Economic viability of β titanium alloys for application in orthopedic implants

2017 ◽  
Author(s):  
Magna Bibiano de Oliveira ◽  
Alexandra de Oliveira França Hayama ◽  
Rubens Toledo
Keyword(s):  
Titanium Alloys ◽  
Orthopedic Implants ◽  
Economic Viability

scholarly journals Biomimetic Deposition of Hydroxyapatite Layer on Titanium Alloys

Micromachines ◽  
2021 ◽  
Vol 12 (12) ◽  
pp. 1447
Author(s):  
Madalina Simona Baltatu ◽  
Andrei Victor Sandu ◽  
Marcin Nabialek ◽  
Petrica Vizureanu ◽  
Gabriela Ciobanu
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloys ◽  
Orthopedic Implants ◽  
X Ray Diffraction ◽  
Metallic Biomaterials ◽  
Viable Solution ◽  
Indentation Tests ◽  
Good Biocompatibility ◽  
Materials Used ◽  
Micro Indentation

Over the last decade, researchers have been concerned with improving metallic biomaterials with proper and suitable properties for the human body. Ti-based alloys are widely used in the medical field for their good mechanical properties, corrosion resistance and biocompatibility. The TiMoZrTa system (TMZT) evidenced adequate mechanical properties, was closer to the human bone, and had a good biocompatibility. In order to highlight the osseointegration of the implants, a layer of hydroxyapatite (HA) was deposited using a biomimetic method, which simulates the natural growth of the bone. The coatings were examined by scanning electron microscopy (SEM), X-ray diffraction (XRD), micro indentation tests and contact angle. The data obtained show that the layer deposited on TiMoZrTa (TMZT) support is hydroxyapatite. Modifying the surface of titanium alloys represents a viable solution for increasing the osseointegration of materials used as implants. The studied coatings demonstrate a positive potential for use as dental and orthopedic implants.

Comparison of Functional Properties of Thin Layers on Titanium and Cobalt Implant Alloys

2010 ◽  
Vol 297-301 ◽  
pp. 1053-1058 ◽  
Author(s):  
Małgorzata Grądzka-Dahlke
Keyword(s):  
Wear Resistance ◽  
Corrosion Resistance ◽  
Titanium Alloys ◽  
Tribological Properties ◽  
Titanium Implant ◽  
Orthopedic Implants ◽  
Thin Layers ◽  
Tin Coating ◽  
Matrix Metal ◽  
Implant Alloys

The development of arthroplastics places high demands on the materials used for load-bearing elements of orthopedic implants. The most common of implant materials are titanium and cobalt alloys due to their excellent mechanical properties and biocompatibility. Titanium alloys have desirable properties, such as relatively low modulus, good fatigue strength, formability, machinability, superior corrosion resistance and so are frequently used for long-term implants. However, poor wear resistance limits their application for tribological systems of artificial joints. Research on improvement of titanium alloys tribological properties have been undertaken, mainly by using thin coatings. The TiN-layers are reported to be most promising in biomedical applications such. Many authors stress that application of TiN layer improve wear resistance of titanium implant alloys. Presented work is focused on comparison of effect of TiN coating on properties of TiAlV and CoCrMo implant alloys. The structure, microhardness, corrosion resistance as well as tribological properties were analysed. The research did not confirmed the good properties of titanium alloy with TiN coating. The results show that matrix metal hardness definitely affects the efficiency of TiN layers.

Electrophoretic Deposition Performance of Hydroxyapatite Coating on Titanium Alloys for Orthopedic Implant Application

2020 ◽  
Vol 1000 ◽  
pp. 69-81
Author(s):  
Nuzul Ficky Nuswantoro ◽  
Dian Juliadmi ◽  
Hidayatul Fajri ◽  
Menkher Manjas ◽  
Netti Suharti ◽  
...  
Keyword(s):  
Titanium Alloy ◽  
Titanium Alloys ◽  
Electrophoretic Deposition ◽  
Coating Layer ◽  
Low Cost ◽  
Titanium Implant ◽  
Orthopedic Implants ◽  
Metal Implants ◽  
Ha Coating ◽  
Coating Time

Hydroxyapatite (HA) is potentially used as a coating material for titanium alloys to improve their bioactivity and then enhancing the osseointegration characteristic of metal implants for orthopedic application. Electrophoretic Deposition (EPD), one of the coating methods that is widely applied for coating metal because of its simplicity and relatively low cost, is chosen for coating metal implants. HA coating layer quality can be controlled by adjusting applied voltages and coating time of the EPD process. However, the optimum voltage and exposing time has not yet been known for new type titanium implant such as Ti-12Cr and TNTZ. This work is, therefore, focusing on the effect of applied voltage and coating time on the mass growth, HA coating thickness, and surface coverage that can be produced on the surfaces of both alloys, and also on the conventional titanium alloy, Ti6Al4V, for comparison. The result of this work showed that there is a significant influence of the titanium alloy type on the HA layer performances. However, it is necessary to choose a suitable voltage and to expose time for producing a sufficient coating layer that meets the standard of orthopedic implants.

Diffusion of Oxygen in Ti-15Mo-xZr Alloys Studied by Anelastic Spectroscopy

2014 ◽  
Vol 354 ◽  
pp. 159-165 ◽  
Author(s):  
Fábio Bossoi Vicente ◽  
Carlos Roberto Grandini
Keyword(s):  
Crystal Structure ◽  
Mechanical Properties ◽  
Titanium Alloys ◽  
Diffusion Coefficients ◽  
Elasticity Modulus ◽  
Metallic Matrix ◽  
Orthopedic Implants ◽  
Exponential Factors ◽  
Effect Of Oxygen ◽  
Interstitial Elements

Because of their low elasticity modulus, titanium alloys have excellent biocompatibility, and are largely used in orthopedic prostheses. Among the properties that are beneficial for use in orthopedic implants is the elasticity modulus, which is closely connected to the crystal structure of the material. Interstitial elements, such as oxygen, change the mechanical properties of the material. Anelastic spectroscopy measurements are a powerful tool for the study of the interaction of these elements with the metallic matrix and substitutional solutes, providing information on the diffusion and concentration of interstitial elements. In this study, the effect of oxygen on the anelastic properties of alloys in the Ti-15Mo-Zr system was analyzed using anelastic spectroscopy measurements. The diffusion coefficients, pre-exponential factors, and activation energies of these alloys were calculated for oxygen.

Surface Modification of Orthopedic Implants Based on Titanium Alloys

2020 ◽  
Vol 36 (5) ◽  
pp. 31-40
Author(s):  
E.O. Nasakina ◽  
M.A. Sevostyanov ◽  
A.G. Kolmakov
Keyword(s):  
Corrosion Resistance ◽  
Surface Modification ◽  
Titanium Alloys ◽  
Polymer Coating ◽  
Ceramic Coating ◽  
Orthopedic Implants ◽  
Orthopedic Implant ◽  
Functional Coating ◽  
Reported Study ◽  
Modern Technologies

This review is devoted to modern technologies for various modifications of a surface of orthopedic implants made from titanium alloys. This approach will allow improving such characteristics of the implants as a corrosion resistance, biocompatibility and osteointegration. Modifications of titanium alloys with hydroxyapatite and calcium phosphate, multifunctional polymer or antibacterial coatings are considered. Analysis of the studies shows that the implant material can only provide a certain degree of biocompatibility and corrosion resistance, and that the nature and design of its surface have a strong influence on the body's response. Surface modification of implants is a good approach to overcome and solve various problems associated with the disadvantages of titanium alloys for orthopedic implants. titanium alloys, orthopedic implant, functional coating, ceramic coating, polymer coating, antibacterial coating The reported study was funded by RFBR, project No 19-18-50015.

Direct Observation of the Diffusionless β → β + ω Transformation in Titanium Alloys

1971 ◽  
Vol 29 ◽  
pp. 122-123
Author(s):  
N. E. Paton ◽  
D. de Fontaine ◽  
J. C. Williams
Keyword(s):  
Electron Microscope ◽  
Titanium Alloys ◽  
Direct Observation ◽  
Dark Field ◽  
X Ray Diffraction ◽  
Resistivity Measurements ◽  
Selected Area Electron Diffraction ◽  
Ti Alloys ◽  
Thin Foils ◽  
Field Device

The electron microscope has been used to study the diffusionless β → β + ω transformation occurring in certain titanium alloys at low temperatures. Evidence for such a transformation was obtained by Cometto et al by means of x-ray diffraction and resistivity measurements on a Ti-Nb alloy. The present work shows that this type of transformation can occur in several Ti alloys of suitable composition, and some of the details of the transformation are elucidated by means of direct observation in the electron microscope.Thin foils were examined in a Philips EM-300 electron microscope equipped with a uniaxial tilt, liquid nitrogen cooled, cold stage and a high resolution dark field device. Selected area electron diffraction was used to identify the phases present and the ω-phase was imaged in dark field by using a (101)ω reflection. Alloys were water quenched from 950°C, thinned, and mounted between copper grids to minimize temperature gradients in the foil.

The Ordered Phase Formation in Ti-Al-Ga Alloys

1970 ◽  
Vol 28 ◽  
pp. 440-441
Author(s):  
Shiro Fujishiro ◽  
Harold L. Gegel
Keyword(s):  
Thermal Stability ◽  
High Temperature ◽  
Titanium Alloys ◽  
Growth Kinetics ◽  
Stoichiometric Composition ◽  
Good Potential ◽  
Alpha Titanium ◽  
Cold Rolled ◽  
Kinetics Of ◽  
Thermal Stability Of

Ordered-alpha titanium alloys having a DO19 type structure have good potential for high temperature (600°C) applications, due to the thermal stability of the ordered phase and the inherent resistance to recrystallization of these alloys. Five different Ti-Al-Ga alloys consisting of equal atomic percents of aluminum and gallium solute additions up to the stoichiometric composition, Ti3(Al, Ga), were used to study the growth kinetics of the ordered phase and the nature of its interface.The alloys were homogenized in the beta region in a vacuum of about 5×10-7 torr, furnace cooled; reheated in air to 50°C below the alpha transus for hot working. The alloys were subsequently acid cleaned, annealed in vacuo, and cold rolled to about. 050 inch prior to additional homogenization

TEM characterization of reaction zone in a SiC fiber-reinforced titanium alloy

1988 ◽  
Vol 46 ◽  
pp. 738-739
Author(s):  
G. Das ◽  
R. E. Omlor
Keyword(s):  
Titanium Alloys ◽  
Reaction Zone ◽  
Carbon Layer ◽  
Fiber Reinforced ◽  
Reaction Products ◽  
Sic Fibers ◽  
Sic Fiber ◽  
The Matrix ◽  
Immense Potential

Fiber reinforced titanium alloys hold immense potential for applications in the aerospace industry. However, chemical reaction between the fibers and the titanium alloys at fabrication temperatures leads to the formation of brittle reaction products which limits their development. In the present study, coated SiC fibers have been used to evaluate the effects of surface coating on the reaction zone in the SiC/IMI829 system.IMI829 (Ti-5.5A1-3.5Sn-3.0Zr-0.3Mo-1Nb-0.3Si), a near alpha alloy, in the form of PREP powder (-35 mesh), was used a茸 the matrix. CVD grown AVCO SCS-6 SiC fibers were used as discontinuous reinforcements. These fibers of 142μm diameter contained an overlayer with high Si/C ratio on top of an amorphous carbon layer, the thickness of the coating being ∽ 1μm. SCS-6 fibers, broken into ∽ 2mm lengths, were mixed with IMI829 powder (representing < 0.1vol%) and the mixture was consolidated by HIP'ing at 871°C/0. 28GPa/4h.

High-resolution EM investigation about effect of stress on formation of ω-phase crystals in β-tttanium alloys

1996 ◽  
Vol 54 ◽  
pp. 1006-1007
Author(s):  
E. Sukedai ◽  
M. Shimoda ◽  
A. Fujita ◽  
H. Nishizawa ◽  
H. Hashimoto
Keyword(s):  
High Resolution ◽  
Titanium Alloys ◽  
High Resolution Electron Microscopy ◽  
Dark Field ◽  
Zone Refining ◽  
Ω Phase ◽  
Α Phase ◽  
Nucleation Sites ◽  
Resolution Electron ◽  
Bcc Structure

ω-phase particles formed in β-titanium alloys (bcc structure) act important roles to their mechanical properties such as ductility and hardness. About the ductility, fine ω-phase particles in β–titanium alloys improve the ductility, because ω-phase crystals becomes nucleation sites of α-phase and it is well known that (β+α) duplex alloys have higher ductility. In the present study, the formation sites and the formation mechanism of ω-phase crystals due to external stress and aging are investigated using the conventional and high resolution electron microscopy.A β-titanium alloy (Til5Mo5Zr) was supplied by Kobe Steel Co., and a single crystal was prepared by a zone refining method. Plates with {110} surface were cut from the crystal and were pressured hydrostatically, and stressed by rolling and tensile testing. Specimens for aging with tensile stress were also prepared from Ti20Mo polycrystals. TEM specimens from these specimens were prepared by a twin-jet electron-polishing machine. A JEM 4000EX electron microscope operated at 400k V was used for taking dark field and HREM images.

Sign in / Sign up

Export Citation Format

Share Document