scholarly journals Composite fabrication from fat extracted limed fleshing: solid waste management in tannery

2021 ◽  
Vol 56 (3) ◽  
pp. 215-222
Author(s):  
MA Hashem ◽  
MHR Sheikh ◽  
Rahamatullah ◽  
M Biswas ◽  
MA Hasan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fourier Transform ◽  
Electron Microscope ◽  
Solid Waste ◽  
Solid Waste Management ◽  
Elongation At Break ◽  
Composite Fabrication ◽  
Negative Effect ◽  
Scanning Electron

In tannery, fleshing is the unavoidable solid waste which has negative effect on the environment. Fleshing contains fat, and protein.In this work, fat extracted fleshing was used for composite fabrication. After collecting limed fleshing, fat was extracted in water bath.The fat extracted fleshing was dried, ground,passes through 80-mesh and homogenized.For proper adhesion and bonding with fleshing powder, epoxy resin and hardener were mixed at various ratios and poured onto an aluminum sheetfor 24 h curing. The mechanical properties of the composite were investigated by tensile strength, elongation at break, and Young’s modulus. The composite was characterized by Fourier Transform Infrared (FTIR) Spectroscopy and Scanning Electron Microscope (SEM) for related functional groups and surface analysis. The investigation provided satisfactory information on the proper bonding of the fleshing powder and resin/hardener. The approach explores the valorization of he waste for managing solid waste in the tannery. Bangladesh J. Sci. Ind. Res.56(3), 215-222, 2021

Properties of Compatibilized SAN/NR Blends

2012 ◽  
Vol 488-489 ◽  
pp. 62-66
Author(s):  
Jareenuch Rojsatean ◽  
Supakij Suttireungwong ◽  
Manus Seadan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Microscope ◽  
Maleic Anhydride ◽  
Impact Strength ◽  
Melt Blending ◽  
Elongation At Break ◽  
Reactive Agents ◽  
Internal Mixer ◽  
Scanning Electron

The blend of poly(styrene-co-acrylonitrile) (SAN) and natural rubber (NR) is immiscible and incompatible which lead to poor mechanical properties. Many methods can be carried out to improve the compatibility. In this work, the potential of various reactive compatibilizers in SAN and NR blend was explored. The morphological and mechanical properties were compared. The melt blending of SAN and NR were prepared in an internal mixer with various types of reactive agent such as styrene-co-maleic anhydride (SMA), maleic anhydride (MA), peroxide and mixed reactive agents. The morphological textures of the blends were investigated by scanning electron microscope. Mechanical properties including tensile strength, impact strength and elongation at break were measured. The results of morphological observations revealed that SAN/NR blend with reactive agent, the mixture of SMA and MA show the smallest and the most uniform dispersed NR particles, where the size of NR particle is about 1 µm. The mechanical properties of the blends revealed impact strength and elongation at break were increased with addition of reactive agents. SAN/NR blend with the mixture of SMA and MA showed the highest elongation at break but it had lower impact strength than the blend with SMA.

Mechanical and Morphology Properties of Polypropylene/ Nano-CaCO3 Composites

2013 ◽  
Vol 774-776 ◽  
pp. 625-628
Author(s):  
Teng Fei Shen ◽  
Fa Chao Wu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Microscope ◽  
Maleic Anhydride ◽  
Interfacial Adhesion ◽  
Tensile Tests ◽  
Melt Blending ◽  
Elongation At Break ◽  
High Fraction ◽  
Scanning Electron

To provide polypropylene (PP) with better excellent mechanical properties, nanoCaCO3 particles are incorporated into PP matrix by melt blending in this work. To improve the mophology between PP and nanoCaCO3, maleic-anhydride grafted PP (PP-g-MAH) was added as a compatibiliser. The results showed that PP-g-MAH indeed enhanced the interfacial adhesion of PP /nanoCaCO3 composites, which is demonstrated by the measurement of scanning electron microscope (SEM). The results of tensile tests revealed that the inclusion of nanoCaCO3 slightly increased modulus and decreased tensile strength and significantly increased the elongation at break. At high fraction of nanoCaCO3, the elongation at break was declined. The nanosized feature, shape and dispersion conditions of nanoCaCO3, played important roles in determining the performances of PP/nanoCaCO3 composites.

Preparation and characterizations of ternary biodegradable blends composed of polylactide, poly(ε-caprolactone), and wood flour

2012 ◽  
Vol 32 (6-7) ◽  
pp. 435-444 ◽  
Author(s):  
Hsin-Tzu Liao ◽  
Chin-San Wu
Keyword(s):  
Mechanical Properties ◽  
Weight Loss ◽  
Tensile Strength ◽  
Fourier Transform ◽  
Wood Flour ◽  
High Price ◽  
Infrared Analysis ◽  
Melt Blending ◽  
Ternary Blends ◽  
Elongation At Break

Abstract Melt blending of polylactide (PLA), poly(ε-caprolactone) (PCL), and wood flour (WF) was performed in an effort to overcome the major drawbacks (brittleness and high price) of PLA. In addition, the acrylic acid (AA)-grafted PLA70PCL30 (PLA70PCL30-g-AA) was used as the alternative for the preparation of ternary blends to improve the compatibility and the dispersability of WF within the PLA70PCL30 matrix. As expected, PCL improved the elongation at break and the toughness of PLA but decreased the tensile strength and modulus. Because the hydrophilic WF is dispersed physically in the hydrophobic PLA70PCL30 matrix, as the result of Fourier transform infrared analysis, the mechanical properties of PLA70PCL30 became noticeably worse when it was blended with WF. This problem was successfully conquered by using PLA70PCL30-g-AA to replace PLA70PCL30 due to the formation of an ester carbonyl group between PLA70PCL30-g-AA and WF. Furthermore, the PLA70PCL30-g-AA/WF blend provided a plateau tensile strength at break when the WF content was up to 50 wt%. PLA70PCL30/WF exhibited a tensile strength at break of approximately 3–25 MPa more than PLA70PCL30-g-AA/WF. By using p-cresol and tyrosinase, the enzymatic biodegradable test showed that PLA70PCL30-g-AA is somewhat more biodegradable than PLA70PCL30 because the former has better water absorption. After 16 weeks, the weight loss of the PLA70PCL30/WF (50 wt%) composite was >80%. PLA70PCL30-g-AA/WF exhibited a weight loss of approximately 1–12 wt% more than PLA70PCL30-g-AA/WF. It was also found that the addition of WF to PLA70PCL30 or PLA70PCL30-g-AA decreased the crystallinity of PLA and PCL in PLA70PCL30 or PLA70PCL30-g-AA and then increased their biodegradable property.

Effect of Functionalized MWCNT on the Mechanical and Dielectric Properties of PMMA Nanocomposites

2018 ◽  
Vol 18 (06) ◽  
pp. 1850035
Author(s):  
Punyapriya Mishra ◽  
Narasingh Deep ◽  
Sagarika Pradhan ◽  
Vikram G. Kamble
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Dielectric Constant ◽  
Tensile Strength ◽  
Electron Microscope ◽  
Dielectric Properties ◽  
Conductive Polymer ◽  
Mechanical Tests ◽  
Surface Structures ◽  
Scanning Electron

Carbon nanotubes (CNTs) are widely explained in fundamental blocks of nanotechnology. These CNTs exhibit much greater tensile strength than steel, even almost similar to copper, but they have higher ability to carry much higher currents, they seem to be a magical material with all these mentioned properties. In this paper, an attempt has been made to incorporate this wonder material, CNT, (with varying percentages) in polymeric matrix (Poly methyl methacrylate (PMMA)) to create a new conductive polymer composite. Various mechanical tests were carried out to evaluate its mechanical properties. The dielectric properties such as dielectric loss and dielectric constant were evaluated with the reference of temperature and frequency. The surface structures were analyzed by Scanning Electron Microscope (SEM).

scholarly journals Mechanical Properties of Sigma 1140+ Sic Fibres Prior and after Composite Processing

2000 ◽  
Vol 9 (4) ◽  
pp. 096369350000900 ◽  
Author(s):  
C. Gonzalez ◽  
J. Llorca
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Microscope ◽  
Elastic Modulus ◽  
Weibull Modulus ◽  
Fibre Diameter ◽  
Tensile Tests ◽  
Fibre Strength ◽  
Composite Processing ◽  
Scanning Electron

The effect of processing on the mechanical properties of Sigma 1140+ SiC fibres was studied through tensile tests carried out on pristine Sigma 1140+ SiC fibres and on fibres extracted from a Ti-6A1-4V-matrix composite. The elastic modulus and the tensile strength were computed after measuring carefully the fibre diameter. The characteristic fibre strength was reduced by 20% and the Weibull modulus by half during composite processing. The analysis of the fracture surfaces in the scanning electron microscope showed that the strength-limiting defects were located around the tungsten core in pristine fibres and predominantly at the surface in fibres extracted from the composite panels. These latter defects were nucleated by the mechanical stresses generated on the fibres during the panel consolidation.

scholarly journals Splitting of Islands-in-the-Sea Fibers (PA6/COPET) during Hydroentangling of Nonwovens

2007 ◽  
Vol 2 (4) ◽  
pp. 155892500700200 ◽  
Author(s):  
Mbwana Suleiman Ndaro ◽  
Xiang-yu Jin ◽  
Ting Chen ◽  
Chong-wen Yu
Keyword(s):  
Tensile Strength ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Water Jet ◽  
Elongation At Break ◽  
Sem Micrographs ◽  
Fiber Splitting ◽  
Data Analyses ◽  
Scanning Electron

This paper summarizes the investigations of hydroentangled islands-in-the-sea (PA6/COPET) fiber webs. An increase in water jet pressure improved the tensile strength and fiber splitting while elongation at break decreased. Scanning Electron Microscope (SEM) micrographs and ANOVA (MS Excel ™) were used for characterizing fiber splitting and data analyses respectively. It can be concluded that with a new innovation in spinnerette design and modification of co-polyester structure, PA6/COPET, fibers can be split in the hydroentanglement process without dissolution of the sea component.

Effect of Mo and Bi on Mechanical Properties of Zr-Fe-Cr Alloy at Room Temperature

2013 ◽  
Author(s):  
B. F. Luan ◽  
L. Q. Yang ◽  
T. G. Wei ◽  
K. L. Murty ◽  
C. S. Long ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Microscope ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Room Temperature ◽  
Mechanical Performance ◽  
Microstructure Observation ◽  
Scanning Electron ◽  
Zr Alloy

To investigate the effects of Mo and Bi on mechanical properties of a Zr-Fe-Cr alloy at room temperature, seven Zr-Fe-Cr-Mo-Bi alloys with different compositions were designed. They were subjected to a series of rolling processes and heat treatments, and then sampled to measure mechanical properties by hardness and tensile test and to characterize microstructures by scanning electron microscope (SEM) and electron channel contrast (ECC) technique. Results indicated that among them two types of Zr-Fe-Cr-Mo-Bi alloys achieve the designed goals on mechanical properties and have the following advantages: (i) the hardness of the alloys, up to 334HV after annealing, is 40% higher than traditional Zr-4. (ii) The yield strength (YS) and ultimate tensile strength (UTS) of the alloys are 526 MP a and 889 MP a after hot rolling and annealing, markedly higher than the traditional Zr alloy. (iii) Good plasticity of the new Zr-Fe-Cr-Mo-Bi alloy is obtained with about 40% elongation, which is greatly higher than the Zr-Fe-Cr-Mo alloy thanks to the addition of Bi offsetting the disadvantage of addition Mo. Furthermore, according to observations of the microstructure observation, the reasons of the effect of the Mo and Bi elements on the mechanical performance of Zr-Fe-Cr alloy were studied and discussed.

Study of Microstructure and Mechanical Properties of Extrued Spray Forming Al-8.5Fe-1.3V-1.7Si Alloy

2013 ◽  
Vol 750-752 ◽  
pp. 671-674
Author(s):  
Rong Hua Zhang ◽  
Yong An Zhang ◽  
Bao Hong Zhu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Microscope ◽  
Yield Strength ◽  
Scanning Electron Microscope ◽  
Room Temperature ◽  
Extrusion Process ◽  
Spray Forming ◽  
Microstructure And Mechanical Properties ◽  
Scanning Electron

In this paper, the Al-8.5Fe-1.3V-1.7Si alloys were fabricated by spray forming and extrusion process. The microstructure and mechanical properties of the alloy were investigated by means of metallographic, scanning electron microscope and tensile test. The results indicate that the tensile strength of the extrued alloys can reach 353MPa, the yield strength 300MPa, elongation 19.12%, at room temperature. At 250°C, the tensile strength of the extrued alloys can reach 221MPa, the yield strength 208MPa, elongation 13.33%.

In Situ Composites: Effect of Intermolecular Hydrogen Bonds on Polyamide 66/TLCP Blends

2007 ◽  
Vol 546-549 ◽  
pp. 1515-1520
Author(s):  
Zhuo Zhang ◽  
Hong Jun Guo ◽  
Wei He ◽  
Wen Xion Zhang
Keyword(s):  
Mechanical Properties ◽  
Fourier Transform ◽  
Electron Microscope ◽  
Liquid Crystalline ◽  
Polyamide 66 ◽  
Intermolecular Hydrogen Bonds ◽  
In Situ Composites ◽  
Infra Red ◽  
Scanning Electron

The thermotropic liquid crystalline copolyamide (TLCPa) was synthesized and the in situ composites for TLCPa/Polyamides 66 (PA66) were prepared by melting extrusion. As revealed by differential scanning calorimeter (DSC), depression of the melting point and the crystallinity of PA66 indicated that the miscibility was enhanced via intermolecular H-bonds. Characteristic absorption shifts of C=O groups of TLCPa/PA66 in Fourier transform infra-red spectra (FTIR) confirmed the existence of H-bonds. Scanning electron microscope (SEM) observation showed that the shape of TLCPa phase change in matrix with increasing TLCPa content. Mechanical properties of blends were significantly improved by good interface adhesion and TLCPa fibrils generation.

Study on Anti-Fog Films of Polyethylene Modified with Inorganic Micrometer Diatomite

2012 ◽  
Vol 200 ◽  
pp. 347-350
Author(s):  
Wei He ◽  
Qing Hong Fang ◽  
Wei Lin ◽  
A.S. Luyt ◽  
Tie Jun Ge
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fourier Transform ◽  
Surface Treatment ◽  
Fourier Transform Infrared ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Elongation At Break ◽  
Treatment Agent ◽  
Infrared Spectrometer

Anti-fog films of low density polyethylene (LDPE) modified with micrometer diatomite were prepared by a process of blow molding. Through examination of antifogging property of the film added the anti-fog agents, the modification effectiveness of inorganic micrometer diatomite and the influence of different treating agents were studied with Fourier transform infrared spectrometer (FTIR), mechanical properties, and antifogging performances. The results indicate that the anti-fog property of the film can be improved by premixing inorganic micrometer diatomite with the anti-fog agents; the film modified by inorganic micrometer diatomite added surface treatment agent has obviously effectiveness anti-fog properties than that the films modified only by the anti-fog agents. Addition of polyacrylamide can make the anti-fog durability of the films modified by inorganic micrometer diatomite be further prolonged. It was observed that the tensile strength does not show any decrease, however, elongation at break show a massive decreased.

Sign in / Sign up

Export Citation Format

Share Document