MEMS Failure Analysis In Wafer Fabrication

2016 ◽  
Author(s):  
Hui Peng Ng ◽  
Angela Teo ◽  
Ghim Boon Ang ◽  
Alfred Quah ◽  
N. Dayanand ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Case Studies ◽  
Data Interpretation ◽  
Fault Isolation ◽  
Wafer Fabrication ◽  
Auger Analysis ◽  
Root Cause ◽  
Defect Site ◽  
Defect Localization ◽  
Cmos Chip

Abstract This paper discussed on how the importance of failure analysis to identify the root cause and mechanism that resulted in the MEMS failure. The defect seen was either directly on the MEMS caps or the CMOS integrated chip in wafer fabrication. Two case studies were highlighted in the discussion to demonstrate how the FA procedures that the analysts had adopted in order to narrow down to the defect site successfully on MEMS cap as well as on CMOS chip on MEMS package units. Besides the use of electrical fault isolation tool/technique such as TIVA for defect localization, a new physical deprocessing approach based on the cutting method was performed on the MEMS package unit in order to separate the MEMS from the Si Cap. This approach would definitely help to prevent the introduction of particles and artifacts during the PFA that could mislead the FA analyst into wrong data interpretation. Other FA tool such as SEM inspection to observe the physical defect and Auger analysis to identify the elements in the defect during the course of analysis were also documented in this paper.

A New Failure Analysis Flow of Gate Oxide Integrity Failure in Wafer Fabrication

2009 ◽  
Author(s):  
Hua Younan ◽  
Chu Susan ◽  
Gui Dong ◽  
Mo Zhiqiang ◽  
Xing Zhenxiang ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Gate Dielectric ◽  
Dielectric Breakdown ◽  
Defect Density ◽  
Gate Oxide ◽  
Oxide Thickness ◽  
Fault Isolation ◽  
Wafer Fabrication ◽  
Root Cause ◽  
Gate Oxide Integrity

Abstract As device feature size continues to shrink, the reducing gate oxide thickness puts more stringent requirements on gate dielectric quality in terms of defect density and contamination concentration. As a result, analyzing gate oxide integrity and dielectric breakdown failures during wafer fabrication becomes more difficult. Using a traditional FA flow and methods some defects were observed after electrical fault isolation using emission microscopic tools such as EMMI and TIVA. Even with some success with conventional FA the root cause was unclear. In this paper, we will propose an analysis flow for GOI failures to improve FA’s success rate. In this new proposed flow both a chemical method, Wright Etch, and SIMS analysis techniques are employed to identify root cause of the GOI failures after EFA fault isolation. In general, the shape of the defect might provide information as to the root cause of the GOI failure, whether related to PID or contamination. However, Wright Etch results are inadequate to answer the questions of whether the failure is caused by contamination or not. If there is a contaminate another technique is required to determine what the contaminant is and where it comes from. If the failure is confirmed to be due to contamination, SIMS is used to further determine the contamination source at the ppm-ppb level. In this paper, a real case of GOI failure will be discussed and presented. Using the new failure analysis flow, the root cause was identified to be iron contamination introduced from a worn out part made of stainless steel.

Application of Focused Ion Beam System as A Defect Localization and Root Cause Analysis Tool

2001 ◽  
Author(s):  
C.C. Ooi ◽  
K.H. Siek ◽  
K.S. Sim
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Fault Isolation ◽  
Analysis Tool ◽  
Root Cause ◽  
Beam System ◽  
Defect Localization ◽  
Challenging Environment ◽  
Microprocessor Technology

Abstract Focused ion beam system has been widely used as a critical failure analysis tool as microprocessor technology advances at a ramping speed. It has become an essential step in failure analysis to reveal physical defects post electrical fault isolation. In this highly competitive and challenging environment prevalent today, failure analysis throughput time is of utmost important. Therefore quick, efficient and reliable physical failure analysis technique is needed to avoid potential issues from becoming bigger. This paper will discuss the applications of FIB as a defect localization and root cause determination tool through the passive charge contrast technique and pattern FIB analysis.

Challenges of System Level Failure Analysis of Electronics in the Automotive Industry

2017 ◽  
Author(s):  
Bence Hevesi
Keyword(s):  
Failure Analysis ◽  
Case Studies ◽  
Automotive Industry ◽  
Root Cause Analysis ◽  
Fault Isolation ◽  
System Level ◽  
Cause Analysis ◽  
Root Cause ◽  
Analysis Workflow

Abstract In this paper, different failure analysis (FA) workflows are showed which combines different FA approaches for fast and efficient fault isolation and root cause analysis in system level products. Two case studies will be presented to show the importance of a well-adjusted failure analysis workflow.

Laser Voltage Probing in Failure Analysis of Advanced Integrated Circuits on SOI

2012 ◽  
Author(s):  
V.K. Ravikumar ◽  
R. Wampler ◽  
M.Y. Ho ◽  
J. Christensen ◽  
S.L. Phoa
Keyword(s):  
Integrated Circuits ◽  
Failure Analysis ◽  
Case Studies ◽  
Timing Analysis ◽  
Fault Isolation ◽  
Root Cause ◽  
Root Cause Identification

Abstract Laser voltage probing is the newest generation of tools that perform timing analysis for electrical fault isolation in advanced failure analysis facilities. This paper uses failure analysis case studies on SOI to showcase the implementation of laser voltage probing in the failure analysis flow and highlight its significance in root-cause identification.

Using NI-PXI Test Platform in Soft Defect Localization of Temperature Dependent Failures

2020 ◽  
Author(s):  
Jed Paolo Deligente ◽  
Saidaliah Sarip
Keyword(s):  
Failure Analysis ◽  
Case Studies ◽  
Failure Mode ◽  
Fault Isolation ◽  
Temperature Dependent ◽  
Labview Software ◽  
Dependent Failures ◽  
Analysis Technique ◽  
Test Platform ◽  
Defect Localization

Abstract Soft Defect Localization (SDL) method has been a common failure analysis technique used in fault isolation of temperature dependent failures, however proper signal conditioning and conversion of the monitored signal into a pass/fail signal are critical in acquiring an accurate defect location. This paper presents case studies where LabVIEW software using NI-PXI test platform was successfully implemented to effectively convert the failure mode into a pass/fail signal which provided a reliable SDL result.

SEM-Based Nanoprobing on 40, 32 and 28 nm CMOS Devices Challenges for Semiconductor Failure Analysis

2013 ◽  
Author(s):  
Erik Paul ◽  
Holger Herzog ◽  
Sören Jansen ◽  
Christian Hobert ◽  
Eckhard Langer
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
Scanning Electron Microscope ◽  
Failure Analysis ◽  
Case Studies ◽  
State Of The Art ◽  
Root Cause ◽  
Highly Efficient ◽  
Technology Nodes ◽  
Scanning Electron

Abstract This paper presents an effective device-level failure analysis (FA) method which uses a high-resolution low-kV Scanning Electron Microscope (SEM) in combination with an integrated state-of-the-art nanomanipulator to locate and characterize single defects in failing CMOS devices. The presented case studies utilize several FA-techniques in combination with SEM-based nanoprobing for nanometer node technologies and demonstrate how these methods are used to investigate the root cause of IC device failures. The methodology represents a highly-efficient physical failure analysis flow for 28nm and larger technology nodes.

Failure Analysis of Killer Defects and Yield Enhancement of Flat ROM Devices in Wafer Fabrication

2000 ◽  
Author(s):  
Y. N. Hua ◽  
Z. R. Guo ◽  
L. H. An ◽  
Shailesh Redkar
Keyword(s):  
Electron Microscope ◽  
Failure Analysis ◽  
Fault Isolation ◽  
Yield Enhancement ◽  
Wafer Fabrication ◽  
X Ray ◽  
Particle Contamination ◽  
Emission Microscopy ◽  
Microscopy Techniques ◽  
Scanning Electron

Abstract In this paper, some low yield cases in Flat ROM device (0.45 and 0.6 µm) were investigated. To find killer defects and particle contamination, KLA, bitmap and emission microscopy techniques were used in fault isolation. Reactive ion etching (RIE) and chemical delayering, 155 Wright Etch, BN+ Etch and scanning electron microscope (SEM) were used for identification and inspection of defects. In addition, energy-dispersive X-ray microanalysis (EDX) was used to determine the composition of the particle or contamination. During failure analysis, seven kinds of killer defects and three killer particles were found in Flat ROM devices. The possible root causes, mechanisms and elimination solutions of these killer defects/particles were also discussed.

Application of AFP in Resolving Systematic Issue in Wafer Fabrication

2013 ◽  
Author(s):  
Hui Peng Ng ◽  
Ghim Boon Ang ◽  
Chang Qing Chen ◽  
Alfred Quah ◽  
Angela Teo ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Case Studies ◽  
Failure Mechanisms ◽  
Critical Role ◽  
Electrical Characterization ◽  
Process Technology ◽  
Atomic Force ◽  
Defect Localization ◽  
Non Volatile Memory ◽  
Visual Failure

Abstract With the evolution of advanced process technology, failure analysis is becoming much more challenging and difficult particularly with an increase in more erratic defect types arising from non-visual failure mechanisms. Conventional FA techniques work well in failure analysis on defectively related issue. However, for soft defect localization such as S/D leakage or short due to design related, it may not be simple to identify it. AFP and its applications have been successfully engaged to overcome such shortcoming, In this paper, two case studies on systematic issues due to soft failures were discussed to illustrate the AFP critical role in current failure analysis field on these areas. In other words, these two case studies will demonstrate how Atomic Force Probing combined with Scanning Capacitance Microscopy were used to characterize failing transistors in non-volatile memory, identify possible failure mechanisms and enable device/ process engineers to make adjustment on process based on the electrical characterization result. [1]

Pseudo-Dynamic Fault Isolation Technique Using Backside Emission Microscopy – Case Study, Where All Other Methods Fail

2002 ◽  
Author(s):  
Yoav Weizman ◽  
Ezra Baruch ◽  
Michael Zimin
Keyword(s):  
Failure Analysis ◽  
Process Variations ◽  
Fault Isolation ◽  
Operating Conditions ◽  
Detection Sensitivity ◽  
Isolation Technique ◽  
Root Cause ◽  
Emission Microscopy ◽  
Failure Location ◽  
Noisy Background

Abstract Emission microscopy is usually implemented for static operating conditions of the DUT. Under dynamic operation it is nearly impossible to identify a failure out of the noisy background. In this paper we describe a simple technique that could be used in cases where the temporal location of the failure was identified however the physical location is not known or partially known. The technique was originally introduced to investigate IDDq failures (1) in order to investigate timing related issues with automated tester equipment. Ishii et al (2) improved the technique and coupled an emission microscope to the tester for functional failure analysis of DRAMs and logic LSIs. Using consecutive step-by-step tester halting coupled to a sensitive emission microscope, one is able detect the failure while it occurs. We will describe a failure analysis case in which marginal design and process variations combined to create contention at certain logic states. Since the failure occurred arbitrarily, the use of the traditional LVP, that requires a stable failure, misled the analysts. Furthermore, even if we used advanced tools as PICA, which was actually designed to locate such failures, we believe that there would have been little chance of observing the failure since the failure appeared only below 1.3V where the PICA tool has diminished photon detection sensitivity. For this case the step-by-step halting technique helped to isolate the failure location after a short round of measurements. With the use of logic simulations, the root cause of the failure was clear once the failing gate was known.

Lock-in Thermography for Flip-Chip Package Failure Analysis

2012 ◽  
Author(s):  
Lihong Cao ◽  
Manasa Venkata ◽  
Jeffery Huynh ◽  
Joseph Tan ◽  
Meng-Yeow Tay ◽  
...  
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Case Studies ◽  
Flip Chip ◽  
Organic Substrate ◽  
Fault Isolation ◽  
Lock In

Abstract This paper describes the application of lock-in thermography (LIT) for flip-chip package-level failure analysis. LIT successfully detected and localized short failures related to both die/C4 bumps and package defects inside the organic substrate. The detail sample preparation to create short defects at different layers, LIT fault isolation methodology, and case studies performed with LIT are also presented in this paper.

Sign in / Sign up

Export Citation Format

Share Document