scholarly journals Enhanced Naproxen Elimination in Water by Catalytic Ozonation Based on NiO Films

Catalysts ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 884
Author(s):  
Claudia M. Aguilar-Melo ◽  
Julia L. Rodríguez ◽  
Isaac Chairez ◽  
Iván Salgado ◽  
J. A. Andraca Adame ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Chemical Vapor ◽  
Parametric Identification ◽  
Reaction Rates ◽  
X Ray ◽  
Mineralization Degree ◽  
The Stability ◽  
Modeling Strategy ◽  
Identification Techniques ◽  
Nio Films

This study evaluates naproxen (NP) degradation efficiency by ozonation using nickel oxide films (NiO(F)) as a catalyst. The NiO films were synthesized by chemical vapor deposition and characterized by X-ray diffraction, scanning electron microscopy, atomic force microscopy and X-ray photoelectron spectroscopy. NP degradation was conducted for 5 min using 10 films of NiO(F) comparing against ozonation using 100 mg/L NiO powder in suspension (NiO(S)) and conventional ozonation (O3-conv). Total organic carbon analysis demonstrated a mineralization degree of 12% with O3-conv, 35% with NiO as powder and 22% with NiO(F) after 60 min of reaction. The films of NiO(F) were sequentially used 4 times in ozonation demonstrating the stability of the synthesized material, as well as its properties as a catalyst for ozonation. A proposed modeling strategy using robust parametric identification techniques allows the comparison of NP decomposition pseudo-monomolecular reaction rates.

Interactions of Ge Atoms with High- ê Oxide Dielectric Surfaces

2005 ◽  
Vol 879 ◽  
Author(s):  
Scott K. Stanley ◽  
John G. Ekerdt
Keyword(s):  
Oxide Layer ◽  
Photoelectron Spectroscopy ◽  
Chemical Vapor ◽  
Temperature Programmed Desorption ◽  
Tungsten Filament ◽  
X Ray ◽  
Dielectric Surfaces ◽  
Temperature Programmed ◽  
The Stability ◽  
Ge Nanocrystals

AbstractGe is deposited on HfO2 surfaces by chemical vapor deposition (CVD) with GeH4. 0.7-1.0 ML GeHx (x = 0-3) is deposited by thermally cracking GeH4 on a hot tungsten filament. Ge oxidation and bonding are studied at 300-1000 K with X-ray photoelectron spectroscopy (XPS). Ge, GeH, GeO, and GeO2 desorption are measured with temperature programmed desorption (TPD) at 400-1000 K. Ge initially reacts with the dielectric forming an oxide layer followed by Ge deposition and formation of nanocrystals in CVD at 870 K. 0.7-1.0 ML GeHx deposited by cracking rapidly forms a contacting oxide layer on HfO2 that is stable from 300-800 K. Ge is fully removed from the HfO2 surface after annealing to 1000 K. These results help explain the stability of Ge nanocrystals in contact with HfO2.

CVD Boron Carbo-Nitride as Pore Sealant for Ultra Low-K Interlayer Dielectrics

2005 ◽  
Vol 863 ◽  
Author(s):  
P. Ryan Fitzpatrick ◽  
Sri Satyanarayana ◽  
Yangming Sun ◽  
John M. White ◽  
John G. Ekerdt
Keyword(s):  
Photoelectron Spectroscopy ◽  
Depth Profiling ◽  
Chemical Vapor ◽  
K Value ◽  
X Ray ◽  
Dimethylamine Borane ◽  
The Stability ◽  
Low K ◽  
Secondary Ion ◽  
Sims Depth Profiling

AbstractBlanket porous methyl silsesquioxane (pMSQ) films on a Si substrate were studied with the intent to seal the pores and prevent penetration of a metallic precursor during barrier deposition. The blanket pMSQ films studied were approximately 220 nm thick and had been etched and ashed. When tantalum pentafluoride (TaF5) is exposed to an unsealed pMSQ sample, X-ray photoelectron spectroscopy (XPS) depth profiling and secondary ion mass spectroscopy (SIMS) depth profiling reveal penetration of Ta into the pores all the way to the pMSQ / Si interface. Boron carbo-nitride films were grown by thermal chemical vapor deposition (CVD) using dimethylamine borane (DMAB) precursor with Ar carrier gas and C2H4 coreactant. These films had a stoichiometry of BC0.9N0.07 and have been shown in a previous study to have a k value as low as 3.8. BC0.9N0.07 films ranging from 1.8 to 40.6 nm were deposited on pMSQ and then exposed to TaF5 gas to determine the extent of Ta penetration into the pMSQ. Ta penetration was determined by XPS depth profiling and sometimes SIMS depth profiling. XPS depth profiling of a TaF5 / 6.3 nm BC0.9N0.07 / pMSQ / Si film stack indicates the attenuation of the Ta signal to < 2 at. % throughout the pMSQ. Backside SIMS of this sample suggests that trace amounts of Ta (< 2 at. %) are due to knock-in by Ar ions used for sputtering. An identical film stack containing 3.9 nm BC0.9N0.07 was also successful at inhibiting Ta penetration even with a 370°C post-TaF5 exposure anneal, suggesting the stability of BC0.9N0.07 to thermal diffusion of Ta. All BC0.9N0.07 films thicker than and including 3.9 nm prevented Ta from penetrating into the pMSQ.

Nitrogen (N2) Implantation to Suppress Growth of Interfacial Oxide in Mocvd Bst and Sputtered Bst Films

1999 ◽  
Vol 567 ◽  
Author(s):  
Renee Nieh ◽  
Wen-Jie Qi ◽  
Yongjoo Jeon ◽  
Byoung Hun Lee ◽  
Aaron Lucas ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Interfacial Layer ◽  
Gate Dielectric ◽  
Nitrogen Concentration ◽  
Chemical Vapor ◽  
Future Generation ◽  
Oxide Thickness ◽  
Layer Growth ◽  
X Ray ◽  
Bst Films

ABSTRACTBa0.5Sr0.5TiO3 (BST) is one of the high-k candidates for replacing SiO2 as the gate dielectric in future generation devices. The biggest obstacle to scaling the equivalent oxide thickness (EOT) of BST is an interfacial layer, SixOy, which forms between BST and Si. Nitrogen (N2) implantation into the Si substrate has been proposed to reduce the growth of this interfacial layer. In this study, capacitors (Pt/BST/Si) were fabricated by depositing thin BST films (50Å) onto N2 implanted Si in order to evaluate the effects of implant dose and annealing conditions on EOT. It was found that N2 implantation reduced the EOT of RF magnetron sputtered and Metal Oxide Chemical Vapor Deposition (MOCVD) BST films by ∼20% and ∼33%, respectively. For sputtered BST, an implant dose of 1×1014cm−;2 provided sufficient nitrogen concentration without residual implant damage after annealing. X-ray photoelectron spectroscopy data confirmed that the reduction in EOT is due to a reduction in the interfacial layer growth. X-ray diffraction spectra revealed typical polycrystalline structure with (111) and (200) preferential orientations for both films. Leakage for these 50Å BST films is on the order of 10−8 to 10−5 A/cm2—lower than oxynitrides with comparable EOTs.

scholarly journals Optical Constant and Conformality Analysis of SiO2 Thin Films Deposited on Linear Array Microstructure Substrate by PECVD

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 510
Author(s):  
Yongqiang Pan ◽  
Huan Liu ◽  
Zhuoman Wang ◽  
Jinmei Jia ◽  
Jijie Zhao
Keyword(s):  
Thin Films ◽  
Film Thickness ◽  
Deposition Rate ◽  
Optical Constant ◽  
Photoelectron Spectroscopy ◽  
Linear Array ◽  
Chemical Vapor ◽  
Rf Plasma ◽  
X Ray ◽  
Sio2 Thin Film

SiO2 thin films are deposited by radio frequency (RF) plasma-enhanced chemical vapor deposition (PECVD) technique using SiH4 and N2O as precursor gases. The stoichiometry of SiO2 thin films is determined by the X-ray photoelectron spectroscopy (XPS), and the optical constant n and k are obtained by using variable angle spectroscopic ellipsometer (VASE) in the spectral range 380–1600 nm. The refractive index and extinction coefficient of the deposited SiO2 thin films at 500 nm are 1.464 and 0.0069, respectively. The deposition rate of SiO2 thin films is controlled by changing the reaction pressure. The effects of deposition rate, film thickness, and microstructure size on the conformality of SiO2 thin films are studied. The conformality of SiO2 thin films increases from 0.68 to 0.91, with the increase of deposition rate of the SiO2 thin film from 20.84 to 41.92 nm/min. The conformality of SiO2 thin films decreases with the increase of film thickness, and the higher the step height, the smaller the conformality of SiO2 thin films.

High Quality GaAs Mis Diodes With Very Low Surface State Density

1990 ◽  
Vol 209 ◽  
Author(s):  
Yoshihisa Fujisaki ◽  
Sumiko Sakai ◽  
Saburo Ataka ◽  
Kenji Shibata
Keyword(s):  
Chemical Vapor Deposition ◽  
Density Of States ◽  
Vapor Deposition ◽  
Photoelectron Spectroscopy ◽  
Chemical Vapor ◽  
State Density ◽  
High Quality ◽  
Metal Insulator ◽  
X Ray ◽  
Mis Devices

ABSTRACTHigh quality GaAs/SiO2 MIS( Metal Insulator Semiconductor ) diodes were fabricated using (NH4)2S treatment and photo-assisted CVD( Chemical Vapor Deposition ). The density of states at the GaAs and SiO2 interface is the order of 1011 cm-2eV-1 throughout the forbidden energy range, which is smaller by the order of two than that of the MIS devices made by the conventional CVD process. The mechanism attributable to the interface improvement was investigated through XPS( X-ray Photoelectron Spectroscopy ) analyses.

Influence of Thermal Treatments on the Chemistry and Self-Assembly of Ge Nanoparticles on SiO2 Surfaces

2004 ◽  
Vol 830 ◽  
Author(s):  
Scott K. Stanley ◽  
Shawn S. Coffee ◽  
John G. Ekerdt
Keyword(s):  
Photoelectron Spectroscopy ◽  
Self Assembly ◽  
Chemical Vapor ◽  
Thermal Treatments ◽  
X Ray ◽  
Agglomeration Process ◽  
Oxide Substrate ◽  
Temperature Programmed ◽  
Hot Filament ◽  
Substrate Temperatures

ABSTRACTGeH4 is thermally cracked over a hot filament depositing 0.7–15 ML Ge onto 2–7 nm SiO2/Si(100) at substrate temperatures of 300–970 K. Ge, GeHx, GeO, and GeO2 desorption is monitored through temperature programmed desorption in the temperature range 300–1000 K. Ge bonding changes are analyzed during annealing from 300–1000 K with X-ray photoelectron spectroscopy (XPS). Low temperature desorption features are attributed to GeO and GeH4. No GeO2 desorption is observed, but GeO2 decomposition to Ge through high temperature pathways is seen above 700 K. Germanium oxidization results from Ge etching of the oxide substrate, which is demonstrated through XPS. Ge nanoparticle formation on SiO2 is demonstrated using the agglomeration process. With these results, explanations for the difficulties of conventional chemical vapor deposition to produce Ge nanocrystals on SiO2 surfaces are proposed.

Low Temperature Nitridatio of SiO2 Films using a Catalytic-CVD System

2000 ◽  
Vol 611 ◽  
Author(s):  
Akira Izumi ◽  
Hidekazu Sato ◽  
Hideki Matsumura
Keyword(s):  
Chemical Vapor Deposition ◽  
Low Temperature ◽  
Silicon Dioxide ◽  
Vapor Deposition ◽  
Photoelectron Spectroscopy ◽  
Chemical Vapor ◽  
Catalytic Decomposition ◽  
Catalytic Chemical Vapor Deposition ◽  
Sio2 Films ◽  
X Ray

ABSTRACTThis paper reports a procedure for low-temperature nitridation of silicon dioxide (SiO2) surfaces using species produced by catalytic decomposition of NH3 on heated tungsten in catalytic chemical vapor deposition (Cat-CVD) system. The surface of SiO2/Si(100) was nitrided at temperatures as low as 200°C. X-ray photoelectron spectroscopy measurements revealed that incorporated N atoms are bound to Si atoms and O atoms and located top-surface of SiO2.

scholarly journals Carbide-Modified Pd on ZrO2 as Active Phase for CO2-Reforming of Methane—A Model Phase Boundary Approach

Catalysts ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1000
Author(s):  
Norbert Köpfle ◽  
Kevin Ploner ◽  
Peter Lackner ◽  
Thomas Götsch ◽  
Christoph Thurner ◽  
...  
Keyword(s):  
Phase Boundary ◽  
Photoelectron Spectroscopy ◽  
Batch Reactor ◽  
Ambient Pressure ◽  
Composite Layer ◽  
Reaction Rates ◽  
Near Surface ◽  
X Ray ◽  
Zro2 Phase

Starting from subsurface Zr0-doped “inverse” Pd and bulk-intermetallic Pd0Zr0 model catalyst precursors, we investigated the dry reforming reaction of methane (DRM) using synchrotron-based near ambient pressure in-situ X-ray photoelectron spectroscopy (NAP-XPS), in-situ X-ray diffraction and catalytic testing in an ultrahigh-vacuum-compatible recirculating batch reactor cell. Both intermetallic precursors develop a Pd0–ZrO2 phase boundary under realistic DRM conditions, whereby the oxidative segregation of ZrO2 from bulk intermetallic PdxZry leads to a highly active composite layer of carbide-modified Pd0 metal nanoparticles in contact with tetragonal ZrO2. This active state exhibits reaction rates exceeding those of a conventional supported Pd–ZrO2 reference catalyst and its high activity is unambiguously linked to the fast conversion of the highly reactive carbidic/dissolved C-species inside Pd0 toward CO at the Pd/ZrO2 phase boundary, which serves the role of providing efficient CO2 activation sites. In contrast, the near-surface intermetallic precursor decomposes toward ZrO2 islands at the surface of a quasi-infinite Pd0 metal bulk. Strongly delayed Pd carbide accumulation and thus carbon resegregation under reaction conditions leads to a much less active interfacial ZrO2–Pd0 state.

Sign in / Sign up

Export Citation Format

Share Document