scholarly journals Self-Healing UV-Curable Acrylate Coatings for Wood Finishing System, Part 2: Impact of Monomer Structure and Self-Healing Parameters on Self-Healing Efficiency

Coatings ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1328
Author(s):  
Chloé Paquet ◽  
Stephen Brown ◽  
Jolanta E. Klemberg-Sapieha ◽  
Jean-François Morin ◽  
Véronic Landry
Keyword(s):  
Crosslinking Density ◽  
Wood Products ◽  
The Self ◽  
Mechanical Resistance ◽  
Self Healing ◽  
Uv Curable ◽  
Monomer Structure ◽  
Healing Efficiency ◽  
Wood Flooring ◽  
The Impact

Wood is increasingly used in construction for the benefits it brings to occupants and for its ecological aspect. Indoor wood products are frequently subject to mechanical aggressions, their abrasion and scratch resistance thus need to be improved. The coating system ensures the wood surface protection, which is, for wood flooring, a multilayer acrylate UV-curable 100% solid system. To increase the service life of wood flooring, a new property is studied: self-healing. The objective of this study is to observe the impact of monomer structure on self-healing efficiency and the effect of self-healing parameters. A previous formulation was developed using hydrogen bond technology to generate the self-healing property. In this paper, the assessment of the formulation and the self-healing parameters’ impact on self-healing efficiency as well as the physicochemical properties are presented. The composition of the monomer part in the formulations was varied, and the effect on the conversion yield (measured by FT-IR), on the Tg and crosslinking density (measured by DMA) and on mechanical resistance (evaluated via hardness pendulum, indentation, and reverse impact) was analyzed. The self-healing efficiency of the coatings was determined by gloss and scratch depth measurements (under constant and progressive load). It was proven that monomers with three acrylate functions bring too much crosslinking, which inhibits the chain mobility necessary to observe self-healing. The presence of the AHPMA monomer in the formulation permits considerably increasing the crosslinking density (CLD) while keeping good self-healing efficiency. It was also observed that the self-healing behavior of the coatings is different according to the damage caused. Indeed, the self-healing results after abrasion and after scratch (under constant or progressive load) are different. In conclusion, it is possible to increase CLD while keeping self-healing behavior until a certain limit and with a linear monomer structure to avoid steric hindrance. Moreover, the selection of the best coatings (the one with the highest self-healing) depends on the damage.

scholarly journals Self-Healing UV Curable Acrylate Coatings for Wood Finishing System, Part 1: Impact of the Formulation on Self-Healing Efficiency

Coatings ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 770
Author(s):  
Chloé Paquet ◽  
Thomas Schmitt ◽  
Jolanta E. Klemberg-Sapieha ◽  
Jean-François Morin ◽  
Véronic Landry
Keyword(s):  
Mechanical Properties ◽  
Scratch Resistance ◽  
The Self ◽  
Cross Linking ◽  
Hydroxyl Groups ◽  
Self Healing ◽  
Hydrogen Binding ◽  
Uv Curable ◽  
Wood Flooring ◽  
Healing Property

In the wood flooring sector, good surface mechanical properties, such as abrasion and scratch resistance, are prerequisite. Surface wood protection is provided by finishing systems. Despite coating improvement, scratches formation on wood flooring is unavoidable. A new approach to increase service life is to confer the self-healing property to the finishing system. The most common coatings used for prefinished wood flooring are acrylate UV curable 100% solids coatings. They usually have good mechanical properties and high cross-linking density. The objective of this study was to develop and evaluate an intrinsic self-healing formulation, which is applicable to wood flooring. For this purpose, acrylate formulations were developed with monomers and oligomers carrying hydroxyl groups. To meet the requirements of wood application, hardness, and polymerization conversion of coatings were evaluated. König pendulum damping tests provide information on coating hardness and flexibility. Results around 80 oscillations is acceptable for UV curable wood sealer. The chemical composition was studied by FT-IR spectroscopy while dynamical mechanical analysis (DMA) was performed to determine glass transition temperature and cross-linking density. The self-healing behavior was evaluated by gloss and scratch depth measurements. The formulation’s composition impacted the hydrogen binding quantity, the conversion, the Tg and the cross-linking density. The (hydroxyethyl)methacrylate (HEMA) monomer provided self-healing and acrylated allophanate oligomer allowed self-healing and cross-linking. This study demonstrated that it is possible to combine high cross-linking density and self-healing property, using components with low steric hindrance.

scholarly journals Self-Healable Biocomposites Crosslinked with a Combination of Silica and Quercetin

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4028
Author(s):  
Olga Olejnik ◽  
Anna Masek ◽  
Małgorzata Iwona Szynkowska-Jóźwik
Keyword(s):  
Natural Rubber ◽  
Healing Process ◽  
Crosslinking Density ◽  
Mechanical Tests ◽  
Epoxidized Natural Rubber ◽  
Self Healing ◽  
Human Beings ◽  
Healing Efficiency ◽  
Before And After ◽  
The Impact

In this publication, novel bio-based composites made of epoxidized natural rubber with 50 mol% of epoxidation (ENR-50) are presented. The obtained materials, partially cured with a totally environmentally friendly crosslinking system consisting of natural ingredients, including quercetin and silica, exhibit a self-healing ability resulting from the self-adhesion of ENR-50 and reversible physical forces between the curing agent and the matrix. The impact of natural components on the crosslinking effect in uncured ENR-50 matrix was analyzed based on rheometric measurements, mechanical tests and crosslinking density. The partially crosslinked samples were next cut into two separate pieces, which were instantly contacted together under a small manual press, left at room temperature for a few days for the healing process to occur and finally retested. The healing efficiency was estimated by measuring mechanical properties before and after the healing process and was also confirmed by photos taken using optical and scanning electron microscope (SEM). According to the results, a combination of silica and quercetin is a totally safe, natural and effective crosslinking system dedicated to epoxidized natural rubber. The novel composites containing ingredients safe for human beings exhibit promising self-healing properties with a healing efficiency of up to 45% without any external stimuli and stand a chance of becoming innovative biomedical materials.

scholarly journals The Effect of Superabsorbent Polymers on the Microstructure and Self-Healing Properties of Cementitious-Based Composite Materials

2021 ◽  
Vol 11 (2) ◽  
pp. 700
Author(s):  
Irene A. Kanellopoulou ◽  
Ioannis A. Kartsonakis ◽  
Costas A. Charitidis
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Hybrid Structure ◽  
The Self ◽  
Self Healing ◽  
Cementitious Composite ◽  
Superabsorbent Polymers ◽  
Porosity Reduction ◽  
Environment Control ◽  
The Impact

Cementitious structures have prevailed worldwide and are expected to exhibit further growth in the future. Nevertheless, cement cracking is an issue that needs to be addressed in order to enhance structure durability and sustainability especially when exposed to aggressive environments. The purpose of this work was to examine the impact of the Superabsorbent Polymers (SAPs) incorporation into cementitious composite materials (mortars) with respect to their structure (hybrid structure consisting of organic core—inorganic shell) and evaluate the microstructure and self-healing properties of the obtained mortars. The applied SAPs were tailored to maintain their functionality in the cementitious environment. Control and mortar/SAPs specimens with two different SAPs concentrations (1 and 2% bwoc) were molded and their mechanical properties were determined according to EN 196-1, while their microstructure and self-healing behavior were evaluated via microCT. Compressive strength, a key property for mortars, which often degrades with SAPs incorporation, in this work, practically remained intact for all specimens. This is coherent with the porosity reduction and the narrower range of pore size distribution for the mortar/SAPs specimens as determined via microCT. Moreover, the self-healing behavior of mortar-SAPs specimens was enhanced up to 60% compared to control specimens. Conclusively, the overall SAPs functionality in cementitious-based materials was optimized.

scholarly journals Numerical Studies of the Effects of Water Capsules on Self-Healing Efficiency and Mechanical Properties in Cementitious Materials

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Haoliang Huang ◽  
Guang Ye
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Cementitious Materials ◽  
Self Healing ◽  
Negative Effects ◽  
Numerical Studies ◽  
Healing Efficiency ◽  
The Impact ◽  
Positive Effect

In this research, self-healing due to further hydration of unhydrated cement particles is taken as an example for investigating the effects of capsules on the self-healing efficiency and mechanical properties of cementitious materials. The efficiency of supply of water by using capsules as a function of capsule dosages and sizes was determined numerically. By knowing the amount of water supplied via capsules, the efficiency of self-healing due to further hydration of unhydrated cement was quantified. In addition, the impact of capsules on mechanical properties was investigated numerically. The amount of released water increases with the dosage of capsules at different slops as the size of capsules varies. Concerning the best efficiency of self-healing, the optimizing size of capsules is 6.5 mm for capsule dosages of 3%, 5%, and 7%, respectively. Both elastic modulus and tensile strength of cementitious materials decrease with the increase of capsule. The decreasing tendency of tensile strength is larger than that of elastic modulus. However, it was found that the increase of positive effect (the capacity of inducing self-healing) of capsules is larger than that of negative effects (decreasing mechanical properties) when the dosage of capsules increases.

Effect of Using Magnesium Acetate on the Self-Healing Efficiency of Hydrogel-Encapsulated Bacteria in Concrete

2021 ◽  
Author(s):  
Ricardo Hungria ◽  
Momen Mousa ◽  
Marwa Hassan ◽  
Omar Omar ◽  
Andrea Gavilanes ◽  
...  
Keyword(s):  
The Self ◽  
Magnesium Acetate ◽  
Self Healing ◽  
Healing Efficiency ◽  
Encapsulated Bacteria

scholarly journals Design of self-healing catalysts for aircraft application

2018 ◽  
Vol 9 (6) ◽  
pp. 723-736 ◽  
Author(s):  
Elisa Calabrese ◽  
Pasquale Longo ◽  
Carlo Naddeo ◽  
Annaluisa Mariconda ◽  
Luigi Vertuccio ◽  
...  
Keyword(s):  
Ruthenium Catalysts ◽  
The Self ◽  
Self Healing ◽  
Catalytic Systems ◽  
Content Type ◽  
Aerospace Applications ◽  
Healing Efficiency ◽  
Relevant Role ◽  
Aircraft Application

PurposeThe purpose of this paper is to highlight the relevant role of the stereochemistry of two Ruthenium catalysts on the self-healing efficiency of aeronautical resins.Design/methodology/approachHere, a very detailed evaluation on the stereochemistry of two new ruthenium catalysts evidences the crucial role of the spatial orientation of phenyl groups in the N-heterocyclic carbene ligands in determining the temperature range within the curing cycles is feasible without deactivating the self-healing mechanisms (ring-opening metathesis polymerization reactions) inside the thermosetting resin. The exceptional activity and thermal stability of the HG2MesPhSyncatalyst, with the syn orientation of phenyl groups, highlight the relevant potentiality and the future perspectives of this complex for the activation of the self-healing function in aeronautical resins.FindingsThe HG2MesPhSyncomplex, with the syn orientation of the phenyl groups, is able to activate metathesis reactions within the highly reactive environment of the epoxy thermosetting resins, cured up to 180°C, while the other stereoisomer, with the anti-orientation of the phenyl groups, does not preserve its catalytic activity in these conditions.Originality/valueIn this paper, a comparison between the self-healing functionality of two catalytic systems has been performed, using metathesis tests and FTIR spectroscopy. In the field of the design of catalytic systems for self-healing structural materials, a very relevant result has been found: a slight difference in the molecular stereochemistry plays a key role in the development of self-healing materials for aeronautical and aerospace applications.

Effects of the Self-Healing Microcapsules on the Impact Property of Polymer Composite Gear

2011 ◽  
Vol 66-68 ◽  
pp. 683-687 ◽  
Author(s):  
Li Zhang ◽  
Yan Jue Gong ◽  
Shuo Zhang
Keyword(s):  
Glass Fiber ◽  
Polymer Composite ◽  
The Self ◽  
Impact Property ◽  
Self Healing ◽  
Fiber Reinforced ◽  
Mechanical Impact ◽  
Glass Fiber Reinforced ◽  
The Impact

By designing the different formulations of the composites and adopting optimized technology including extrusion and molding, the effects of the Micro-capsules on the properties of nylon composites are analyzed by the impact property test. The mechanical impact property of the glass fiber reinforced nylon composites is influenced little if the content of the self-healing microcapsules added is less than 3.5%, and the technology of self-healing microcapsules used in the polymer composite gear is feasible.

The effects of textile reinforcements on the protective properties of self-healing polymers intended for safety gloves

2020 ◽  
Vol 90 (17-18) ◽  
pp. 1974-1986
Author(s):  
Emilia Irzmańska ◽  
Anna Bacciarelli-Ulacha ◽  
Agnieszka Adamus-Włodarczyk ◽  
Anna Strąkowska
Keyword(s):  
Healing Process ◽  
Polymeric Composite ◽  
Polymeric Materials ◽  
Economic Loss ◽  
The Self ◽  
Raw Material ◽  
Protective Equipment ◽  
Self Healing ◽  
Hybrid Molecules ◽  
The Impact

In the environment where glove material is exposed to harmful chemicals, hazards related to faster penetration of dangerous substances into the glove interior may cause microdamage. One of the solutions to overcome this problem is to use the self-healing polymeric materials that can minimize economic loss and accidents in the workplace. The current work aims to present the impact of different types of textile reinforcement on the effectiveness and efficiency of the self-healing process of methyl vinyl silicone rubber containing hybrid molecules with an inorganic silsesquioxane intended for use on all-rubber gloves. Three knitted fabrics with a similar structure and differentiated raw material composition were selected: polyamide, cotton–polyamide, and cotton. Evaluation of the self-healing process of the elastomeric composite to personal protective equipment was performed. For this purpose the assessment of the surface morphology of materials has been performed before and after the self-healing process. The implementation of knitted fabric into the polymeric composite in the tested samples allowed us to obtain the best results in all tests. The studied composite samples exhibited an increased resistance to three types of damage: penetration, abrasion and puncture. The samples also underwent the self-healing processes and regeneration after a proper conditioning period. Thus, the obtained results confirmed the possibility of using tested elastomeric composites in the construction of protective gloves and showed an effectivity of the self-healing process for the long-term usage of that protective equipment.

scholarly journals Healing Performance of a Self-Healing Protective Coating According to Damage Width

Coatings ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 543
Author(s):  
Dong-Min Kim ◽  
Junseo Lee ◽  
Ju-Young Choi ◽  
Seung-Won Jin ◽  
Kyeong-Nam Nam ◽  
...  
Keyword(s):  
Protective Coating ◽  
Coating Thickness ◽  
Chloride Ion ◽  
The Self ◽  
Self Healing ◽  
Chloride Ion Penetration ◽  
Healing Efficiency ◽  
Sem Study ◽  
Capsule Size ◽  
Ion Penetration

Although self-healing protective coatings have been widely studied, systematic research on healing performance of the coating according to damage width has been rare. In addition, there has been rare reports of self-healing of the protective coating having damage width wider than 100 µm. In this study, self-healing performance of a microcapsule type self-healing protective coating on cement mortar was studied for the coating with damage width of 100–300 µm. The effect of capsule-loading (20 wt%, 30 wt% and 40 wt%), capsule size (65-, 102- and 135-µm-mean diameter) and coating thickness (50-, 80- and 100-µm-thick undercoating) on healing efficiency was investigated by water sorptivity test. Accelerated carbonation test, chloride ion penetration test and scanning electron microscope (SEM) study were conducted for the self-healing coating with a 300-µm-wide damage. Healing efficiency of the self-healing coating decreased with increasing damage width. As capsule-loading, capsule size or coating thickness increased, healing efficiency of the self-healing coating increased. Healing efficiency of 76% or higher was achieved using the self-healing coating with a 300-µm-wide scratch. The self-healing coating with a 200-µm-wide crack showed healing efficiency of 70% or higher. The self-healing coating having a 300-µm-wide scratch showed effective protection of the substrate mortar from carbonation and chloride ion penetration, which was supported by SEM study.

Sign in / Sign up

Export Citation Format

Share Document