Fabrication of Hydrophobic Surfaces and its Electrochemical Research on Copronickel B30

2011 ◽  
Vol 347-353 ◽  
pp. 560-563 ◽  
Author(s):  
Qun Jie Xu ◽  
Xi Hong Cai ◽  
Hong Yun ◽  
Xian Qin Deng
Keyword(s):  
Contact Angle ◽  
Corrosion Resistance ◽  
Stearic Acid ◽  
Inhibition Efficiency ◽  
Electrochemical Techniques ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Nacl Solution ◽  
Film Properties ◽  
Water Contact

A novel hydrophobic film was prepared by Stearic acid (SA) chemically adsorbed onto the cupronickel B30 surface. The film properties were characterized by means of water contact angle measurement and electrochemical techniques. The results indicate that the structure of the adsorbed film is hydrophobic, and the contact angle is 113.82° for water. AC impedance and polarization curve measurements show that the corrosion resistance of cupronickel B30 modified by stearic acid is improved remarkably, and the inhibition efficiency reached 66.85%. After hydrophobic modified by stearic acid, the inhibition efficiency could reach 88.85% in 3% NaCl solution with the concentration of 0.1 g/L Na2WO4.

scholarly journals Superhydrophobic functionalized cellulosic paper by copper hydroxide nanorods for oils purification

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ahmed S. Belal ◽  
Jehan El Nady ◽  
Azza Shokry ◽  
Shaker Ebrahim ◽  
Moataz Soliman ◽  
...  
Keyword(s):  
Contact Angle ◽  
Filter Paper ◽  
Separation Efficiency ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Absorption Capacity ◽  
Morphological Properties ◽  
Copper Hydroxide ◽  
Immersion Method ◽  
Water Contact

AbstractOily water contamination has been sighted as one of the most global environmental pollution. Herein, copper hydroxide nanorods layer was constructed onto cellulosic filter paper surface cured with polydopamine, Ag nanoparticles, and Cu NPs through immersion method. This work has been aimed to produce a superhydrophobic and superoleophilic cellulosic filter paper. The structure, crystalline, and morphological properties of these modified cellulosic filter paper were investigated. Scanning electron microscope images confirmed that the modified surface was rougher compared with the pristine surface. The contact angle measurement confirmed the hydrophobic nature of these modified surfaces with a water contact angle of 169.7°. The absorption capacity was 8.2 g/g for diesel oil and the separation efficiency was higher than 99%. It was noted that the flux in the case of low viscosity solvent as n-hexane was 9663.5 Lm−2 h−1, while for the viscous oil as diesel was 1452.7 Lm−2 h−1.

Preparation of TiO2–SiO2 Hybrid Nanosols Coated Flame-Retardant Polyester Fabric Possessing Dual Contradictory Characteristics of Superhydrophobicity and Self Cleaning Ability

2020 ◽  
Vol 20 (3) ◽  
pp. 1780-1789 ◽  
Author(s):  
Priyanka Katiyar ◽  
Shraddha Mishra ◽  
Anurag Srivastava ◽  
N. Eswara Prasad
Keyword(s):  
Electron Microscopy ◽  
Contact Angle ◽  
Flame Retardant ◽  
Protective Clothing ◽  
Sol Gel ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Water Contact ◽  
Vis Spectroscopy ◽  
Self Cleaning

TiO2, SiO2 and their hybrid nanocoatings are prepared on inherent flame retardant textile substrates from titanium(IV)iso-proproxide (TTIP) and tetraethoxysilane (TEOS) precursors using a sol–gel process followed by hydrothermal treatment. The coated samples are further functionalized by hexadecyltrimethoxysilane (HDTMS) to impart superhydrophobicity. Sample characterization of the nanosols, nanoparticles and coated samples are investigated using, X-ray diffractometer, transmission electron microscopy, scanning electron microscopy, UV-Vis spectroscopy, contact angle measurement. Stain degradation test under mild UV irradiation shows almost 54% degradation of coffee stain within 4 hours measured by Spectrophotometer. UV-Vis Absorption Spectroscopy demonstrates complete degradation of methyl orange colorant within 3 hours. Hybrid nanosol coated and HDTMS modified inherent flame retardant polyester surfaces show apparent water contact angle as ~145°, which is much closer to proximity of superhydrophobic surfaces. Thus, the novelty of present work is, by using sol–gel technique, a bi-functional textile surface has been developed which qualifies the very specific requirements of protective clothing like self-cleaning property (imparted by TiO2 nanoparticles) and superhydrophobicity (imparted by SiO2 nanoparticles and further surface modification by HDTMS), which are entirely contradictory in nature, in a single fabric itself. Thus developed textile surfaces also possess the other attributes of protective clothing like flame retardancy and air permeability.

Effect of Plasma-Induced Polymerization on Contact Angle of Paper

2011 ◽  
Vol 396-398 ◽  
pp. 1619-1623
Author(s):  
Zhao Ping Song ◽  
Jun Rong Li ◽  
Hui Ning Xiao
Keyword(s):  
Contact Angle ◽  
Photoelectron Spectroscopy ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Polymer Grafting ◽  
Hydrophobic Property ◽  
Cellulose Fibres ◽  
Water Contact ◽  
X Ray ◽  
Factors Associated

Hydrophobic modification of cellulose fibres was conducted by plasma-induced polymer grafting in an attempt to increase the hydrophobicity of paper. Two hydrophobic monomers, i.e., butyl acrylate (BA) and 2-ethylhexyl acrylate (2-EHA) were grafted on cellulose fibres, induced by atmospheric cold plasma. Various influencing factors associated with the plasma-induced grafting were investigated, including the contact time and reaction temperature with monomers, and the dosage of monomers. Contact-angle measurement, infrared spectrum (IR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM) were used to ascertain the occurrence of the grafting. The results showed that the hydrophobic property of the modified paper sheet was improved significantly after the plasma-induced grafting. The water contact angle on the surface of the paper reached up to higher than125°.

Super-Hydrophobic Surfaces Improve Corrosion Resistance of Fe3Al-Type Intermetallic in Seawater

2008 ◽  
Vol 47-50 ◽  
pp. 173-176 ◽  
Author(s):  
Tao Liu ◽  
Kin Tak Lau ◽  
Shou Gang Chen ◽  
Sha Cheng ◽  
Yan Sheng Yin
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Contact Angle ◽  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Hydrophobic Surface ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Atomic Force ◽  
Scanning Electron

A novel super-hydrophobic film was prepared by myristic acid (CH3(CH2)12COOH) chemically adsorbed onto the polyethyleneimine (PEI) coated Fe3Al-type intermetallic wafer. The film character and structure were probed with contact angle measurement, scanning electron microscopy (SEM) and atomic force microscope (AFM). The results suggest that the structure of the film is similar to lotus and the seawater contact angle is larger than 150◦. Moreover, the corrosion resistances of untreated and modified samples in seawater were investigated by electrochemical impedance spectroscopy (EIS). Experimental results show that the corrosion rate of Fe3Al-type intermetallic with super-hydrophobic surface decreases dramatically because of its special microstructure.

Picoliter Water Contact Angle Measurement on Polymers

Langmuir ◽  
2007 ◽  
Vol 23 (13) ◽  
pp. 6875-6878 ◽  
Author(s):  
Michael Taylor ◽  
Andrew J. Urquhart ◽  
Mischa Zelzer ◽  
Martyn C. Davies ◽  
Morgan R. Alexander
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Water Contact ◽  
Water Contact Angle Measurement

SYNTHESIS AND CHARACTERIZATION OF SUPERHYDROPHOBIC ZnO HIERARCHICAL STRUCTURES

NANO ◽  
2011 ◽  
Vol 06 (03) ◽  
pp. 265-269 ◽  
Author(s):  
QUNBING ZHANG ◽  
SHIHE CAO ◽  
JUN WANG
Keyword(s):  
Contact Angle ◽  
Hydrothermal Process ◽  
Hierarchical Structures ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Zno Films ◽  
Water Contact ◽  
Simple Method ◽  
Microscopy Images

ZnO films with well-aligned hierarchical structures have been successfully synthesized at moderate temperatures using a simple catalyst-free hydrothermal process. The synthesized ZnO films are found to be single-phase, with a hexagonal wurtzite-type structure. Scanning electron microscopy images show that the well-aligned hierarchical structures are assembled with interlaced parallel sheets grown on the (400) silica surface. The water contact angle measurement indicates that the water on the films has a contact angle of about 156.3°. This clearly demonstrates that the ZnO films synthesized by this simple method have superhydrophobic properties and may be important for applications in self-cleaning surfaces, biology, and so on.

Improvement in Corrosion and Adhesion Resistance of a Al2O3-CeO2 Nanocomposite Coating on the Aluminum Alloy AA6061 via Surface Pretreatment

2015 ◽  
Vol 1120-1121 ◽  
pp. 677-688
Author(s):  
Yu Mei Han ◽  
Masoud Farzaneh
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Contact Angle Measurement ◽  
Nanocomposite Coating ◽  
Angle Measurement ◽  
Boiling Water ◽  
Water Contact ◽  
Surface Pretreatment ◽  
Pretreatment Method ◽  
Koh Etching

In the present study, a surface pretreatment method consisting of KOH etching followed by oxide thickening in boiling water was used to improve the corrosion and adhesion resistance of the coating. The coating morphology on non-pretreated and pretreated Al substrates was characterized by means of scanning electron microscopy (SEM), atomic force microscopy (AFM) and water contact angle measurement. FT-IR spectra was obtained by Fourier transform infrared spectrometer. The corrosion resistance of the coating in 3.5 wt.% NaCl solution was evaluated with potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS) techniques. The adhesion resistance of the coating was tested using ISO-2409 standard. Results show that KOH etching followed by oxide thickening in boiling water can effectively improves the corrosion resistance and durability of the coating. Besides, this surface pretreatment method can also improve significantly the adhesion resistance of the coating.

scholarly journals Simple method of fabrication of hydrophobic coatings for polyurethanes

2011 ◽  
Vol 9 (6) ◽  
pp. 1039-1045 ◽  
Author(s):  
Beata Butruk ◽  
Paulina Ziętek ◽  
Tomasz Ciach
Keyword(s):  
Contact Angle ◽  
High Efficiency ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Acoustic Microscopy ◽  
Water Contact ◽  
Simple Method ◽  
Hydrophobic Coatings ◽  
Grafting Reaction

AbstractThe aim of this study was to develop a method of manufacturing versatile hydrophobic coatings for polymers. Authors present a simple technique of polyurethane (PU) surface modification with covalently attached silicones (PDMS) or fluorocarbons (PFC). Diisocyanates were applied as linker molecules. The obtained coatings were characterized using spectroscopic analysis (FTIR), scanning acoustic microscopy (SAM) and water contact angle measurements. FTIR analysis revealed high efficiency of grafting reaction. The results of contact angle measurement indicated significant increase of hydrophobicity — from 66° (unmodified PU) to 113° (PU grafted with PDMS) and 118° (PU grafted with PFC). Acoustic microscopy analysis confirmed satisfactory homogeneity and smoothness of the fabricated layers. In vitro cell tests revealed non-adherent properties of the surfaces. Both, MTT assay and fluorescence staining confirmed non-cytotoxicity of the coatings, which makes them potential candidates for use in biomedical applications.

Contact Angle Analysis on Glass Based Surface

2014 ◽  
Vol 680 ◽  
pp. 93-96
Author(s):  
Muhammad Hafiz Ab Aziz ◽  
Zaliman Sauli ◽  
Vithyacharan Retnasamy ◽  
Wan Mokhdzani Wan Norhaimi ◽  
Steven Taniselass ◽  
...  
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Hydrophobic Surface ◽  
Soda Lime ◽  
Sample Surface ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Anodic Bonding ◽  
Soda Lime Glass ◽  
Water Contact

This paper reports on the contact angle measurement analysis on a glass based surface for anodic bonding process cleaned by three distinct cleaning processes. The three types of glass based surface used were silica, pyrex, and soda lime glass. The three cleaning solutions tested in this experiment were RCA, piranha and acetone. Water Droplet Test (WDT) was done to analyze the contact angle of micro droplet on sample surface. It can be done by dropping a droplet of water in constant volume at the fixed height and angle. Only RCA process constantly decreases the contact angle value after cleaning. The compilations of data strongly proved that all samples become hydrophilic after RCA cleaning process. The solid surface is considered hydrophilic when water contact angle is smaller than 90°, and hydrophobic profile if the water contact angle is larger than 90°. Samples which undergo piranha and acetone cleaning did not prove any characteristic of hydrophilic or hydrophobic surface after cleaning.

Sign in / Sign up

Export Citation Format

Share Document