Investigation of the Silicon Loss in APS MoSi2 under Typical Spray Conditions

1996 ◽  
Author(s):  
K.J. Hollis ◽  
A. Bartlett ◽  
R.G. Castro ◽  
R.A. Neiser
Keyword(s):  
Particle Trajectory ◽  
Particle Temperature ◽  
Sem Analysis ◽  
Empirical Models ◽  
Spray Parameters ◽  
X Ray Diffraction ◽  
Temperature Oxidation ◽  
X Ray ◽  
Plasma Sprayed ◽  
Oxidation And Corrosion

Abstract MoSi2 provides good high temperature oxidation and corrosion resistance. However, the lower silicides such as MosSis do not provide such resistance. In this study, atmosphereic plasma sprayed (APS) MoSi2 particle temperatures and velocities were measured under various torch conditions chosen to span the majority of typically utilized spray parameters. Empirical models of particle temperature and velocity were computed from the data. Three spray conditions were chosen to produce high, medium and low particle temperatures and velocities. Coatings produced under these spray conditions were characterized by profile tracing, quantitative x-ray diffraction, and SEM analysis. The Mo5Si3 level in the coatings ranged from 5% to 8% while the Mo5Si3 level in the starting powder was 0.6%. Particle size, particle trajectory, and torch parameters were found to be important factors in the Si loss process when APS depositing MoSi2.

Preparation and Characteristic of PSMA/EG Composite Materials

2010 ◽  
Vol 163-167 ◽  
pp. 1951-1954
Author(s):  
Gui Xiang Hou ◽  
Hai Ning Na ◽  
Xiao Ming Sang
Keyword(s):  
High Temperature Oxidation ◽  
In Situ Polymerization ◽  
Expanded Graphite ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
Temperature Oxidation ◽  
X Ray ◽  
Graphite Nanosheets ◽  
Composite Granules

Graphite nanosheets prepared through high-temperature oxidation via powdering the expanded graphite. After soaking the expanded graphite with styrene(S) and maleic anhydride(MA) monomers, the polymer (Poly(S-co-MA))/expanded graphite(EG) (PSMA/EG) composite granules were obtained by in situ polymerization. Light microscope，scanning electron microscope and X-ray diffraction characterization were performed. SEM analysis indicate that the expanded graphite was mostly tore to sheets with thickness of 50–80 nm and with diameter of 1μm. Optical micrographs showed that the distribution of graphite platelets is found to be nearly uniform.

An Investigation of Al-Rich Alloys in the Al-Cr-Ru System

2001 ◽  
Vol 7 (S2) ◽  
pp. 1248-1249
Author(s):  
D.N. Compton ◽  
L.A. Cornish ◽  
M.J. Witcomb
Keyword(s):  
High Temperature Oxidation ◽  
Solid Phase ◽  
Liquidus Surface ◽  
X Ray Diffraction ◽  
Phase Boundaries ◽  
Temperature Oxidation ◽  
X Ray ◽  
Al Content ◽  
Cast Alloys ◽  
Oxidation And Corrosion

Many aerospace components that operate in aggressive environments make use of coating techniques for protection. One of the alloy systems used in these coatings is Al-Cr-Ru, with typical alloy compositions between 20-35 at.% Al and 20-35 at.% Ru. Alloys with a higher Al content may provide protection through an aluminium oxide (AI2O3) scale which is resistant to high-temperature oxidation and corrosion. However, Al-rich alloys in the Al-Cr-Ru system have not been thoroughly investigated. Previously, the phase boundaries of the binary phases, except AI9Cr4, into the ternary were established. The two ternary phases (Ternary 1 and Ternary 2) were identified, although their phase boundaries were unclear. Thus more alloys have been studied to enable the liquidus surface, the solid phase projection and the 600°C isothermal projection to be drawn.As-cast alloys were examined metallographically in the scanning electron microscope. The phases present were confirmed by X-ray diffraction, and the compositions obtained by energy dispersive Xray spectroscopy.

Structure and Electrochemical Behavior of Plasma-Sprayed LSGM Electrolyte Films

2002 ◽  
Vol 756 ◽  
Author(s):  
H. Zhang ◽  
X. Ma ◽  
J. Dai ◽  
S. Hui ◽  
J. Roth ◽  
...  
Keyword(s):  
Electrochemical Behavior ◽  
Electrochemical Impedance ◽  
Amorphous Structure ◽  
Solid Oxide ◽  
X Ray Diffraction ◽  
X Ray ◽  
Spray Process ◽  
Plasma Spray Process ◽  
Electrolyte Film ◽  
Plasma Sprayed

ABSTRACTAn intermediate temperature solid oxide fuel cell (SOFC) electrolyte film of La0.8Sr 0.2Ga0.8Mg0.2O2.8 (LSGM) was fabricated using a plasma spray process. The microstructure and phase were investigated using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrochemical behavior of the thermal sprayed LSGM film was investigated using electrochemical impedance spectroscopy (EIS). The study indicates that thermal spray can deposit a dense LSGM layer. It was found that the rapid cooling in the thermal process led to an amorphous or poor crystalline LSGM deposited layer. This amorphous structure has a significant effect on the performance of the cell. Crystallization of the deposited LSGM layer was observed during annealing between 500–600 °C. After annealing at 800 °C, the ionic conductivity of the sprayed LSGM layer can reach the same level as that of the sintered LSGM.

Simultaneous Independent Measurement of Splat Diameter and Cooling Time during Impact on a Substrate of Plasma Sprayed Molybdenum Particles

1997 ◽  
Author(s):  
P. Gougeon ◽  
C. Moreau
Keyword(s):  
High Speed ◽  
Thermal Emission ◽  
Particle Temperature ◽  
Cooling Time ◽  
Spray Parameters ◽  
Coating Structure ◽  
Molten Droplets ◽  
Plasma Sprayed ◽  
The Impact ◽  
Molybdenum Particles

Abstract In thermal spray processes, the coating structure is the result of flattening and cooling of molten droplets on the substrate. The study of the cooling time and evolution of the splat size during impact is then of the highest importance to understand the influence of the spray parameters and substrate characteristics on the coating structure. Measurement of particle temperature during impact requires the use of a high-speed 2-color pyrometer to collect the thermal emission of the particle during flattening. Simultaneous measurement of the splat size with this pyrometer is difficult since the size of the particle can change as it cools down. To measure the splat size independently, a new measurement technique has been developed. In this technique the splat size is measured from the attenuation of the radiation of a laser beam illuminating the particle during impact. Results are presented for plasma sprayed molybdenum particles impacting on a glass substrate at room temperature. It is shown that the molybdenum splat reaches its maximum extent about 2 microseconds after the impact. In this work, we show that this increase of the splat surface is followed by a phase during which the splat size decreases significantly during 2 to 3 microseconds.

Development of Ternary Concrete Utilizing Agricultural Waste Material

2022 ◽  
Author(s):  
Sunita Kumari ◽  
Dhirendra Singhal ◽  
Rinku Walia ◽  
Ajay Rathee
Keyword(s):  
Rice Husk ◽  
Rice Husk Ash ◽  
Agricultural Waste ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Concrete Mix ◽  
Maize Cob

Abstract The present project proposes to utilize rice husk and maize cob husk ash in the cement to mitigate the adverse impact of cement on environment and to enhance the disposal of waste in a sustainable manner. Ternary concrete / MR concrete was prepared by using rise husk and maize cob ash with cement. For the present project, five concrete mixes MR-0 (Control mix), MR-1 (Rice husk ash 10% and MR-2.5%), MR-2 (Rice husk ash 10% and MR-5%), MR-3 (Rice husk ash 10% and MR-2.5%), MR-4 (Rice husk ash 10% and MR-2.5%) were prepared. M35 concrete mix was designed as per IS 10262:2009 for low slump values 0-25mm. The purpose is to find the optimum replacement level of cement in M35 grade ternary concrete for I – Shaped paver blocks.In order to study the effects of these additions, micro-structural and structural properties test of concretes have been conducted. The crystalline properties of control mix and modified concrete are analyzed by Fourier Transform Infrared Spectroscope (FTIR), Scanning Electron Microscopy (SEM), and X-Ray Diffraction (XRD). The results indicated that 10% Rice husk ash and 5% maize cob ash replaced with cement produce a desirable quality of ternary concrete mix having good compressive strength. The results of SEM analysis indicated that the morphology of both concrete were different, showing porous structure at 7 days age and become unsymmetrical with the addition of ashes. After 28 day age, the control mix contained more quantity of ettringite and became denser than ternary concrete. XRD analysis revealed the presence of portlandite in large quantity in controlled mix concrete while MR concrete had the partially hydrated particle of alite.

Effect of Compressive Stress on the High-Temperature Oxidation Behavior of a Fe-20Ni Alloy in Air

2018 ◽  
Vol 921 ◽  
pp. 168-176
Author(s):  
Chang Hai Zhou ◽  
Rui Yun Pan ◽  
Hai Tao Ma
Keyword(s):  
Compressive Stress ◽  
High Temperature Oxidation ◽  
Oxidation Behavior ◽  
Oxide Scales ◽  
External Scale ◽  
X Ray Diffraction ◽  
Temperature Oxidation ◽  
X Ray ◽  
High Temperature Oxidation Behavior ◽  
Kinetics Of

The oxidation behavior of Fe-20Ni alloy under compressive stress in air was studied at 800, 900 °C. The results examined by using scanning electron microscope (SEM) and X-ray diffraction (XRD) indicates that the oxide scales were consisted of an external scale and a subscale which has an intragranular scale (above 5 h at 800 °C and 900 °C) and an intergranular scale. Compared with the unstressed specimen, the growth kinetics of external scale was accelerated by an applied compressive stress. Besides, the compressive stress induced an increase in the growths of intragranular scale and intergranular scale formed on the specimens oxidized at 900 °C. However, the effect of compressive stress on the growth of intergranular scale and intragranular scale was not obvious in the case of 800°C. In addition, cracks developed in the subscale for the specimens oxidized under 2.5 MPa compressive stress when the oxidation time exceeded 20 h.

Yttrium Implantation and Manganese Addition Element Effects on the High Temperature Oxidation Resistance of a Model Steel

2008 ◽  
Vol 595-598 ◽  
pp. 897-905
Author(s):  
Eric Caudron ◽  
Régis Cueff ◽  
Christophe Issartel ◽  
N. Karimi ◽  
Frédéric Riffard ◽  
...  
Keyword(s):  
Oxidation Resistance ◽  
High Temperatures ◽  
Mixed Oxides ◽  
Rutherford Backscattering Spectrometry ◽  
High Energy ◽  
X Ray Diffraction ◽  
Temperature Oxidation ◽  
X Ray ◽  
Steel Oxidation ◽  
Yttrium Implantation

Manganese addition and subsequent yttrium implantation effects on extra low carbon steel were studied by Rutherford Backscattering Spectrometry (RBS), Reflection High Energy Electron Diffraction (RHEED), X-ray Diffraction (XRD) and Glancing Angle X-ray Diffraction (GAXRD). Thermogravimetry and in situ X-Ray Diffraction at 700°C and PO2=0.04 Pa for 24h were used to determine the manganese alloying addition and subsequent yttrium implantation effects on reference steel oxidation resistance at high temperatures. This study clearly shows the combined effect of manganese alloying addition and subsequent yttrium implantation which promotes the formation of several yttrium mixed oxides seem to be responsible for the improved reference steel oxidation resistance at high temperatures.

scholarly journals Effect of Re and Tm-site on morphology structure and optical band gap of ReTmO3 (Re: La, Ce, Nd, Gd, Dy, Y and Tm: Fe, Cr) prepared by sol-gel method

2018 ◽  
Vol 64 (4) ◽  
pp. 381
Author(s):  
Muhammad Tufiq Jamil ◽  
Javed Ahmad ◽  
Syed Hamad Bukhari ◽  
Murtaza Saleem
Keyword(s):  
Band Gap ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
Orthorhombic Crystal ◽  
X Ray ◽  
Average Grain Size ◽  
Auto Combustion ◽  
Uv Visible

Rare earth nano sized pollycrystalline orthoferrites and orthocromites ReT mO3 (Re = La, Nd, Gd, Dy, Y and T m = Fe, Cr) have been synthesized by sol-gel auto combustion citrate method. The samples have been characterized by means of X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX), and UV-visible spectroscopy. The samples are single phase as confirmed by XRD analysis and correspond to the orthorhombic crystal symmetry with space group pbnm. Debye Scherer formula and Williamson Hall analysis have been used to calculate the average grain size which is consistent with that of determined from SEM analysis and varied between 25-75 nm. The elemental compositions of all samples have been checked by EDX analysis. Different crystallographic parameters are calculated with strong structural correlation among Re and Tm sites. The optical energy band gap has been calculated by using Tauc relation estimated to be in the range of 1.77 - 1.87 eV and 2.77 - 3.14 eV, for ReFeO3 and ReCrO3, respectively.

Hierarchical Nanostructured ZnO-CuO Nanocomposite and its Photocatalytic Activity

2015 ◽  
Vol 35 ◽  
pp. 21-26 ◽  
Author(s):  
Susmita Das ◽  
Vimal Chandra Srivastava
Keyword(s):  
Photocatalytic Activity ◽  
Pure Copper ◽  
Ultra Violet ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ultra Violet Radiation ◽  
One Step ◽  
Uv Visible

Metal oxide nanocomposite (ZnO-CuO) was successfully synthesized by one step homogeneous coprecipitation method and further characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron micrograph (SEM), X-ray diffraction analysis (XRD) and UV-visible diffuse reflectance spectra. XRD analysis exhibited presence of pure copper oxide and zinc oxide within the nanocomposite. SEM analysis indicated that the ZnO-CuO nanocomposite was consisted of flower shaped ZnO along with leaf shaped CuO. Photocatalytic activity of nanocomposite was evaluated in terms of degradation of methylene blue (MB) dye solution under ultra-violet radiation. Results showed that the photocatalytic efficiency of ZnO-CuO nanocomposite was higher than its individual pure oxides (ZnO or CuO).

Wear Behavior of TiB2/GNPs and B4C/GNPs Reinforced AA6061 Matrix Composites

2021 ◽  
Vol 143 (11) ◽  
Author(s):  
Safa Polat ◽  
Yavuz Sun ◽  
Engin C¸evik
Keyword(s):  
Wear Behavior ◽  
Sem Analysis ◽  
Matrix Composites ◽  
X Ray Diffraction ◽  
Pressure Infiltration ◽  
X Ray ◽  
Wear Rates ◽  
Graphene Nanoparticles ◽  
Infiltration Method ◽  
Scanning Electron

Abstract In this study, it was aimed to investigate the effects of reinforcements used for improving the thermal properties of AA6061 alloy on wear resistance. For this purpose, AA6061 matrix composites were produced by pressure infiltration method using ceramic microparticles (TiB2 and B4C) and graphene nanoparticles (GNPs). The produced composites were first characterized by porosity measurement, X-ray diffraction (XRD), and scanning electron microscopy (SEM) analysis. Then, the wear behavior was examined under three different loads (20–40–60 N) with the reciprocating ball on the flat method in a dry environment. Specific wear-rates were calculated according to the Archard principle by measuring the depth and width of the traces after tests with a profilometer. Wearing mechanisms were determined with the help of optical and microstructure images. According to the obtained results, it was found that B4C + GNPs reinforced samples were more resistant to abrasion at low loads, but TiB2 + GNPs reinforced samples were higher at higher loads.

Sign in / Sign up

Export Citation Format

Share Document