scholarly journals Microstructure and Mechanical Properties of Carbide Reinforced TiC-Based Ultra-High Temperature Ceramics: A Review

Coatings ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1444
Author(s):  
Haobo Mao ◽  
Fuqiang Shen ◽  
Yingyi Zhang ◽  
Jie Wang ◽  
Kunkun Cui ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Solid Solution ◽  
High Temperature ◽  
Bending Strength ◽  
Second Phase ◽  
Strengthening Effect ◽  
Dispersion Strengthening ◽  
The Matrix ◽  
Ultra High Temperature

TiC ceramics have become one of the most potential ultra-high temperature structural materials, because of its high melting point, low density, and low price. However, the poor mechanical properties seriously limit its development and application. In this work, this review follows PRISMA standards, the mechanism of the second phase (particles, whiskers, and carbon nanotubes) reinforced TiC ceramics was reviewed. In addition, the effects of the second phase on the microstructure, phase composition and mechanical properties of TiC ceramics were systematically studied. The addition of carbon black effectively eliminates the residual TiO2 in the matrix, and the bending strength of the matrix is effectively improved by the strengthening bond formed between TiC; SiC particles effectively inhibit the grain growth through pinning, the obvious crack deflection phenomenon is found in the micrograph; The smaller grain size of WC plays a dispersion strengthening role in the matrix and makes the matrix uniformly refined, and the addition of WC forms (Ti, W) C solid solution, WC has a solid solution strengthening effect on the matrix; SiC whiskers effectively improve the fracture toughness of the matrix through bridging and pulling out, the microscopic diagram and mechanism diagram of SiC whisker action process are shown in this paper. The effect of new material carbon nanotubes on the matrix is also discussed; the bridging effect of CNTs can effectively improve the strength of the matrix, during sintering, some CNTs were partially expanded into GNR, in the process of crack bridging and propagation, more fracture energy is consumed by flake GNR. Finally, the existing problems of TiC-based composites are pointed out, and the future development direction is prospected.

Mechanical Properties of Ga1–xInxAs

1985 ◽  
Vol 53 ◽  
Author(s):  
S. Guruswamy ◽  
J.P. Hirth ◽  
K.T. Faber
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
High Temperature ◽  
Strengthening Effect ◽  
Plateau Stress ◽  
Solid Solution Strengthening ◽  
Stress Region ◽  
Solution Strengthening ◽  
Concentration Levels ◽  
Undoped Gaas

ABSTRACTSubstantial solid solution strengthening of GaAs by In acting as InAs4 units has recently been predicted. This strengthening could account for the reduction of dislocation density in GaAs single crystals grown from the melt. High temperature hardness measurements up to 700ºC have been carried out on (100) GaAs and Ga0.9975 In0.0025 As wafers. Results show a significant strengthening effect in In—doped GaAs even at concentration levels of about 0.2 wt%. A temperature independent flow stress region is observed for both these alloys. The In—doped GaAs shows ahigher plateau stress level compared to the undoped GaAs. The results are consistent with the solid solution strengthening model.

Influence of Extrusion Temperature on Property of Graphene Oxide-carbon Fiber Hybrid Reinforced Resin Matrix Composites

2021 ◽  
Author(s):  
Yuqin Ma ◽  
Fei Li ◽  
Wei Xu ◽  
Long Yan ◽  
Haiyin Guo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
Carbon Fiber ◽  
Performance Test ◽  
Bending Strength ◽  
Extrusion Temperature ◽  
Resin Matrix ◽  
Strengthening Effect ◽  
Molding Process ◽  
The Matrix

Abstract The graphene oxide-carbon fiber hybrid reinforced resin matrix (GO-CF/EP) composites were prepared by vacuum infiltration hot-pressing molding process. The effects of extrusion temperature on the microstructure, fracture mechanism and mechanical properties of GO-CF/EP composites were investigated by setting different extrusion temperatures. In the experiments, the extrusion temperature was controlled as 30℃, 40℃, 50℃, 60℃ and 70℃ respectively. It was found that the best mechanical property of composites and infiltration effect of matrix in the fiber gap were obtained at the temperature of 50℃. The bending strength of the material reached 977 MPa through the performance test. The results showed the matrix viscosity was high and the fluidity was poor when the extrusion temperature was low. Poor penetration of the matrix resulted in a large number of fibers failing to bond together. The stress was difficult to transfer to other fibers through the matrix and the strengthening effect of graphene oxide (GO) was weak when the composite was subjected to external force. This phenomenon led to poor mechanical properties of composites. Under the condition of higher temperature, the flow speed of the matrix and the curing speed of composites could be improved. As a result, some of the matrix was solidified in advance while being pressed out, which led to cracks and other defects in the process of loading and affects the mechanical properties of the composites. However, the mechanical properties of the composites with higher extrusion temperature were better than those with lower extrusion temperature due to the existence of graphene oxide in the fiber gap.

scholarly journals Hybrid Effect of PVA Fibre and Carbon Nanotube on the Mechanical Properties and Microstructure of Geopolymers

2021 ◽  
Vol 8 ◽  
Author(s):  
Tao Meng ◽  
Xiufen Yang ◽  
Yue Yu ◽  
Hongming Yu ◽  
Miaozhou Huang
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Bending Strength ◽  
Group Analysis ◽  
Strengthening Mechanism ◽  
Magic Angle Spinning ◽  
Nuclear Magnetic Resonance Analysis ◽  
Magic Angle ◽  
Strengthening Effect ◽  
Wide Range

The concept of geopolymers has been widely studied since it was proposed. However, the wide range of applications of geopolymers is affected by brittleness and poor crack resistance. In this study, the mechanical properties of geopolymers with single-doped PVA fibres, single-doped carbon nanotubes, and mixed PVA fibers and carbon nanotubes were studied respectively first. It was found that PVA fibres and carbon nanotubes had a positive effect on improving the mechanical properties of geopolymers, especially bending strength and flexural strength. Moreover, the incorporation of PVA fibre could improve the damage morphology of geopolymers. Additionally, the phase analysis, structural group analysis, and strengthening mechanism were studied via scanning electron microscopy, mercury intrusion porosimetry analysis, X-ray diffraction pattern characterisation, Fourier transform infrared spectroscopy analysis, and magic angle spinning nuclear magnetic resonance analysis. It was found that the strengthening effect of PVA fiber to the geopolymer was primarily a physical strengthening effect, whereas the strengthening effect of carbon nanotubes to the geopolymers was both chemical and physical. Finally, based on the previous study, a multi-scale dual-fibre strengthening mechanism was proposed. Micro-nano fibre composites were used to improve microstructure via physical and chemical effects. This is helpful to improve the performance and application of geopolymers. Furthermore, it lays a preliminary theoretical foundation for engineering applications and technical improvement of geopolymers in the future.

Effects of Er on Microstructure and Mechanical Properties of Mg-Zn-Er-Zr Magnesium Alloys

2007 ◽  
Vol 546-549 ◽  
pp. 105-108 ◽  
Author(s):  
Qu Dong Wang ◽  
Da Quan Li ◽  
Qiang Li ◽  
Wen Jiang Ding
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Temperature ◽  
Solution Treatment ◽  
Precipitation Process ◽  
Strengthening Effect ◽  
Microstructure And Mechanical Properties ◽  
The Matrix ◽  
Zr Alloy ◽  
Zr Alloys

Microstructure and mechanical properties of Mg-Zn-Er-Zr alloys were characterized in detail. The grain size of as-cast Mg-Zn-Er-Zr alloy was greatly decreased by the Mg-Zn-Er phases formed at grain boundaries. The addition of Er can increase the yield strength (YS) but decrease the ultimate tensile strength (UTS) and elongation of as-cast Mg-Zn-Zr alloy. The thermally stable Mg-Zn-Er phases were just partially dissolved into the matrix during solution treatment. And the addition of Er can prolong the precipitation process of Mg-Zn-Zr alloy. Solution-plus-ageing treatment can increase the strength of both the Mg-Zn-Zr and Mg-Zn-Er-Zr alloys, but the strengthening effect of Mg-Zn-Er-Zr alloy was greatly weakened, for the incompletely solution of Mg-Zn-Er phases. Er can greatly enhance the high temperature elongation of Mg-Zn-Zr alloy, but the increase of high temperature tensile strength was just a little.

The Effect of Refractory Elements on Microstructure and Mechanical Properties of Ni3(Si,Ti) Intermetallic Alloys

2010 ◽  
Vol 654-656 ◽  
pp. 472-475 ◽  
Author(s):  
Akiko Kai ◽  
Daiki Imajo ◽  
Yasuyuki Kaneno ◽  
Takayuki Takasugi
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
High Temperature ◽  
Thin Sheet ◽  
Alloy Sheet ◽  
Solid Solution Phase ◽  
Refractory Element ◽  
Second Phase ◽  
Intermetallic Alloys ◽  
High Temperature Tensile

Microstructure, mechanical properties and cold workability of quaternary Ni3(Si,Ti) intermetallic alloys with L12 structure, which were alloyed with two atomic percent of a refractory element X (X: Hf, Ta and W), were investigated. The Ta-added Ni3(Si,Ti) alloy showed an L12 single phase microstructure, while the microstructure of the Hf-added alloy was comprised of Ni5Hf and/or Ni3Hf intermetallic dispersions in the L12 matrix, and that of the W-added alloy consisted of fcc Ni solid solution phase within the L12 grain. In the homogenized condition, hardness increased in the order of the Hf-added, the Ta-added and the W-added alloys. The hardenings of the Hf-added and the Ta-added alloys were attributed to second-phase dispersion hardening and distinctive solid solution hardening, respectively. Among these alloys, only the W-added alloy was successfully cold-rolled to thin sheet with a thickness of 200 m. It was found that both room-temperature and high-temperature tensile strength of the W-added alloy sheet was enhanced compared with that of the unalloyed Ni3(Si,Ti) sheet. Also, high-temperature tensile ductility was significantly improved in the W-added alloy sheet, by suppressing the propensity of brittle intergranular fracture.

TEM Studies of Grain Boundary Films in Si3N4 Ceramics

1991 ◽  
Vol 49 ◽  
pp. 930-931
Author(s):  
H.-J. Kleebe ◽  
J.S. Vetrano ◽  
J. Bruley ◽  
M. Rühle
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Silicon Nitride ◽  
Hot Isostatic Pressing ◽  
Amorphous Film ◽  
Liquid Phase Sintering ◽  
Second Phase ◽  
High Temperature Mechanical Properties ◽  
Triple Points ◽  
Boundary Films

It is expected that silicon nitride based ceramics will be used as high-temperature structural components. Though much progress has been made in both processing techniques and microstructural control, the mechanical properties required have not yet been achieved. It is thought that the high-temperature mechanical properties of Si3N4 are limited largely by the secondary glassy phases present at triple points. These are due to various oxide additives used to promote liquid-phase sintering. Therefore, many attempts have been performed to crystallize these second phase glassy pockets in order to improve high temperature properties. In addition to the glassy or crystallized second phases at triple points a thin amorphous film exists at two-grain junctions. This thin film is found even in silicon nitride formed by hot isostatic pressing (HIPing) without additives. It has been proposed by Clarke that an amorphous film can exist at two-grain junctions with an equilibrium thickness.

scholarly journals A Study on the Damping Capacities of Mg–Zn–Y-Based Alloys with Lamellar Long Period Stacking Ordered Phases by Preparation Process

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 79
Author(s):  
Ruopeng Lu ◽  
Kai Jiao ◽  
Yuhong Zhao ◽  
Kun Li ◽  
Keyu Yao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Damping Capacity ◽  
Second Phase ◽  
Preparation Process ◽  
Obvious Effect ◽  
Lpso Phase ◽  
Long Period ◽  
Lamellar Phases ◽  
Ordered Phases

Mg alloys with fine mechanical properties and high damping capacities are essential in engineering applications. In this work, Mg–Zn–Y based alloys with lamellar long period stacking ordered (LPSO) phases were obtained by different processes. The results show that a more lamellar second phase can be obtained in the samples with more solid solution atoms. The density of the lamellar LPSO phase has an obvious effect on the damping of the magnesium alloy. The compact LPSO phase is not conducive to dislocation damping, but sparse lamellar phases can improve the damping capacity without significantly reducing the mechanical properties. The Mg95.3Zn2Y2.7 alloy with lamellar LPSO phases and ~100 μm grain size exhibited a fine damping property of 0.110 at ε = 10–3.

scholarly journals Effect of Rare Earth Ce on Deep Stamping Properties of High-Strength Interstitial-Free Steel Containing Phosphorus

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1473
Author(s):  
Hao Wang ◽  
Yanping Bao ◽  
Chengyi Duan ◽  
Lu Lu ◽  
Yan Liu ◽  
...  
Keyword(s):  
Solid Solution ◽  
Grain Size ◽  
Rare Earth ◽  
High Strength ◽  
Rolling Process ◽  
P Element ◽  
Second Phase ◽  
Strengthening Effect ◽  
Interstitial Free ◽  
If Steel

The influence of rare earth Ce on the deep stamping property of high-strength interstitial-free (IF) steel containing phosphorus was analyzed. After adding 120 kg ferrocerium alloy (Ce content is 10%) in the steel, the inclusion statistics and the two-dimensional morphology of the samples in the direction of 1/4 thickness of slab and each rolling process were observed and compared by scanning electron microscope (SEM). After the samples in each rolling process were treated by acid leaching, the three-dimensional morphology and components of the second phase precipitates were observed by SEM and energy dispersive spectrometer (EDS). The microstructure of the sample was observed by optical microscope, and the grain size was compared. Meanwhile, the content and strength of the favorable texture were analyzed by X-ray diffraction (XRD). Finally, the mechanical properties of the product were analyzed. The results showed that: (1) The combination of rare earth Ce with activity O and S in steel had lower Gibbs free energy, and it was easy to generate CeAlO3, Ce2O2S, and Ce2O3. The inclusions size was obviously reduced, but the number of inclusions was increased after adding rare earth. The morphology of inclusions changed from chain and strip to spherical. The size of rare earth inclusions was mostly about 2–5 μm, distributed and dispersed, and their elastic modulus was close to that of steel matrix, which was conducive to improving the structure continuity of steel. (2) The rare earth compound had a high melting point. As a heterogeneous nucleation point, the nucleation rate was increased and the solidification structure was refined. The grade of grain size of products was increased by 1.5 grades, which is helpful to improve the strength and plasticity of metal. (3) Rare earth Ce can inhibit the segregation of P element at the grain boundary and the precipitation of Fe(Nb+Ti)P phase. It can effectively increase the solid solution amount of P element in steel, improve the solid solution strengthening effect of P element in high-strength IF steel, and obtain a large proportion of {111} favorable texture, which is conducive to improving the stamping formability index r90 value.

Sign in / Sign up

Export Citation Format

Share Document