scholarly journals Assessment of the Impact of the Addition of Nanoparticles on the Properties of Glass–Ionomer Cements

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 276 ◽  
Author(s):  
Elizabeta Gjorgievska ◽  
John W. Nicholson ◽  
Dragana Gabrić ◽  
Zeynep Asli Guclu ◽  
Ivana Miletić ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Compressive Strength ◽  
Tio2 Nanoparticles ◽  
Emission Spectrometry ◽  
Al2o3 Nanoparticles ◽  
Glass Ionomer Cements ◽  
Glass Ionomer ◽  
The Impact ◽  
Scanning Electron

The aim of the study was to evaluate the effects of incorporation of Al2O3, ZrO2 and TiO2 nanoparticles into glass–ionomer cements (GICs). Two different GICs were used in the study. Four groups were prepared for each material: the control group (without nanoparticles) and three groups modified by the incorporation of nanoparticles at 2, 5 or 10 wt %, respectively. Cements were mixed and placed in moulds (4 mm × 6 mm); after setting, the samples were stored in saline (one day and one week). Compressive strengths were measured and the morphology of the fractured surfaces was analyzed by scanning electron microscopy. The elements released into the storage solutions were determined by Inductively coupled plasma-optical emission spectrometry (ICP-OES). Addition of nanoparticles was found to alter the appearance of cements as examined by scanning electron microscopy. Compressive strength increased with the addition of ZrO2 and especially TiO2 nanoparticles, whereas the addition of Al2O3 nanoparticles generally weakened the cements. The ion release profile of the modified cements was the same in all cases. The addition of Al2O3, ZrO2 and TiO2 nanoparticles into GICs is beneficial, since it leads to reduction of the microscopic voids in the set cement. Of these, the use of ZrO2 and TiO2 nanoparticles also led to increased compressive strength. Nanoparticles did not release detectable levels of ions (Al, Zr or Ti), which makes them suitable for clinical use.

scholarly journals Chemical and Structural Characterization of Glass Ionomer Cements indicated for Atraumatic Restorative Treatment

2015 ◽  
Vol 16 (1) ◽  
pp. 61-67 ◽  
Author(s):  
Alvaro Henrique Borges ◽  
Matheus Coelho Bandéca ◽  
Orlando Aguirre Guedes ◽  
Mariana Kyosen Nakatani ◽  
Cyntia Rodrigues de Araújo Estrela ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Surface Morphology ◽  
Atraumatic Restorative Treatment ◽  
Glass Ionomer Cements ◽  
Glass Ionomer ◽  
Restorative Treatment ◽  
Chemical Constitution ◽  
Scanning Electron

ABSTRACT Glass ionomer cements (GICs) are restorative materials, which clinical use has increased significantly during the last decade. The aim of the present study was to analyze the chemical constitution and surface morphology of four glass ionomer cements: Maxxion R, VitroFill, Vidrion R and Vitremer. Twelve polyethylene tubes with an internal diameter of 3 and 3 mm in length were prepared, filled and then transferred to a chamber with 95% relative humidity and a temperature of 37°C. The surface morphology of the tested materials was examined by scanning electron microscopy (SEM) and main components were investigated by energy-dispersive X-ray microanalysis (EDX). Scanning electron microscopy revealed irregular and rough external surface. Cracking was not observed. The main constituents were found to be aluminum, silicon, calcium, sodium and fluoride. Phosphorus, sulfur and barium were only observed in Vidrion R, while chlorine were only observed in Maxxion R. Elemental mapping of the outer surface revealed high concentration of aluminum and silicon. Significant irregularities on the surface of the tested materials were observed. The chemical constitution of all GIC was similar. How to cite this article Guedes OA, Borges ÁH, Bandeca MC, Nakatani MK, de Araújo Estrela CR, de Alencar AHG, Estrela C. Chemical and Structural Characterization of Glass Ionomer Cements indicated for Atraumatic Restorative Treatment. J Contemp Dent Pract 2015;16(1):61-67.

Effect of inorganic nanofillers on the impact behavior and fracture probability of industrial high-density polyethylene nanocomposite

2017 ◽  
Vol 52 (18) ◽  
pp. 2431-2442 ◽  
Author(s):  
Harun Sepet ◽  
Necmettin Tarakcioglu ◽  
RDK Misra
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Density Polyethylene ◽  
Fracture Probability ◽  
High Density ◽  
Impact Behavior ◽  
Inorganic Filler ◽  
Melt Mixing ◽  
The Impact ◽  
Scanning Electron

The main purpose of this work is to study how the morphology of nanofillers and dispersion and distribution level of inorganic nanofiller influence the impact behavior and fracture probability of inorganic filler filled industrial high-density polyethylene nanocomposites. For this study, nanoclay and nano-CaCO3 fillers–high-density polyethylene mixings (0, 1, 3, 5 wt.% high-density polyethylene) was prepared by melt-mixing method using a compounder system. The impact behavior was examined by charpy impact test, scanning electron microscopy, and probability theory and statistics. The level of the dispersion was characterized with scanning electron microscopy energy dispersive X-ray spectroscopy analysis. The results showed rather good dispersion of both of inorganic nanofiller, with a mixture of exfoliated and confined morphology. The results indicated that the impact strength of the industrial nanocomposite decreased with the increase of inorganic particulate content. The impact reliability of the industrial nanocomposites depends on the type of nanofillers and their dispersion and distribution in the matrix.

Direct Determination of Apatite in Lake Sediments

1980 ◽  
Vol 37 (4) ◽  
pp. 640-646 ◽  
Author(s):  
R. P. Reid ◽  
C. H. Pharo ◽  
W. C. Barnes
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Lake Sediments ◽  
Trophic State ◽  
Inorganic Phosphorus ◽  
Source Rocks ◽  
Emission Spectrometry ◽  
Phosphorus Load ◽  
Lake Trophic State ◽  
Scanning Electron

Apatite is a common accessory mineral in the source rocks for the glacial debris supplying sediments to many Canadian lakes. A method has been developed which uses scanning electron microscopy and energy dispersive X-ray emission spectrometry for direct identification of apatite. This method has been used to examine the apatite content of various size fractions in Kamloops Lake sediments. Apatite concentrations obtained by this direct examination correlate well (r > 0.999) with apatite concentrations determined by chemical analyses and indicate that, in addition to comprising as much as 70% of the total phosphorus load, apatite may comprise as much as one-third of the "dissolved" (< 0.45 μm) inorganic phosphorus load. Consequently the use of classical (e.g. Vollenweider 1968; Vollenweider and Dillon 1974) methods of estimating lake trophic state from inorganic phosphorus concentrations in lake water must be done with care, recognizing that the bulk of inorganic phosphorus in lakes deriving sediment from glaciated igneous or metamorphic terrains may be in the form of apatite.Key words: apatite, lake, trophic state, phosphorus load, scanning electron microscopy

scholarly journals CHEMICAL AND PHISICAL CHARACTERIZATION OF MEMORY BOARDS FROM OBSOLETE COMPUTERS THROUGH OPTICAL EMISSION SPECTROMETRY AND SCANNING ELECTRON MICROSCOPY

2019 ◽  
Vol 16 (2) ◽  
pp. 212-221
Author(s):  
Marcos Paulo Kohler Caldas ◽  
Mariana Alves de Carvalho ◽  
Viviane Tavares de Moraes ◽  
Jorge Alberto Soares Tenório ◽  
Denise Crocce Romano Espinosa
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Optical Emission ◽  
Optical Emission Spectrometry ◽  
Emission Spectrometry ◽  
Scanning Electron

The Impact Properties of a Polyurethane Composite Filled with Clay

2011 ◽  
Vol 197-198 ◽  
pp. 1100-1103
Author(s):  
Jian Li
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Mechanical Analysis ◽  
Impact Testing ◽  
Impact Properties ◽  
Polyurethane Composite ◽  
The Matrix ◽  
The Impact ◽  
Scanning Electron

A polyurethane/clay (PU/clay) composite was synthesized. The microstructure of the composite was examined by scanning electron microscopy. The impact properties of the composite were characterized by impact testing. The study on the structure of the composite showed that clays could be dispersed in the polymer matrix well apart from a few of clusters. The results from mechanical analysis indicated that the impact properties of the composite were increased greatly in comparison with pure polyurethane. The investigation on the mechanical properties showed that the impact strength could be obviously increased by adding 20 wt% (by weight) clay to the matrix.

UTILIZATION OF FLY ASH AND CONCRETE RESIDUE IN THE PRODUCTION OF GEOPOLYMER BRICKS

2017 ◽  
Vol 12 (1) ◽  
pp. 63-77 ◽  
Author(s):  
Siriporn Sirikingkaew ◽  
Nuta Supakata
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Compressive Strength ◽  
Phase Composition ◽  
Fly Ash ◽  
Industrial Waste ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

This study presents the development of geopolymer bricks synthetized from industrial waste, including fly ash mixed with concrete residue containing aluminosilicate compound. The above two ingredients are mixed according to five ratios: 100:0, 95:5, 90:10, 85:15, and 80:20. The mixture's physico-mechanical properties, in terms of water absorption and the compressive strength of the geopolymer bricks, are investigated according to the TIS 168-2546 standard. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses are used to investigate the microstructure and the elemental and phase composition of the brick specimens. The results indicate that the combination of fly ash and concrete residue represents a suitable approach to brick production, as required by the TIS 168–2546 standard.

scholarly journals Microstructure–Property Relationship of Polyurethane Foams Modified with Baltic Sea Biomass: Microcomputed Tomography vs. Scanning Electron Microscopy

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5734
Author(s):  
Paulina Kosmela ◽  
Jan Suchorzewski ◽  
Krzysztof Formela ◽  
Paweł Kazimierski ◽  
Józef Tadeusz Haponiuk ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Baltic Sea ◽  
Thermal Insulation ◽  
Reference Sample ◽  
Microcomputed Tomography ◽  
Polyurethane Foams ◽  
Relationship Of ◽  
The Impact ◽  
Scanning Electron

In this paper, novel rigid polyurethane foams modified with Baltic Sea biomass were compared with traditional petro-based polyurethane foam as reference sample. A special attention was focused on complex studies of microstructure, which was visualized and measured in 3D with high-resolution microcomputed tomography (microCT) and, as commonly applied for this purpose, scanning electron microscopy (SEM). The impact of pore volume, area, shape and orientation on appearance density and thermal insulation properties of polyurethane foams was determined. The results presented in the paper confirm that microcomputed tomography is a useful tool for relatively quick estimation of polyurethane foams’ microstructure, what is crucial especially in the case of thermal insulation materials.

scholarly journals Effects of Droplet-Vitrification Cryopreservation Based on Physiological and Antioxidant Enzyme Activities ofBrassidiumShooting Star Orchid

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Safrina Rahmah ◽  
Safiah Ahmad Mubbarakh ◽  
Khor Soo Ping ◽  
Sreeramanan Subramaniam
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Liquid Nitrogen ◽  
Enzyme Activities ◽  
Structural Changes ◽  
Total Soluble Protein ◽  
Antioxidant Enzyme Activities ◽  
Droplet Vitrification ◽  
The Impact ◽  
Scanning Electron

Protocorm-like bodies (PLBs) ofBrassidiumShooting Star orchid were successfully cryopreserved using droplet-vitrification method. Vitrification based cryopreservation protocol is comprised of preculture, osmoprotection, cryoprotection, cooling, rewarming, and growth recovery and each and every step contributes to the achievement of successful cryopreservation. In order to reveal the lethal and nonlethal damage produced by cryopreservation, histological observation, scanning electron microscopy (SEM), and biochemical analysis were carried out in both cryopreserved and noncryopreserved PLBs ofBrassidiumShooting Star orchid comparing with the control PLBs stock culture. Histological and scanning electron microscopy analyses displayed structural changes in cryopreserved PLBs due to the impact of cryoinjury during exposure to liquid nitrogen. Total soluble protein significantly increased throughout the dehydration process and the highest value was achieved when PLBs were stored in liquid nitrogen. Ascorbate peroxidase (APX) and catalase (CAT) showed the highest enzyme activities in both dehydration and cryostorage treatments indicating that stress level of PLBs was high during these stages.

The Corrosion of HDG Zinc Coatings on the Road and Urban Infrastructures

2015 ◽  
Vol 227 ◽  
pp. 217-220
Author(s):  
Agnieszka Królikowska ◽  
Leszek Komorowski
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Corrosion Resistance ◽  
Gravimetric Method ◽  
Optical Emission ◽  
Emission Spectrometry ◽  
The Road ◽  
On The Road ◽  
Zinc Coatings ◽  
Scanning Electron

The standard ISO 14713-1 shows that HDG coatings should protect steel in the corrosive atmosphere C5 for 10–21 years. It was observed that pitting corrosion appears already after 2–3 years on roads and urban infrastructures and both Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) have shown that lead inclusions were present in all such corroded zinc coatings. The laboratory prepared HDG coatings with different amount of lead inclusions were investigated by gravimetric method (after exposure in salt chamber), SEM with EDS, and Glow Discharge Optical Emission Spectrometry (GDOES). The corrosion resistance was analyzed in the polarization tests and local probe techniques. The inclusions could accelerate coating corrosion because lead is cathodic to zinc.

Sign in / Sign up

Export Citation Format

Share Document