scholarly journals Temporal Evolution of Split-Injected Fuel Spray at Elevated Chamber Pressures

Energies ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 4284 ◽  
Author(s):  
Gang Wu ◽  
Xinyi Zhou ◽  
Tie Li
Keyword(s):  
High Speed ◽  
Fuel Injection ◽  
Penetration Rate ◽  
Injection Pressure ◽  
Test System ◽  
Injection Rate ◽  
Spray Angle ◽  
Split Injection ◽  
Injection Strategy ◽  
Injection Strategies

For reducing soot and NOx emissions, an effective method is to apply split injection strategies. In this research, characteristics of split injection were investigated by applying the pilot-main injection strategy and main-post injection strategy. The injection mass of fuel with the two strategies was measured by an in-house fuel injection rate test system based on the Bosch method. The development of spray tip and tail penetrations, as well as the evolvement of the spray angle when applying these two injection strategies, were explored by employing the high speed shadowgraphy at various injection pressures and surrounding gas densities. The results indicate the tail penetration rate of spray has no relation to the fuel injection pressure. However, the increased injection pressure causes a faster penetration development in the spray tip position. It was also found that the spray tip penetration rate of the second spray is slightly slower than that of the first spray at the beginning stage of injection, but it was significantly larger than the first one at the later stage.

Effects of split and single injection strategies on particle number emission and combustion of a GDI engine

2018 ◽  
Vol 233 (5) ◽  
pp. 1100-1114 ◽  
Author(s):  
Fangxi Xie ◽  
Wenliang Zheng ◽  
Hong Chen ◽  
Yu Liu ◽  
Yan Su ◽  
...  
Keyword(s):  
Fuel Consumption ◽  
Particle Number ◽  
Fuel Injection ◽  
Single Injection ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Brake Specific Fuel Consumption ◽  
Split Injection ◽  
Injection Strategy ◽  
Injection Strategies

Influence of fuel injection parameters of the single and split injection strategies on combustion, performance and particle number emission had been investigated on a gasoline direct injection engine with stoichiometric mixture combustion under medium and low engine operating conditions. The test results showed that the optimal injection timing for single injection strategy was about 290–280 °CA BTDC, and an earlier or a later injection timing could lead to a deterioration of particle number emission. For split injection strategy, the injected parameters also needed to be optimized subtly in order to improve particle number emission. When the inappropriate injected parameters were adopted, particle number emission increased rather than decrease when compared with single injection strategy. Similar to single injection strategy, when the second injection timing of split injection strategy further retarded from 280 °CA BTDC, the particle number emission and brake-specific fuel consumption also started to deteriorate, and the in-cylinder combustion process was delayed and slowed. The optimal first injection timing was about 300 °CA BTDC. When the first injection timing was delayed to 280 °CA BTDC with the second injection timing being 260 °CA BTDC, the particle number emission increased and the shortened interval time between first and second fuel injection might have had a negative effect. The smaller difference of the fuel quantity between the first and the second injection was not good for the improvement of particle number emission and brake-specific fuel consumption, and the best injection proportion was 2:8. Overall, the engine particle number emission could be decreased to some extent, which could reach about 10–30%, by split injection strategy with optimal control parameters at medium and low engine loads.

scholarly journals Numerical Investigation of an RCCI Engine Fueled with Natural Gas/Dimethyl-Ether in Various Injection Strategies

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1638
Author(s):  
Ayat Gharehghani ◽  
Alireza Kakoee ◽  
Amin Mahmoudzadeh Andwari ◽  
Thanos Megaritis ◽  
Apostolos Pesyridis
Keyword(s):  
Fuel Injection ◽  
Single Injection ◽  
Split Injection ◽  
Lower Efficiency ◽  
Injection Strategy ◽  
Compression Ignition Engines ◽  
Start Of Injection ◽  
Single Strategy ◽  
Direct Fuel Injection ◽  
Injection Strategies

Reactivity control compression ignition engines illustrated suitable abilities in emission reduction beside high thermal efficiency. In this research, nine various direct fuel injection strategies were studied numerically: three cases with single injection strategy and six cases with split injection and different start of injection (SOI). In all simulated cases, equivalence ratio kept constant (i.e., 0.3). Among various strategies, single injection showed higher IMEP as a factor of efficiency with about 5.39 bar that occurred at SOI = 60 before top dead center (bTDC), while lower efficiency was observed for split injection case with 50%-50% injections of fuel in each injection stage. Start of combustion (SOC), burn duration and CA50 as factors for combustion characteristics were affected with SOI changes. In single SOI strategies, more advanced injection caused more advanced SOC where there was about 1.3 CAD advancing from 40 to 80 bTDC injection. Spilt SOI showed more advanced SOC, which, also more advanced, was allocated to 50%-50% split injection strategy. There was also the same trend in CA50 changes during change in SOI. Burn duration variations were insignificant and all of them approximately close to 4.5 CAD. According to the emissions researched in this study (Nitrogen Oxides (NOx), monoxide carbon (CO) and unburned hydro carbons (UHC)), all of these pollutants are below euro six diesel standards. Contours of emissions show that there were appropriate SOI for each case study, which were 45 degree bTDC for single strategy, 48 degree bTDC for 80%-20% mass injection and 70 degree bTDC for 50%-50% cases.

scholarly journals Optimizing split fuel injection strategies to avoid pre-ignition and super-knock in turbocharged engines

2019 ◽  
Vol 22 (1) ◽  
pp. 199-221 ◽  
Author(s):  
Eshan Singh ◽  
Kai Morganti ◽  
Robert Dibble
Keyword(s):  
Fuel Injection ◽  
Combustion Process ◽  
Effective Pressure ◽  
Split Injection ◽  
Injection Strategy ◽  
Gasoline Engines ◽  
Specific Output ◽  
Indicated Mean Effective Pressure ◽  
Cycle Variation ◽  
Injection Strategies

Fuel injection strategies often have a considerable impact on pre-ignition in high specific output gasoline engines. Splitting the injection event into two or more pulses has been widely explored as one means of reducing pre-ignition. As effective as these strategies can be with respect to pre-ignition suppression, they often introduce other compromises into the combustion process, for example, reduced indicated mean effective pressure or greater cycle-to-cycle variation. This study examines a split injection strategy with up to three injection pulses for suppressing pre-ignition, while optimizing the start of injection and duration of injection to minimize the associated compromises on the combustion process. The results demonstrate that splitting the injection event generally lowers the in-cylinder temperature and reduces the fuel mass that reaches the cylinder liner. This leads to a lower probability of creating oil-fuel droplets, which may act as a precursor for pre-ignition. The split injection strategy with a late injection when the piston is close to top dead center is shown to perform even better in terms of pre-ignition suppression, while providing comparable indicated mean effective pressure and cycle-to-cycle variation to the baseline case with a single injection pulse. Finally, the injection pressure is varied to establish an optimal combination of operating parameters for avoiding pre-ignition in high specific output gasoline engines.

Behavior of Unsteady Turbulent Starting Round Jets

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
Neerav Abani ◽  
Jaal B. Ghandhi
Keyword(s):  
High Speed ◽  
Penetration Rate ◽  
Injection Rate ◽  
Injection Velocity ◽  
Time Varying ◽  
Velocity Change ◽  
Rate Of Penetration ◽  
Round Jets ◽  
The Difference ◽  
Sudden Decrease

Turbulent starting jets with time-varying injection velocities were investigated using high-speed schlieren imaging. Two solenoid-controlled injectors fed a common plenum upstream of an orifice; using different upstream pressures and actuation times, injection-rate profiles with a step increase or decrease in injection velocity were tested. The behavior of the jet was found to be different depending on the direction of the injection-velocity change. A step increase in injection velocity resulted in an increased rate of penetration relative to the steady-injection case, and a larger increase in injection velocity resulted in an earlier change in the tip-penetration rate. The step-increase data were found to be collapsed by scaling the time by a convective time scale based on the tip location at the time of the injection-velocity change and the difference in the injection velocities. A sudden decrease in injection velocity to zero was found to cause a deviation from the corresponding steady-pressure case at a time that was independent of the initial jet velocity, i.e., it was independent of the magnitude of the injection-velocity change. Two models for unsteady injection from the literature were tested and some deficiencies in the models were identified.

scholarly journals A Study of Combustion Characteristics of Two Gasoline–Biodiesel Mixtures on RCEM Using Various Fuel Injection Pressures

Energies ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 3265
Author(s):  
Ardhika Setiawan ◽  
Bambang Wahono ◽  
Ocktaeck Lim
Keyword(s):  
Heat Release ◽  
Ignition Delay ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Fuel Mixture ◽  
Injection Rate ◽  
Injection Duration ◽  
Late Start ◽  
Fuel Injection Rate ◽  
Injection Pressures

Experimental research was conducted on a rapid compression and expansion machine (RCEM) that has characteristics similar to a gasoline compression ignition (GCI) engine, using two gasoline–biodiesel (GB) blends—10% and 20% volume—with fuel injection pressures varying from 800 to 1400 bar. Biodiesel content lower than GB10 will result in misfires at fuel injection pressures of 800 bar and 1000 bar due to long ignition delays; this is why GB10 was the lowest biodiesel blend used in this experiment. The engine compression ratio was set at 16, with 1000 µs of injection duration and 12.5 degree before top dead center (BTDC). The results show that the GB20 had a shorter ignition delay than the GB10, and that increasing the injection pressure expedited the autoignition. The rate of heat release for both fuel mixes increased with increasing fuel injection pressure, although there was a degradation of heat release rate for the GB20 at the 1400-bar fuel injection rate due to retarded in-cylinder peak pressure at 0.24 degree BTDC. As the ignition delay decreased, the brake thermal efficiency (BTE) decreased and the fuel consumption increased due to the lack of air–fuel mixture homogeneity caused by the short ignition delay. At the fuel injection rate of 800 bar, the GB10 showed the worst efficiency due to the late start of combustion at 3.5 degree after top dead center (ATDC).

Visualization of diesel spray and combustion from lateral side of two-dimensional piston cavity in rapid compression and expansion machine

2020 ◽  
pp. 146808742096229
Author(s):  
Chengyuan Fan ◽  
Daoyuan Wang ◽  
Keiya Nishida ◽  
Yoichi Ogata
Keyword(s):  
High Speed ◽  
Combustion Process ◽  
Video Camera ◽  
Lateral Side ◽  
Two Dimensional ◽  
Split Injection ◽  
Compression And Expansion ◽  
Color Video ◽  
Wall Interaction ◽  
Injection Strategies

Effect of spray/wall interaction in a rapid compression and expansion machine on mixture formation, ignition location, and soot generation was investigated. A two-dimensional piston cavity designed as the cross section of a reentrant piston was utilized to observe the spray and combustion process from the lateral side. The experiment was conducted at 120 MPa injection pressure under single and split injection strategies with an ambient gas of 15% O2 concentration. A shadow methodology was applied to investigate the interaction between the fuel spray and the piston cavity. Combined with the natural flame luminosity captured by a high-speed color video camera, the behaviors of the impinging spray and the combustion process were studied. The combustion characteristics of the in-cylinder pressure, heat release and combustion phase were recorded and analyzed simultaneously. The results showed that the split injection strategies effectively softened the heat release trace and promoted the onset of the main combustion. The cool-flame phenomenon was captured by using the high-speed color video camera, and the intense ignition was observed when the pilot spray was controlled to impinge on the lower lip of the piston rim. Moreover, results also showed that further extending the mixing process of the pilot spray is inclined to form a homogeneous mixture which was beneficial for the promotion of low-temperature combustion and the reduction of soot generation. This research provides a detailed investigation on the spray and combustion process and it highlights the significant effect of spray/wall interaction on the subsequent combustion process.

Effect of the Fuel Injection Strategy on Diesel Particulate Filter Regeneration in a Single-Cylinder Diesel Engine

2016 ◽  
Vol 138 (10) ◽  
Author(s):  
Sungjun Yoon ◽  
Hongsuk Kim ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Fuel Injection ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Particulate Filter ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Diesel Particulate ◽  
Injection Strategy ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

Stringent emission regulations (e.g., Euro-6) have forced automotive manufacturers to equip a diesel particulate filter (DPF) on diesel cars. Generally, postinjection is used as a method to regenerate the DPF. However, it is known that postinjection deteriorates the specific fuel consumption and causes oil dilution for some operating conditions. Thus, an injection strategy for regeneration is one of the key technologies for diesel powertrains equipped with a DPF. This paper presents correlations between the fuel injection strategy and exhaust gas temperature for DPF regeneration. The experimental apparatus consists of a single-cylinder diesel engine, a DC dynamometer, an emission test bench, and an engine control system. In the present study, the postinjection timing was in the range of 40 deg aTDC to 110 deg aTDC and double postinjection was considered. In addition, the effects of the injection pressure were investigated. The engine load was varied among low load to midload conditions, and the amount of fuel of postinjection was increased up to 10 mg/stk. The oil dilution during the fuel injection and combustion processes was estimated by the diesel loss measured by comparing two global equivalences ratios: one measured from a lambda sensor installed at the exhaust port and one estimated from the intake air mass and injected fuel mass. In the present study, the differences of the global equivalence ratios were mainly caused by the oil dilution during postinjection. The experimental results of the present study suggest optimal engine operating conditions including the fuel injection strategy to obtain an appropriate exhaust gas temperature for DPF regeneration. The experimental results of the exhaust gas temperature distributions for various engine operating conditions are discussed. In addition, it was revealed that the amount of oil dilution was reduced by splitting the postinjection (i.e., double postinjection). The effects of the injection pressure on the exhaust gas temperature were dependent on the combustion phasing and injection strategies.

Evaluation of Diesel Low Temperature Combustion Fuel-Injection Strategies at Different Engine Loads

2010 ◽  
Author(s):  
Usman Asad ◽  
Ming Zheng
Keyword(s):  
Management Strategy ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Combustion Efficiency ◽  
Load Management ◽  
Low Temperature Combustion ◽  
High Hydrocarbon ◽  
Temperature Combustion ◽  
Wall Wetting ◽  
Injection Strategies

High hydrocarbon levels in the exhaust, increased cycle-to-cycle variation and reduced energy-efficiency are typical problems associated with diesel LTC operation. To overcome these challenges, three different fuel injection strategies (late single-injection, early multiple-injections and split-injections) have been investigated on a modified single cylinder common-rail diesel engine. The effects of EGR, boost and injection pressure on the emissions and combustion efficiency have been analyzed. The effect of heavy EGR has been quantified in terms of a trade-off between the combustion phasing and the combustion efficiency. To minimize fuel condensation and wall-wetting with early injections, a criterion for selecting the earliest timing for injection during the compression stroke has also been evaluated. This research is concluded with the formulation of a load management strategy to enable energy-efficient diesel LTC up to 10 bar IMEP.

Direct Water Injection to Improve Diesel Spray Combustion

2003 ◽  
Author(s):  
Koji Takasaki ◽  
Tatsuo Takaishi ◽  
Hiroyuki Ishida ◽  
Keijirou Tayama
Keyword(s):  
Diesel Engines ◽  
High Speed ◽  
Fuel Injection ◽  
Nox Reduction ◽  
Water Injection ◽  
Injection Pressure ◽  
Injection System ◽  
Injection Hole ◽  
Low Speed ◽  
Direct Water Injection

Now, it is essential to apply some measures for NOx reduction to low-speed diesel engines emitting much more NOx than high-speed engines. At the same time PM emission must be reduced especially when bunker fuel or heavy fuel is burned. This paper describes the applications of SFWI (Stratified Fuel Water Injection) system and DWI (Direct Water Injection) system to large sized diesel engines to reduce NOx and PM emission. SFWI system makes it possible to inject water during fuel injection from the same nozzle hole without mixing the liquids. DWI system injects water with high injection pressure from the other injection hole than the fuel injection hole into the combustion chamber directly. For testing both the systems, a 2-stroke-cycle low-speed test engine was used.

Sign in / Sign up

Export Citation Format

Share Document