3-D Defect Localization by Measurement and Modeling of the Dynamics of Heat Transport in Deep Sub-Micron Devices

2007 ◽  
Author(s):  
A. Reverdy ◽  
M. de la Bardonnie ◽  
L.F.Tz. Kwakman ◽  
M. Lamy ◽  
C. Wyon ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Success Rate ◽  
Heat Transport ◽  
Fault Isolation ◽  
Isolation Method ◽  
Signal Phase ◽  
Resistance Change ◽  
Time Constants ◽  
Measurement Results ◽  
Defect Localization

Abstract Due to relentless down scaling of device geometries, failure analysis is getting more and more complex. As a matter of fact, the success rate of Thermal Laser Stimulation (TLS) techniques drops significantly for 90/65 nm CMOS devices because of the lack of x, y and z accuracy. In our aim to improve the TLS based fault isolation method, we have studied thermal time-constant signatures using a Modulated Optical Beam Induced Resistance Change (MOBIRCH) technique that may provide accurate x and y submicron resolution as well as depth or z-information of defects in the interconnection part of devices. Both Modeling and measurement results indicate that OBIRCH signal phase shifts and heat-up & cool-down time constants indeed do correlate with the location, dimensions and density of the structures studied.

Application of Focused Ion Beam System as A Defect Localization and Root Cause Analysis Tool

2001 ◽  
Author(s):  
C.C. Ooi ◽  
K.H. Siek ◽  
K.S. Sim
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Fault Isolation ◽  
Analysis Tool ◽  
Root Cause ◽  
Beam System ◽  
Defect Localization ◽  
Challenging Environment ◽  
Microprocessor Technology

Abstract Focused ion beam system has been widely used as a critical failure analysis tool as microprocessor technology advances at a ramping speed. It has become an essential step in failure analysis to reveal physical defects post electrical fault isolation. In this highly competitive and challenging environment prevalent today, failure analysis throughput time is of utmost important. Therefore quick, efficient and reliable physical failure analysis technique is needed to avoid potential issues from becoming bigger. This paper will discuss the applications of FIB as a defect localization and root cause determination tool through the passive charge contrast technique and pattern FIB analysis.

Advanced CMOS Device Fault Isolation Using Frequency Mapping on Passive Structures

2013 ◽  
Author(s):  
S.H. Goh ◽  
B.L. Yeoh ◽  
G.F. You ◽  
W.H. Hung ◽  
Jeffrey Lam ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Fault Isolation ◽  
Device Failure ◽  
Functional Failure ◽  
Technology Node ◽  
Defect Localization ◽  
Emission Microscopy ◽  
Scan Chains

Abstract Backside frequency mapping on modulating active in transistors is well established for defect localization on broken scan chains. Recent experiments have proven the existence of frequency signals from passive structures modulations. In this paper, we demonstrate the effectiveness of this technique on a 65 nm technology node device failure. A resistive leaky path leading to a functional failure which, otherwise cannot be isolated using dynamic emission microscopy, is localized in this work to guide follow on failure analysis.

Improving Fault Isolation Using Iterative Diagnosis

2008 ◽  
Author(s):  
Kevin Gearhardt ◽  
Chris Schuermyer ◽  
Ruifeng Guo
Keyword(s):  
Fault Diagnosis ◽  
Failure Analysis ◽  
Test Generation ◽  
Pattern Generation ◽  
Fault Isolation ◽  
Isolation Techniques ◽  
Defect Localization

Abstract This paper presents an iterative diagnosis test generation framework to improve logic fault diagnosis resolution. Industrial examples are presented in this paper on how additional targeted pattern generation can be used to improve defect localization before physical failure analysis of a die. This enables failure analysts to be more effective by reducing the dependence on the more expensive physical fault isolation techniques.

Backside Deprocessing of CMOS SOI Devices for Physical Defect and Failure Analysis

2003 ◽  
Author(s):  
Seth J. Prejean ◽  
Joseph Shannon
Keyword(s):  
Integrated Circuits ◽  
Failure Analysis ◽  
Flip Chip ◽  
Fault Isolation ◽  
Oxide Semiconductor ◽  
Easy Access ◽  
Induced Voltage ◽  
Emission Analysis ◽  
Defect Localization ◽  
Soi Devices

Abstract This paper describes improvements in backside deprocessing of CMOS (Complimentary Metal Oxide Semiconductor) SOI (Silicon On Insulator) integrated circuits. The deprocessing techniques described here have been adapted from a previous research publication on backside deprocessing of bulk CMOS integrated circuits [1]. The focus of these improvements was to provide a repeatable and reliable methodology of deprocessing CMOS devices from the backside. We describe a repeatable and efficient technique to deprocess flip chip packaged devices and unpackaged die from the backside. While this technique has been demonstrated on SOI and bulk devices, this paper will focus on the latest SOI technology. The technique is useful for quick and easy access to the transistor level while preserving the metal interconnects for further analysis. It is also useful for deprocessing already thinned or polished die without removing them from the package. Removing a thin die from a package is very difficult and could potentially damage the device. This is especially beneficial when performing physical failure analysis of samples that have been back thinned for the purpose of fault isolation and defect localization techniques such as: LIVA (Laser Induced Voltage Alteration), TIVA (Thermally Induce Voltage Alteration), SDL [2] (Soft Defect Localization), and TRE (Time Resolved Emission) analysis. An important fundamental advantage of deprocessing SOI devices is that the BOX (Buried Oxide) layer acts as a chemical etch stop when etching the backside or bulk silicon. This leaves the transistor active silicon intact for analysis. Further delayering allows for the inspection of the active silicon, gate oxide, silicide, spacers, and poly. After deprocessing the transistor level, the metal layers are still intact and, in most cases, still electrically connected to the outside world. This can provide additional failure analysis opportunities.

Laser Based Defect Localization for the Failure Analysis of Advanced Product

2006 ◽  
Author(s):  
W.Y. Cheng ◽  
T.Y. Chiu ◽  
Jon C. Lee ◽  
J.Y. Chiou
Keyword(s):  
Failure Analysis ◽  
Laser Scanning ◽  
Failure Modes ◽  
Induced Voltage ◽  
Resistance Change ◽  
Thermally Induced ◽  
Defect Localization ◽  
Defect Isolation ◽  
Site Localization ◽  
Selection Of

Abstract Emission microscopy have been used for failure analysis (FA) defect isolation. But for advanced products, the working voltage of chip is getting smaller, thus many emission spots from normal transistors will be observed, which indeed affects the judgment on the emission spots from killer defects and increases the FA difficulty. Laser scanning microscope (LSM)-based techniques have been powerful defect isolation methods for many years. In this study, Checkpoint Infrascan 200TD, a laser-based tool, is used to perform defect localization. Here, thermally induced voltage alteration and optical beam induced resistance change are used to get defect locations. The study demonstrates three FA cases with 80nm/90nm technologies; metal direct short, poly leakage, and contact high resistance are also found in these cases. It is concluded that, by the selection of control parameters, Infrascan 200TD provides several capabilities of failure site localization and can be applied to different failure modes.

Zynq SOC Low-Voltage and Temperature-Dependent L2 Cache Failure Diagnosis and Defect Localization Case Study

2017 ◽  
Author(s):  
Haonan Bai ◽  
Lan Yin Lee ◽  
Yang Jing ◽  
Peter Floyd Salinas ◽  
Kok Keng Chua
Keyword(s):  
Failure Analysis ◽  
Low Voltage ◽  
Data Access ◽  
Pattern Generation ◽  
Fault Isolation ◽  
Programmable Logic ◽  
Single Chip ◽  
Tem Analysis ◽  
Test Methodology ◽  
Defect Localization

Abstract Failure analysis and defect localization on 28nm All Programmable Zynq System-on-Chip (SoC) device is extremely challenging. While conventional FPGA, which only consists of the Programmable Logic, has greater ease and flexibility in pattern generation during fault isolation, the all programmable SoC device integrates a dual ARM Cortex-A9 cores with Programmable Logic (PL) in a single chip. The cache data access in-between processor and PL is more complex and test methodology has lesser degree of control on cache data flow and stack sequence. This paper introduced an advanced fault isolation test methodology combining Software Development Kit (SDK) with scan based diagnostic test for cache failures. It successfully pinpoint to failure locations with physical defects found. As conventional physical failure analysis approaches using SEM based passive voltage contrast could not observe any abnormalities, current imaging and nano-probing measurement using AFP played critical roles in detecting nano-ampere leakages prior subsequent TEM analysis. The findings were then feedback to the foundry for process improvement. Furthermore, a new screening methodology is innovated where an extreme low-voltage test at high temperature in Automatic Test to detect and eliminate the process marginal leakage failure.

MEMS Failure Analysis In Wafer Fabrication

2016 ◽  
Author(s):  
Hui Peng Ng ◽  
Angela Teo ◽  
Ghim Boon Ang ◽  
Alfred Quah ◽  
N. Dayanand ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Case Studies ◽  
Data Interpretation ◽  
Fault Isolation ◽  
Wafer Fabrication ◽  
Auger Analysis ◽  
Root Cause ◽  
Defect Site ◽  
Defect Localization ◽  
Cmos Chip

Abstract This paper discussed on how the importance of failure analysis to identify the root cause and mechanism that resulted in the MEMS failure. The defect seen was either directly on the MEMS caps or the CMOS integrated chip in wafer fabrication. Two case studies were highlighted in the discussion to demonstrate how the FA procedures that the analysts had adopted in order to narrow down to the defect site successfully on MEMS cap as well as on CMOS chip on MEMS package units. Besides the use of electrical fault isolation tool/technique such as TIVA for defect localization, a new physical deprocessing approach based on the cutting method was performed on the MEMS package unit in order to separate the MEMS from the Si Cap. This approach would definitely help to prevent the introduction of particles and artifacts during the PFA that could mislead the FA analyst into wrong data interpretation. Other FA tool such as SEM inspection to observe the physical defect and Auger analysis to identify the elements in the defect during the course of analysis were also documented in this paper.

Single Device Characterization by Nano-probing to Identify Failure Root Cause

2005 ◽  
Author(s):  
Chao-Chi Wu ◽  
Jon C. Lee ◽  
Jung-Hsiang Chuang ◽  
Tsung-Te Li
Keyword(s):  
Failure Analysis ◽  
Success Rate ◽  
Failure Mechanism ◽  
Fault Isolation ◽  
Device Characterization ◽  
Nano Technology ◽  
Analysis Techniques ◽  
Root Cause ◽  
Visual Defects ◽  
Lower Success Rate

Abstract In general failure analysis cases, a less invasive fault isolation approach can be utilized to resolve a visual root cause defect. In the case of nano technology, visual defects are not readily resolved, due to an increase in non-visible defects. The nonvisible defects result in a lower success rate since conventional FA methods/tools are not efficient in identifying the failure root cause. For the advanced nanometer process, this phenomenon is becoming more common; therefore the utilization of advanced techniques are required to get more evidence to resolve the failure mechanism. The use of nanoprobe technology enables advanced device characterization h order to obtain more clues to the possible failure mechanism before utilizing the traditional physical failure analysis techniques.

Probeless FA Approach: A Breakthrough Simulation Based Failure Analysis Method

2002 ◽  
Author(s):  
ChoonHou Lock ◽  
YikChoong Wong ◽  
KahHee Siek
Keyword(s):  
Failure Analysis ◽  
Success Rate ◽  
Analysis Time ◽  
Analysis Method ◽  
Signal Value ◽  
Simulation Based ◽  
Defect Localization ◽  
Internal Signal

Abstract A breakthrough approach was developed in which failure analysis (FA) of advanced microprocessor was carried out without the use of defect localization equipment. This technique enables the reading of internal signal value without the use of any physical probing method. This method demonstrates the same FA capability with higher success rate and shorter analysis time.

Application of PEM and OBIRCH to Defect Localization of Integrated Circuits

2014 ◽  
Vol 904 ◽  
pp. 277-281
Author(s):  
Jian Wen Lian ◽  
Xiao Ling Lin ◽  
Ruo He Yao
Keyword(s):  
Integrated Circuits ◽  
Failure Mechanisms ◽  
Photon Emission ◽  
Fault Isolation ◽  
Resistance Change ◽  
Microelectronic Devices ◽  
Application Condition ◽  
Defect Localization ◽  
Metal Interconnects ◽  
Fault Characterization

With the increasing integration and complexity of microelectronic devices, fault isolation has been challenged. Photon Emission Microscopy (PEM) and Optical Beam Induced Resistance Change (OBIRCH) are effective tools for defect localization and fault characterization in failure analysis. In this paper, the principles and different application condition of PEM and OBIRCH are discussed. PEM is very helpful for locating defects emitting photon, but can not detect the defects which have no photon emitting, such as shorted metal interconnects; OBIRCH as a complementary, has a high success rate for locating resistance defects. Two cases with failure mechanisms illuminated are presented to show the different application of PEM and OBIRCH.

Sign in / Sign up

Export Citation Format

Share Document