scholarly journals Experimental Evaluation of the Ventilation Effectiveness of Corner Stratum Ventilation in an Office Environment

Buildings ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 169
Author(s):  
Arman Ameen ◽  
Gasper Choonya ◽  
Mathias Cehlin
Keyword(s):  
Ventilation System ◽  
Heat Removal ◽  
Tracer Gas ◽  
Air Velocity ◽  
Flow Rates ◽  
Office Environment ◽  
Laboratory Environment ◽  
Ventilation Effectiveness ◽  
Local Thermal Comfort ◽  
Velocity Turbulence

An experimental study was conducted in a room resembling an office in a laboratory environment. The study involved investigating the ability of corner-placed stratum ventilation in order to evaluate the ventilation’s effectiveness and local thermal comfort. At fixed positions, the air temperature, air velocity, turbulence intensity, and tracer gas decay measurements were carried out. The results show that corner-placed stratum ventilation behaves very similar to a mixing ventilation system when considering air change effectiveness. The performance of the system was better at lower supply air flow rates for heat removal effectiveness. For the heating cases, the draught rates were all very low, with the maximum measured value of 12%. However, for the cooling cases, the maximum draught rate was 20% and occurred at ankle level in the middle of the room.

scholarly journals Experimental Investigation of Ventilation Performance of Different Air Distribution Systems in an Office Environment—Heating Mode

Energies ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1835 ◽  
Author(s):  
Arman Ameen ◽  
Mathias Cehlin ◽  
Ulf Larsson ◽  
Taghi Karimipanah
Keyword(s):  
Thermal Comfort ◽  
Distribution Systems ◽  
Cold Climate ◽  
Air Distribution ◽  
Temperature Pattern ◽  
Office Environment ◽  
Ventilation Effectiveness ◽  
Local Thermal Comfort ◽  
Heating Mode ◽  
Occupied Zone

A vital requirement for all-air ventilation systems are their functionality to operate both in cooling and heating mode. This article experimentally investigates two newly designed air distribution systems, corner impinging jet (CIJV) and hybrid displacement ventilation (HDV) in comparison against a mixing type air distribution system. These three different systems are examined and compared to one another to evaluate their performance based on local thermal comfort and ventilation effectiveness when operating in heating mode. The evaluated test room is an office environment with two workstations. One of the office walls, which has three windows, faces a cold climate chamber. The results show that CIJV and HDV perform similar to a mixing ventilation in terms of ventilation effectiveness close to the workstations. As for local thermal comfort evaluation, the results show a small advantage for CIJV in the occupied zone. Comparing C2-CIJV to C2-CMV the average draught rate (DR) in the occupied zone is 0.3% for C2-CIJV and 5.3% for C2-CMV with the highest difference reaching as high as 10% at the height of 1.7 m. The results indicate that these systems can perform as well as mixing ventilation when used in offices that require moderate heating. The results also show that downdraught from the windows greatly impacts on the overall airflow and temperature pattern in the room.

scholarly journals Air Terminal Devices Developed for Personal Ventilation Systems

Energies ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1688
Author(s):  
Imre Csáky
Keyword(s):  
Thermal Comfort ◽  
Air Flow ◽  
Ventilation System ◽  
Air Velocity ◽  
Head Region ◽  
Personal Ventilation ◽  
The University ◽  
Velocity Turbulence ◽  
Ventilation Systems

Using the personal ventilation systems may improve the thermal comfort sensation. At the University of Debrecen, a personal ventilation system was developed named ALTAIR. This paper presents the results of mean air velocity, turbulence grade, and draught measurements related to newly developed air terminal devices which are connected to the ALTAIR personal ventilation system. In order to define the measurement points it was essential to test the new air terminal devices (ATDs) in front of a black wall and smoke puffs. A series of measurements were carried out with isothermal air flow, mean air velocity, turbulence grade, and draught around the occupant head region in order to improve the thermal comfort sensation. Five different ATDs were analyzed.

Novel Lightweight Metal Foam Heat Exchangers

2001 ◽  
Author(s):  
David P. Haack ◽  
Kenneth R. Butcher ◽  
T. Kim ◽  
T. J. Lu
Keyword(s):  
Heat Exchange ◽  
Pore Size ◽  
Heat Exchangers ◽  
Metal Foam ◽  
Heat Removal ◽  
Random Orientation ◽  
Flow Rates ◽  
Small Pore ◽  
Complex Heat Exchange ◽  
Flow Through

Abstract An overview of open cell metal foam materials with application to advanced heat exchange devices is presented. The metal foam materials considered consist of interconnected cells in a random orientation. Metal foam materials, manufacture and fabrication into complex heat exchange components are described. Experiments with flat foam panels brazed to copper sheets shows increasing heat removal effectiveness with decreasing product pore size at equivalent coolant flow rates. However, the high-pressure drop associated with flow through small pore-size material makes the use of larger pore size material more attractive.

Validation of Film Evaporation Model in GASFLOW-MPI

2018 ◽  
Author(s):  
Li Yabing ◽  
Zhang Han ◽  
Xiao Jianjun
Keyword(s):  
Experimental Data ◽  
Wall Temperature ◽  
Cooling System ◽  
Numerical Study ◽  
Thermal Power ◽  
Heat Removal ◽  
Air Velocity ◽  
Evaporation Model ◽  
Film Evaporation ◽  
Test Region

A dynamic film model is developed in the parallel CFD code GASFLOW-MPI for passive containment cooling system (PCCS) utilized in nuclear power plant like AP1000 and CAP1400. GASFLOW-MPI is a widely validated parallel CDF code and has been applied to containment thermal hydraulics safety analysis for different types of reactors. The essential issue for PCCS is the heat removal capability. Research shows that film evaporation contributes most to the heat removal capability for PCCS. In this study, the film evaporation model is validated with separate effect test conducted on the EFFE facility by Pisa University. The test region is a rectangle gap with 0.1m width, 2m length, and 0.6m depth. The water film flowing from the top of the gap is heated by a heating plate with constant temperature and cooled by countercurrent air flow at the same time. The test region model is built and analyzed, through which the total thermal power and evaporation rate are obtained to compare with experimental data. Numerical result shows good agreement with the experimental data. Besides, the influence of air velocity, wall temperature and gap widths are discussed in our study. Result shows that, the film evaporation has a positive correlation with air velocity, wall temperature and gap width. This study can be fundamental for our further numerical study on PCCS.

Experimental Analysis of Different Coolants Used in Plasma Cutting Operation for the Improved Electrode Life

2015 ◽  
Vol 719-720 ◽  
pp. 46-49 ◽  
Author(s):  
Ginka Ranga Janardhana ◽  
Mani Senthil Kumar ◽  
B. Dhanasekar
Keyword(s):  
Temperature Rise ◽  
Metal Cutting ◽  
Cooling System ◽  
Heat Removal ◽  
Plasma Cutting ◽  
Life Test ◽  
Flow Rates ◽  
Optimal Flow ◽  
Cutting Operation ◽  
The Impact

The plasma cutting technology has been emerged as a developing technology which finds tremendous potential in fabrication and metal cutting industries. Thus for the cutting operation, the electrode inside the plasma torch plays a vital role for the plasma arc generation. The temperature of the arc is very high and at the electrode is around 3500°C. The cutting torch requires proper cooling system in order to prevent the electrode from quick wear due to the existence of high thermal gradient. The presented work aimed to study the impact of three coolants propylene glycol, ethylene glycol and de-ionized water flow over the electrode life. The experimental setups were arranged to study the heat transfer capabilities of the three coolants for different flow values and aimed to achieve the optimal flow rates for the efficient heat removal. The electrode life test trials were conducted to measure the electrode life for the flow values of three coolants in the temperature rise test. The optimal flow rates arrived from temperature rise test and the electrode life measured from life test are compared for the three coolant cases considered.

scholarly journals A comparison between tracer gas and tracer particle techniques in evaluating the efficiency of ventilation in operating theatres

1983 ◽  
Vol 91 (3) ◽  
pp. 509-519 ◽  
Author(s):  
Per-Arne Andersson ◽  
Anna Hambraeus ◽  
Ulla Zettersten ◽  
Bengt Ljungqvist ◽  
Kenneth Neikter ◽  
...  
Keyword(s):  
Tracer Particle ◽  
Ventilation System ◽  
Airborne Bacteria ◽  
Tracer Gas ◽  
Operating Theatres ◽  
Ventilation Rates ◽  
Operation Wound

Operating theatres are ventilated for a number of reasons, one of them being to keep numbers of airborne bacteria low at the operation wound. No matter how air is brought into the room, bacteria are removed by dilution rather than by air currents, because of turbulence caused by heat liberated by people and equipment and by movement in the room (Lidwell & Williams, 1960). With ventilation rates up to 20 air changes/hour, the dilution may differ at different sites in the room depending on the design of its ventilation system.

Evaluation of Indoor Climate in Big Lecture Hall

2019 ◽  
Vol 887 ◽  
pp. 475-483
Author(s):  
Mária Budiaková
Keyword(s):  
Thermal Comfort ◽  
Ventilation System ◽  
Winter Season ◽  
Point Of View ◽  
Lecture Hall ◽  
Experimental Measurements ◽  
Optimal Parameters ◽  
Indoor Climate ◽  
Air Velocity ◽  
Operation System

The paper is oriented on the evaluation of the indoor climate in the big lecture hall. Providing the optimal parameters of the thermal comfort and the CO2 concentration is immensely important for the students in the interiors of a university. Meeting these parameters is inevitable not only from physiological point of view but also for achieving the desirable students' performance. The high CO2 concentration is related to incorrect and insufficient ventilation in the lecture hall and causes distractibility and feeling of tiredness of students. Experimental measurements were carried out in the winter season in 2016 in the big lecture hall in order to evaluate the thermal comfort and the CO2 concentration. The device Testo 480 was used for the measurements. Obtained values of air temperature, air relative humidity, air velocity, CO2 concentration are presented in the charts. Mechanical ventilation system and operation system of the big university lecture hall were evaluated on the basis of the parameters of the thermal comfort and on the basis of the CO2 concentration. Based on the findings, design recommendations for new big university lecture halls are derived. Furthermore, there are presented recommendations how to operate the existing big university lecture halls.

scholarly journals Optimizing air velocity for the underfloor forced ventilation to protect a refrigerated warehouse from frost heaving

2018 ◽  
Vol 38 (3) ◽  
pp. 321-327
Author(s):  
Jingfu Jia ◽  
Manjin Hao ◽  
Jianhua Zhao
Keyword(s):  
Heat Transfer ◽  
Mathematical Model ◽  
Natural Ventilation ◽  
Ventilation System ◽  
Three Dimensional ◽  
Temperature Fields ◽  
Frost Heave ◽  
Forced Ventilation ◽  
Air Velocity ◽  
Set Up

Forced or natural ventilation is the most common measure of frost heave protection for refrigerated warehouse floor. To optimize air velocity for the underfloor forced ventilation system of refrigerated warehouse, a steady state three-dimensional mathematical model of heat transfer is set up in this paper. The temperature fields of this system are simulated and calculated by CFD software PHOENICS under different air velocity, 1.5m/s, 2.5m/s or 3.5m/s. The results show that the optimized air velocity is 1.5m/s when the tube spacing is 1.5m.

scholarly journals Numerical simulations for the optimisation of ventilation system designed for wine cellars

2019 ◽  
Vol 50 (4) ◽  
pp. 180-190 ◽  
Author(s):  
Enrica Santolini ◽  
Alberto Barbaresi ◽  
Daniele Torreggiani ◽  
Patrizia Tassinari
Keyword(s):  
Natural Ventilation ◽  
Ventilation System ◽  
Climatic Conditions ◽  
Mold Growth ◽  
Critical Factors ◽  
Air Velocity ◽  
Wine Production ◽  
First Case ◽  
Dynamics Modelling ◽  
Optimal Configurations

The wine-ageing process is one of the most important phases of the wine production and it can be considerably affected by the micro-climatic conditions inside the ageing rooms. Underground wine cellars in small-medium wineries are designed with natural ventilation systems, able to maintain optimal indoor condition. However, critical factors emerge, such as mold growth or wine evapo-transpiration, where ventilation proved to be poorly designed, insufficient in the first case or excessive in the second one. The zones around the wooden barrels proved to be the most sensitive and problematic. These areas are the most investigated in terms of temperature and humidity values but surprisingly not in terms of air velocity. In this paper, a ventilation system has been designed and optimised to support the lack of ventilation, by means of computational fluid dynamics modelling. Eight configurations have been performed and analysed, identifying the best two according to the air velocity range. Specific parameters have been defined to appreciate the application limits of each configuration. These parameters can be used as reference for system design in similar studies and applications and can help scholars and professionals to identify the optimal configurations for the implementation and proper placement of the system inside a cellar.

Ventilation of Wind-Permeable Clothed Cylinder Subject to Periodic Swinging Motion: Modeling and Experimentation

2008 ◽  
Vol 130 (9) ◽  
Author(s):  
N. Ghaddar ◽  
K. Ghali ◽  
B. Jreije
Keyword(s):  
Cotton Fabric ◽  
Current Model ◽  
Ventilation Rate ◽  
External Pressure ◽  
Motion Modeling ◽  
Tracer Gas ◽  
Wind Speeds ◽  
Air Speed ◽  
Local Thermal Comfort ◽  
Ventilation Rates

Abstract A theoretical and experimental study has been performed to determine the ventilation induced by swinging motion and external wind for a fabric-covered cylinder of finite length representing a limb. The estimated ventilation rates are important in determining local thermal comfort. A model is developed to estimate the external pressure distribution resulting from the relative wind around the swinging clothed cylinder. A mass balance equation of the microclimate air layer is reduced to a pressure equation assuming laminar flow in axial and angular directions and that the air layer is lumped in the radial direction. The ventilation model predicts the total renewal rate during the swinging cycle. A good agreement was found between the predicted ventilation rates at swinging frequencies between 40rpm and 60rpm and measured values from experiments conducted in a controlled environmental chamber (air velocity is less than 0.05m∕s) and in a low speed wind tunnel (for air speed between 2m∕s and 6m∕s) using the tracer gas method to measure the total ventilation rate induced by the swinging motion of a cylinder covered with a cotton fabric for both closed and open aperture cases. A parametric study using the current model is performed on a cotton fabric to study the effect of wind on ventilation rates for a nonmoving clothed limb at wind speeds ranging from 0.5m∕sto8m∕s, the effect of a swinging limb in stagnant air at frequencies up to 80rpm, and the combined effect of wind and swinging motion on the ventilation rate. For a nonmoving limb, ventilation rate increases with external wind. In the absence of wind, the ventilation rate increases with increased swinging frequency.

Sign in / Sign up

Export Citation Format

Share Document