scholarly journals Adjustment of drilling slurry density during transportation by Platform Supply Vessels

2021 ◽  
Vol 27 (1) ◽  
pp. 52-62
Author(s):  
Сергей Анатольевич Карьянский ◽  
◽  
Денис Николаевич Марьянов ◽  
Keyword(s):  
Energy Consumption ◽  
Relative Density ◽  
Drilling Fluid ◽  
Direct Approach ◽  
Density Stratification ◽  
Equal Size ◽  
Fluid Density ◽  
Oil Drilling ◽  
Density Measurements ◽  
A Value

Annotation – The issues of maintaining the drilling fluid density during its transportation from shore to the oil drilling platform by the Platform Supply Vessels were considered. The research was carried out on the vessel of 5650 deadweight tons, which made 2 ... 2.5 day voyages from port to drilling platform with possible waiting for direct approach to the platform for 1 ... 1.5 days. The drilling fluid was transported in four tanks of equal-size, arranged in pairs on each side of the vessel. It was found that during this period of time there is a latent stratification of drilling fluid along the depth of cargo tank, causing stratification of its density. The density of the drilling fluid was measured at depths corresponding to 10, 50 and 90 % of the total tank depth. The drilling fluid density stratification is defined as the relative density change in the upper (at 10 % depth) and lower (at 90 % depth) parts of the cargo tank. The hydrometer was used to measure density, allowing measurements in the range of 650 ... 1630 kg/m3 with an accuracy of 1 kg/m3 while controlling the temperature. Density measurements were taken at 6-hour intervals. It has been experimentally proved that during the 48-hour transportation of the drilling fluid with the density of 1295 kg/m3, the density value at the indicated depths is 1163 and 1524 kg/m3 respectively, while the density stratification reaches 31 %. It is offered to prevent the density stratification by creating a forced X-shaped circulation of the drilling fluid between cargo tanks which stand side by side. It is offered to regulate and maintain automatically the drilling fluid density in the range of 2 ... 7 % by using programmable controllers. When the density stratification reaches 7 %, the controller switches on the circulation pumps and circulates the drilling fluid between tanks which stand side by side. This increases the drilling fluid uniformity and helps to reduce the density stratification along the depth of the cargo tank. The process of additional circulation of the drilling fluid is rationally ensured until the density stratification reaches a value of 2 %. Fulfilment of the above-mentioned conditions will ensure that the drilling fluid maintains its operational properties and the energy consumption associated with the additional operation of the circulation pumps is minimised.

scholarly journals Application of Thermal Resistant Gemini Surfactants in Highly Thixotropic Water-in-oil Drilling Fluid System

2019 ◽  
Vol 17 (1) ◽  
pp. 1435-1441
Author(s):  
Yonggui Liu ◽  
Yang Zhang ◽  
Jing Yan ◽  
Tao Song ◽  
Yongjun Xu
Keyword(s):  
Gemini Surfactants ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Excellent Thermal Stability ◽  
Oil Drilling ◽  
Low Viscosity ◽  
Emulsion Drops ◽  
Oil Emulsions ◽  
Building Capability ◽  
Liquid Precipitation

AbstractTraditional water-in-oil drilling fluids are limited by their shear thinning behavior. In this article, we propose the synthesis of a thermal resistant quaternary ammonium salt gemini surfactant DQGE-I. This surfactant was synthesized using monomers such as N,N-dimethyl-1,3-propanediamine, organic acids and epichlorohydrin, as well as blocking groups such as N-vinylpyrrolidone (NVP). The prepared surfactant exhibited various advantages over traditional surfactants, including excellent thermal stability, good emulsifying and wetting capability. The use of these surfactants was shown to improve the compactness of emulsifier molecules at the oil/water interface, as well as the overall emulsificaiton effect. Laboratory studies revealed that water-in-oil emulsions prepared using DQGE-I showed high emulsion breaking voltage, low liquid precipitation and small and uniformly distributed emulsion drops. Highly thixotropic water-in-oil drilling fluids based on DQGE-I showed low viscosity, high shear rate and thermal tolerance up to 260oC. Additionally, the proposed fluid was applied in 16 wells (including WS1-H2, GS3 and XS1-H8) in the Daqing Oilfield. Testing showed that DQGE-1 exhibited excellent rheological behavior and wall-building capability. The emulsion breaking voltage exceeded 1500 V, and the yield point/ plastic viscosity ratio exceeded 0.4. The use of this surfactant can help to solve problems such as high formation temperature and poor well wall stability.

A Novel Method to Determine the Drilling Fluid Density for Gypsum-Salt Layer

2021 ◽  
Author(s):  
Jitong Liu ◽  
Wanjun Li ◽  
Haiqiu Zhou ◽  
Yixin Gu ◽  
Fuhua Jiang ◽  
...  
Keyword(s):  
Drilling Fluid ◽  
In Situ Stress ◽  
Wellbore Stability ◽  
Shrinkage Rate ◽  
Fluid Density ◽  
Salt Layer ◽  
Rock Creep ◽  
Key Factor ◽  
Well Abandonment

Abstract The reservoir underneath the salt bed usually has high formation pressure and large production rate. However, downhole complexities such as wellbore shrinkage, stuck pipe, casing deformation and brine crystallization prone to occur in the drilling and completion of the salt bed. The drilling safety is affected and may lead to the failure of drilling to the target reservoir. The drilling fluid density is the key factor to maintain the salt bed’s wellbore stability. The in-situ stress of the composite salt bed (gypsum-salt -gypsum-salt-gypsum) is usually uneven distributed. Creep deformation and wellbore shrinkage affect each other within layers. The wellbore stability is difficult to maintain. Limited theorical reference existed for drilling fluid density selection to mitigate the borehole shrinkage in the composite gypsum-salt layers. This paper established a composite gypsum-salt model based on the rock mechanism and experiments, and a safe-drilling density selection layout is formed to solve the borehole shrinkage problem. This study provides fundamental basis for drilling fluid density selection for gypsum-salt layers. The experiment results show that, with the same drilling fluid density, the borehole shrinkage rate of the minimum horizontal in-situ stress azimuth is higher than that of the maximum horizontal in-situ stress azimuth. However, the borehole shrinkage rate of the gypsum layer is higher than salt layer. The hydration expansion of the gypsum is the dominant reason for the shrinkage of the composite salt-gypsum layer. In order to mitigate the borehole diameter reduction, the drilling fluid density is determined that can lower the creep rate less than 0.001, as a result, the borehole shrinkage of salt-gypsum layer is slowed. At the same time, it is necessary to improve the salinity, filter loss and plugging ability of the drilling fluid to inhibit the creep of the soft shale formation. The research results provide technical support for the safe drilling of composite salt-gypsum layers. This achievement has been applied to 135 wells in the Amu Darya, which completely solved the of wellbore shrinkage problem caused by salt rock creep. Complexities such as stuck string and well abandonment due to high-pressure brine crystallization are eliminated. The drilling cycle is shortened by 21% and the drilling costs is reduced by 15%.

Der energieflexible und effiziente Energiewertstrom/The efficient and flexible energy value stream

2015 ◽  
Vol 105 (05) ◽  
pp. 313-318
Author(s):  
F. Feder ◽  
K. Erlach ◽  
F. Hosak ◽  
H. Lepple
Keyword(s):  
Energy Consumption ◽  
Low Energy ◽  
Energy Usage ◽  
Energy Value ◽  
Value Stream ◽  
Building Technology ◽  
A Value ◽  
Energy Flows ◽  
Low Energy Consumption ◽  
And Control

Die wachsende Volatilität im deutschen Energiesektor bietet jenen Unternehmen zukünftig einen Wettbewerbsvorteil, die ihren Energieverbrauch kontinuierlich senken und flexibel anpassen können. Als Werkzeug dafür wurde die Energiewertstrom-Methode um weitere Energieflüsse aus der Gebäude- und Versorgungstechnik sowie um Aspekte der Energieflexibilität erweitert. Dies erlaubt die Gestaltung eines energiekostenoptimalen Wertstroms.   In the light of the increasing volatility in the German energy sector, companies that are able to constantly reduce and control their energy consumption will gain a competitive advantage. Therefore, the Energy Value Stream Method has been extended by adding further energy flows in building technology as well as aspects of flexible energy usage. This enables the design of a value stream that results in low energy consumption and costs.

scholarly journals Discussion: Accuracy of relative density measurements

Géotechnique ◽  
1973 ◽  
Vol 23 (2) ◽  
pp. 301-303
Author(s):  
S. Serota ◽  
G. Lowther
Keyword(s):  
Relative Density ◽  
Density Measurements

Density and Drag Reduction With Hollow Glass Additives

2014 ◽  
Author(s):  
Bahri Kutlu ◽  
Evren M. Ozbayoglu ◽  
Stefan Z. Miska ◽  
Nicholas Takach ◽  
Mengjiao Yu ◽  
...  
Keyword(s):  
Drag Reduction ◽  
Rheological Behavior ◽  
Drilling Fluid ◽  
Hydraulic Drag ◽  
Effect Of Temperature ◽  
Survival Ratio ◽  
Fluid Density ◽  
Hollow Glass ◽  
Glass Spheres ◽  
Reduction Effect

This study concentrates on the use of materials known as hollow glass spheres, also known as glass bubbles, to reduce the drilling fluid density below the base fluid density without introducing a compressible phase to the wellbore. Four types of lightweight glass spheres with different physical properties were tested for their impact on rheological behavior, density reduction effect, survival ratio at elevated pressures and hydraulic drag reduction effect when mixed with water based fluids. A Fann75 HPHT viscometer and a flow loop were used for the experiments. Results show that glass spheres successfully reduce the density of the base drilling fluid while maintaining an average of 0.93 survival ratio, the rheological behavior of the tested fluids at elevated concentrations of glass bubbles is similar to the rheological behavior of conventional drilling fluids and hydraulic drag reduction is present up to certain concentrations. All results were integrated into hydraulics calculations for a wellbore scenario that accounts for the effect of temperature and pressure on rheological properties, as well as the effect of glass bubble concentration on mud temperature distribution along the wellbore. The effect of drag reduction was also considered in the calculations.

scholarly journals Study on Method of Determining the Safe Operation Window of Drilling Fluid Density with Credibility in Deep Igneous Rock Strata

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Chao Han ◽  
Zhichuan Guan ◽  
Chuanbin Xu ◽  
Fuhui Lai ◽  
Pengfei Li
Keyword(s):  
Igneous Rock ◽  
Drilling Fluid ◽  
Prediction Method ◽  
Large Error ◽  
Fluid Density ◽  
Safe Operation ◽  
Collapse Pressure ◽  
Modified Method ◽  
Fracture Pressure ◽  
Rock Strata

It is difficult to determine the safe operation window of drilling fluid density (SOWDFD) for deep igneous rock strata. Although the formation three-pressure (pore pressure, collapse pressure, and fracture pressure) prediction method with credibility improves the accuracy of formation three-pressure prediction, it still has a large error for deep igneous strata. To solve this problem, a modified method of the SOWDFD in deep igneous rock strata is proposed based on the leakage statistics of adjacent wells. This method is based on the establishment of the SOWDFD with credibility. Through statistical analysis of drilling fluid density of igneous rock leaky formation group in adjacent wells, the fracture leakage law of the formation is revealed and the upper limit of leak-off pressure containing probability information is obtained. Finally, the modified SOWDFD with credibility for deep igneous rock strata is formed. In this work, the proposed method was used to compute the SOWDFD with credibility of SHB well in Xinjiang, China. Results show that the modified density window is consistent with the field drilling conditions and can reflect the narrow density window in the Permian and lower igneous strata. Combined with the formation three-pressure prediction method with credibility and the actual leakage law of adjacent wells, it can effectively improve the prediction accuracy of the SOWDFD for deep igneous rock strata. The findings of the study can help in better understanding of the complex downhole geological environment in deep igneous rock strata and making reasonable drilling design scheme.

Sign in / Sign up

Export Citation Format

Share Document