scholarly journals A biomechanical invesitgation of the surface stress of a synthetic femur using infrated thermography validated by strain gauge measurements

2021 ◽  
Author(s):  
Suraj Shah
Keyword(s):  
Strain Gauge ◽  
Surface Stress ◽  
Pearson Correlation ◽  
Three Dimensional ◽  
The Elderly ◽  
Fracture Repair ◽  
Strain Gauges ◽  
North American Population ◽  
Ir Thermography ◽  
Strain Gauge Measurements

As the North American population ages, there will be a massive increase in musculoskeletal impairments because these problems are most common in the elderly. A very common condition is osteoporosis, which can result in fractures. Therefore, the need for improved orthopaedic fracture repair implants is vital. Currently, the two main approaches in studying orthopaedic implants are strain gauge measurements and finite element modelling. This study introduces and validates a relatively new, non-destructive approach in analysing stress patterns in a biomechanics application. Lock-in infrared (IR) thermography calibrated with strain gauges was used to investigate the stress and strain patterns of a synthetic femur under dynamic loading. The femur was instrumented with strain gauges and tested using axial average forces of 1500N, 1800N, and 2100N at an adduction angle of 7 degrees to simulate the single-legged stance phase of walking. Three dimensional surface stress maps were obtained using an IR thermography versus strain gauge data with a Pearson correlation of R² = 0.99 and a slope ranging from 0.99 to 1.08, based on thermoelastic coefficient (Km) ranging from 1.067 x 10⁻⁵/MPa to 1.16 x 10⁻⁵/MPa, for the line of best fit. IR thermography detected bone peak stresses on the superior-posterior side of the femoral neck of 91.2MPa (at 1500 N), 96.0Mpa (at 1800 N), and 103.5MPa (at 2100 N). There was strong correlation between IR measured stresses and force along the anterior (R² = 0.87 to 0.99), posterior (R² = 0.81 to 0.99) and lateral (R² = 0.89 to 0.99) surface. This is the first study to provide an experimentally validated three dimensional stress map of a synthetic femur using IR thermography.

scholarly journals A biomechanical invesitgation of the surface stress of a synthetic femur using infrated thermography validated by strain gauge measurements

2021 ◽  
Author(s):  
Suraj Shah
Keyword(s):  
Strain Gauge ◽  
Surface Stress ◽  
Pearson Correlation ◽  
Three Dimensional ◽  
The Elderly ◽  
Fracture Repair ◽  
Strain Gauges ◽  
North American Population ◽  
Ir Thermography ◽  
Strain Gauge Measurements

As the North American population ages, there will be a massive increase in musculoskeletal impairments because these problems are most common in the elderly. A very common condition is osteoporosis, which can result in fractures. Therefore, the need for improved orthopaedic fracture repair implants is vital. Currently, the two main approaches in studying orthopaedic implants are strain gauge measurements and finite element modelling. This study introduces and validates a relatively new, non-destructive approach in analysing stress patterns in a biomechanics application. Lock-in infrared (IR) thermography calibrated with strain gauges was used to investigate the stress and strain patterns of a synthetic femur under dynamic loading. The femur was instrumented with strain gauges and tested using axial average forces of 1500N, 1800N, and 2100N at an adduction angle of 7 degrees to simulate the single-legged stance phase of walking. Three dimensional surface stress maps were obtained using an IR thermography versus strain gauge data with a Pearson correlation of R² = 0.99 and a slope ranging from 0.99 to 1.08, based on thermoelastic coefficient (Km) ranging from 1.067 x 10⁻⁵/MPa to 1.16 x 10⁻⁵/MPa, for the line of best fit. IR thermography detected bone peak stresses on the superior-posterior side of the femoral neck of 91.2MPa (at 1500 N), 96.0Mpa (at 1800 N), and 103.5MPa (at 2100 N). There was strong correlation between IR measured stresses and force along the anterior (R² = 0.87 to 0.99), posterior (R² = 0.81 to 0.99) and lateral (R² = 0.89 to 0.99) surface. This is the first study to provide an experimentally validated three dimensional stress map of a synthetic femur using IR thermography.

A Preliminary Biomechanical Assessment of a Polymer Composite Hip Implant Using an Infrared Thermography Technique Validated by Strain Gage Measurements

2011 ◽  
Vol 133 (7) ◽  
Author(s):  
Habiba Bougherara ◽  
Ehsan Rahim ◽  
Suraj Shah ◽  
Anton Dubov ◽  
Emil H. Schemitsch ◽  
...  
Keyword(s):  
Strain Gage ◽  
Pearson Correlation ◽  
Three Dimensional ◽  
Neck Region ◽  
Peak Stress ◽  
Ir Thermography ◽  
Perfect Agreement ◽  
Hip Implant ◽  
Medial Side ◽  
Lock In

With the resurgence of composite materials in orthopaedic applications, a rigorous assessment of stress is needed to predict any failure of bone-implant systems. For current biomechanics research, strain gage measurements are employed to experimentally validate finite element models, which then characterize stress in the bone and implant. Our preliminary study experimentally validates a relatively new nondestructive testing technique for orthopaedic implants. Lock-in infrared (IR) thermography validated with strain gage measurements was used to investigate the stress and strain patterns in a novel composite hip implant made of carbon fiber reinforced polyamide 12 (CF/PA12). The hip implant was instrumented with strain gages and mechanically tested using average axial cyclic forces of 840 N, 1500 N, and 2100 N with the implant at an adduction angle of 15 deg to simulate the single-legged stance phase of walking gait. Three-dimensional surface stress maps were also obtained using an IR thermography camera. Results showed almost perfect agreement of IR thermography versus strain gage data with a Pearson correlation of R2 = 0.96 and a slope = 1.01 for the line of best fit. IR thermography detected hip implant peak stresses on the inferior-medial side just distal to the neck region of 31.14 MPa (at 840 N), 72.16 MPa (at 1500 N), and 119.86 MPa (at 2100 N). There was strong correlation between IR thermography-measured stresses and force application level at key locations on the implant along the medial (R2 = 0.99) and lateral (R2 = 0.83 to 0.99) surface, as well as at the peak stress point (R2 = 0.81 to 0.97). This is the first study to experimentally validate and demonstrate the use of lock-in IR thermography to obtain three-dimensional stress fields of an orthopaedic device manufactured from a composite material.

Propagation and Reflection of Plane Waves in a Rotating Magneto-Elastic Fibre-Reinforced Semi Space with Surface Stress

2020 ◽  
Vol 22 (4) ◽  
pp. 939-958
Author(s):  
Indrajit Roy ◽  
D. P. Acharya ◽  
Sourav Acharya
Keyword(s):  
Surface Stress ◽  
Incident Angle ◽  
Plane Waves ◽  
Three Dimensional ◽  
Elastic Fibre ◽  
Amplitude Ratios ◽  
Governing Equations ◽  
Rotation Surface ◽  
Wave Velocities ◽  
Magnetic Field Rotation

AbstractThe present paper investigates the propagation of quasi longitudinal (qLD) and quasi transverse (qTD) waves in a magneto elastic fibre-reinforced rotating semi-infinite medium. Reflections of waves from the flat boundary with surface stress have been studied in details. The governing equations have been used to obtain the polynomial characteristic equation from which qLD and qTD wave velocities are found. It is observed that both the wave velocities depend upon the incident angle. After imposing the appropriate boundary conditions including surface stress the resultant amplitude ratios for the total displacements have been obtained. Numerically simulated results have been depicted graphically by displaying two and three dimensional graphs to highlight the influence of magnetic field, rotation, surface stress and fibre-reinforcing nature of the material medium on the propagation and reflection of plane waves.

scholarly journals The patellofemoral morphology and the normal predicted value of tibial tuberosity-trochlear groove distance in the Chinese population

2021 ◽  
Vol 22 (1) ◽  
Author(s):  
Zhe Li ◽  
Guanzhi Liu ◽  
Run Tian ◽  
Ning Kong ◽  
Yue Li ◽  
...  
Keyword(s):  
Individual Differences ◽  
Chinese Population ◽  
Pearson Correlation ◽  
Three Dimensional ◽  
Correlation Coefficients ◽  
Tibial Tuberosity ◽  
Trochlear Groove ◽  
Lasso Regression ◽  
Cross Sectional ◽  
Anterior Posterior

Abstract Background Our objective was to obtain normal patellofemoral measurements to analyse sex and individual differences. In addition, the absolute values and indices of tibial tuberosity-trochlear groove (TT-TG) distances are still controversial in clinical application. A better method to enable precise prediction is still needed. Methods Seventy-eight knees of 78 participants without knee pathologies were included in this cross-sectional study. A CT scan was conducted for all participants and three-dimensional knee models were constructed using Mimics and SolidWorks software. We measured and analysed 19 parameters including the TT-TG distance and dimensions and shapes of the patella, femur, tibia, and trochlea. LASSO regression was used to predict the normal TT-TG distances. Results The dimensional parameters, TT-TG distance, and femoral aspect ratio of the men were significantly larger than those of women (all p values < 0.05). However, after controlling for the bias from age, height, and weight, there were no significant differences in TT-TG distances and anterior-posterior dimensions between the sexes (all p values > 0.05). The Pearson correlation coefficients between the anterior femoral offset and other indexes were consistently below 0.3, indicating no relationship or a weak relationship. Similar results were observed for the sulcus angle and the Wiberg index. Using LASSO regression, we obtained four parameters to predict the TT-TG distance (R2 = 0.5612, p < 0.01) to achieve the optimal accuracy and convenience. Conclusions Normative data of patellofemoral morphology were provided for the Chinese population. The anterior-posterior dimensions of the women were thicker than those of men for the same medial-lateral dimensions. More attention should be paid to not only sex differences but also individual differences, especially the anterior condyle and trochlea. In addition, this study provided a new method to predict TT-TG distances accurately.

scholarly journals Origin and Application of the Twinned Calcite Strain Gauge

Geosciences ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 296
Author(s):  
Richard H. Groshong
Keyword(s):  
Stress Analysis ◽  
Strain Gauge ◽  
Strain Tensor ◽  
Three Dimensional ◽  
Constant Strain Rate ◽  
Axis Orientation ◽  
Order Of Magnitude ◽  
Rate Experiment ◽  
Strain Axis ◽  
Expected Values

This paper is a personal account of the origin and development of the twinned-calcite strain gauge, its experimental verification, and its relationship to stress analysis. The method allows the calculation of the three-dimensional deviatoric strain tensor based on five or more twin sets. A minimum of about 25 twin sets should provide a reasonably accurate result for the magnitude and orientation of the strain tensor. The opposite-signed strain axis orientation is the most accurately located. Where one strain axis is appreciably different from the other two, that axis is generally within about 10° of the correct value. Experiments confirm a magnitude accuracy of 1% strain over the range of 1–12% axial shortening and that samples with more than 40% negative expected values imply multiple or rotational deformations. If two deformations are at a high angle to one another, the strain calculated from the positive and negative expected values separately provides a good estimate of both deformations. Most stress analysis techniques do not provide useful magnitudes, although most provide a good estimate of the principal strain axis directions. Stress analysis based on the number of twin sets per grain provides a better than order-of-magnitude approximation to the differential stress magnitude in a constant strain rate experiment.

Optimum Strain Gauge Application to Bladed Assemblies

2002 ◽  
Author(s):  
J. Szwedowicz ◽  
S. M. Senn ◽  
R. S. Abhari
Keyword(s):  
Strain Gauge ◽  
Element Model ◽  
Strain Gauges ◽  
Structural Components ◽  
Algorithm Optimization ◽  
Rotating Blades ◽  
Novel Approach ◽  
Present Technique ◽  
Optimization Function ◽  
Rotating Impeller

Optimum placements of the strain gauges assure reliable vibration measurements of structural components such as rotating blades. Within the framework of cyclic vibration theory, a novel approach has been developed for computation of the optimum gauge positions on tuned bladed discs regarding the determined sensitivity, orthogonality, gradient and distance criteria. The utilized genetic algorithm optimization tool allows for an effective numerical search of suitable solutions of the defined optimization function. A rotating impeller disc represented by a cyclic finite element model demonstrates the application of this method. The present technique can be easily applied to other structural components requiring optimal strain gauge instrumentation.

Repeatability and Extended Time Stability Study of an Additively Printed Strain Gauge Under Different Load Conditions

2021 ◽  
Author(s):  
Pradeep Lall ◽  
Jinesh Narangaparambil ◽  
Tony Thomas ◽  
Kyle Schulze
Keyword(s):  
Strain Gauge ◽  
Printed Electronics ◽  
Performance Testing ◽  
Temperature Limit ◽  
Stability Study ◽  
Strain Gauges ◽  
Gauge Factor ◽  
Wearable Electronics ◽  
Strain Sensing ◽  
Sintering Conditions

Abstract Printed electronics has found new applications in wearable electronics owing to the opportunities for integration, and the ability of sustaining folding, flexing and twisting. Continuous monitoring necessitates the production of sensors, which include temperature, humidity, sweat, and strain sensors. In this paper, a process study was performed on the FR4 board while taking into account multiple printing parameters for the direct-write system. The process parameters include ink pressure, print speed, and stand-off height, as well as their effect on the trace profile and print consistency using white light interferometry analysis. The printed traces have also been studied for different sintering conditions while keeping the FR4 board’s temperature limit in mind. The paper also discusses the effect of sintering conditions on mechanical and electrical properties, specifically shear load to failure and resistivity. The data from this was then used to print strain gauges and compared them to commercially available strain gauges. By reporting the gauge factor, the printed strain gauge has been standardized. The conductive ink’s strain sensing capabilities will be studied under tensile cyclic loading (3-point bending) at various strain rates and maximum strains. Long-term performance testing will be carried out using cyclic tensile loads.

Minimization of the Local Residual Stress in 3D Flip Chip Structures by Optimizing the Mechanical Properties of Electroplated Materials and the Alignment Structure of TSVs and Fine Bumps

2011 ◽  
Author(s):  
Kohta Nakahira ◽  
Hironori Tago ◽  
Fumiaki Endo ◽  
Ken Suzuki ◽  
Hideo Miura
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Thermal Deformation ◽  
Flip Chip ◽  
Flexural Rigidity ◽  
Three Dimensional ◽  
Strain Gauges ◽  
Copper Interconnection ◽  
Induced Stress ◽  
Alignment Structure

Since the thickness of the stacked silicon chips in 3D integration has been thinned to less than 100 μm, the local thermal deformation of the chips has increased drastically because of the decrease of the flexural rigidity of the thinned chips. The clear periodic thermal deformation and thus, the thermal residual stress distribution appears in the stacked chips due to the periodic alignment of metallic bumps, and they deteriorate the reliability of products. In this paper, the dominant structural factors of the local residual stress in a silicon chip are discussed quantitatively based on the results of a three-dimensional finite element analysis and the measurement of the local residual stress in a chip using stress sensor chips. The piezoresistive strain gauges were embedded in the sensor chips. The length of each gauge was 2 μm, and an unit cell consisted of 4 gauges with different crystallographic directions. This alignment of strain gauges enables to measure the tensor component of three-dimensional stress fields separately. Test flip chip substrates were made by silicon chip on which the area-arrayed tin/copper bumps were electroplated. The width of a bump was fixed at 200 μm, and the bump pitch was varied from 400 μm to 1000 μm. The thickness of the copper layer was about 40 μm and that of tin layer was about 10 μm. This tin layer was used for the rigid joint formation by alloying with copper interconnection formed on a stress sensing chip. The measured amplitude of the residual stress increased from about 30 MPa to 250 MPa depending on the combination of materials such as bump, underfill, and interconnections. It was confirmed that both the material constant of underfill and the alignment structure of fine bumps are the dominant factors of the local deformation and stress of a silicon chip mounted on area-arrayed metallic bumps. It was also confirmed experimentally that both the hound’s-tooth alignment between a TSV (Through Silicon Via) and a bump and control of mechanical properties of electroplated copper thin films used for the TSV and bump is indispensable in order to minimize the packaging-induced stress in the three-dimensionally mounted chips. This test chip is very effective for evaluating the packaging-process induced stress in 3D stacked chips quantitatively.

scholarly journals Psychometric evidence of the transcultural adaptation of the Vulnerability Abuse Screening Scale (VASS) for the detection of violence against the elderly

2016 ◽  
Vol 19 (6) ◽  
pp. 958-969 ◽  
Author(s):  
Rodrigo da Silva Maia ◽  
◽  
Eulália Maria Chaves Maia ◽  
Keyword(s):  
Cultural Adaptation ◽  
Pearson Correlation ◽  
Measurement Equivalence ◽  
The Elderly ◽  
Elderly Persons ◽  
Kappa Index ◽  
Four Dimensions ◽  
Univariate Anova ◽  
Psychometric Evidence ◽  
Screening Scale

Abstract Objective: to present preliminary psychometric evidence of the cross-cultural adaptation of the Vulnerability to Abuse Screening Scale. Method: The steps of cultural adaptation verified conceptual, item, semantic and measurement equivalence. For measurement equivalence and verification of the psychometric data of the study samples of 30 and 66 elderly persons, respectively, were used. Descriptive and inferential statistics (KR-20, T-Student Test, Pearson correlation, univariate ANOVA and the Fleiss’ Kappa Index) were used for analysis of results. Results: It was found that the age of the participants ranged between 60 and 84 years, with a majority of older women participants (n=38). The KR-20 value for the overall score of the instrument was 0.688. The values for the four dimensions proposed by the authors of the instrument were 0.528, 0.289, 0.552 and 0.303, respectively. Only the values of the subscales Vulnerability and Coercion proved to be close to those of the original study (0.550 and 0.390). Conclusion: The internal consistency values found in the present study ranged from moderate to good, indicating that the results were satisfactory, despite being initial findings.

scholarly journals Development and validation of a food frequency questionnaire (FFQ-Porto Alegre) for adolescent, adult and elderly populations from Southern Brazil

2010 ◽  
Vol 26 (11) ◽  
pp. 2068-2079 ◽  
Author(s):  
Ruth Liane Henn ◽  
Sandra Costa Fuchs ◽  
Leila Beltrami Moreira ◽  
Flavio Danni Fuchs
Keyword(s):  
Food Frequency Questionnaire ◽  
Pearson Correlation ◽  
Correlation Coefficients ◽  
The Elderly ◽  
Population Based ◽  
Porto Alegre ◽  
Food Frequency ◽  
Dietary Recall ◽  
Epidemiological Surveys ◽  
Adolescents And Adults

This study assessed the validity of a food frequency questionnaire (FFQ-Porto Alegre), covering 135 food items, in comparison with the average of two consecutive 24-hour dietary recall questionnaires for adolescents, adults, and elderly who were randomly selected from a population-based survey. The Pearson correlation coefficients and cross-classification by quartiles of intake were used. The nutrients were log transformed and energy adjusted. The mean of adjusted de-attenuated correlation coefficient for adolescents was 0.44 and ranged from 0.18 (zinc) to 0.69 (folate) and for adult and elderly participants they were, respectively, 0.42, ranging from 0.16 (iron) to 0.73 (energy) and 0.52, ranging from 0.25 (vitamin E) to 0.84 (energy). The average classification percentage into the same or adjacent quartile for the two methods was 74.6% for adolescents, 74.9% for adults, and 81.2% for the elderly population. The FFQ showed fair relative validity for adolescents and adults, and may be used to study the dietary determinants of obesity and non-transmissible diseases in epidemiological surveys.

Sign in / Sign up

Export Citation Format

Share Document