scholarly journals Evaluation of Mathematical Model to Characterize the Performance of Conventional and Hybrid PV Array Topologies under Static and Dynamic Shading Patterns

Energies ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 3216 ◽  
Author(s):  
Manoharan Premkumar ◽  
Umashankar Subramaniam ◽  
Thanikanti Sudhakar Babu ◽  
Rajvikram Madurai Elavarasan ◽  
Lucian Mihet-Popa
Keyword(s):  
Mathematical Model ◽  
Performance Analysis ◽  
Fill Factor ◽  
Partial Shading ◽  
Pv Systems ◽  
Pv Array ◽  
Pv Module ◽  
Pv Modules ◽  
Power Maximization ◽  
Global Peak

The analysis and the assessment of interconnected photovoltaic (PV) modules under different shading conditions and various shading patterns are presented in this paper. The partial shading conditions (PSCs) due to the various factors reduce the power output of PV arrays, and its characteristics have multiple peaks due to the mismatching losses between PV panels. The principal objective of this paper is to model, analyze, simulate and evaluate the performance of PV array topologies such as series-parallel (SP), honey-comb (HC), total-cross-tied (TCT), ladder (LD) and bridge-linked (BL) under different shading patterns to produce the maximum power by reducing the mismatching losses (MLs). Along with the conventional PV array topologies, this paper also discusses the hybrid PV array topologies such as bridge-linked honey-comb (BLHC), bridge-linked total-cross-tied (BLTCT) and series-parallel total-cross-tied (SPTCT). The performance analysis of the traditional PV array topologies along with the hybrid topologies is carried out during static and dynamic shading patterns by comparing the various parameters such as the global peak (GP), local peaks (LPs), corresponding voltage and current at GP and LPs, fill factor (FF) and ML. In addition, the voltage and current equations of the HC configuration under two shading conditions are derived, which represents one of the novelties of this paper. The various parameters of the SPR-200-BLK-U PV module are used for PV modeling and simulation in MATLAB/Simulink software. Thus, the obtained results provide useful information to the researchers for healthy operation and power maximization of PV systems.

scholarly journals A Simple Mismatch Mitigating Partial Power Processing Converter for Solar PV Modules

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2308
Author(s):  
Kamran Ali Khan Niazi ◽  
Yongheng Yang ◽  
Tamas Kerekes ◽  
Dezso Sera
Keyword(s):  
Experimental Tests ◽  
Energy Yield ◽  
Power Electronic ◽  
Solar Pv ◽  
Partial Shading ◽  
Loss Analysis ◽  
Pv Systems ◽  
Pv Module ◽  
Pv Modules ◽  
In Series

Partial shading affects the energy harvested from photovoltaic (PV) modules, leading to a mismatch in PV systems and causing energy losses. For this purpose, differential power processing (DPP) converters are the emerging power electronic-based topologies used to address the mismatch issues. Normally, PV modules are connected in series and DPP converters are used to extract the power from these PV modules by only processing the fraction of power called mismatched power. In this work, a switched-capacitor-inductor (SCL)-based DPP converter is presented, which mitigates the non-ideal conditions in solar PV systems. A proposed SCL-based DPP technique utilizes a simple control strategy to extract the maximum power from the partially shaded PV modules by only processing a fraction of the power. Furthermore, an operational principle and loss analysis for the proposed converter is presented. The proposed topology is examined and compared with the traditional bypass diode technique through simulations and experimental tests. The efficiency of the proposed DPP is validated by the experiment and simulation. The results demonstrate the performance in terms of higher energy yield without bypassing the low-producing PV module by using a simple control. The results indicate that achieved efficiency is higher than 98% under severe mismatch (higher than 50%).

scholarly journals Modeling and Relative Research of Solar Photovoltaic Array Topologies Under Partial Shading Conditions

2019 ◽  
Vol 8 (11) ◽  
pp. 340-346
Keyword(s):  
Fill Factor ◽  
Electrical Power ◽  
Solar Photovoltaic ◽  
Power Losses ◽  
Partial Shading ◽  
Photovoltaic Array ◽  
Pv Array ◽  
Pv Module ◽  
And Performance ◽  
Zigzag Type

The electrical power generation from solar photo voltaic arrays increases by reducing partial shading effect due to the deposition of dust in modules, shadow of nearby buildings, cloud coverage leads to mismatching power losses. This paper gives the detailed analysis of modeling, simulation and performance analysis of different 4x4 size PV array topologies under different irradiance levels and to extract output power of panels maximum by reducing the mismatching power losses. For this analysis, a comparative study of six PV array topologies are Series, Parallel, Series-Parallel, Total-Cross-Tied, Bridge Linked and Honey-Comb are considered under various shading conditions such as one module shading, one string shading, zigzag type partial shading and total PV array partially shaded cases. The performance of above six topologies are compare with mismatching power losses and fill-factor. For designing and simulation of different PV array configurations/topologies in MaTLab/Simulink, the LG Electronics LG215P1W PV module parameters are used in all PV modules.

The Impact Mitigation of Partial Shading on PV Array Power Generation

2015 ◽  
Vol 781 ◽  
pp. 267-271
Author(s):  
Santisouk Phiouthonekham ◽  
Anucha Lekkruasuwan ◽  
Surachai Chaitusaney
Keyword(s):  
Power Generation ◽  
Solar Irradiation ◽  
Testing System ◽  
Partial Shading ◽  
Pv Array ◽  
Pv Module ◽  
Time Period ◽  
Current Voltage ◽  
Pv Modules ◽  
The Impact

The impact of partial shading on photovoltaic (PV) array is discussed in this paper. The partial shading on PV array can significantly decrease the power generation of PV array. This study examines the modeling of PV module which relates with solar irradiation, temperature, and shading pattern. There are different shading patterns on PV array, such as one-string shading, two-strings shading, and much more. The characteristics of current-voltage (I-V) and voltage-power (V-P) curves for each individual the PV array can be different dependent on the multiple MPPs, maximum power points (MPPs). These multiple MPPs are basically lower than the MPP in case of no shading. Therefore, the total generated energy in an interested time period is usually reduced. As a result, this paper proposes the appropriate arrangement of PV modules in a PV array in order to mitigate the impact of partial shading. Finally, the proposed arrangement of PV modules is tested in a testing system. All the obtained results confirms that the proposed arrangement of PV modules is effective and can be applied in practice.

scholarly journals Performance Analysis of Conventional, Hybrid and Optimal PV Array Configurations of Partially Shaded Modules

2019 ◽  
Vol 9 (1) ◽  
pp. 3061-3073
Keyword(s):  
Performance Analysis ◽  
Solar Pv ◽  
Partial Shading ◽  
Power Number ◽  
Matlab Simulink ◽  
Pv Array ◽  
Pv Module ◽  
And Performance

In this paper, modeling and performance analysis of conventional configurations are Series-Parallel (SP), BridgeLinked (BL), Honey-Comb (HC), Total-Cross-Tied(TCT) and proposed hybrid configurations are SP-TCT, BL-TCT, HC-TCT, BL-HC and modified BL(MBL), modified HC(MHC), proposed optimal interconnection type configurations of a 5x5 size solar PV array under ten different partial shading cases it causes shading losses and compare the best configuration with respect to array power, number of interconnections or ties required between shaded modules in the array. The proposed optimal interconnection method reduces the number of ties required between modules and these ties are based on the position of number of shaded modules in the entire solar PV array. For the performance analysis of above 11 configurations, total ten shading cases are considered and compare the result with one un-shaded case-U of an irradiance 1000 W/m2 . The PV module parameters of Vikram Solar ELDORA 270 are used for modeling of above 11 conventional and proposed PV array configurations and simulate the models in MATLAB/ Simulink software.

scholarly journals Current Flow Analysis of PV Arrays under Voltage Mismatch Conditions and an Inverter Failure

2019 ◽  
Vol 9 (23) ◽  
pp. 5163 ◽  
Author(s):  
Woo Gyun Shin ◽  
Jong Rok Lim ◽  
Gi Hwan Kang ◽  
Young Chul Ju ◽  
Hye Mi Hwang ◽  
...  
Keyword(s):  
Current Flow ◽  
Flow Analysis ◽  
Reverse Current ◽  
Open Circuit ◽  
Electrical Characteristics ◽  
Partial Shading ◽  
Pv Array ◽  
Pv Module ◽  
Parallel Circuits ◽  
Pv Modules

In PV (Photovoltaic) systems, the PV array is a structure in which many PV strings are connected in parallel. The voltage mismatch between PV strings, in which PV modules are connected in a series, occurs due to a voltage decrease in some modules. In this paper, research on the electrical characteristics of PV arrays due to a voltage mismatch was conducted. Considering the voltage mismatch, experiments on partial shading, the non-uniformity of irradiance, and the failure of bypass diodes were conducted on the PV module level. It was confirmed that the open-circuit voltage greatly decreased due to the failure of bypass diodes, which is among the causes of voltage mismatch. From the simulation results at the PV array level, it can be seen that a reverse current flowed into the low-potential string, which includes PV modules, causing the failure of the bypass diodes. Measuring the reverse current at one low-potential string, it was found that, in four parallel circuits, the reverse current was 12 A. For this reason, in large PV plants, an overcurrent can flow into the fuse due to the potential difference between strings, causing an output decrease of PV plants and the burnout of fuses.

scholarly journals Experimental Investigation of PV Array Interconnection Topologies at Nonuniform Aging Condition for Power Maximization

2020 ◽  
Vol 6 (1) ◽  
pp. 39-45
Author(s):  
AA Mansur ◽  
MAU Haq ◽  
Md H Maruf ◽  
ASM Shihavuddin ◽  
Md R Amin ◽  
...  
Keyword(s):  
Output Power ◽  
Power Production ◽  
Aging Condition ◽  
Science And Engineering ◽  
Pv Array ◽  
Pv Module ◽  
Current Voltage ◽  
Pv Modules ◽  
Power Maximization ◽  
Array Output

In vast Photovoltaic (PV) power plant the output power production decreases significantly due to the fact of non-uniform aging of PV modules. The non-uniform aging of PV modules increases current-voltage (I-V) mismatch among the array modules and causes mismatch power loss (MPL). There are different interconnection topologies of the PV module in an array to minimize MPL and thus maximize the array output power. This paper investigates four different interconnection topologies experimentally on a 4×4 nonuniformly aged PV array. Three different patterns of PV module rearrangement are used to investigate the performance of each interconnection topology in terms of array output power and MPL. The experimental results show that the proposed interconnection topology is yields about 3.28% (average) higher output power than that of the most commonly used series-parallel array topology. GUB JOURNAL OF SCIENCE AND ENGINEERING, Vol 6(1), Dec 2019 P 39-45

Performance Analysis of Partially Shaded Photovoltaic Array Using Magic Square View Configuration for Shade Dispersion

2020 ◽  
Vol 142 (6) ◽  
Author(s):  
Lahcen El Iysaouy ◽  
Mhammed Lahbabi ◽  
Algirdas Baskys ◽  
Abdelmajid Oumnad
Keyword(s):  
Performance Analysis ◽  
Partial Shading ◽  
Magic Square ◽  
Multiple Peaks ◽  
Photovoltaic Array ◽  
Pv Array ◽  
Bird Droppings ◽  
Pv Modules ◽  
And Performance ◽  
Power Point

Abstract The power generated by the photovoltaic (PV) array is affected by the partial shading, caused by the neighboring object shadows, dirtiness, moving clouds, bird droppings, different orientation angles of PV modules, deposition of dust in modules, and the physical location of the PV module. Therefore, the PV systems exhibit multiple peaks of generated power and do not always track the maximum power point (MPP). Thus, to overcome these problems of multiple peaks, the PV panels are reconfigured using either electrical or physical reconfiguration methods. The main aim of this paper is to investigate the performance of magic square view (MSV) configuration of PV modules under partial shading conditions (PSCs). For validation, three kinds of PSCs patterns are considered and are then compared to the Total Cross Tied (TCT) and Sudoku (SDK) configurations: long and wide, short and narrow, and long and narrow. Overall, the obtained results show that the MSV configuration allows us to increase the power generated by the PV array by 34% and 7% under the three types of shadow studied as compared to the TCT and SDK configurations, respectively. The PV array configurations parameters are performed based on matlab/simulink software. The simulation and performance analysis of PV array configurations is performed with 81 PV modules of BP Solar Poly BP 380 modules.

scholarly journals Mathematical Model for Regular and Irregular PV Arrays with Improved Calculation Speed

2020 ◽  
Vol 12 (24) ◽  
pp. 10684
Author(s):  
Luz Adriana Trejos-Grisales ◽  
Juan David Bastidas-Rodríguez ◽  
Carlos Andrés Ramos-Paja
Keyword(s):  
Mathematical Model ◽  
Prediction Accuracy ◽  
Power Production ◽  
Pv System ◽  
Partial Shading ◽  
Pv Systems ◽  
Pv Array ◽  
Inflection Points ◽  
Higher Power ◽  
General Mathematical Model

Photovoltaic (PV) systems are usually developed by configuring the PV arrays with regular connection schemes, such as series-parallel, total cross-tied, bridge-linked, among others. Such a strategy is aimed at increasing the power that is generated by the PV system under partial shading conditions, since the power production changes depending on the connection scheme. Moreover, irregular and non-common connection schemes could provide higher power production for irregular (but realistic) shading conditions that aere caused by threes or other objects. However, there are few mathematical models that are able to predict the power production of different configurations and reproduce the behavior of both regular and irregular PV arrays. Those general array models are slow due to the large amount of computations that are needed to find the PV current for a given PV voltage. Therefore, this paper proposes a general mathematical model to predict the power production of regular and irregular PV arrays, which provides a faster calculation in comparison with the general models that were reported in the literature, but without reducing the prediction accuracy. The proposed modeling approach is based on detecting the inflection points that are caused by the bypass diodes activation, which enables to narrow the range in which the modules voltages are searched, thus reducing the calculation time. Therefore, this fast model is useful in designing the fixed connections of PV arrays that are subjected to shading conditions, in order to reconfigure the PV array in real-time, depending on the shading pattern, among other applications. The proposed solution is validated by comparing the results with another general model and with a circuital implementation of the PV system.

scholarly journals Study on the Influence of Mounting Dimensions of PV Array on Module Temperature in Open-Joint Photovoltaic Ventilated Double-Skin Façades

2021 ◽  
Vol 13 (9) ◽  
pp. 5027
Author(s):  
Wenjie Zhang ◽  
Tongdan Gong ◽  
Shengbing Ma ◽  
Jianwei Zhou ◽  
Yingbo Zhao
Keyword(s):  
Heat Dissipation ◽  
Temperature Drop ◽  
Vertical Direction ◽  
Wind Pressure ◽  
Pv Array ◽  
Pv Module ◽  
Pv Modules ◽  
Double Skin ◽  
Open Joint ◽  
Double Skin Facades

In building integrated photovoltaics (PV), it is important to solve the heat dissipation problem of PV modules. In this paper, the computational fluid dynamics (CFD) method is used to simulate the flow field around the open-joint photovoltaic ventilated double-skin façades (OJ-PV-DSF) to study the influence of the mounting dimensions (MD) of a PV array on the module temperature. The typical summer afternoon meteorological parameters, such as the total radiation (715.4 W/m2), the outdoor temperature (33.1 °C), and the wind speed (2.0 m/s), etc., are taken as input parameters. With the DO (discrete ordinates) model and the RNG (renormalization-group) k − ε model, a steady state calculation is carried out to simulate the flow of air in and around the cavity under the coupling of hot pressure and wind pressure, thereby obtaining the temperature distribution of the PV array and the wall. In addition, the simulation results are compared with the onsite experimental data and thermal imaging to verify the accuracy of the CFD model. Then three MD of the open joints are discussed. The results show that when the a value (represents the distance between PV modules and wall) changes from 0.05 to 0.15, the temperature drop of the PV module is the most obvious, reaching 2.0 K. When the b value (representing the distance between two adjacent PV modules in the vertical direction) changes from 0 to 0.1, the temperature drop of the PV module is most obvious, reaching 1 K. When the c value (represents the distance between two adjacent PV modules in the horizontal direction) changes from 0 to 0.1, the temperature of the PV module is lowered by 0.8 K. Thus, a = 0.1–0.15, b = 0.1 and c = 0.1 are recommended for engineering applications to effectively reduce the module temperature.

Sign in / Sign up

Export Citation Format

Share Document