scholarly journals Design and Modelling Process of Soil Improvement with Concrete Strengthening Elements

Author(s):  
Kristóf Lődör ◽  
Balázs Móczár

In recent decades due to the development and diversification of construction technologies, soil improvement procedures became a competitive and cost-effective alternative to increase the load-bearing capacity of the subsoil, while reducing deformations of the structure. Attributed to urbanization, lands with insufficient soil bearing capacity are becoming construction sites, for which it is essential to influence or increase the bearing capacity of the subsoil for the safety and compatibility of structures. Soil reinforcement with concrete elements is used in more and more construction project in Hungary. The structural behavior of traditional pile foundation is well known, and adequate standards are available during the planning process. On the other hand, soil improvement procedures, in our case for the design of rigid inclusion foundation no standards are available only guidelines and recommendations. Because of that in almost all cases, the design phase includes numerical modelling, which is used to prove the efficiency of the system and receive a more accurate picture of the real structural behavior.

2020 ◽  
Vol 6 (3) ◽  
pp. 180-191
Author(s):  
Kavitha Chandrasekaran

Background:: In the long run, synthetic tints were found to be harmful to the chemicals. As a result natural tints have come to be used for their many intrinsic values. The main reason being, then availability of local plants as the main source of natural colorants. Their easy availability in the country being zero cost – effective and planted for other purposes are the main reasons for utilizing them as natural tints. Almost all the parts of the plants, namely stem, leaves, fruits, seeds, barks etc. are used for extracting natural colour. In addition, they are antimicrobial antifungal, insect – repellant deodorant, disinfectant having medicinal values. Methods:: Sweet Indrajao leaves were cleaned by washing with water and dried under direct sunlight and ground as fine powder. A fine strainer was used to remove the wastages. After all these processes, 1-kilogram leaves weighed 318 grams. Then, it is put in 75% ethanol 25% water and heated in a breaker which in kept over a water bath for 2 hours. After this, the contents were filtered and kept in a separate beaker. Bleached fleece draperies stained with stain extract were made to become wet and put into different stain baths which contain the required amount of stain extract and water. Acetic acid was added to it after 20 minutes. The fleece drapery was stained for about one hour at 60oC. The draperies thus stained were removed, squeezed, and put to treatment with metal salts without washing. Different metal salts were used for the treatment using 3% of any one of the chemical mordants like alum, stannous chloride, potassium dichromate, ferrous sulphate, nickel sulphate, copper sulphate and natural mordants such as myrobolan, turmeric, cow dung, Banana sap juice at 60oC for 30 minutes with MLR of 1:30. The stained draperies were washed repeatedly in all the three methods in water and dried in air. At last, the stained draperies were put to soap with soap solution at 60oC for 10 minutes. The draperies were repeatedly washed in water and dried under the sun. Results:: Sweet Indrajao leaves discharged colour easily in alcoholic water. The fleece draperies were stained with chemical and natural mordants. It was observed that the stain uptake was found to be good in post-mordanting method. Ultrasonication has clearly improved the stainability of the draperies at pH 3 and 3.5 values. The pH decreases the stain ability under both Conventional and Ultrasonic conditions. The colour strength increases with an increase in staining temperature in both cases of US and CH methods. Conclusion:: Sweet Indrajao.L has been found to have good ultrasonic potential as a stain plant. The stain uptake as well as the fastness properties of the fleece drapery were found to enhance when metal mordant was used in conjugation with ultra-sonication for the extract of Sweet Indrajao. It was also found that the enhancement of staining ability was better without mordant draperies. The dye extract showed good antibacterial activity against the three bacterial pathogens. Among the three bacterial pathogens, dye extract showed more effective against Escherichia coli pathogens and dye extract showed more effective against Aspergillus pathogens. Hence, the ultrasonic method of drapery staining may be appropriate and beneficial for society at large in future.


2018 ◽  
Vol 2018 ◽  
pp. 1-11
Author(s):  
Kaiyang Wang ◽  
Yanjun Shang

This paper examines the performance of a novel technology, vertical steel floral tube micropiles with double grouting. It is the combination of micropile technology and double grouting technology. A large-scale model tank was applied to impart horizontal bearing capacity, and the slope soil pressure and flexural performance of the micropile were investigated under four experimental conditions. The peak grouting pressure during the double grouting process was defined as the fracturing pressure of the double grouting, and it was positively correlated to the interval time between first grouting and secondary grouting. Compared with traditional grouting, double grouting increased the horizontal bearing capacity of the single micropile with the vertical steel floral tube by 24.42%. The horizontal bearing capacity was also 20.25% higher for the structure with three micropiles, compared with a 3-fold value of horizontal sliding resistance. In the test, the maximum bending moment acting on the pile above the sliding surface was located 2.0–2.5 m away from the pile top, and the largest negative bending moment acting on the pile below the slip surface was located 4.0 m away from the pile top. The ultimate bending moment of the single pile increased by 12.8 kN·m with double grouting, and the bending resistance increased by 96.2%. The experimental results showed that the double grouting technology significantly improved the horizontal bearing capacity of the micropile with the steel floral tube, and the soil reinforcement performance between piles was more pronounced. Also, the shear capacity and the flexural capacity were significantly improved compared with the original technology.


Author(s):  
Steven Wilcox ◽  
Richard Wilkins ◽  
Martin Lyons

Many organisations are currently dealing with long standing legacy issues in clean up, decommissioning and demolition projects. Industry is required to ensure that all bulk articles, substances and waste arisings are adequately characterised and assigned to the correct disposal routes in compliance with UK legislation and best practice. It is essential that data used to support waste sentencing is of the correct type, quality and quantity, and that it is appropriately assessed in order to support defensible, confident decisions that account for inherent uncertainties. AMEC has adopted the Data Quality Objectives (DQO) based methodology and the software package Visual Sample Plan (VSP) to provide a better, faster, and more cost effective approach to meeting regulatory and client requirements, whilst minimising the time spent gathering data and assessing the information. The DQO methodology is based on a scientific approach that requires clear objectives to be established from the outset of a project and that there is a demonstration of acceptability of the results. Through systematic planning, the team develops acceptance or performance criteria for the quality of the data collected and for the confidence in the final decision. The systematic planning process promotes communication between all departments and individuals involved in the decision-making process thus the planning phase gives an open and unambiguous method to support the decisions and enables the decision-makers (technical authorities on the materials of concern) to document all assumptions. The DQO process allows better planning, control and understanding of all the issues. All types of waste can be sentenced under one controllable system providing a more defensible position. This paper will explain that the DQO process consists of seven main steps that lead to a detailed Sampling and Analysis Plan (SAP). The process gives transparency to any assumptions made about the site or material being characterised and identifies individuals involved. The associated calculation effort is reduced using the statistically based sampling models produced with VSP. The first part of this paper explains the DQO based methodology and Visual Sample Plan and the second part shows how the DQO process has been applied in practice.


2021 ◽  
Author(s):  
Hamed Azarbad ◽  
Julien Tremblay ◽  
Luke D. Bainard ◽  
Etienne Yergeau

AbstractNext-generation sequencing is recognized as one of the most popular and cost-effective way of characterizing microbiome in multiple samples. However, most of the currently available amplicon sequencing approaches are inherently limited, as they are often presented based on the relative abundance of microbial taxa, which may not fully represent actual microbiome profiles. Here, we combined amplicon sequencing (16S rRNA gene for bacteria and ITS region for fungi) with real-time quantitative PCR (qPCR) to characterize the rhizosphere microbiome of wheat. We show that the increase in relative abundance of major microbial phyla does not necessarily result in an increase in abundance. One striking observation when comparing relative and quantitative abundances was a substantial increase in the abundance of almost all phyla associated with the rhizosphere of plants grown in soil with no history of water stress as compared with the rhizosphere of plants growing in soil with a history of water stress, which was in contradiction with the trends observed in the relative abundance data. Our results suggest that the estimated absolute abundance approach gives a different perspective than the relative abundance approach, providing complementary information that helps to better understand the rhizosphere microbiome.


2020 ◽  
Vol 5 (4) ◽  
pp. 1237-1252
Author(s):  
Paul Pirrie ◽  
David Campos-Gaona ◽  
Olimpo Anaya-Lara

Abstract. Multi-rotor wind turbines (MRWTs) have been suggested in the literature as a solution to achieving wind turbine systems with capacities greater than 10 MW. MRWTs utilize a large number of small rotors connected to one support structure instead of one large rotor with the aim of circumventing the square cube law. Potential benefits of MRWTs include cost and material savings, standardization of parts, increased control possibilities, and improved logistics for assembly and maintenance. Almost all previous work has focused on mechanical and aerodynamic feasibility, with almost no attention being paid to the electrical systems. In this research eight different topologies of the electrical collection network for MRWTs are analysed to assess which are the most economically and practically viable options. AC and DC collection networks are presented in radial, star, cluster and DC series topologies. Mass, capital cost and losses are estimated based on scaling relationships from the academic literature and up-to-date commercial data. The focus of this study is the assessment of the type of electrical collector topology, so component type and voltage level are kept consistent between topology designs in order to facilitate a fair comparison. Topologies are compared in terms of four main criteria: capital cost, cost effectiveness, total mass and reliability. A comparison table is presented to summarize the findings of the research in a convenient way. It is found that the most cost-effective solutions are the AC radial and AC star topologies, with the least cost-effective being the DC series–parallel and DC cluster topologies. This is due to the high cost of DC–DC converters and DC switchgear along with the lower efficiency of DC converters. Radial designs perform best in terms of efficiency and annual energy capture. DC systems achieve a slightly lower nacelle mass compared to their equivalent AC systems. DC topologies are generally found to be more expensive when compared to their AC counterparts due to the high cost of DC–DC converters and DC switchgear. Star topologies are considered to have the best reliability due to having no shared equipment. The most suitable collection topology for MRWTs is shown to be of the star type, in which each turbine is connected to the step-up transformer via its own cable.


2021 ◽  
Vol 2021 (1) ◽  
Author(s):  
Ya. Samusevych ◽  
A. Temchenko

The key to successful and cost-effective activities of enterprises is the rational organization of the planning process, which concerns financial indicators and involves writing budgets. The article summarizes the theoretical and practical aspects of the organization and implementation of budgeting in industrial enterprises. The study of approaches of different scholars to the interpretation of the essence of the concept of budgeting allowed defining it as a complex economic process of the management cycle. It is developed at the discretion of the enterprise by determining the amount and composition of the costs of individual units of the entity and ensuring coverage of these costs by the resources of the enterprise to achieve the ultimate goal of the entity – to obtain maximum profit at minimum cost, taking into account both internal and external factors. The role of budgeting for industrial enterprises, its main purpose, the list of entities involved in budgeting, as well as the fundamental criteria for budgeting were clarified. Based on the generalization of a number of the most important criteria for the company, the possible types of budgets as well as their advantages and specifics of use depending on the objectives of the entity were generalized and described. The analysis of the basic stages of budgeting which are carried out in the course of activity of the is enterprise carried out, terms of writing and representation of budgets on an example of the monthly, quarterly and annual financial period are considered. It is determined that the budgeting system is a tool of internal financial planning and control, which significantly increases the efficiency of financial management of the enterprise, preventing the irrational use of financial resources both at the planning stage and at the stage of control over their use. Given the lack of established norms and rules for budgeting in the enterprise, optimizing the organization of the budgeting process and the effectiveness of financial planning are the tasks of the internal system of corporate governance.


2011 ◽  
Vol 2011 ◽  
pp. 1-5 ◽  
Author(s):  
G. V. Rama Subbarao ◽  
D. Siddartha ◽  
T. Muralikrishna ◽  
K. S. Sailaja ◽  
T. Sowmya

Soil existing at a particular site may not be appropriate for construction of engineering structures. The present study made an attempt to enhance the geotechnical properties of a soil replaced with industrial wastes having pozzolanic value like rice husk ash (RHA) and fly ash (FA). Soil is replaced with RHA in 2%, 4%, and 6% to dry weight of soil. It is observed that soil replaced with 4% RHA is the optimum for the soil used in this study from geotechnical point of view. To know the influence of fly ash, soil is further replaced with 4% FA along with 4% RHA. It is found that results of soil replacement by both RHA and FA proved to be soil modification and not the improvement. Hence, a cost-effective accelerator like lime is used for further replacing the above soil-4%, RHA-4% FA mix. The optimum lime content is found to be 4%.


Author(s):  
Sergey Nogin ◽  
Jânio Monteiro ◽  
Sergio Gómez Melgar ◽  
José Peyroteo ◽  
António Mortal ◽  
...  

Tourists today are more likely to be concerned with the environment and greener lifestyle choices. In this context, a green flagship of some hotels can be an important selection criteria at the time of selecting one. In the near future, buildings should become nearly zero energy, consuming as low as possible and producing almost all the energy they need, using renewable energy sources. To achieve this goal, hotel buildings need to pass through a transformation process that will make them more efficient. In this process, a decision support platform would be important to help hoteliers monitor their energy consumption, identify which points are consuming more than expected, decide which investments are more cost effective and manage their equipment in an optimum way. This chapter describes the challenges involved in developing such a platform, covering several research and development fields, including Internet of Things networks, ICT, Smart Grids, Renewable Energy, Energy efficiency, as well as algorithms for machine learning and optimization.


2020 ◽  
Vol 7 (1) ◽  
pp. 7 ◽  
Author(s):  
Elisa Mussi ◽  
Federico Mussa ◽  
Chiara Santarelli ◽  
Mirko Scagnet ◽  
Francesca Uccheddu ◽  
...  

In brain tumor surgery, an appropriate and careful surgical planning process is crucial for surgeons and can determine the success or failure of the surgery. A deep comprehension of spatial relationships between tumor borders and surrounding healthy tissues enables accurate surgical planning that leads to the identification of the optimal and patient-specific surgical strategy. A physical replica of the region of interest is a valuable aid for preoperative planning and simulation, allowing the physician to directly handle the patient’s anatomy and easily study the volumes involved in the surgery. In the literature, different anatomical models, produced with 3D technologies, are reported and several methodologies were proposed. Many of them share the idea that the employment of 3D printing technologies to produce anatomical models can be introduced into standard clinical practice since 3D printing is now considered to be a mature technology. Therefore, the main aim of the paper is to take into account the literature best practices and to describe the current workflow and methodology used to standardize the pre-operative virtual and physical simulation in neurosurgery. The main aim is also to introduce these practices and standards to neurosurgeons and clinical engineers interested in learning and implementing cost-effective in-house preoperative surgical planning processes. To assess the validity of the proposed scheme, four clinical cases of preoperative planning of brain cancer surgery are reported and discussed. Our preliminary results showed that the proposed methodology can be applied effectively in the neurosurgical clinical practice both in terms of affordability and in terms of simulation realism and efficacy.


2019 ◽  
Vol 45 (1) ◽  
pp. 81-97 ◽  
Author(s):  
Christine G. Mokher ◽  
Toby J. Park-Gaghan ◽  
Hayley Spencer ◽  
Xinye Hu ◽  
Shouping Hu

Abstract Following a major statewide developmental education reform in Florida, we explored institutional transformation among Florida College System institutions. We used statewide survey data to examine lead administrators’ perceptions of challenges encountered during the planning process, ways in which colleges engaged in sensemaking (i.e., social processes for developing shared understanding) and organizational learning, and perceptions of the institutional transformation processes and outcomes following the reform. We found that institutions engaged in numerous types of sensemaking and organizational learning practices to promote change. Yet, despite different approaches taken to institutional transformation, almost all respondents reported that the change process was highly collaborative and involved a broad range of stakeholders.


Sign in / Sign up

Export Citation Format

Share Document