scholarly journals Enhancement and Validation of a 3D-Printed Solid Target Holder at a Cyclotron Facility in Perth, Australia

Instruments ◽  
2019 ◽  
Vol 3 (1) ◽  
pp. 12 ◽  
Author(s):  
Sun Chan ◽  
David Cryer ◽  
Roger I. Price
Keyword(s):  
Thermal Conductivity ◽  
Cast Alloy ◽  
Cost Effective ◽  
Solid Target ◽  
Cooling Efficiency ◽  
Proof Of Concept ◽  
Proton Bombardment ◽  
Target Holder ◽  
3D Printed ◽  
Target Design

A 3D-printed metal solid target using additive manufacturing process is a cost-effective production solution to complex and intricate target design. The initial proof-of-concept prototype solid target holder was 3D-printed in cast alloy, Al–7Si–0.6Mg (A357). However, given the relatively low thermal conductivity for A357 (max, 160 W/m·K), replication of the solid target holder in sterling silver (SS925) with higher thermal conductivity (max, 361 W/m·K) was investigated. The SS925 target holder enhances the cooling efficiency of the target design, thus achieving higher target current during irradiation. A validation production of 64Cu using the 3D-printed SS925 target holder indicated no loss of enriched 64Ni from proton bombardment above 80 µA, at 11.5 MeV.

scholarly journals Vent-Lock: A 3D Printed Ventilator Multiplexer to Enhance the Capacity of Treating Patients with COVID-19

2020 ◽  
Author(s):  
Helen Xun ◽  
Christopher Shallal ◽  
Justin Unger ◽  
Runhan Tao ◽  
Alberto Torres ◽  
...  
Keyword(s):  
Distress Syndrome ◽  
De Novo ◽  
Cost Effective ◽  
The Novel ◽  
Proof Of Concept ◽  
Mechanical Ventilators ◽  
Respiratory Therapists ◽  
Flow Restriction ◽  
3D Printed ◽  
Critical Components

Mechanical ventilators are essential to patients who become critically ill from acute respiratory distress syndrome (ARDS), and shortages have been reported due to the novel severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). We utilized cost-effective, on-demand 3D printing (3DP) technology to produce critical components for a novel ventilator multiplexer system, Vent-Lock, to split one ventilator or anesthesia gas machine between two patients. FloRest, a novel 3DP flow restrictor, provides clinicians control of tidal volumes and positive end expiratory pressure (PEEP), using the 3DP manometer adaptor to monitor pressures. We tested the ventilator splitter circuit in simulation centers between artificial lungs and used an anesthesia gas machine to successfully ventilate two swines. As one of the first studies to demonstrate splitting one anesthesia gas machine between two swines, we present proof-of-concept of a de novo, closed, multiplexing system, with flow restriction for individualized patient therapy. Our studies underscore that while possible, ventilator multiplexing is a complicated synergy between machine settings, circuit modification, and patient monitoring. Consequently, ventilator multiplexing is reserved only as a last emergency resource, by trained clinicians and respiratory therapists with ventilator operative experience.

scholarly journals Improving Cooling Performance of Injection Molding Tool with Conformal Cooling Channel by Adding Hybrid Fillers

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1224
Author(s):  
Chil-Chyuan Kuo ◽  
Wei-Hua Chen
Keyword(s):  
Thermal Conductivity ◽  
Injection Molding ◽  
Cooling Time ◽  
Performance Ratio ◽  
Cooling Efficiency ◽  
Cooling Channel ◽  
Conformal Cooling Channel ◽  
Conformal Cooling ◽  
Fused Deposition ◽  
Silicone Rubber Mold

Silicone rubber mold (SRM) is capable of reducing the cost and time in a new product development phase and has many applications for the pilot runs. Unfortunately, the SRM after injection molding has a poor cooling efficiency due to its low thermal conductivity. To improve the cooling efficiency, the thermal conductivity of the SRM was improved by adding fillers into the SRM. An optimal recipe for fabricating a high cooling efficiency low-pressure injection mold with conformal cooling channel fabricated by fused deposition modeling technology was proposed and implemented. This study proposes a recipe combining 52.6 wt.% aluminum powder, 5.3 wt.% graphite powder, and 42.1 wt.% liquid silicon rubber can be used to make SRM with excellent cooling efficiency. The price–performance ratio of this SRM made by the proposed recipe is around 55. The thermal conductivity of the SRM made by the proposed recipe can be increased by up to 77.6% compared with convention SRM. In addition, the actual cooling time of the injection molded product can be shortened up to 69.1% compared with the conventional SRM. The actual cooling time obtained by the experiment is in good agreement with the simulation results with the relative error rate about 20%.

scholarly journals 3D printed microfluidic lab-on-a-chip device for fiber-based dual beam optical manipulation

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Haoran Wang ◽  
Anton Enders ◽  
John-Alexander Preuss ◽  
Janina Bahnemann ◽  
Alexander Heisterkamp ◽  
...  
Keyword(s):  
Optical Fibers ◽  
Single Cells ◽  
Lab On A Chip ◽  
Cost Effective ◽  
Optical Manipulation ◽  
Hydrodynamic Focusing ◽  
Trapping Region ◽  
Dual Beam ◽  
3D Printed ◽  
On Chip

Abstract3D printing of microfluidic lab-on-a-chip devices enables rapid prototyping of robust and complex structures. In this work, we designed and fabricated a 3D printed lab-on-a-chip device for fiber-based dual beam optical manipulation. The final 3D printed chip offers three key features, such as (1) an optimized fiber channel design for precise alignment of optical fibers, (2) an optically clear window to visualize the trapping region, and (3) a sample channel which facilitates hydrodynamic focusing of samples. A square zig–zag structure incorporated in the sample channel increases the number of particles at the trapping site and focuses the cells and particles during experiments when operating the chip at low Reynolds number. To evaluate the performance of the device for optical manipulation, we implemented on-chip, fiber-based optical trapping of different-sized microscopic particles and performed trap stiffness measurements. In addition, optical stretching of MCF-7 cells was successfully accomplished for the purpose of studying the effects of a cytochalasin metabolite, pyrichalasin H, on cell elasticity. We observed distinct changes in the deformability of single cells treated with pyrichalasin H compared to untreated cells. These results demonstrate that 3D printed microfluidic lab-on-a-chip devices offer a cost-effective and customizable platform for applications in optical manipulation.

scholarly journals Design of Thermal Insulation Materials with Different Geometries of Channels

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2217
Author(s):  
Daniela Șova ◽  
Mariana Domnica Stanciu ◽  
Sergiu Valeriu Georgescu
Keyword(s):  
Thermal Conductivity ◽  
Porous Structure ◽  
Base Material ◽  
Cost Effective ◽  
Heat Radiation ◽  
Average Temperature ◽  
Temperature Regimes ◽  
The Face ◽  
Inclined Channels ◽  
Air Channels

Investigating the large number of various materials now available, some materials scientists promoted a method of combining existing materials with geometric features. By studying natural materials, the performance of simple constituent materials is improved by manipulating their internal geometry; as such, any base material can be used by performing millimeter-scale air channels. The porous structure obtained utilizes the low thermal conductivity of the gas in the pores. At the same time, heat radiation and gas convection is hindered by the solid structure. The solution that was proposed in this research for obtaining a material with porous structure consisted in perforating extruded polystyrene (XPS) panels, as base material. Perforation was performed horizontally and at an angle of 45 degrees related to the face panel. The method is simple and cost-effective. Perforated and simple XPS panels were subjected to three different temperature regimes in order to measure the thermal conductivity. There was an increase in thermal conductivity with the increase in average temperature in all studied cases. The presence of air channels reduced the thermal conductivity of the perforated panels. The reduction was more significant at the panels with inclined channels. The differences between the thermal conductivity of simple XPS and perforated XPS panels are small, but the latter can be improved by increasing the number of channels and the air channels’ diameter. Additionally, the higher the thermal conductivity of the base material, the more significant is the presence of the channels, reducing the effective thermal conductivity. A base material with low emissivity may also reduce the thermal conductivity.

scholarly journals Preparation and Performance Evaluation of Duotone 3D-Printed Polyetheretherketone as Oral Prosthetic Materials: A Proof-of-Concept Study

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1949
Author(s):  
Ling Ding ◽  
Wei Lu ◽  
Jiaqi Zhang ◽  
Chuncheng Yang ◽  
Guofeng Wu
Keyword(s):  
Titanium Dioxide ◽  
Performance Evaluation ◽  
Mechanical Performance ◽  
Mechanical Tests ◽  
Flexural Properties ◽  
Proof Of Concept ◽  
Tooth Color ◽  
Dental Application ◽  
3D Printed ◽  
And Performance

Literature has reported the successful use of 3D printed polyetheretherketone (PEEK) to fabricate human body implants and oral prostheses. However, the current 3D printed PEEK (brown color) cannot mimic the vivid color of oral tissues and thus cannot meet the esthetical need for dental application. Therefore, titanium dioxide (TiO2) and ferric oxide (Fe2O3) were incorporated into PEEK to prepare a series of tooth-color and gingival-color PEEK composites in this study. Through color measurements and mechanical tests, the color value and mechanical performance of the 3D printed PEEK composites were evaluated. In addition, duotone PEEK specimens were printed by a double nozzle with an interface between tooth-color and gingival-color parts. The mechanical performance of duotone PEEK with two different interfaces (horizontal and vertical) was investigated. With the addition of TiO2 and Fe2O3, the colors of 3D printed PEEK composites become closer to that of dental shade guides. 3D printed PEEK composites generally demonstrated superior tensile and flexural properties and hence have great potential in the dental application. In addition, duotone 3D printed PEEK with a horizontal interfacial orientation presented better mechanical performance than that with a vertical one.

scholarly journals 3D Printed Imaging Platform for Portable Cell Counting

The Analyst ◽  
2021 ◽  
Author(s):  
Diwakar M. Awate ◽  
Cicero C. Pola ◽  
Erica Shumaker ◽  
Carmen L Gomes ◽  
Jaime Javier Juarez
Keyword(s):  
3D Printing ◽  
Point Of Care ◽  
Cost Effective ◽  
Cell Counting ◽  
Biomedical Sciences ◽  
Widespread Application ◽  
Resource Limited ◽  
Cost Effective Approach ◽  
3D Printed

Despite having widespread application in the biomedical sciences, flow cytometers have several limitations that prevent their application to point-of-care (POC) diagnostics in resource-limited environments. 3D printing provides a cost-effective approach...

Design of 3D printed bioinspired nacre-like structured materials with significantly enhanced thermal conductivity

2021 ◽  
Vol 118 (13) ◽  
pp. 131903
Author(s):  
Haohuan Wang ◽  
Zhengyong Huang ◽  
Jian Li ◽  
Feipeng Wang ◽  
Zhanzu Feng ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Structured Materials ◽  
3D Printed ◽  
Enhanced Thermal Conductivity

scholarly journals Effects of Rice Straw Powder (RSP) Size and Pretreatment on Properties of FDM 3D-Printed RSP/Poly(Lactic Acid) Biocomposites

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3234
Author(s):  
Wangwang Yu ◽  
Lili Dong ◽  
Wen Lei ◽  
Yuhan Zhou ◽  
Yongzhe Pu ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Rice Straw ◽  
Fused Deposition Modeling ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Cost Effective ◽  
Poly Lactic Acid ◽  
Fused Deposition ◽  
Interfacial Compatibility ◽  
3D Printed

To develop a new kind of environment-friendly composite filament for fused deposition modeling (FDM) 3D printing, rice straw powder (RSP)/poly(lactic acid) (PLA) biocomposites were FDM-3D-printed, and the effects of the particle size and pretreatment of RSP on the properties of RSP/PLA biocomposites were investigated. The results indicated that the 120-mesh RSP/PLA biocomposites (named 120#RSP/PLA) showed better performance than RSP/PLA biocomposites prepared with other RSP sizes. Infrared results showed that pretreatment of RSP by different methods was successful, and scanning electron microscopy indicated that composites prepared after pretreatment exhibited good interfacial compatibility due to a preferable binding force between fiber and matrix. When RSP was synergistically pretreated by alkaline and ultrasound, the composite exhibited a high tensile strength, tensile modulus, flexural strength, and flexural modulus of 58.59, 568.68, 90.32, and 3218.12 MPa, respectively, reflecting an increase of 31.19%, 16.48%, 18.75%, and 25.27%, respectively, compared with unmodified 120#RSP/PLA. Pretreatment of RSP also improved the thermal stability and hydrophobic properties, while reducing the water absorption of 120#RSP/PLA. This work is believed to provide highlights of the development of cost-effective biocomposite filaments and improvement of the properties of FDM parts.

scholarly journals Polycrystalline SnSe with a thermoelectric figure of merit greater than the single crystal

2021 ◽  
Author(s):  
Chongjian Zhou ◽  
Yong Kyu Lee ◽  
Yuan Yu ◽  
Sejin Byun ◽  
Zhong-Zhen Luo ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Single Crystal ◽  
High Performance ◽  
Figure Of Merit ◽  
Waste Heat ◽  
Electric Energy ◽  
Cost Effective ◽  
Tin Selenide ◽  
Tin Oxides ◽  
Thermally Conductive

AbstractThermoelectric materials generate electric energy from waste heat, with conversion efficiency governed by the dimensionless figure of merit, ZT. Single-crystal tin selenide (SnSe) was discovered to exhibit a high ZT of roughly 2.2–2.6 at 913 K, but more practical and deployable polycrystal versions of the same compound suffer from much poorer overall ZT, thereby thwarting prospects for cost-effective lead-free thermoelectrics. The poor polycrystal bulk performance is attributed to traces of tin oxides covering the surface of SnSe powders, which increases thermal conductivity, reduces electrical conductivity and thereby reduces ZT. Here, we report that hole-doped SnSe polycrystalline samples with reagents carefully purified and tin oxides removed exhibit an ZT of roughly 3.1 at 783 K. Its lattice thermal conductivity is ultralow at roughly 0.07 W m–1 K–1 at 783 K, lower than the single crystals. The path to ultrahigh thermoelectric performance in polycrystalline samples is the proper removal of the deleterious thermally conductive oxides from the surface of SnSe grains. These results could open an era of high-performance practical thermoelectrics from this high-performance material.

scholarly journals Rapid Production of PDMS Microdevices for Electrodriven Separations and Microfluidics by 3D-Printed Scaffold Removal

Separations ◽  
2021 ◽  
Vol 8 (5) ◽  
pp. 67
Author(s):  
Alena Šustková ◽  
Klára Konderlová ◽  
Ester Drastíková ◽  
Stefan Sützl ◽  
Lenka Hárendarčíková ◽  
...  
Keyword(s):  
Organic Dyes ◽  
Microfluidic Devices ◽  
Proof Of Concept ◽  
Magnetic Microparticles ◽  
Mechanical Removal ◽  
Glass Slides ◽  
Rapid Production ◽  
3D Printed

In our work, we produced PDMS-based microfluidic devices by mechanical removal of 3D-printed scaffolds inserted in PDMS. Two setups leading to the fabrication of monolithic PDMS-based microdevices and bonded (or stamped) PDMS-based microdevices were designed. In the monolithic devices, the 3D-printed scaffolds were fully inserted in the PDMS and then carefully removed. The bonded devices were produced by forming imprints of the 3D-printed scaffolds in PDMS, followed by bonding the PDMS parts to glass slides. All these microfluidic devices were then successfully employed in three proof-of-concept applications: capture of magnetic microparticles, formation of droplets, and isotachophoresis separation of model organic dyes.

Sign in / Sign up

Export Citation Format

Share Document