scholarly journals Analytical and Simulation Fair Comparison of Three Level Si IGBT Based NPC Topologies and Two Level SiC MOSFET Based Topology for High Speed Drives

Energies ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 4571 ◽  
Author(s):  
Jelena Loncarski ◽  
Vito Giuseppe Monopoli ◽  
Riccardo Leuzzi ◽  
Leposava Ristic ◽  
Francesco Cupertino
Keyword(s):  
Output Power ◽  
Heat Sink ◽  
High Speed ◽  
Dynamic Models ◽  
Maximum Output Power ◽  
Life Time ◽  
Experimental Tests ◽  
Oxide Semiconductor ◽  
Maximum Output ◽  
Fair Comparison

Wide bandgap (WBG) power devices such as silicon carbide (SiC) can viably supply high speed electrical drives, due to their capability to increase efficiency and reduce the size of the power converters. On the other hand, high frequency operation of the SiC devices emphasizes the effect of parasitics, which generates reflected wave transient overvoltage on motor terminals, reducing the life time and the reliability of electric drives. In this paper, a SiC metal-oxide-semiconductor field-effect transistor (MOSFET) based two level (2L) inverter is systematically studied and compared to the performance of Si insulated-gate bipolar transistor (IGBT) based three level (3L) neutral point clamped (NPC) inverter topologies, for high speed AC motor loads, in terms of efficiency, overvoltages, heat sink design, and cost. A fair comparison was introduced for the first time, having the same output voltage capabilities, output current total harmonic distortion (THD), and overvoltages for the three systems. The analysis indicated the convenience of using the SiC MOSFET based 2L inverter for lower output power. In the case of the maximum output power, the heat sink volume was found to be 20% higher for the 2L SiC based inverter when compared to 3L NPC topologies. Simulations were carried out by realistic dynamic models of power switch modules obtained from the manufacturer’s experimental tests and verified both in the LTspice and PLECS simulation packages.

scholarly journals Novel Heat-Mitigating Chip-on-Probe for Brain Stimulation Behavior Experiments

Sensors ◽  
2020 ◽  
Vol 20 (24) ◽  
pp. 7334
Author(s):  
Seongwoog Oh ◽  
Jungsuek Oh
Keyword(s):  
Brain Stimulation ◽  
Heat Sink ◽  
Transmission Loss ◽  
Maximum Output Power ◽  
Circuit Board ◽  
Oxide Semiconductor ◽  
Normal Operation ◽  
Cmos Process ◽  
Maximum Output ◽  
The Brain

This paper proposes a novel design for a chip-on-probe with the aim of overcoming the heat dissipation effect during brain stimulations using modulated microwave signals. The temperature of the stimulus chip during normal operation is generally 40 °C–60 °C, which is sufficient to cause unintended temperature effects during stimulation. This effect is particularly fatal in brain stimulation applications that require repeated stimulation. This paper proposes, for the first time, a topology that vertically separates the stimulus chip generating the stimulus signal and the probe delivering the signal into the brain to suppress the heat transfer while simultaneously minimizing the radio frequency (RF) transmission loss. As the proposed chip-on-probe should be attached to the head of a small animal, an auxiliary board with a heat sink was carefully designed considering the weight that does not affect the behavior experiment. When the transition structures are properly designed, a heat sink can be mounted to maximize the cooling effect, reducing the temperature by more than 13 °C in a simulation when the heat generated by the chip is transferred to the brain, while the transition from the chip to the probe experiences a loss of 1.2 dB. Finally, the effectiveness of the proposed design is demonstrated by fabricating a chip with the 0.28 μm silicon-on-insulator (SOI) complementary metal–oxide–semiconductor (CMOS) process and a probe with a RT6010 printed-circuit board (PCB), showing a temperature reduction of 49.8 °C with a maximum output power of 11 dBm. In the proposed chip-on-probe device, the temperature formed in the area in contact with the brain is measured at 31.1 °C.

scholarly journals One-Step Preparation of Biochar Electrodes and Their Applications in Sediment Microbial Electrochemical Systems

Catalysts ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 508
Author(s):  
Kui You ◽  
Zihan Zhou ◽  
Chao Gao ◽  
Qiao Yang
Keyword(s):  
Output Power ◽  
Electrode Materials ◽  
Maximum Output Power ◽  
Composite Cathode ◽  
Maximum Output ◽  
Electrochemical Systems ◽  
Composite Cathodes ◽  
One Step ◽  
Microbial Electrochemical Systems ◽  
Hot Melt

Biochar is a kind of carbon-rich material formed by pyrolysis of biomass at high temperature in the absence or limitation of oxygen. It has abundant pore structure and a large surface area, which could be considered the beneficial characteristics for electrodes of microbial electrochemical systems. In this study, reed was used as the raw material of biochar and six biochar-based electrode materials were obtained by three methods, including one-step biochar cathodes (BC 800 and BC 700), biochar/polyethylene composite cathodes (BP 5:5 and BP 6:4), and biochar/polyaniline/hot-melt adhesive composite cathode (BPP 5:1:4 and BPP 4:1:5). The basic physical properties and electrochemical properties of the self-made biochar electrode materials were characterized. Selected biochar-based electrode materials were used as the cathode of sediment microbial electrochemical reactors. The reactor with pure biochar electrode (BC 800) achieves a maximum output power density of 9.15 ± 0.02 mW/m2, which increases the output power by nearly 80% compared with carbon felt. When using a biochar/polyaniline/hot-melt adhesive (BPP 5:1:4) composite cathode, the output power was increased by 2.33 times. Under the premise of ensuring the molding of the material, the higher the content of biochar, the better the electrochemical performance of the electrodes. The treatment of reed powder before pyrolysis is an important factor for the molding of biochar. The one-step molding biochar cathode had satisfactory performance in sediment microbial electrochemical systems. By exploring the biochar-based electrode, waste biomass could be reused, which is beneficial for the environment.

scholarly journals Study of the Properties of a Hybrid Piezoelectric and Electromagnetic Energy Harvester for a Civil Engineering Low-Frequency Sloshing Environment

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 391
Author(s):  
Nan Wu ◽  
Yuncheng He ◽  
Jiyang Fu ◽  
Peng Liao
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Civil Engineering ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electromagnetic Energy ◽  
Maximum Output ◽  
Piezoelectric Film ◽  
Hybrid Energy ◽  
Level Height

In this paper a novel hybrid piezoelectric and electromagnetic energy harvester for civil engineering low-frequency sloshing environment is reported. The architecture, fabrication and characterization of the harvester are discussed. The hybrid energy harvester is composed of a permanent magnet, copper coil, and PVDF(polyvinylidene difluoride) piezoelectric film, and the upper U-tube device containing a cylindrical fluid barrier is connected to the foundation support plate by a hinge and spring. The two primary means of energy collection were through the vortex street, which alternately impacted the PVDF piezoelectric film through fluid shedding, and the electromotive force (EMF) induced by changes in the magnetic field position in the conducting coil. Experimentally, the maximum output power of the piezoelectric transformer of the hybrid energy harvester was 2.47 μW (circuit load 270 kΩ; liquid level height 80 mm); and the maximum output power of the electromagnetic generator was 2.72 μW (circuit load 470 kΩ; liquid level height 60 mm). The low-frequency sloshing energy collected by this energy harvester can drive microsensors for civil engineering monitoring.

LD-pumped high-power continuous-wave Pr3+:YLF deep red lasers at 718.5 and 720.8 nm

Laser Physics ◽  
2021 ◽  
Vol 32 (2) ◽  
pp. 025801
Author(s):  
Xiangrui Liu ◽  
Zhuang Li ◽  
Chengkun Shi ◽  
Bo Xiao ◽  
Run Fang ◽  
...  
Keyword(s):  
Output Power ◽  
High Power ◽  
Slope Efficiency ◽  
Laser Emission ◽  
Continuous Wave ◽  
Optical Glass ◽  
Maximum Output Power ◽  
Glass Plate ◽  
Maximum Output ◽  
First Time

Abstract We demonstrated 22 W LD-pumped high-power continuous-wave (CW) deep red laser operations at 718.5 and 720.8 nm based on an a-cut Pr3+:YLF crystal. The output power of both polarized directions reached the watt-level without output power saturation. A single wavelength laser operated at 720.8 nm in the π-polarized direction was achieved, with a high output power of 4.5 W and high slope efficiency of approximately 41.5%. To the best of our knowledge, under LD-pumped conditions, the laser output power and slope efficiency are the highest at 721 nm. By using a compact optical glass plate as an intracavity etalon, we suppressed the π-polarized 720.8 nm laser emission. And σ-polarized single-wavelength laser emission at 718.5 nm was achieved, with a maximum output power of 1.45 W and a slope efficiency of approximately 17.8%. This is the first time that we have achieved the σ-polarized laser emission at 718.5 nm generated by Pr3+:YLF lasers.

Design and Analysis of a High Power Density, Low Temperature Waste Heat Recovery System Using an Oil-Free Turboalternator

2010 ◽  
Author(s):  
James F. Walton ◽  
Andrew Hunsberger ◽  
Hooshang Heshmat
Keyword(s):  
Output Power ◽  
Waste Heat ◽  
Maximum Output Power ◽  
Output Power Level ◽  
Working Fluid ◽  
Prototype System ◽  
Low Grade ◽  
Maximum Output ◽  
Test Results ◽  
Study Results

In this paper the authors will present the design and preliminary test results for a distributed electric generating system that uses renewable energy source for economical load-following and peak-shaving capability in an oil-free, high-speed micro-turboalternator system using compliant foil bearings and a permanent magnet alternator. Test results achieved with the prototype system operating to full speed and under power generating mode will be presented. A comparison between predicted and measured electrical output will also be presented up to a power generating level of 25 kWe at approximately 55,000 rpm. The excellent correlation between design and test provides the basis for scale up to larger power levels. Based upon the turboalternator test results a thermodynamic cycle analysis of a system using low grade waste heat water at approximately 100 C will be reviewed. The tradeoff study results for a series of environmentally friendly refrigerant working fluids will also be presented including sensitivity to vaporization and condensing temperatures. Based on the cycle and pinch point analyses predicted maximum output power was determined. Finally a preliminary turbine design for the selected R134a working fluid was completed. The results of this study show that a net output power level of greater than 40 kW is possible for approximately 240 l/m flow of water at 100C is possible.

Modelling of Mechanical Nonlinearity in an Electromagnetic Vibration Energy Harvester Using a Forced Duffing Equation

2012 ◽  
Author(s):  
S. D. Moss ◽  
L. A. Vandewater ◽  
S. C. Galea
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Duffing Oscillator ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Homotopy Analysis ◽  
Wire Coil

This work reports on the modelling and experimental validation of a bi-axial vibration energy harvesting approach that uses a permanent-magnet/ball-bearing arrangement and a wire-coil transducer. The harvester’s behaviour is modelled using a forced Duffing oscillator, and the primary first order steady state resonant solutions are found using the homotopy analysis method (or HAM). Solutions found are shown to compare well with measured bearing displacements and harvested output power, and are used to predict the wideband frequency response of this type of vibration energy harvester. A prototype harvesting arrangement produced a maximum output power of 12.9 mW from a 12 Hz, 500 milli-g (or 4.9 m/s2) rms excitation.

scholarly journals Continuous-Wave and Passively Q-Switched Er:Y2O3 Ceramic Laser at 2.7 μm

2018 ◽  
Vol 2018 ◽  
pp. 1-5 ◽  
Author(s):  
Zhipeng Qin ◽  
Guoqiang Xie ◽  
Jian Zhang ◽  
Jingui Ma ◽  
Peng Yuan ◽  
...  
Keyword(s):  
Output Power ◽  
Continuous Wave ◽  
Maximum Output Power ◽  
Maximum Output ◽  
Average Output ◽  
Semiconductor Saturable Absorber ◽  
Infrared Spectral ◽  
Maximum Average Output Power ◽  
Ceramic Laser ◽  
Stable Passive

We report on a continuous-wave (CW) and passively Q-switched Er:Y2O3 ceramic laser in mid-infrared spectral region. In the CW regime, a maximum output power of 2.07 W is achieved at 2717.3 nm with a slope efficiency of 13.5%. Stable passive Q-switching of the Er:Y2O3 ceramic laser is demonstrated based on semiconductor saturable absorber mirror. Under an absorbed pump power of 12.4 W, a maximum average output power of 223 mW is generated with a pulse energy of 1.7 μJ and a pulse width of 350 ns at 2709.3 nm.

Sign in / Sign up

Export Citation Format

Share Document