scholarly journals A Study on the Corrosion Resistance of Hydrophobic Coatings on 65Mn Steel

Coatings ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1399
Author(s):  
Yufen Zhang ◽  
Qingcheng Du ◽  
Tiegui Lin ◽  
Shawei Tang ◽  
Jin Hu
Keyword(s):  
Contact Angle ◽  
Corrosion Resistance ◽  
Phase Composition ◽  
Water Contact Angle ◽  
Corrosion Behavior ◽  
Direct Current ◽  
Deposition Time ◽  
Nacl Solution ◽  
Water Contact ◽  
Hydrophobic Coatings

Calcium stearate hydrophobic coatings with a hierarchical micro/nanostructure were prepared on 65Mn steel using direct current electrodeposition. The deposition time has a visible influence on the morphology, surface wettability and thickness of the coatings, but little effect on the phase composition. The corrosion behavior of the coated samples in 3.5 wt.% NaCl solution was also investigated. The prepared coatings at different deposition times show different corrosion resistance. The coating fabricated at 30 min has the best corrosion resistance due to the highest water contact angle and thicker coating.

Fabrication of Hydrophobic Surfaces and its Electrochemical Research on Copronickel B30

2011 ◽  
Vol 347-353 ◽  
pp. 560-563 ◽  
Author(s):  
Qun Jie Xu ◽  
Xi Hong Cai ◽  
Hong Yun ◽  
Xian Qin Deng
Keyword(s):  
Contact Angle ◽  
Corrosion Resistance ◽  
Stearic Acid ◽  
Inhibition Efficiency ◽  
Electrochemical Techniques ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Nacl Solution ◽  
Film Properties ◽  
Water Contact

A novel hydrophobic film was prepared by Stearic acid (SA) chemically adsorbed onto the cupronickel B30 surface. The film properties were characterized by means of water contact angle measurement and electrochemical techniques. The results indicate that the structure of the adsorbed film is hydrophobic, and the contact angle is 113.82° for water. AC impedance and polarization curve measurements show that the corrosion resistance of cupronickel B30 modified by stearic acid is improved remarkably, and the inhibition efficiency reached 66.85%. After hydrophobic modified by stearic acid, the inhibition efficiency could reach 88.85% in 3% NaCl solution with the concentration of 0.1 g/L Na2WO4.

A superrobust superhydrophobic PSU composite coating with self-cleaning properties, wear resistance and corrosion resistance

RSC Advances ◽  
2016 ◽  
Vol 6 (13) ◽  
pp. 10930-10937 ◽  
Author(s):  
Huaiyuan Wang ◽  
Xiguang Zhang ◽  
Zhanjian Liu ◽  
Yixing Zhu ◽  
Shiqi Wu ◽  
...  
Keyword(s):  
Contact Angle ◽  
Wear Resistance ◽  
Corrosion Resistance ◽  
Composite Coating ◽  
Water Contact Angle ◽  
Thermal Spraying ◽  
High Water ◽  
Water Contact ◽  
Slide Angle ◽  
Spraying Method

In this study, a superhydrophobic polysulfone (PSU) composite coating with a high water contact angle (WCA) of 159° and a low slide angle (SA) of only 3.5° has been fabricated through a simple thermal spraying method.

scholarly journals Fabrication and Corrosion Resistance of Superhydrophobic Hydroxide Zinc Carbonate Film on Aluminum Substrates

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Jin Liang ◽  
Yunchu Hu ◽  
Yiqiang Wu ◽  
Hong Chen
Keyword(s):  
Contact Angle ◽  
Corrosion Resistance ◽  
Water Contact Angle ◽  
Superhydrophobic Surface ◽  
Aluminum Substrate ◽  
Morphological Observation ◽  
Water Contact ◽  
Zinc Carbonate ◽  
Eis Measurements ◽  
Aluminum Substrates

Superhydrophobic hydroxide zinc carbonate (HZC) films were fabricated on aluminum substrate through a convenient in situ deposition process. Firstly, HZC films with different morphologies were deposited on aluminum substrates through immersing the aluminum substrates perpendicularly into aqueous solution containing zinc nitrate hexahydrate and urea. Secondly, the films were then modified with fluoroalkylsilane (FAS: CH3(CF2)6(CH2)3Si(OCH3)3) molecules by immersing in absolute ethanol solution containing FAS. The morphologies, hydrophobicity, chemical compositions, and bonding states of the films were analyzed by scanning electron microscopy (SEM), water contact angle measurement (CA), Fourier transform infrared spectrometer (FTIR), and X-ray photoelectron spectroscopy (XPS), respectively. It was shown by surface morphological observation that HZC films displayed different microstructures such as microporous structure, rose petal-like structure, block-shaped structure, and pinecone-like structure by altering the deposition condition. A highest water contact angle of 156.2° was obtained after FAS modification. Moreover, the corrosion resistance of the superhydrophobic surface on aluminum substrate was investigated using electrochemical impedance spectroscopy (EIS) measurements. The EIS measurements’ results revealed that the superhydrophobic surface considerably improved the corrosion resistance of aluminum.

scholarly journals Modeling Experimental Parameters for the Fabrication of Multifunctional Surfaces Composed of Electrospun PCL/ZnO-NPs Nanofibers

Polymers ◽  
2021 ◽  
Vol 13 (24) ◽  
pp. 4312
Author(s):  
Pedro J. Rivero ◽  
Juan P. Fuertes ◽  
Adrián Vicente ◽  
Álvaro Mata ◽  
José F. Palacio ◽  
...  
Keyword(s):  
Contact Angle ◽  
Corrosion Resistance ◽  
Surface Morphology ◽  
Water Contact Angle ◽  
Solution Concentration ◽  
Electrospun Fibers ◽  
Operational Parameters ◽  
Zno Nps ◽  
Electrospinning Technique ◽  
Water Contact

In this work, a one-step electrospinning technique has been implemented for the design and development of functional surfaces with a desired morphology in terms of wettability and corrosion resistance by using polycaprolactone (PCL) and zinc oxide nanoparticles (ZnO NPs). The surface morphology has been characterized by confocal microscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM) and water contact angle (WCA), whereas the corrosion resistance has been evaluated by Tafel polarization curves. Strict control over the input operational parameters (applied voltage, feeding rate, distance tip to collector), PCL solution concentration and amount of ZnO NPs have been analyzed in depth by showing their key role in the final surface properties. With this goal in mind, a design of experiment (DoE) has been performed in order to evaluate the optimal coating morphology in terms of fiber diameter, surface roughness (Ra), water contact angle (WCA) and corrosion rate. It has been demonstrated that the solution concentration has a significant effect on the resultant electrospun structure obtained on the collector with the formation of beaded fibers with a higher WCA value in comparison with uniform bead-free fibers (dry polymer deposition or fiber-merging aspect). In addition, the presence of ZnO NPs distributed within the electrospun fibers also plays a key role in corrosion resistance, although it also leads to a decrease in the WCA. Finally, this is the first time that an exhaustive analysis by using DoE has been evaluated for PCL/ZnO electrospun fibers with the aim to optimize the surface morphology with the better performance in terms of corrosion resistance and wettability.

Long-Term Stable Metal Organic Framework (MOF) Based Mixed Matrix Membranes for Ultrafiltration

2020 ◽  
Author(s):  
Muayad Al-shaeli ◽  
Stefan J. D. Smith ◽  
Shanxue Jiang ◽  
Huanting Wang ◽  
Kaisong Zhang ◽  
...  
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Mixed Matrix Membranes ◽  
Recovery Ratio ◽  
Mixed Matrix ◽  
Water Contact ◽  
Membrane Performance ◽  
Metal Organic ◽  
Matrix Membranes

<p>In this study, novel <a>mixed matrix polyethersulfone (PES) membranes</a> were synthesized by using two different kinds of metal organic frameworks (MOFs), namely UiO-66 and UiO-66-NH<sub>2</sub>. The composite membranes were characterised by SEM, EDX, FTIR, PXRD, water contact angle, porosity, pore size, etc. Membrane performance was investigated by water permeation flux, flux recovery ratio, fouling resistance and anti-fouling performance. The stability test was also conducted for the prepared mixed matrix membranes. A higher reduction in the water contact angle was observed after adding both MOFs to the PES and sulfonated PES membranes compared to pristine PES membranes. An enhancement in membrane performance was observed by embedding the MOF into PES membrane matrix, which may be attributed to the super-hydrophilic porous structure of UiO-66-NH<sub>2</sub> nanoparticles and hydrophilic structure of UiO-66 nanoparticles that could accelerate the exchange rate between solvent and non-solvent during the phase inversion process. By adding the MOFs into PES matrix, the flux recovery ratio was increased greatly (more than 99% for most mixed matrix membranes). The mixed matrix membranes showed higher resistance to protein adsorption compared to pristine PES membranes. After immersing the membranes in water for 3 months, 6 months and 12 months, both MOFs were stable and retained their structure. This study indicates that UiO-66 and UiO-66-NH<sub>2</sub> are great candidates for designing long-term stable mixed matrix membranes with higher anti-fouling performance.</p>

scholarly journals Surface modification of PMMA polymer and its composites with PC61BM fullerene derivative using an atmospheric pressure microwave argon plasma sheet

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Andrzej Sikora ◽  
Dariusz Czylkowski ◽  
Bartosz Hrycak ◽  
Magdalena Moczała-Dusanowska ◽  
Marcin Łapiński ◽  
...  
Keyword(s):  
Contact Angle ◽  
Surface Modification ◽  
Chemical Composition ◽  
Water Contact Angle ◽  
Plasma Sheet ◽  
Atmospheric Pressure ◽  
Argon Plasma ◽  
Fullerene Derivative ◽  
Water Contact ◽  
Pmma Polymer

AbstractThis paper presents the results of experimental investigations of the plasma surface modification of a poly(methyl methacrylate) (PMMA) polymer and PMMA composites with a [6,6]-phenyl-C61-butyric acid methyl ester fullerene derivative (PC61BM). An atmospheric pressure microwave (2.45 GHz) argon plasma sheet was used. The experimental parameters were: an argon (Ar) flow rate (up to 20 NL/min), microwave power (up to 530 W), number of plasma scans (up to 3) and, the kind of treated material. In order to assess the plasma effect, the possible changes in the wettability, roughness, chemical composition, and mechanical properties of the plasma-treated samples’ surfaces were evaluated by water contact angle goniometry (WCA), atomic force microscopy (AFM), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). The best result concerning the water contact angle reduction was from 83° to 29.7° for the PMMA material. The ageing studies of the PMMA plasma-modified surface showed long term (100 h) improved wettability. As a result of plasma treating, changes in the samples surface roughness parameters were observed, however their dependence on the number of plasma scans is irregular. The ATR-FTIR spectra of the PMMA plasma-treated surfaces showed only slight changes in comparison with the spectra of an untreated sample. The more significant differences were demonstrated by XPS measurements indicating the surface chemical composition changes after plasma treatment and revealing the oxygen to carbon ratio increase from 0.1 to 0.4.

scholarly journals Effect of Fluid Flow on the Corrosion Performance of as-Cast and Heat-Treated Nickel Aluminum Bronze Alloy (UNS C95800) in Saline Solution

2021 ◽  
Vol 2 (1) ◽  
pp. 61-77
Author(s):  
Hamid Reza Jafari ◽  
Ali Davoodi ◽  
Saman Hosseinpour
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Flow Rate ◽  
Solution Temperature ◽  
Aluminum Bronze ◽  
Nickel Aluminum ◽  
Nacl Solution ◽  
Flow Conditions ◽  
Heat Treated ◽  
Nickel Aluminum Bronze

In this work, the corrosion behavior and surface reactivity of as-cast and heat-treated nickel aluminum bronze casting alloy (UNS C95800) in 3.5 wt% NaCl solution is investigated under stagnant and flow conditions. Increasing flow rate conditions are simulated using a rotating disk electrode from 0 to 9000 revolutions per minute (rpm). Optical micrographs confirm the decrease in the phase fraction of corrosion-sensitive β phase in the microstructure of C95800 after annealing, which, in turn, enhances the corrosion resistance of the alloy. Electrochemical studies including open circuit potentiometry, potentiodynamic polarization, and electrochemical impedance spectroscopy are performed to assess the effect of flow rate and heat treatment on the corrosion of samples at 25 and 40 °C in 3.5 wt% NaCl solution. For both as-cast and heat-treated samples, increasing the flow rate (i.e., electrode rotating rate) linearly reduces the corrosion resistance, indicating that the metal dissolution rate is significantly affected by hydrodynamic flow. Increasing the solution temperature negatively impacts the corrosion behavior of the as-cast and heat-treated samples at all flow conditions.

scholarly journals Physicochemical Properties and Biocompatibility of Electrospun Polycaprolactone/Gelatin Nanofibers

2021 ◽  
Vol 18 (9) ◽  
pp. 4764
Author(s):  
Wei Lee Lim ◽  
Shiplu Roy Chowdhury ◽  
Min Hwei Ng ◽  
Jia Xian Law
Keyword(s):  
Contact Angle ◽  
Physicochemical Properties ◽  
Water Contact Angle ◽  
Ligament Injury ◽  
Great Promise ◽  
Composition Analysis ◽  
Water Contact ◽  
Tenogenic Differentiation ◽  
Good Biocompatibility ◽  
Tissue Grafts

Tissue-engineered substitutes have shown great promise as a potential replacement for current tissue grafts to treat tendon/ligament injury. Herein, we have fabricated aligned polycaprolactone (PCL) and gelatin (GT) nanofibers and further evaluated their physicochemical properties and biocompatibility. PCL and GT were mixed at a ratio of 100:0, 70:30, 50:50, 30:70, 0:100, and electrospun to generate aligned nanofibers. The PCL/GT nanofibers were assessed to determine the diameter, alignment, water contact angle, degradation, and surface chemical analysis. The effects on cells were evaluated through Wharton’s jelly-derived mesenchymal stem cell (WJ-MSC) viability, alignment and tenogenic differentiation. The PCL/GT nanofibers were aligned and had a mean fiber diameter within 200–800 nm. Increasing the GT concentration reduced the water contact angle of the nanofibers. GT nanofibers alone degraded fastest, observed only within 2 days. Chemical composition analysis confirmed the presence of PCL and GT in the nanofibers. The WJ-MSCs were aligned and remained viable after 7 days with the PCL/GT nanofibers. Additionally, the PCL/GT nanofibers supported tenogenic differentiation of WJ-MSCs. The fabricated PCL/GT nanofibers have a diameter that closely resembles the native tissue’s collagen fibrils and have good biocompatibility. Thus, our study demonstrated the suitability of PCL/GT nanofibers for tendon/ligament tissue engineering applications.

Sign in / Sign up

Export Citation Format

Share Document