scholarly journals Nickel-Based Alloy Dry Milling Process Induced Material Softening Effect

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3758 ◽  
Author(s):  
Jun Zha ◽  
Zelong Yuan ◽  
Hangcheng Zhang ◽  
Yipeng Li ◽  
Yaolong Chen
Keyword(s):  
High Speed ◽  
Softening Temperature ◽  
Milling Process ◽  
Dry Milling ◽  
Milling Force ◽  
Softening Effect ◽  
Milling Temperature ◽  
Nickel Based Alloy ◽  
Alloy Softening ◽  
Milling Forces

Improving the cutting efficiency is the major factor for improving the processing of nickel-based alloys. The novelty of this research is the calibrated SiAlON ceramic tool dry milling nickel-based alloy process. Firstly, the nickel-based alloy dry milling process was analyzed through the finite element method, and the required milling force and temperature were deduced. Then, several dry milling experiments were conducted with the milling temperature, and the milling force was monitored. The change in cutting speeds was from 400 m/min to 700 m/min. Experimental results verified the reduction of the dry milling force hypothesized by the simulation. The experiment also indicated that with a cut depth of 0.3 mm, cut width of 6 mm, and feed per tooth of 0.03 mm/z, when milling speed exceeded 527.52 m/min, the milling force began to decrease, and the milling temperature exceeded the nickel-based alloy softening temperature. This indicated that easy cutting could be realized under high-speed dry milling conditions. The interpolation curve about average temperature and average milling forces showed similarity to the tensile strength reduction with the rise of temperature.

Experimental Study on Ball-End Milling of C/C Composite

2013 ◽  
Vol 650 ◽  
pp. 139-144
Author(s):  
Chen Wei Shan ◽  
Ying Zhao ◽  
Dong Peng Cui
Keyword(s):  
Prediction Model ◽  
High Speed ◽  
End Milling ◽  
Orthogonal Experiment ◽  
Carbon Matrix ◽  
Milling Process ◽  
Cutting Depth ◽  
Milling Force ◽  
Ball End Milling ◽  
Milling Forces

Along with the development of high speed machining technology, the ball end milling cutter’s application is more and more widely. An influence of four control parameters, namely feed, cutting depth, spindle speed and cutting width, on cutting forces is investigated. This paper focuses on experimental research of milling process of carbon fiber reinforced carbon matrix composite (C/C composite). The milling force prediction model for milling of composite using the carbide ball-end tools is built by orthogonal experiment. The experiment results show that : the reliability of the this prediction model is quite high, and the effect of milling speed on milling force is not very obvious, but the milling force increases with the increment of feed per tooth, milling depth and milling width. Using this information, a new prediction model for the milling forces is proposed that can be used for C/C composite milling.

Experimental Study on Thermal and Force Characteristics in the Dry Slotting of Cortical Bone

2016 ◽  
Vol 1136 ◽  
pp. 233-238
Author(s):  
Liang Wen ◽  
Zi Han Zhao ◽  
Jin Bang Song ◽  
De Dong Yu ◽  
Ming Chen ◽  
...  
Keyword(s):  
Cutting Force ◽  
Cortical Bone ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Temperature ◽  
Growth Direction ◽  
Milling Process ◽  
Spindle Speed ◽  
Milling Force ◽  
Milling Temperature

Cutting force and temperature are the two chief factors affecting bone rehabilitation during bone cutting in many orthopedic surgeries. To reveal new knowledge of thermal and force when milling cortical bone, slotting experiments were carried on high-speed milling platform. Cutting force and temperature were measured during the milling process. The effects of cutting inputs on cutting thermal and force were researched in detail. The results showed that: feed rate and spindle speed had a great impact on the milling temperature, while the milling force was mainly influenced by spindle speed. A feed rate of 1.0-1.4 mm/s is recommended to obtain preferable milling force and temperature, and a larger feed rate of 1.2-1.4 mm/s is advised to use with a lower spindle speed (8000-20000 r/min), while a smaller feed rate of 1.0-1.2 mm/s should be chosen when spindle speed was between 20000-40000 r/min. Feeding parallel to the growth direction of the cortical bone can significantly reduce the milling temperature, but there was no obvious change in milling force. The lowest cutting temperature obtained during the experiment was around 50 °C without coolant, which was acceptable for orthopedic surgeries.

scholarly journals Effect of High Speed Milling Process Parameters on the Milling Force and Surface Topography of AM50A Magnesium Alloy

2018 ◽  
Vol 36 (1) ◽  
pp. 124-131
Author(s):  
Hongji Zhang ◽  
Yuanyuan Ge ◽  
Hong Tang ◽  
Yaoyao Shi ◽  
Zengsheng Li
Keyword(s):  
Magnesium Alloy ◽  
Surface Quality ◽  
High Speed ◽  
Milling Process ◽  
Spindle Speed ◽  
Feed Speed ◽  
Milling Force ◽  
High Speed Milling ◽  
Milling Parameters

Within the scope of high speed milling process parameters, analyzed and discussed the effects of spindle speed, feed rate, milling depth and milling width on milling forces in the process of high speed milling of AM50A magnesium alloy. At the same time, the influence of milling parameters on the surface roughness of AM50A magnesium alloy has been revealed by means of the measurement of surface roughness and surface micro topography. High speed milling experiments of AM50A magnesium alloy were carried out by factorial design. Form the analysis of experimental results, The milling parameters, which have significant influence on milling force in high speed milling of AM50A magnesium alloy, are milling depth, milling width and feed speed, and the nonlinear characteristics of milling force and milling parameters. The milling force decreases with the increase of spindle in the given mill parameters. For the effects of milling parameters on surface quality of the performance, in the milling depth and feeding speed under certain conditions with the spindle speed increases the surface quality of AM50A magnesium alloy becomes better with the feed speed increases the surface quality becomes poor. When the spindle speed is greater than 12000r/min, the milling depth is less than 0.2mm, and the feed speed is less than 400mm/min, the milling surface quality can be obtained easily.

Study on Prediction Model and Experiments of High-Speed Milling Force for Stainless Steel 316

2010 ◽  
Vol 33 ◽  
pp. 6-10
Author(s):  
Wei Feng Zheng ◽  
Jing Quan Wu ◽  
Can Liu ◽  
Guang Hui Li ◽  
Guang Yu Tan
Keyword(s):  
Stainless Steel ◽  
High Speed ◽  
Significant Degree ◽  
Actual Condition ◽  
Linear Regression Method ◽  
Milling Force ◽  
High Speed Milling ◽  
Stainless Steel 316 ◽  
Milling Forces ◽  
Selection Of

Through the orthogonal test in which stainless steel 316 was milled with high speed by solid cemented carbide end cutter, the milling force was measured. By multiple linear regression method, the prediction formula of the milling forces of stainless steel 316 was found. In addition, this study validates to significant degree of the formula meeting the actual condition, which can provide a reference to better selection of cutting parameter in advance and the design of high-speed milling cutter.

Dynamic Force Identification in Peripheral Milling Based on CGLS Using Filtered Acceleration Signals and Averaged Transfer Functions

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Chenxi Wang ◽  
Xingwu Zhang ◽  
Baijie Qiao ◽  
Hongrui Cao ◽  
Xuefeng Chen
Keyword(s):  
Time Domain ◽  
Transfer Functions ◽  
Milling Process ◽  
Dynamic Force ◽  
Band Pass Filter ◽  
Peripheral Milling ◽  
Milling Force ◽  
Force Identification ◽  
Milling Forces ◽  
Acceleration Signals

Dynamic milling forces have been widely used to monitor the condition of the milling process. However, it is very difficult to measure milling forces directly in operation, particularly in the industrial scene. In this paper, a dynamic force identification method in time domain, conjugate gradient least square (CGLS), is employed for reconstructing the time history of milling forces using acceleration signals in the peripheral milling process. CGLS is adopted for force identification because of its high accuracy and efficiency, which handles the ill-conditioned matrix well. In the milling process, the tool with high-speed rotation has different transfer functions between tool nose and accelerometers at different angular positions. Based on this fact, the averaged transfer functions are employed to reduce the error amplification of regularization processing for milling force identification. Moreover, in order to eliminate the effect of idling and high-frequency components on identification accuracy, the Butterworth band-pass filter is adopted for acceleration signals preprocessing. Finally, the proposed method is validated by milling tests under different cutting parameters. Experimental results demonstrate that the identified and measured milling forces are in good agreement on the whole time domain, which verifies the effectiveness and generalization of the indirect method for milling force measuring. In addition, the Tikhonov regularization method is also implemented for comparison, which shows that CGLS has higher accuracy and efficiency.

Simulation of End Milling for Weak-Rigidity Structural Parts of Aluminium Alloy in Aviation

2011 ◽  
Vol 201-203 ◽  
pp. 332-336
Author(s):  
Chun Lin Fu ◽  
Cong Kang Wang ◽  
Tie Gang Li ◽  
Wan Shan Wang
Keyword(s):  
High Speed ◽  
End Milling ◽  
Element Model ◽  
Milling Process ◽  
Milling Force ◽  
Drilling Tool ◽  
Structural Parts ◽  
Aluminum Alloy 7075 ◽  
End Milling Process ◽  
Lower Material

To resolve the problem of the parts deformation because of the milling force, a finite element model (FEM) of end milling process simulation in milling force field was established. On the base of FEM, we simulate the high-speed end milling type structure of aluminum alloy 7075 parts. We successfully predict the end milling force, obtain the effect between the upper and lower material to the milling force, and Mises stress and the tool length beyond the part.The simulation results show that the lower material can increase the milling force to upper, and upper material can decrease milling force to lower layer.The drilling tool length beyond the part is about 0.5 mm .

Simulation of Three-Dimensional Dynamic Cutting Forces and Chatter Stability in Ball-End Milling

2010 ◽  
Vol 443 ◽  
pp. 302-307
Author(s):  
Jun Zhao ◽  
Xiao Feng Zhang ◽  
Han Bing Luo
Keyword(s):  
High Speed ◽  
End Milling ◽  
Three Dimensional ◽  
Milling Process ◽  
Ball End Milling ◽  
Parameters Selection ◽  
Nonlinear Dynamics Model ◽  
Dynamic Components ◽  
The Stability ◽  
Milling Forces

By taking into account the regenerative chatter vibration, a nonlinear dynamics model for high speed ball-end milling is proposed. The effect of dynamic components of milling forces on chatter is analyzed. A method to predict the stability limits of high speed ball-end milling process is proposed and the stability lobes diagram is simulated. The comparison of experimental milling forces with the simulation results indicates the high accuracy of the model and the effectiveness of the simulation algorithms. The proposed method provides a theoretical instruction for parameters selection and optimization in milling processing.

Experimental Study on Ball End Mill in Glass Machining at High Speed

2011 ◽  
Vol 314-316 ◽  
pp. 1167-1170
Author(s):  
Zhi Wei ◽  
Ji Hong Jia ◽  
Mei Lin Gu ◽  
Chao Zuo ◽  
Xing Zhen Jin
Keyword(s):  
High Speed ◽  
Experimental System ◽  
Milling Process ◽  
End Mill ◽  
Ball End Mill ◽  
Milling Force ◽  
Milling Tool ◽  
Explicit Analysis ◽  
Stress And Deformation ◽  
The Relationship

This paper describes the experimental system of milling force, the tool geometrical feature and the certain experimental condition in the section of experimental case, which also makes an explanation about the designing of experimental case and the analysis of the experimental data. It also represents the relationship between coefficients associated with the milling process and the milling force applied on the tool in detail. A finite element method is used to make an explicit analysis on the stress and deformation of the milling tool under the application of certain milling force. Finally, a summary is made to conclude the study and its results.

Study on Milling Force of High Volume Fraction SiCp/Al Composites with Ultrasonic Longitudinal and Torsional Vibration High Speed Milling

2014 ◽  
Vol 910 ◽  
pp. 114-117 ◽  
Author(s):  
Dao Hui Xiang ◽  
Guang Bin Yang ◽  
Song Liang ◽  
Yan Feng Wang ◽  
Qiang Qin
Keyword(s):  
Torsional Vibration ◽  
High Speed ◽  
Volume Fraction ◽  
Fold Increase ◽  
High Volume ◽  
High Volume Fraction ◽  
Milling Force ◽  
High Speed Milling ◽  
Milling Method ◽  
Milling Forces

High volume fraction SiCp/Al composites were milled in ultrasonic longitudinal and torsional vibration high speed milling and high speed milling in this experiment, study on effects of different milling parameters (milling depth ap, feed engagement fz, the milling speed vz) on milling force. The results shows that in the same cutting parameters ,the three milling force of ultrasonic longitudinal and torsional vibration high speed milling are smaller than that of high speed milling, and milling forces of two milling method increase with the add of the milling depth and feed engagement ,but they aren't fold increase. Milling forces of two milling method decrease with the add of the the minlling speed,and the changes become gently when the the minlling speed run up to 170m/min, with the further increase of the milling speed,ultrasonic vibration high speed milling will translate to high speed milling, this is because the torsional vibration is submerged.

Sign in / Sign up

Export Citation Format

Share Document