development of an assembly for the realization of a transducer able to operate at very high temperatures

2019 ◽  
Vol 283 ◽  
pp. 07011
Author(s):  
Didier Flotté ◽  
David Macel ◽  
Abd Ennour Bouzenad ◽  
Frédéric Navacchia
Keyword(s):  
Stainless Steel ◽  
High Temperatures ◽  
Nuclear Reactor ◽  
New Technology ◽  
Operating Conditions ◽  
Equivalent Diameter ◽  
Assembly Technique ◽  
The One ◽  
Piezoelectric Disc ◽  
Very High

Monitoring the operation of the latest-generation nuclear reactor requires ultrasonic transducers able to operate at very high temperatures (> 600°C). To achieve this, CEA has requested from “Institut de Soudure” to help developing a new technology for these transducers compared to the one previously developed. This began with the development of a reliable assembly technique between a lithium niobate piezoelectric disc whose Curie temperature exceeds 1100°C and stainless steel discs. The chosen solution was to braze the niobate disc between two stainless steel discs. Parallel to this development, it was also necessary to develop a NDE procedure to verify the quality of the brazing assemblies. This development began with a simulation of immersion ultrasonic testing of the assemblies. The constraints were to be able to control the two brazed interfaces from the same access face, with the possibility of detecting and dimensioning defects with an equivalent diameter of 0.25 mm. This phase is important to define the optimal transducer with the associated operating conditions. The first assemblies validated the preliminary choices. To exploit the cartographies obtained, a signal processing procedure was developed. This enabled an automatic characterization of the indications observed. However, the analysis of the signals observed proved to be more complex than the one predicted by the simulation. Once the origin of the various observed signals was identified it was then possible to define windows allowing the construction of the cartographies to analyze. In case of a good quality assembly, it was possible to qualify the generated beam and to image it in the focal plane but with an observed signal having a very low damping. These first encouraging results, however, show that there is still some validation and development work to increase the sensitivity of the developed translator and its damping.

A Study on Warm Micro Backward Extrusion of SUS 304 Stainless Steel

2011 ◽  
Vol 486 ◽  
pp. 139-142
Author(s):  
Chao Cheng Chang ◽  
Dinh Hiep Nguyen ◽  
Hsin Sheng Hsiao
Keyword(s):  
Stainless Steel ◽  
Metal Forming ◽  
Material Flow ◽  
Elevated Temperatures ◽  
304 Stainless Steel ◽  
Electrical Heater ◽  
Backward Extrusion ◽  
Water Based ◽  
Inner Diameter ◽  
The One

A metal forming system comprising an electrical heater, capable of conducting processes at elevated temperatures, was developed to perform micro backward extrusion processes of SUS 304 stainless steel. Two punches with diameters of 1.6 mm and 1.8 mm were used to extrude the billets inside the die with an inner diameter of 2 mm. All processes were lubricated with water-based graphite and conducted under isothermal conditions at 400 °C. The results show that the developed extrusion system can be used to produce the stainless steel components with a micro cup-shaped profile. Moreover, the variation in the rim height of the cups produced by the 1.8 mm diameter punch is greater than the one by the 1.6 mm diameter punch. The results show that a decrease in the clearance between the punch and die could lead to an increase in the inhomogeneity of material flow in the micro backward extrusion processes.

Sign in / Sign up

Export Citation Format

Share Document