scholarly journals Removal of Different Thicknesses Influences the Repair Bond Strength of Dental Resin Composites

2021 ◽  
Vol 8 ◽  
Author(s):  
Kai Yu ◽  
Minting Wan ◽  
Kui Shi ◽  
Longjian Xue ◽  
Zhi Chen ◽  
...  
Keyword(s):  
Contact Angle ◽  
Bond Strength ◽  
Water Contact Angle ◽  
Positive Control ◽  
Combination Group ◽  
Resin Composites ◽  
Third Molars ◽  
Dental Resin ◽  
Microtensile Bond Strength ◽  
Water Contact

This study investigates the repair bond strength of aged resin composites after removing different thicknesses, determine the repair performance using the same or different resin composites and describe the treated surfaces after ageing. Seventy simulated class I cavities were prepared in extracted human third molars were randomly divided into two groups and restored with a nanofilled (Filtek Z350) or a microhybrid (Clearfil APX) composite. Five specimens without ageing in each group acted as a positive control for microtensile bond strength (MTBS) test. After thermocycling, each group was randomly divided into two subgroups: Group RT1, 1 mm removed and Group RT3, 3 mm removed, followed by roughening. Ten specimens in each subgroup were repaired with the same or different composites, and MTBS tests were conducted. The surface roughness (Sa), and water contact angle of the remaining five specimens in each subgroup were measured. In every combination group, Group RT3 showed significantly higher MTBS values than Group RT1, and identical composite was not compulsory for higher repair bond strength. Removal thickness had no significant effect on the Sa in same composite group. In both the Z350 and APX groups, the water contact angle decreased with increasing removal thickness.

Long-Term Stable Metal Organic Framework (MOF) Based Mixed Matrix Membranes for Ultrafiltration

2020 ◽  
Author(s):  
Muayad Al-shaeli ◽  
Stefan J. D. Smith ◽  
Shanxue Jiang ◽  
Huanting Wang ◽  
Kaisong Zhang ◽  
...  
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Mixed Matrix Membranes ◽  
Recovery Ratio ◽  
Mixed Matrix ◽  
Water Contact ◽  
Membrane Performance ◽  
Metal Organic ◽  
Matrix Membranes

<p>In this study, novel <a>mixed matrix polyethersulfone (PES) membranes</a> were synthesized by using two different kinds of metal organic frameworks (MOFs), namely UiO-66 and UiO-66-NH<sub>2</sub>. The composite membranes were characterised by SEM, EDX, FTIR, PXRD, water contact angle, porosity, pore size, etc. Membrane performance was investigated by water permeation flux, flux recovery ratio, fouling resistance and anti-fouling performance. The stability test was also conducted for the prepared mixed matrix membranes. A higher reduction in the water contact angle was observed after adding both MOFs to the PES and sulfonated PES membranes compared to pristine PES membranes. An enhancement in membrane performance was observed by embedding the MOF into PES membrane matrix, which may be attributed to the super-hydrophilic porous structure of UiO-66-NH<sub>2</sub> nanoparticles and hydrophilic structure of UiO-66 nanoparticles that could accelerate the exchange rate between solvent and non-solvent during the phase inversion process. By adding the MOFs into PES matrix, the flux recovery ratio was increased greatly (more than 99% for most mixed matrix membranes). The mixed matrix membranes showed higher resistance to protein adsorption compared to pristine PES membranes. After immersing the membranes in water for 3 months, 6 months and 12 months, both MOFs were stable and retained their structure. This study indicates that UiO-66 and UiO-66-NH<sub>2</sub> are great candidates for designing long-term stable mixed matrix membranes with higher anti-fouling performance.</p>

scholarly journals Surface modification of PMMA polymer and its composites with PC61BM fullerene derivative using an atmospheric pressure microwave argon plasma sheet

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Andrzej Sikora ◽  
Dariusz Czylkowski ◽  
Bartosz Hrycak ◽  
Magdalena Moczała-Dusanowska ◽  
Marcin Łapiński ◽  
...  
Keyword(s):  
Contact Angle ◽  
Surface Modification ◽  
Chemical Composition ◽  
Water Contact Angle ◽  
Plasma Sheet ◽  
Atmospheric Pressure ◽  
Argon Plasma ◽  
Fullerene Derivative ◽  
Water Contact ◽  
Pmma Polymer

AbstractThis paper presents the results of experimental investigations of the plasma surface modification of a poly(methyl methacrylate) (PMMA) polymer and PMMA composites with a [6,6]-phenyl-C61-butyric acid methyl ester fullerene derivative (PC61BM). An atmospheric pressure microwave (2.45 GHz) argon plasma sheet was used. The experimental parameters were: an argon (Ar) flow rate (up to 20 NL/min), microwave power (up to 530 W), number of plasma scans (up to 3) and, the kind of treated material. In order to assess the plasma effect, the possible changes in the wettability, roughness, chemical composition, and mechanical properties of the plasma-treated samples’ surfaces were evaluated by water contact angle goniometry (WCA), atomic force microscopy (AFM), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). The best result concerning the water contact angle reduction was from 83° to 29.7° for the PMMA material. The ageing studies of the PMMA plasma-modified surface showed long term (100 h) improved wettability. As a result of plasma treating, changes in the samples surface roughness parameters were observed, however their dependence on the number of plasma scans is irregular. The ATR-FTIR spectra of the PMMA plasma-treated surfaces showed only slight changes in comparison with the spectra of an untreated sample. The more significant differences were demonstrated by XPS measurements indicating the surface chemical composition changes after plasma treatment and revealing the oxygen to carbon ratio increase from 0.1 to 0.4.

scholarly journals Physicochemical Properties and Biocompatibility of Electrospun Polycaprolactone/Gelatin Nanofibers

2021 ◽  
Vol 18 (9) ◽  
pp. 4764
Author(s):  
Wei Lee Lim ◽  
Shiplu Roy Chowdhury ◽  
Min Hwei Ng ◽  
Jia Xian Law
Keyword(s):  
Contact Angle ◽  
Physicochemical Properties ◽  
Water Contact Angle ◽  
Ligament Injury ◽  
Great Promise ◽  
Composition Analysis ◽  
Water Contact ◽  
Tenogenic Differentiation ◽  
Good Biocompatibility ◽  
Tissue Grafts

Tissue-engineered substitutes have shown great promise as a potential replacement for current tissue grafts to treat tendon/ligament injury. Herein, we have fabricated aligned polycaprolactone (PCL) and gelatin (GT) nanofibers and further evaluated their physicochemical properties and biocompatibility. PCL and GT were mixed at a ratio of 100:0, 70:30, 50:50, 30:70, 0:100, and electrospun to generate aligned nanofibers. The PCL/GT nanofibers were assessed to determine the diameter, alignment, water contact angle, degradation, and surface chemical analysis. The effects on cells were evaluated through Wharton’s jelly-derived mesenchymal stem cell (WJ-MSC) viability, alignment and tenogenic differentiation. The PCL/GT nanofibers were aligned and had a mean fiber diameter within 200–800 nm. Increasing the GT concentration reduced the water contact angle of the nanofibers. GT nanofibers alone degraded fastest, observed only within 2 days. Chemical composition analysis confirmed the presence of PCL and GT in the nanofibers. The WJ-MSCs were aligned and remained viable after 7 days with the PCL/GT nanofibers. Additionally, the PCL/GT nanofibers supported tenogenic differentiation of WJ-MSCs. The fabricated PCL/GT nanofibers have a diameter that closely resembles the native tissue’s collagen fibrils and have good biocompatibility. Thus, our study demonstrated the suitability of PCL/GT nanofibers for tendon/ligament tissue engineering applications.

Osteoconductivity of Superhydrophilic Ti- and Zr-Alloy for Biomedical Application

2016 ◽  
Vol 879 ◽  
pp. 2524-2527
Author(s):  
Masazumi Okido ◽  
Kensuke Kuroda
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Strong Influence ◽  
Biomedical Application ◽  
Hydrophobic Surface ◽  
Hydrophilic Surface ◽  
Water Contact ◽  
Zr Alloy ◽  
Zr Alloys

Surface hydrophilicity is considered to have a strong influence on the biological reactions of bone-substituting materials. However, the influence of a hydrophilic or hydrophobic surface on the osteoconductivity is not completely clear. In this study, we produced super-hydrophilic and hydrophobic surface on Ti-and Zr-alloys. Hydrothermal treatment at 180 oC for 180 min. in the distilled water and immersion in x5 PBS(-) brought the super-hydrophilic surface (water contact angle < 10 (deg.)) and heat treatment of as-hydrothermaled the hydrophobic surface. The osteoconductivity of the surface treated samples with several water contact angle was evaluated by in vivo testing. The surface properties, especially water contact angle, strongly affected the osteoconductivity and protein adsorbability, and not the surface substance.

scholarly journals Vertical Orientation of Liquid Crystal on Polystyrene Substituted with n-Alkylbenzoate-p-oxymethyl Pendant Group as a Liquid Crystal Precursor

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2058
Author(s):  
Kyutae Seo ◽  
Hyo Kang
Keyword(s):  
Contact Angle ◽  
Liquid Crystal ◽  
Water Contact Angle ◽  
Polymer Films ◽  
Molar Fraction ◽  
Side Chain ◽  
Pendant Group ◽  
Polymer Modification ◽  
Vertical Orientation ◽  
Water Contact

We synthesized a series of polystyrene derivatives modified with precursors of liquid crystal (LC) molecules via polymer modification reactions. Thereafter, the orientation of the LC molecules on the polymer films, which possess part of the corresponding LC molecular structure, was investigated systematically. The precursors and the corresponding derivatives used in this study include ethyl-p-hydroxybenzoate (homopolymer P2BO and copolymer P2BO#, where # indicates the molar fraction of ethylbenzoate-p-oxymethyl in the side chain (# = 20, 40, 60, and 80)), n-butyl-p-hydroxybenzoate (P4BO), n-hexyl-p-hydroxybenzoate (P6BO), and n-octyl-p-hydroxybenzoate (P8BO). A stable and uniform vertical orientation of LC molecules was observed in LC cells fabricated with P2BO#, with 40 mol% or more ethylbenzoate-p-oxymethyl side groups. In addition, the LC molecules were oriented vertically in LC cells fabricated with homopolymers of P2BO, P4BO, P6BO, and P8BO. The water contact angle on the polymer films can be associated with the vertical orientation of the LC molecules in the LC cells fabricated with the polymer films. For example, vertical LC orientation was observed when the water contact angle of the polymer films was greater than ~86°. Good orientation stability was observed at 150 °C and with 20 J/cm2 of UV irradiation for LC cells fabricated with the P2BO film.

scholarly journals Facile Fabrication of Multifunctional ZnO Urchins on Surfaces

2018 ◽  
Vol 2 (4) ◽  
pp. 74 ◽  
Author(s):  
Abinash Tripathy ◽  
Patryk Wąsik ◽  
Syama Sreedharan ◽  
Dipankar Nandi ◽  
Oier Bikondoa ◽  
...  
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Surface Density ◽  
Room Temperature ◽  
High Surface ◽  
Secondary Growth ◽  
Water Contact ◽  
Growth Step ◽  
Si Substrates ◽  
Wide Range

Functional ZnO nanostructured surfaces are important in a wide range of applications. Here we report the simple fabrication of ZnO surface structures at near room temperature with morphology resembling that of sea urchins, with densely packed, μm-long, tapered nanoneedles radiating from the urchin center. The ZnO urchin structures were successfully formed on several different substrates with high surface density and coverage, including silicon (Si), glass, polydimethylsiloxane (PDMS), and copper (Cu) sheets, as well as Si seeded with ZnO nanocrystals. Time-resolved SEM revealed growth kinetics of the ZnO nanostructures on Si, capturing the emergence of “infant” urchins at the early growth stage and subsequent progressive increases in the urchin nanoneedle length and density, whilst the spiky nanoneedle morphology was retained throughout the growth. ε-Zn(OH)2 orthorhombic crystals were also observed alongside the urchins. The crystal structures of the nanostructures at different growth times were confirmed by synchrotron X-ray diffraction measurements. On seeded Si substrates, a two-stage growth mechanism was identified, with a primary growth step of vertically aligned ZnO nanoneedle arrays preceding the secondary growth of the urchins atop the nanoneedle array. The antibacterial, anti-reflective, and wetting functionality of the ZnO urchins—with spiky nanoneedles and at high surface density—on Si substrates was demonstrated. First, bacteria colonization was found to be suppressed on the surface after 24 h incubation in gram-negative Escherichia coli (E. coli) culture, in contrast to control substrates (bare Si and Si sputtered with a 20 nm ZnO thin film). Secondly, the ZnO urchin surface, exhibiting superhydrophilic property with a water contact angle ~ 0°, could be rendered superhydrophobic with a simple silanization step, characterized by an apparent water contact angle θ of 159° ± 1.4° and contact angle hysteresis ∆θ < 7°. The dynamic superhydrophobicity of the surface was demonstrated by the bouncing-off of a falling 10 μL water droplet, with a contact time of 15.3 milliseconds (ms), captured using a high-speed camera. Thirdly, it was shown that the presence of dense spiky ZnO nanoneedles and urchins on the seeded Si substrate exhibited a reflectance R < 1% over the wavelength range λ = 200–800 nm. The ZnO urchins with a unique morphology fabricated via a simple route at room temperature, and readily implementable on different substrates, may be further exploited for multifunctional surfaces and product formulations.

Fast and simple fabrication of SiO2/poly(vinylidene fluoride) coated cotton fabrics with asymmetric wettability via a facile spray-coating route

2018 ◽  
Vol 89 (6) ◽  
pp. 1013-1026 ◽  
Author(s):  
Rongrong Yu ◽  
Mingwei Tian ◽  
Lijun Qu ◽  
Shifeng Zhu ◽  
Jianhua Ran ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Contact Angle ◽  
Water Contact Angle ◽  
Vinylidene Fluoride ◽  
Spray Coating ◽  
Cotton Fabrics ◽  
Water Repellent ◽  
Water Contact ◽  
Repellent Property ◽  
Poly Vinylidene Fluoride

Cotton fabrics with hydrophilic-to-hydrophobic asymmetric surfaces are attractive as potential utilizable structures for functional garments. The spray-coating route could be deemed as a fast and simple way to achieve asymmetric surfaces. In this paper, SiO2 nanoparticles with size ∼ 205 nm were synthesized via the modified sol-gel method, and then modified with poly(vinylidene fluoride) (PVDF) to form a hydrophobic surface. The SiO2 nanoparticles modified with PVDF were uniformly deposited on the outer surface of cotton fabric aided with the robust air flow force from the sprayer. The morphology and chemical structures were characterized by scanning electron microscopy, mapping, atomic force microscopy, X-ray photoelectron spectroscopy and Fourier-transform infrared spectroscopy. The results indicated that SiO2 nanoparticles were evenly deposited on the surface of cotton fibers and stable interfacial interaction occurred between SiO2 and PVDF molecular chains. The existence of SiO2 could increase the roughness of the fabric surface, which could enhance the water-repellent property of the coated fabrics. Furthermore, the water-repellent property and thermal insulation properties were evaluated via the water contact angle and thermal conductivity tests, respectively, and the results showed that 20 wt.% SiO2/PVDF fabric achieved a desirable level of contact angle, 136.6°, which was the largest water contact angle among all the samples, and the lowest thermal conductivity of 0.033 W/mK, resulting from the existence of SiO2 nanoparticles. Such a fast and simple spray-coating strategy could be widely introduced into asymmetric fabric modification, and such asymmetric fabrics with reasonable water-repellent and thermal insulating outer surfaces could act as candidates in the field of functional garments.

Sign in / Sign up

Export Citation Format

Share Document