scholarly journals Experimental Investigation on Transient Pressure Characteristics in a Helico-Axial Multiphase Pump

Energies ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 461 ◽  
Author(s):  
Yun Xu ◽  
Shuliang Cao ◽  
Takeshi Sano ◽  
Tokiya Wakai ◽  
Martino Reclari
Keyword(s):  
Pressure Fluctuation ◽  
High Speed ◽  
Oil And Gas ◽  
High Efficiency ◽  
Phase Distribution ◽  
Pressure Rise ◽  
Stable Operation ◽  
Transient Pressure ◽  
Multiphase Pump ◽  
Pressure Characteristics

In oil and gas exploitation, the multiphase pump is a vital piece of equipment to guarantee production with high efficiency and stable operation. The complicated pattern of multiphase flow in the multiphase pump affects the pump performance; for this reason, the multiphase performance and the inner flow should be sufficiently investigated. In the present work, a liquid-gas multiphase pump is designed and manufactured, and then tested in a specialized test rig to reveal the transient pressure characteristics of the multiphase pump. Results show that the dominant frequency under water and water-air conditions is the blade passing frequency, which is induced by the rotor stator interaction. In the downstream of the impeller, the pressure fluctuation is obviously weakened, because the splitter-blade design could improve the control ability of flow pattern in the downstream region. In comparison with water condition, the pressure fluctuation of water-air condition greatly increases, and the multiples of impeller rotating frequency are stimulated due to the movement and merging of air bubbles. Finally, the correlation of transient pressure and phase distribution in impeller is revealed by using a high-speed camera. With the gradual pressure rise from impeller inlet to outlet, the relative movement and separation of two phases induce violent pressure fluctuations.

scholarly journals Phase Distribution in the Tip Clearance of a Multiphase Pump at Multiple Operating Points and Its Effect on the Pressure Fluctuation Intensity

Processes ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 556
Author(s):  
Guangtai Shi ◽  
Zongku Liu ◽  
Xiaobing Liu ◽  
Yexiang Xiao ◽  
Xuelin Tang
Keyword(s):  
Phase Velocity ◽  
Pressure Fluctuation ◽  
Phase Distribution ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Two Phase ◽  
Multiphase Pump ◽  
Fluctuation Intensity ◽  
Operating Points ◽  
Multiple Operating Points

Tip clearance has a great effect on the flow and pressure fluctuation characteristics in a multiphase pump, especially at multiple operating points. The phase distribution and pressure fluctuation in tip clearance in a multiphase pump are revealed using the CFD (computational fluid dynamics) technology and high-speed photography methods. In this paper, the phase distribution, the gas-liquid two-phase velocity slip, and the pressure fluctuation intensity are comprehensively analyzed. Results show with the increase of the tip clearance, the multiphase pump pressurization performance is obviously deteriorated. In the meantime, the gas accumulation mainly occurs at the hub, the blade suction side (SS), and the tip clearance, and the maximum gas-liquid two-phase velocity difference is near the impeller streamwise of 0.4. In addition, the tip clearance improves the gas-liquid two-phase distribution in the pump, that is, the larger the tip clearance is, the more uniform the gas-liquid distribution becomes. Furthermore, the gas leads to the maximum pressure fluctuation intensity in the tip clearance which is closer to the tip leakage flow (TLF) outlet, and has a greater effect on the degree of flow separation in the tip clearance.

Experimental and Numerical Investigation on Pressure Fluctuation of the Impeller in an Axial Flow Pump

2019 ◽  
Author(s):  
Xi Shen ◽  
Desheng Zhang ◽  
Bin Xu ◽  
Yongxin Jin ◽  
Xiongfa Gao
Keyword(s):  
Pressure Fluctuation ◽  
High Speed ◽  
Axial Flow ◽  
Suction Side ◽  
High Speed Photography ◽  
Detached Eddy Simulation ◽  
Transient Pressure ◽  
Unstable Flow ◽  
Axial Flow Pump ◽  
Flow Pump

Abstract The Detached Eddy Simulation (DES) has been used to simulate the pressure fluctuation of the impeller in an axial flow pump. The results were combined with experiments including high-speed photography and transient pressure measurements to investigate the unstable flow induced by tip leakage vortex (TLV). Numerical results show that maximum predictive error values of head is 2.9%, compared with experimental results. The pressure fluctuation at different monitoring points present a certain regularity, with 3 peaks and 3 troughs in a period, corresponding to the number of blades. The amplitude of pressure fluctuation at P1 (impeller inlet) is the highest among those monitoring points, where the amplitude decreases with the flow rates. The dominant frequency of pressure fluctuation at impeller under cavitation condition is the blade passing frequency (BPF). Besides, there are also N* = 6, 9, 12 and other more harmonic frequencies. The cavitation flow was analyzed with the pressure fluctuation of the blade tip. For the existence of the pressure difference between pressure side and suction side, the pressure at monitoring points change alternately. The amplitude of the fluctuation near tip is affected seriously by the cavitation bubbles, as the cavitation could is a low pressure region with unstable fluctuation.

scholarly journals High-efficiency casing perforation oil and gas wells

2021 ◽  
pp. 112-120
Author(s):  
V. G. Pogrebnyak ◽  
◽  
I. I. Chudyk ◽  
A. V. Pogrebnyak ◽  
I. V. Perkun ◽  
...  
Keyword(s):  
High Speed ◽  
Oil And Gas ◽  
High Efficiency ◽  
Dynamic Pressure ◽  
Metal Plate ◽  
Water Jet ◽  
Molecular Weights ◽  
Destructive Action ◽  
Cement Sheath ◽  
Well Cement

The energetic capabilities of a high-speed jet of an aqueous solution of polyethylene oxide (PEO) with varying concentration and different outflow pressures from a jetforming nozzle were investigated using the length of the forming channel in the model of the casing of an oil and gas well, cement sheath and rock layer, as well as impact of the jet force on a metal plate fixed on a physical pendulum. The experimental data made it possible to obtain a calculated dependence in a dimensionless form to determine the quality (initial sections) of jets of aqueous solutions with different concentrations and molecular weights of PEO, considering the real parameters of the jet-forming nozzles of the hydroperforator. A comprehensive study of the perforation process made it possible to substantiate the mechanism of the high destructive capacity of a high-speed jet of polymer solution. It has been established that the mechanism of the high destructive capacity of the polymer water jet is not due to the Toms effect, but caused by the destructive action of the dynamic pressure of the polymer water jet «reinforced» by strongly unfolded macromolecular chains under the action of a tensile flow in the inlet area of the jet forming nozzle of the hydroperforator. Keywords: perforator; jet nozzle; jet quality; casing; cement sheath; rock; Toms effect.

scholarly journals Method of effective circulation control of high speed fans impellors

2021 ◽  
pp. 92-100
Author(s):  
Vladimir Makarov ◽  
Keyword(s):  
Critical Points ◽  
Air Conditioning ◽  
High Speed ◽  
Oil And Gas ◽  
High Efficiency ◽  
Control Flow ◽  
Air Cooling ◽  
Circulation Control ◽  
Gas Cooling ◽  
The Cost

Research relevance. The high-level competitiveness of Russian oil and gas sector enterprises in the global economic space is impossible to reach without accelerating the restructuring of existing air-cooling apparatuses and developing new ones. It should be carried out with regard to modern technology introduction and advanced achievements in mining. The cost of gas cooling during its transportation via main gas pipelines in the cost structure reaches 22%. Besides, annual energy wastage on compressed gas cooling by fan installations is commensurate with the cost of the air cooling devices. It is essential to develop active means of air conditioning units control in order to improve their efficiency and aerodynamic adaptability that affect the competitiveness of oil and gas enterprises. ISSN 0536-1028 «Известия вузов. Горный журнал», № 4, 2021 99 Research aim is to develop a mathematical model for fan unit parameters active control. Research methods are based on the experimentally proven hypothesis about the dependence between the control flow rate on the impeller blades and the position of the rear critical points of the blades. Research results. A method was developed based on conformal transformations, the theory of residues, singular equations, and hydrodynamic analogy. The dependence between the position of the profiles critical points and flow circulation was obtained. The dependence of the aerodynamic adaptability of the fan units in air conditioning devices on effective critical point position and the energy characteristics of the impeller blades flow controlling source has been established. A patent was obtained for the fan unit impeller with active circulation control from air flow sources from the fan casing. High efficiency of the developed circulation control method for increasing the operational efficiency and aerodynamic adaptability of air-cooled fan units has been proved. An aerodynamic scheme of ОV 121TN was developed. A fan unit OGM VU2.7-1.8K4 with aerodynamic adaptability increased by 34% was created.

Qualification of a New Multiphase Pump. the Setting of a New Standard

2021 ◽  
Author(s):  
Åge Hofstad ◽  
Tarje Olderheim ◽  
Magnus Almgren ◽  
Marianna Rondon ◽  
Edouard Thibaut ◽  
...  
Keyword(s):  
High Speed ◽  
Oil And Gas ◽  
Volume Fraction ◽  
Two Phase ◽  
Specific Product ◽  
Multiphase Pump ◽  
Gas Volume Fraction ◽  
Gas Market ◽  
Gas Volume ◽  
Winding Insulation

Abstract The recent trend in the oil industry is to save CAPEX and exploit every offshore field to increase production and maximize reserves. Also, deeper water and longer step-out is a challenge for new fields. The most adapted technology to unlock these reserves is the use of subsea boosting like a multiphase pump on the seafloor. Subsea boosting has been used for decades with well proven results, but up to now, some limitations in power and lift pressure exist. This new multiphase pump development has increased the potential pressure generation manyfold from the typical ΔP of 50 bar (725 psi) at the beginning of the project. Developing such a powerful two-phase pump driven by a liquid-filled motor requires a unique combination of expertise in machinery engineering, electrical engineering, fluid mechanics and rotor dynamics. The objective of the co-authors is to share this experience by bringing some insights on what it takes to develop, test, and qualify such specific product. Outlines of the methodology will be described, key results will be detailed, and lessons learnt will be presented. The new design was fully tested first component-wise and then for a full-size prototype. A wide process envelope was mapped during the final qualification program with 3,000 points tested in the range 2,000-6,000 RPM and 0 - 100% GVF (Gas Volume Fraction). Qualification tests concluded with more than 2,000 cumulative hours. The main challenges in this program were the development of an innovative multiphase impeller and the qualification of the first MPP (MultiPhase Pump) with a back-to-back configuration. Concerning the motor, the development includes a high speed 6,000 RPM, 6 MW liquid-filled induction motor and a new stator winding insulation cable. With this new product, the pump market is ready to overcome challenges to produce deeper and further reservoirs in a constant evolutive oil and gas market.

Predictive Failure Analysis of Solder Joints with Simultaneous High Speed EBSD and EDS

2018 ◽  
Author(s):  
J. Lindsay ◽  
P. Trimby ◽  
J. Goulden ◽  
S. McCracken ◽  
R. Andrews
Keyword(s):  
High Speed ◽  
Solder Joints ◽  
Phase Distribution ◽  
Bond Failure ◽  
Microstructural Parameters ◽  
Snpb Solder ◽  
Grain Orientations ◽  
Accelerated Thermal Cycling ◽  
The Relationship ◽  
Opening Up

Abstract The results presented here show how high-speed simultaneous EBSD and EDS can be used to characterize the essential microstructural parameters in SnPb solder joints with high resolution and precision. Analyses of both intact and failed solder joints have been carried out. Regions of strain localization that are not apparent from the Sn and Pb phase distribution are identified in the intact bond, providing key insights into the mechanism of potential bond failure. In addition, EBSD provides a wealth of quantitative detail such as the relationship between parent Sn grain orientations and Pb coarsening, the morphology and distribution of IMCs on a sub-micron scale and accurate grain size information for all phases within the joint. Such analyses enable a better understanding of the microstructural developments leading up to failure, opening up the possibility of improved accelerated thermal cycling (ATC) testing and better quality control.

One-step Separation and Purification of Four Phenolic Acids from Stenoloma chusanum (L.) Ching by Medium-pressure Liquid Chromatography and High-speed Counter-current Chromatography

2019 ◽  
Vol 9 (2) ◽  
pp. 138-143
Author(s):  
Tianyun Li ◽  
Xiling Dai ◽  
Yichen Li ◽  
Guozheng Huang ◽  
Jianguo Cao
Keyword(s):  
Natural Products ◽  
Liquid Chromatography ◽  
Phenolic Acids ◽  
High Speed ◽  
High Efficiency ◽  
Total Phenolic ◽  
Medium Pressure ◽  
Medium Pressure Liquid Chromatography ◽  
One Step ◽  
Counter Current

Background:Stenoloma chusanum (L.) Ching is a Chinese traditional medicinal fern with high total flavonoid and total phenolic content. Traditionally, phenolic compounds were separated by using column chromatography, which is relatively inefficient. </P><P> Objective: This study aims to use an efficient method to separate natural products from S. chusanum by Medium-Pressure Liquid Chromatography (MPLC) and High-Speed Counter-Current Chromatography (HSCCC).Methods:In the present research, firstly, a sample (2.5 g) from the dichloromethane extract of S. chusanum was separated by MPLC. Next, fraction P5 was purified by HSCCC with a two-phase solvent system composed of hexane-ethyl acetate-methanol-water (HEMWat) at a volume ratio of 2:4:1:4 (v/v/v/v). </P><P> Result: Four phenolic acids were obtained and their structures were identified by means of NMR and ESI-mass analysis. They were identified as: 1) protocatechuic acid (34 mg, purity 90.1%), 2) syringic acid (66 mg, purity 99.0%), 3) p-hydroxybenzoic acid (5 mg, purity 91.2%) and 4) vanillic acid (6 mg, purity 99.3%).Conclusion:The combination of MPLC and HSCCC is a high-efficiency separation method for natural products. This is the first report with regard to the separation of four phenolic acids in one step by MPLC and HSCCC from S. chusanum (L.) Ching.

Stable operation of multiple-lateral-mode ridge-waveguide lasers for high-speed printing

1997 ◽  
Vol 33 (3) ◽  
pp. 214
Author(s):  
R. LaComb ◽  
D.K. Wagner ◽  
L. DiMarco ◽  
J. Connolly
Keyword(s):  
High Speed ◽  
Ridge Waveguide ◽  
Stable Operation ◽  
Waveguide Lasers ◽  
Lateral Mode ◽  
Ridge Waveguide Lasers

scholarly journals On-chip trans-dimensional plasmonic router

Nanophotonics ◽  
2020 ◽  
Vol 9 (10) ◽  
pp. 3357-3365 ◽  
Author(s):  
Shaohua Dong ◽  
Qing Zhang ◽  
Guangtao Cao ◽  
Jincheng Ni ◽  
Ting Shi ◽  
...  
Keyword(s):  
High Speed ◽  
High Efficiency ◽  
Incident Angle ◽  
Reciprocal Lattice ◽  
Plasmonic Waveguide ◽  
Optical Diffraction ◽  
Local Dynamic ◽  
Phase Gradient ◽  
On Chip ◽  
Plasmon Polaritons

AbstractPlasmons, as emerging optical diffraction-unlimited information carriers, promise the high-capacity, high-speed, and integrated photonic chips. The on-chip precise manipulations of plasmon in an arbitrary platform, whether two-dimensional (2D) or one-dimensional (1D), appears demanding but non-trivial. Here, we proposed a meta-wall, consisting of specifically designed meta-atoms, that allows the high-efficiency transformation of propagating plasmon polaritons from 2D platforms to 1D plasmonic waveguides, forming the trans-dimensional plasmonic routers. The mechanism to compensate the momentum transformation in the router can be traced via a local dynamic phase gradient of the meta-atom and reciprocal lattice vector. To demonstrate such a scheme, a directional router based on phase-gradient meta-wall is designed to couple 2D SPP to a 1D plasmonic waveguide, while a unidirectional router based on grating metawall is designed to route 2D SPP to the arbitrarily desired direction along the 1D plasmonic waveguide by changing the incident angle of 2D SPP. The on-chip routers of trans-dimensional SPP demonstrated here provide a flexible tool to manipulate propagation of surface plasmon polaritons (SPPs) and may pave the way for designing integrated plasmonic network and devices.

scholarly journals Development of Real-Time Time Gated Digital (TGD) OFDR Method and Its Performance Verification

Sensors ◽  
2021 ◽  
Vol 21 (14) ◽  
pp. 4865
Author(s):  
Kinzo Kishida ◽  
Artur Guzik ◽  
Ken’ichi Nishiguchi ◽  
Che-Hsien Li ◽  
Daiji Azuma ◽  
...  
Keyword(s):  
Real Time ◽  
Optical Fibers ◽  
High Speed ◽  
Oil And Gas ◽  
Scattered Light ◽  
Oil And Gas Industry ◽  
High Signal ◽  
Chirp Pulse ◽  
Sound Waves ◽  
Industry Applications

Distributed acoustic sensing (DAS) in optical fibers detect dynamic strains or sound waves by measuring the phase or amplitude changes of the scattered light. This contrasts with other distributed (and more conventional) methods, such as distributed temperature (DTS) or strain (DSS), which measure quasi-static physical quantities, such as intensity spectrum of the scattered light. DAS is attracting considerable attention as it complements the conventional distributed measurements. To implement DAS in commercial applications, it is necessary to ensure a sufficiently high signal-noise ratio (SNR) for scattered light detection, suppress its deterioration along the sensing fiber, achieve lower noise floor for weak signals and, moreover, perform high-speed processing within milliseconds (or sometimes even less). In this paper, we present a new, real-time DAS, realized by using the time gated digital-optical frequency domain reflectometry (TGD-OFDR) method, in which the chirp pulse is divided into overlapping bands and assembled after digital decoding. The developed prototype NBX-S4000 generates a chirp signal with a pulse duration of 2 μs and uses a frequency sweep of 100 MHz at a repeating frequency of up to 5 kHz. It allows one to detect sound waves at an 80 km fiber distance range with spatial resolution better than a theoretically calculated value of 2.8 m in real time. The developed prototype was tested in the field in various applications, from earthquake detection and submarine cable sensing to oil and gas industry applications. All obtained results confirmed effectiveness of the method and performance, surpassing, in conventional SM fiber, other commercially available interrogators.

Sign in / Sign up

Export Citation Format

Share Document