scholarly journals Interaction of Aqueous Cu2+ Ions with Granules of Crushed Concrete

2019 ◽  
Vol 20 (1) ◽  
pp. 31-38 ◽  
Author(s):  
Alyaa F. Ali ◽  
Ziad T. Abd Ali
Keyword(s):  
Aqueous Solution ◽  
Copper Ions ◽  
Synthetic Wastewater ◽  
Isotherm Models ◽  
Batch Experiments ◽  
Demolition Waste ◽  
Particle Size Range ◽  
Sorption Data ◽  
Surface Precipitation ◽  
Crushed Concrete

The sorption of Cu2+ ions from synthetic wastewater using crushed concrete demolition waste (CCDW) which collected from a demolition site was investigated in a batch sorption system. Factors influencing on sorption process such as shaking time (0-300min), the initial concentration of contaminant (100-750mg/L), shaking speed (0-250 rpm), and adsorbent dosage (0.05-3 g/ml) have been studied. Batch experiments confirmed that the best values of these parameters were (180 min, 100 mg/l, 250 rpm, 0.7 g CCDW/100 ml) respectively where the achieved removal efficiency is equal to 100%. Sorption data were described using four isotherm models (Langmuir, Freundlich, Redlich-Peterson, and Radke-Prausnitz). Results proved that the pure adsorption and precipitation are the main mechanisms for removal of copper ions from aqueous solution onto CCDW and sorption data can be represented by Langmuir and Radke-Prausnitz model. The copper ion was successfully removed from aqueous solution during batch experiments using CCDW in the particle size range 2–1 mm. Scanning electron microscopy detected that the removal of Cu2+ was found to arise from surface precipitation.

scholarly journals Removal of lead ions from wastewater using crushed concrete demolition waste

2019 ◽  
Vol 26 (4) ◽  
pp. 22-29
Author(s):  
Alyaa F. Ali ◽  
Ziad T. Abd Ali
Keyword(s):  
Aqueous Solution ◽  
Lead Ions ◽  
Synthetic Wastewater ◽  
Cement Matrix ◽  
Lead Ion ◽  
Batch Experiments ◽  
Demolition Waste ◽  
Sorption Data ◽  
Principal Mechanism ◽  
Crushed Concrete

The sorption of Pb2+ ions from synthetic wastewater using crushed concrete demolition waste (CCDW) which collected from a demolition site was investigated in a batch sorption system. Factors influencing on sorption process such as shaking time (0-300min), initial concentration of contaminant (100-750mg/L), shaking speed (0-250 rpm), and adsorbent dosage (0.05-3 g/ml) have been studied. Batch experiments confirmed that the best values of these parameters were (180 min, 100 mg/l, 200 rpm, 0.3 g CCDW/100 ml) respectively where the achieved removal efficiency is equal to 100%. Sorption data were described using four isotherm models (Langmuir, Freundlich, Redlich-Peterson, and Radke-Prausnitz). Results proved that the pure adsorption and precipitation are the main mechanisms for removal of lead ions from aqueous solution onto CCDW and sorption data can be represented by Langmuir model. The lead ion was successfully removed from aqueous solution during batch experiments using (CCDW) in the particle size range 2–1 mm. The principal mechanism of uptake of Pb2+ was found to be by diffusion into the cement matrix and this was detected by Scanning electron microscopy.

scholarly journals Fly Ash Coated with Magnetic Materials: Improved Adsorbent for Cu (II) Removal from Wastewater

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 63
Author(s):  
Maria Harja ◽  
Gabriela Buema ◽  
Nicoleta Lupu ◽  
Horia Chiriac ◽  
Dumitru Daniel Herea ◽  
...  
Keyword(s):  
Fly Ash ◽  
Adsorption Capacity ◽  
Copper Ions ◽  
Synthetic Wastewater ◽  
Bet Surface Area ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Copper Adsorption ◽  
X Ray

Fly ash/magnetite material was used for the adsorption of copper ions from synthetic wastewater. The obtained material was characterized by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), X-ray diffractometer (XRD), Fourier transform infrared spectroscopy (FTIR), Brunauer–Emmett–Teller (BET) surface area, and vibrating sample magnetometer (VSM). Batch adsorption experiments were employed in order to investigate the effects of adsorbent dose, initial Cu (II) concentration and contact time over adsorption efficiency. The experimental isotherms were modeled using Langmuir (four types of its linearization), Freundlich, Temkin, and Harkins–Jura isotherm models. The fits of the results are estimated according to the Langmuir isotherm, with a maximum adsorption capacity of 17.39 mg/g. The pseudo-second-order model was able to describe kinetic results. The data obtained throughout the study prove that this novel material represents a potential low-cost adsorbent for copper adsorption with improved adsorption capacity and magnetic separation capability compared with raw fly ash.

scholarly journals Sorption of Cd2+ and Pb2+ on Aragonite Synthesized from Eggshell

2020 ◽  
Vol 12 (3) ◽  
pp. 1174 ◽  
Author(s):  
Lulit Habte ◽  
Natnael Shiferaw ◽  
Mohd Danish Khan ◽  
Thenepalli Thriveni ◽  
Ji Whan Ahn
Keyword(s):  
Experimental Data ◽  
Synthetic Wastewater ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Solution Ph ◽  
Surface Precipitation ◽  
Initial Ph ◽  
Order Kinetic Model ◽  
High Sorption ◽  
Pseudo Second Order

In the present work, waste eggshells were used as a precursor for the synthesis of aragonite crystals through the wet carbonation method. Cadmium (Cd2+) and lead (Pb2+) were removed by the synthesized aragonite from synthetic wastewater. The influence of initial solution pH, contact time, Cd2+ and Pb2+ concentration, and sorbent dosage were evaluated. The major sorption was observed in the first 100 mins and 360 mins for Pb2+and Cd2+ respectively reaching sorption equilibrium at 720 mins (12 hr). The sorption capacity toward Pb2+ was much higher than toward Cd2+. Both heavy metals displayed high sorption capacities at initial pH 6. The pseudo-second-order kinetic model fits well with the experimental data with a higher correlation coefficient R2. Two isotherm models were also evaluated for the best fit with the experimental data obtained. Langmuir isotherm best fits the sorption of the metals on aragonite synthesized from eggshells. X-ray diffraction (XRD) and Scanning electron microscopy (SEM) results of sorbent after sorption showed that the mechanism of sorption was dominated by surface precipitation. Therefore, aragonite crystals synthesized from waste eggshells can be a potential substitute source for the removal of Cd2+ and Pb2+ from contaminated water.

Experimental Investigation on Adsorptive Removal of Phenolic Compounds from Aqueous Solution by Cr-Bentonite

2010 ◽  
Vol 160-162 ◽  
pp. 163-170
Author(s):  
Hong Zheng ◽  
Yang Wang ◽  
Peng Liang ◽  
Hong Bin Qi
Keyword(s):  
Experimental Data ◽  
Aqueous Solution ◽  
Phenolic Compounds ◽  
Intraparticle Diffusion ◽  
Second Order ◽  
Synthetic Wastewater ◽  
Order Kinetic ◽  
Sorption Data ◽  
Adsorptive Removal ◽  
Pseudo Second Order

The ability of Cr-bentonite prepared using synthetic wastewater containing chromium was investigated for adsorptive removal of 4-aminophenol and 4-chlorophenol from aqueous solution in a batch system at 25 °C. The physic-chemical parameters including pH value of solution and contact time were studied. The experimental data were analyzed by the Langmuir, Freundlich and Temkin models of sorption. The equilibrium sorption data for 4-aminophenol and 4-chlorophenol were well fitted to Langmuir adsorption isotherm and the monolayer sorption capacity was found to be 26.53 and 23.81 mg/g at 25 °C, respectively. The sorption energy calculated from Dubinin-Redushkevich (D-R) isotherm are 8.31 and 8.20 kJ/mol for the uptake of 4-aminophenol and 4-chlorophenol respectively which indicates that both the sorption processes are chemical in nature. The kinetic data were analyzed using pseudo-first order, pseudo-second order kinetic equation and intraparticle diffusion model. The experimental data fit very well the pseudo-second order kinetic model. Intraparticle diffusion affects 4-aminophenol and 4-chlorophenol uptake. Sorption studies carried out using industrial wastewater samples containing phenolic compounds show that there is significant potential for Cr-bentonite as an adsorbent material for phenollic compounds removal from aqueous solutions.

scholarly journals Utilization of Sago Waste as an Adsorbent for the Removal of Cu(II) Ion from Aqueous Solution

2008 ◽  
Vol 5 (2) ◽  
pp. 233-242 ◽  
Author(s):  
P. Maheswari ◽  
N. Venilamani ◽  
S. Madhavakrishnan ◽  
P. S. Syed Shabudeen ◽  
R. Venckatesh ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Metal Ion ◽  
Chemical Properties ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Equilibrium Isotherm ◽  
Particle Size Range ◽  
Industry Waste ◽  
Sago Waste

The preparation of activated carbon (AC) from sago industry waste is a promising way to produce a useful adsorbent for Cu(II) removal, as well as dispose of sago industry waste. The AC was prepared using sago industry waste with H2SO4and (NH4)2S2O8and physico-chemical properties of AC were investigated. The specific surface area of the activated carbon was determined and its properties studied by scanning electron microscopy (SEM). Adsorptive removal of Cu(II) from aqueous solution onto AC prepared from sago industry waste has been studied under varying conditions of agitation time, metal ion concentration, adsorbent dose and pH to assess the kinetic and equilibrium parameters. Adsorption equilibrium was obtained in 60min for 20 to 50mg/L of Cu(II) concentrations. The Langmuir and Freundlich equilibrium isotherm models were found to provide an excellent fitting of the adsorption data. In Freundlich equilibrium isotherm, the RL values obtained were in the range of 0 to 1 (0.043 to 0.31) for Cu(II) concentration of 10 to 100mg/L, which indicates favorable adsorption of Cu(II) onto Sago waste carbon. The adsorption capacity of Cu(II) (Qo) obtained from the Langmuir equilibrium isotherm model was found to be 32.467 mg/g at pH 4 ± 0.2 for the particle size range of 125–250u. The percent removal increased with an increase in pH from 2 to 4. This adsorbent was found to be effective and economically attractive.

Élimination des ions Cu(II) d'une solution aqueuse par les micro-particules de la plante Carpobrotus edulis en système dynamiqueRemoval of Cu(II) ions from aqueous solution by micro-particles of dried Carpobrotus edulis plant in a column system

2011 ◽  
Vol 46 (3) ◽  
pp. 259-267 ◽  
Author(s):  
Mohamed Chiban ◽  
Fouad Sinan
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Adsorption Process ◽  
Copper Ions ◽  
Isotherm Models ◽  
Carpobrotus Edulis ◽  
Micro Particles ◽  
Column System ◽  
Adsorption Mode ◽  
Column Adsorption

This study reports on the removal of Cu(II) ions from an aqueous solution by adsorption onto dried Carpobrotus edulis plant in a column system. The effect of various process parameters, namely m/V ratio, contact time, initial Cu(II) concentration and pH was studied. The experimental data were analyzed using Freundlich and Langmuir isotherm models to determine the mechanistic parameters related to the adsorption process. The results showed that the adsorption of Cu(II) ions by dried C. edulis increases with the increase of contact time, adsorbent dose, pH and initial Cu(II) concentration in the solution. The maximum adsorption of Cu(II) is reached after one hour of contact time at initial copper concentrations ranging between 10 and 100 mg/L. The m/V ratio of 25 g/L was optimal to obtain a maximum adsorption of copper ions. The maximum adsorption percentage of C. edulis is equal to 94.4%. These results showed that the dried C. edulis plant could be considered as a potential adsorbent material for the removal of Cu(II) from wastewater, using a column adsorption mode.

scholarly journals Adsorption of copper (II) ions from aqueous solution using bottom ash of expired drugs incineration

2017 ◽  
Vol 36 (1-2) ◽  
pp. 114-129 ◽  
Author(s):  
Thouria Benzaoui ◽  
Ammar Selatnia ◽  
Djaafar Djabali
Keyword(s):  
Aqueous Solution ◽  
Copper Ions ◽  
Bottom Ash ◽  
Analytical Techniques ◽  
Isotherm Models ◽  
Homogeneous Surface ◽  
Adsorption Isotherm Models ◽  
Effects Of Ph ◽  
Best Fit ◽  
Mechanism Of Sorption

The use of bottom ash of expired drugs incineration for removal of Cu(II) ions from aqueous solution has been investigated. Analytical techniques have been employed to find characteristics of adsorbent materials. The removal of Cu(II) was conducted in batch system, and the effects of pH, adsorbent dosage, initial concentrations of copper ions, and contact time on adsorption efficiency were studied. Optimum adsorption was achieved at a pH 5 and equilibrium was established within 15 min of the process. The equilibrium adsorption data were analyzed using eight adsorption isotherm models: Langmuir, Freundlich, Temkin, Redlich–Peterson, Dubinin–Radushkevich, Toth, Harkin–Jura and Halsey isotherms. The energy value obtained by application of Dubinin–Radushkevich model was 2.593 kJ/mol indicating that physisorption was the dominant mechanism of sorption. The values of the correlation coefficient (R2) of the isotherms gave the best fit (>0.99) with the Langmuir, Toth, and Redlich–Peterson isotherms. The adsorption capacity (qm) from the Langmuir isotherm for Cu(II) was found as 13.335 mg/g. The equation constant n of Toth isotherm model is found to be close to 1 (0.945), confirming that the adsorbent studied presents homogeneous surface under conditions used. It is concluded that bottom ash of expired drugs incineration can be used as an effective adsorbent for removing Cu(II) from aqueous solution.

scholarly journals Two–three parameters isotherm modeling, kinetics with statistical validity, desorption and thermodynamic studies of adsorption of Cu(II) ions onto zerovalent iron nanoparticles

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Adewumi O. Dada ◽  
Folahan A. Adekola ◽  
Ezekiel O. Odebunmi ◽  
Adeniyi S. Ogunlaja ◽  
Olugbenga S. Bello
Keyword(s):  
Copper Ions ◽  
Statistical Error ◽  
Intraparticle Diffusion ◽  
Zerovalent Iron ◽  
Synthetic Wastewater ◽  
Bet Surface Area ◽  
Isotherm Models ◽  
Elemental Distribution ◽  
Operational Parameters ◽  
Thermodynamic Studies

AbstractAdsorption of problematic copper ions as one of the endocrine disruptive substances from aqueous solution onto nanoscale zerovalent iron (nZVI) was studied. The high pore size 186.9268 Å, pore diameter 240.753 Å, and BET surface area 20.8643 m2 g−1 and pH(pzc) enlisted nZVI as an efficient nano-adsorbent for treatment of heavy metals from synthetic wastewater. SEM and EDX revealed the morphology and elemental distribution before and after adsorption. 98.31% removal efficiency was achieved at optimum adsorption operational parameters. Of all the thirteen isotherm models, equilibrium data were well fitted to Langmuir. Kinetics and mechanism data across the concentrations from 10 to 200 mg L−1 were analyzed by ten models. PSO best described kinetics data as confirmed by various statistical error validity models. The intraparticle diffusion model described that the intraparticle diffusion was not the only rate-limiting step. The adsorption mechanism was diffusion governed established by Bangham and Boyd models. Feasible, spontaneous, endothermic, and degree of randomness were reveal by the thermodynamic studies. Better desorption index and efficiency were obtained using HCl suggesting multiple mechanism processes. The performance of ZVI suggested it has a great potential for effective removal of endocrine disruptive cationic contaminant from wastewater.

scholarly journals The biosorption potential of waste biomass young fruit walnuts for lead ions: Kinetic and equilibrium study

2016 ◽  
Vol 70 (3) ◽  
pp. 243-255
Author(s):  
Dragana Markovic ◽  
Danijela Bojic ◽  
Aleksandar Bojic ◽  
Goran Nikolic
Keyword(s):  
Aqueous Solution ◽  
Metal Ions ◽  
Metal Ion ◽  
Low Cost ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Waste Biomass ◽  
Sorption Data ◽  
Biosorption Capacity ◽  
Young Fruit

The biosorption potential of waste biomass young fruit walnuts (YFW) as a low-cost biosorbent, processed from liqueur industry, for Pb(II) ions from aqueous solution was explored. The structural features of the biosorbent were characterized by FTIR spectroscopy, which indicates the possibility that the different functional groups may be responsible for the binding of Pb(II) ions from aqueous solution. The effects of relevant parameters such as pH (2 - 6), contact time (0 - 120 min), biosorbent dosage (2 - 20 g), initial metal ion concentration (10 - 120 mg dm-3), at a temperature of 25(C with stirring (120 rpm) and a constant ionic strength of 0,02 mol dm-3 were evaluated in batch experiments. The sorption equilibrium of Pb(II) ion (when 84 % of metal ions were sorbed at an initial concentration of 15 mg dm-3) was achieved within the pH range 4 - 5 after 50 min. Kinetic data were best described by the pseudo-second order model. Removal efficiency of Pb(II) ion rapidly increased with increasing biosorbent dose from 2.0 to 8.0 g per dm-3 of sorbate. Optimal biosorbent dose was set to 6.0 g per dm3 of sorbate. An increase in the initial metal concentration increases the biosorption capacity. The sorption data of investigated metal ion are fitted to Langmuir, Freundlich and Temkin isotherm models. The equilibrium data were well fitted by the Langmuir isotherm model (R2 ? 0.990). The maximum monolayer biosorption capacity of waste biomass YFW for Pb(II) ion, at 25.0 ? 0.5?C and pH 4.5, was found to be 19.23 mgg-1. This available waste biomass is efficient in the uptake of Pb(II) ions from aqueous solution and could be used as a low-cost and an alternative biosorbent for the treatment of wastewater streams bearing these metal ions.

scholarly journals Kinetic and thermodynamic studies on the adsorption of Cu2+ ions from aqueous solution by using agricultural waste-derived biochars

2020 ◽  
Vol 20 (8) ◽  
pp. 3120-3140
Author(s):  
Nihan Kaya ◽  
Ferhat Arslan ◽  
Zeynep Yıldız Uzun ◽  
Selim Ceylan
Keyword(s):  
Aqueous Solution ◽  
Copper Ions ◽  
Agricultural Waste ◽  
Experimental Results ◽  
Walnut Shell ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Adsorption Parameters ◽  
Mixing Speed ◽  
Hazelnut Shell

Abstract In this study, it was aimed to investigate the adsorption properties of the biochars obtained by pyrolysis of hazelnut and walnut shells for removal of copper ions from aqueous solutions. The characterization of raw biomasses and also biochars were performed using TGA-DTG, FT-IR, BET, SEM, partial and elemental analysis techniques. The optimum conditions were determined by investigating the effect of adsorption parameters (initial concentration, temperature, adsorbent amount, pH, contact time and mixing speed) for efficient removal of copper ions from aqueous solution by batch adsorption experiments carried out under different conditions. The highest adsorption efficiencies were recorded as 82 and 86% respectively for hazelnut and walnut shell biochars at pH 4, Co = 15 ppm, adsorbent dosage = 3 g/L and mixing speed = 600 rpm. Experimental results showed that the adsorption efficiency for copper ions increased with the increase of temperature (T = 45 °C) in studies only using biochar obtained from hazelnut shell. While the time of equilibrium in the aqueous solution containing copper ions was determined to be 75 min for walnut shell char, this duration was 30 min for hazelnut shell char. The experimental results were investigated in terms of Langmuir, Freundlich and Temkin isotherm models. Together with the calculated thermodynamic parameters, the adsorption mechanism was explained. In order to determine the kinetic model of the adsorption process, the experimental data were applied to pseudo first-order, pseudo second-order and intra-particle diffusion models, and the model constants were investigated.

Sign in / Sign up

Export Citation Format

Share Document